Search NASA⌕ Search

SEARCH · Search NASA

Results for “Padding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Grippers Based on Opposing Van Der Waals Adhesive Pads

Novel gripping structures based on van der Waals adhesive forces are disclosed. Pads covered with fibers can be activated in pairs by opposite forces, thereby enabling control of the adhesive force in an ON or OFF state. Pads can be used in groups, each comprising a group of opposite pads. The adhesive structures enable anchoring forces that can resist adverse forces from different directions. The adhesive structures can be used to enable the operation of robots on surfaces of space vehicles.

Parness, Aaron↗

Propulsion Overview of the Orion Pad Abort 1 (PA-1) Flight-Test Vehicle

The NASA Orion Flight Test Office was tasked with conducting a series of flight tests in several launch abort scenarios to certify that the Orion Launch Abort System is capable of delivering astronauts aboard the Orion Crew Module to a safe environment, away from a failed booster. The first of this series was the Orion Pad Abort 1 Flight-Test Vehicle, which was successfully flown on May 6, 2010 at the White Sands Missile Range in New Mexico. This presentation provides a concise overview of the three propulsive subsystems used on the Pad Abort 1 Flight-Test Vehicle. Although the Constellation program has been cancelled and the operational role of the Orion spacecraft has significantly evolved, lessons learned from Pad Abort 1 could certainly contribute to the vehicle architecture of many future human-rated space launch vehicles

Jones, Daniel S.↗

Development of an Ablative 3D Quartz / Cyanate Ester Composite for the Orion Spacecraft Compression Pad

With the successful flight test of the Orion Multipurpose Crew Vehicle last December, NASA is well on its way to sending humans into deep space with the goal of putting astronauts on Mars in the 2030s. Orion will receive some upgrades for its next launch in 2018 including a newly developed 3D Quartz Cyanate Ester composite material for the compression pad. The compression pads are 10-inches in diameter and 3-inches thick. The pucks are at 4 locations in the heat shield that serve as a part of the mechanism for holding the Crew and Service modules together during most mission phases prior to separation followed by Earth re-entry. Thus the compression pad has structural, aerothermal and thermal protection requirements.This paper describes the approach used for developing the new 3D composite, including continuous 3D weaving on an automated loom followed by resin transfer molding. Mechanical, thermal and arc jet testing of the 3D composite are also described.

Feldman, Jay↗

Development of an Ablative 3D Quartz / Cyanate Ester Composite for the Orion Spacecraft Compression Pad

With the successful flight test of the Orion Multipurpose Crew Vehicle last December, NASA is well on its way to sending humans into deep space with the ultimate goal of putting astronauts on Mars in the 2030s. Orion will receive some upgrades for its next launch in 2018 including a newly developed 3D quartz / cyanate ester composite material for the compression pad. Multiple pad locations in the heat shield serve as a part of the mechanism for holding the Crew and Service Modules together during most mission phases prior to separation followed by Earth re-entry of the Crew Module. Thus the compression pad must survive structural and aerothermal loads, and protect the adjascent structure and heat shield materials from over-heating.This paper describes the approach used for developing the new 3D composite, including continuous 3D weaving on an automated loom followed by resin transfer molding. Mechanical, thermal, arc jet ,and stress relaxation testing of the 3D composite are also described.

Feldman, Jay D.↗

On The Incorporation of Both Function-Driven Requirements and Topology Optimization in The Development of Lunar Launch & Landing Pads

In the design of additively manufactured structures, there can be a constant battle between focusing on function-driven design and topology optimization in an attempt to improve a products ability to meet all requirements. Function-driven optimization is defined as the process of identifying the best design parameters that satisfy project functionality requirements. Function-driven optimization is typically implemented by a designer(s) who, instead of computational limitations, has human bias for the input or inputs determined. On the other hand, topology optimization is defined as a mathematical method that optimizes material layout within a given design space, for a given set of loads, boundary conditions, and constraints with the goal of maximizing the performance of the system. In topology optimization, the work is defined by the limited mathematical inputs and computationally available goals/restraints. If not evaluated simultaneously, these two approaches can result in fundamentally different design concepts meant to address the same requirements. NASA’s Artemis program includes the development of a base camp near the lunar South Pole. After site selection is made, one of the first infrastructure elements needed will be a launch and landing pad (LLP). The construction of such a pad will prevent damage to nearby structures from plume-surface interaction (PSI) while also providing a stable platform for the lander. These benefits reduce the required distance between the established landing zones and other settlement infrastructure. In this paper, the authors evaluate the requirements associated with lunar LLP development, application of both functional and topological optimization techniques, methodologies to combine the two techniques, and potential impacts on final design of such a pad.

In-situ↗

Thermal Neutron Imaging Using A New Pad-Based Position Sensitive Neutron Detector

Thermal neutrons (with mean energy of 25 meV) have a scattering mean free path of about 20 m in air. Therefore it is feasible to find localized thermal neutron sources up to ~30 m standoff distance using thermal neutron imaging. Coded aperture thermal neutron imaging was developed in our laboratory in the nineties, using He-3 filled wire chambers. Recently a new generation of coded-aperture neutron imagers has been developed. In the new design the ionization chamber has anode and cathode planes, where the anode is composed of an array of individual pads. The charge is collected on each of the individual 5x5 mm2 anode pads, (48x48 in total, corresponding to 24x24 cm2 sensitive area) and read out by application specific integrated circuits (ASICs). The high sensitivity of the ASICs allows unity gain operation mode. The new design has several advantages for field deployable imaging applications, compared to the previous generation of wire-grid based neutron detectors. Among these are the rugged design, lighter weight and use of non-flammable stopping gas. For standoff localization of thermalized neutron sources a low resolution (11x11 pixel) coded aperture mask has been fabricated. Using the new larger area detector and the coarse resolution mask we performed several standoff experiments using moderated californium and plutonium sources at Idaho National Laboratory. In this paper we will report on the development and performance of the new pad-based neutron camera, and present long range coded-aperture images of various thermalized neutron sources.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Advanced Materials Testing for Lunar Landing & Launch Pad Construction

Five candidate lunar landing and launch pad candidate materials were evaluated in relevant Oxygen/Methane rocket engine plume environment exposure tests. The performance trends were modeled, observed, measured (to the extent possible), and testing results were evaluated. A total of fifteen high temperature plume tests were performed in two test campaigns: five in December 2020 and ten in March 2021. The results indicate that several of the selected materials are promising for future consideration in designing and building lunar landing and launch pads, although further development work is needed for all of them.

landing pad↗

Lunar and Martian Vertical Takeoff & Vertical Landing (VTVL) Pad Concepts

Landing space craft rocket plume exhaust interactions with the regolith surfaces on the Moon and Mars will result in cratering and regolith particle ejecta traveling at velocities up to 2,000 meters per second in the vacuum surroundings. This phenomenon creates hazards for the spacecraft that is landing or launching and may also cause damage to surrounding assets, personnel and infrastructure. One potential solution to this issue is to construct vertical takeoff and vertical landing (VTVL) pad infrastructure systems which will mitigate these rocket plume exhaust effects. Concepts will be presented for the construction and maintenance of such VTVL pads in lunar and martian environments.

Pad↗

High-speed x-ray imaging with the Keck pixel array detector (Keck PAD) for time-resolved experiments at synchrotron sources

Modern storage rings are readily capable of providing intense x-ray pulses, tens of picoseconds in duration, millions of times per second. Exploiting the temporal structure of these x-ray sources opens avenues for studying rapid structural changes in materials. Many processes (e.g. crack propagation, deformation on impact, turbulence, etc.) differ in detail from one sample trial to the next and would benefit from the ability to record successive x-ray images with single x-ray sensitivity while framing at 5 to 10 MHz rates. To this end, we have pursued the development of fast x-ray imaging detectors capable of collecting bursts of images that enable the isolation of single synchrotron bunches and/or bunch trains. The detector technology used is the hybrid pixel array detector (PAD) with a charge integrating front-end, and high-speed, in-pixel signal storage elements. A 384×256 pixel version, the Keck-PAD, with 150 µm × 150 µm pixels and 8 dedicated in-pixel storage elements is operational, has been tested at CHESS, and has collected data for compression wave studies. An updated version with 27 dedicated storage capacitors and identical pixel size has been fabricated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Characterization of 128 × 128 MM-PAD-2.1 ASIC: a fast framing hard x-ray detector with high dynamic range

Here, we characterize a new x-ray Mixed-Mode Pixel Array Detector (MM-PAD-2.1) Application Specific Integrated Circuit (ASIC). Using an integrating pixel front-end with dynamic charge removal architecture, the MM-PAD-2.1 ASIC extends the maximum measurable x-ray signal (in 20 keV photon units) to > 10 7 x-rays/pixel/frame while maintaining a low read noise across the full dynamic range, all while imaging continuously at a frame rate of up to 10 kHz. The in-pixel dynamic charge removal mechanism prevents saturation of the input amplifier and proceeds in parallel with signal integration to achieve deadtime-less measurements with incident x-ray rates of > 10 10 x-rays/pixel/s. The ASIC format consists of 128 × 128 square pixels each 150 μm on a side and is designed to be 3-side buttable so large arrays can be effectively tiled. Here we use both laboratory x-ray sources and the Cornell High Energy Synchrotron Source (CHESS) to characterize two single ASIC prototype detectors for both low (single x-ray) and high incident flux detection. In the first detector the ASIC was solder bump-bonded to a 500 μm thick Si sensor for efficient detection of x-rays below 20 keV, whereas the second detector used a 750 μm thick CdTe sensor for x-rays above ~20 keV.

36 MATERIALS SCIENCE↗

High-energy X-ray imaging with a Germanium MM-PAD hybrid pixel detector

Germanium is a high-Z sensor material with excellent energy resolution and attractive properties for high-energy photon detection. Despite its advantages, the need for cryogenic operation and challenges in the fabrication of pixelated high-purity germanium have hindered the development of segmented detectors. We report on the fabrication and performance of a germanium imaging detector with 150 μm pixel pitch hybridized to the MM-PAD ASIC. The detector was capable of high-resolution radiographic imaging and has a fast temporal response. Additionally, we describe the detector's upper operating temperature limits using both the MM-PAD and MARS ASICs, achieving stable operation up to 130 K and 190 K, respectively.

36 MATERIALS SCIENCE↗

Design and optimization of cancellation coil topologies for a ferrite-less wireless EV charging pad

Ferrite cores are widely used in conventional wireless EV charging pads to reduce stray EMF emissions, but they can be brittle, heavy, and expensive. This work furthers the development of ferrite-less wireless charging pads by comparing an active and two distinct passive cancellation coil topologies as candidates to replace the ferrite. Using the software packages FEMM and MATLAB, each topology is optimized to find the best winding positions and radii to minimize leakage at a specified position under the side of the vehicle. The optimized designs are compared for shielding effectiveness, induced current, and efficiency. All three topologies are able to sufficiently reduce the leakage field below the ICNIRP limit of 27 μTrms with just one turn. Interestingly, we find that an array of simple passive cancellation loops performs similar to the more widely studied passive cancellation coil.

Scher, Aaron D.↗

Transverse field-induced nucleation pad switching modes during domain wall injection

We have used magnetic transmission X-ray microscopy (M-TXM) to image in-field magnetization configurations of patterned Ni{sub 80}Fe{sub 20} domain wall 'injection pads' and attached planar nanowires. Comparison with micromagnetic simulations suggests that the evolution of magnetic domains in rectangular injection pads depends on the relative orientation of closure domains in the remanent state. The magnetization reversal pathway is also altered by the inclusion of transverse magnetic fields. These different modes explain previous results of domain wall injection into nanowires. Even more striking was the observation of domain walls injecting halfway across the width of wider (>400 nm wide) wires but over wire lengths of several micrometers. These extended Neel walls can interact with adjacent nanowires and cause a switching in the side of the wire undergoing reversal as the domain wall continues to expand.

36 MATERIALS SCIENCE↗

Cape EGS: Frisco Pad Wells Flow Test Microseismic Data

This dataset contains microseismic data acquired during the Frisco pad flow test project led by Fervo Energy, conducted between July 17th - Aug 12th 2024, near the Utah FORGE geothermal site. The microseismic data was collected from various Utah FORGE wells: via Distributed Acoustic Sensing (DAS) fiber in 16B, and two 3-component geophones located in wells 56-32 and 78B. The dataset is structured in SEGY format, where the first six traces represent data from the geophones, and the remaining traces capture DAS data from well 16B. Each SEGY file in this dataset contains triggered microseismic events, with event initiation based on Short-Time Average over Long-Time Average (STA/LTA) detection criteria during the stimulation process. Files are grouped by time intervals and named following the structure "[WellPad][WellName][Month]_[Year]Divine_Trigger[EventNumber].sgy," indicating well pad, well name, date, and event number. Sampling parameters include a spatial sampling of approximately 2 meters for DAS channels and a temporal sampling rate of 2000 Hz, with each data record spanning 1.2 seconds. The files' coordinates are referenced to the location of the FORGE 16A-32 wellhead, positioned at UTM coordinates: Easting 334641.1891 m and Northing 4263443.693 m. The geographic coordinates for this origin are 38.50402147 latitude and -112.8963897 longitude, with an elevation of 1650.0249 meters above sea level.

15 GEOTHERMAL ENERGY↗

Dunham Pad A 4H Well

Medical CT scans, raw and processed core logging data (including XRF) and core images of the Dunham Pad A 4H well, obtained by Triana Energy, as supplemental information to the NETL Technical Report Series Crandall, D.; Brown, S.; Moore, J.; Martin, K.; Mackey, P.; Carr, T. CT Scanning and Geophysical Measurements of the Marcellus Formation from the Dunham Pad A 4H Well NETL-TRS-X-2018; NETL Technical Report Series; U.S. Department of Energy, National Energy Technology Laboratory: Morgantown, WV, 2018; p 48.

Core Logs↗

Historical Material Analysis of DC745U Pressure Pads

As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic® DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter® brand product line. Currently, DC745U is available through Xiameter® or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged DC745U. 5. NMR, solvent swelling, thermal, and mechanical studies on radiolytically aged DC745U. Each area is reviewed and further work is suggested to improve our understanding of DC745U for systems engineering, surveillance, aging assessments, and lifetime assessment.

36 MATERIALS SCIENCE↗

Low Temperature Studies on DC745U Pressure Pads

DC745U is a silica-filled solid silicone elastomer used to manufacture pressure pads for a variety of applications. The material is proprietary to Dow Corning and thus very little information on its composition and properties is available. A considerable amount of characterization work has been conducted (Denisse Ortiz-Acosta W-1-TR-0098U/ LA-UR-12-23612) on DC745U. Based on these studies an estimate of the composition of the polymer was obtained. DC745U is composed of ≤ 100 wt% dimethyl siloxane repeat units, ≤1.5 wt% of methylphenyl siloxane, and ≤ 1 wt% methylvinyl siloxane groups. The methylvinyl siloxane groups are used as crosslink sites. The polymer is cured using a vinyl-specific peroxide, Varox DBPH-50, at 160ºC to form a polymer network. The structure and composition of this polymer network provide DC745U its unique properties. The methylphenyl siloxane repeat unit was added to improve DC745U’s thermal properties when compared to polydimethylsiloxane (PDMS). PDMS has a glass transition temperature of -120ºC and a melting temperature of -40ºC. It is believed that the phenyl group in DC745U improves thermal properties by inhibiting crystallization. This report describes the results obtained from low temperature thermal, mechanical and molecular characterization. These studies were conducted to improve our understanding of low temperature crystallization kinetics and thermal kinetics under compression strain and to determine if the pad undergoes stress deformations under these extreme conditions. Results described herein address several knowledge gaps previously stated in the report W-1-TR-0098U. Experiments described here include Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), Nuclear Magnetic Resonance (NMR), and mechanical (stress/strain) tests.

36 MATERIALS SCIENCE↗

Steady state and transient temperature distributions in the human thigh covered with a cooling pad

An analytical and experimental study was done on the performance of cooling pads attached to a human thigh. Each cooling pad consisted of a long, water cooled tube formed into a serpentine shape with uniform spacing between the parallel sections. The analytical work developed a cylindrical model for the human thigh. The transient times predicted by this model ranged from 25 to 80 minutes, which is reasonably close to the experimental results. Calculated and measured steady state temperature profiles were in fair agreement. The transient times associated with a change from a high metabolic rate of 1800 Btu/hr (528 w) to a low level of 300 Btu/hr (88 w), were found to be about 120 minutes. A change from 300 Btu/hr (264 w) to 300 Btu/hr (88 w) resulted in 90 to 100 minute transients. However, the transient times for a change in metabolic rate in the opposite direction from 300 Btu/hr (88 w) to 1800 Btu/hr (528 w) were 40 to 60 minutes.

Leo, R. J.↗