Search NASA⌕ Search

SEARCH · Search NASA

Results for “Particle Separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

A two-stage virtual impactor for continuous concentration of particles in an aerosol

A two-stage virtual impactor has been designed and fabricated to concentrate aerosol particles. In this impactor, the minor flow from the first stage of the impactor is introduced into the second stage as the primary flow. The cut-point of the impactor is designed to be about 0.3 micron. The sample aerosol is introduced into the impactor at a flow rate of 8.0 atm-l/min and after the two stages of separation, particles are collected into the minor flow of 0.06 atm-l/min with 84 percent efficiency. The tandem arrangement of the two stages increases the concentration of larger particles by a factor of greater than 100. The small size and the low flow rates make the impactor compatible with the sampling requirements of instruments used for the chemical and physical characterization of particles from low-particle number density aerosols. In particular, the high particle concentration factor of the impactor will make it possible to analyze individual particles in real time from aerosols containing less than 10 particles per cft by the mass spectrometric methods developed in our laboratory.

Sinha, M. P.↗
NASA NTRS1994

Electrophoretic interactions and aggregation of colloidal biological particles

The separation of cells or particles from solution has traditionally been accomplished with centrifuges or by sedimentation; however, many particles have specific densities close to unity, making buoyancy-driven motion slow or negligible, but most cells and particles carry surface charges, making them ideal for electrophoretic separation. Both buoyancy-driven and electrophoretic separation may be influenced by hydrodynamic interactions and aggregation of neighboring particles. Aggregation by electrophoresis was analyzed for two non-Brownian particles with different zeta potentials and thin double layers migrating through a viscous fluid. The results indicate that the initial rate of electrophoretically-driven aggregation may exceed that of buoyancy-driven aggregation, even under conditions in which buoyancy-driven relative motion of noninteracting particles is dominant.

Davis, Robert H.↗
DOE OSTI2021

Improved semiclassical model for real-time evaporation of matrix black holes

In this paper, we study real-time classical matrix mechanics of a simplified 2 × 2 matrix model inspired by the black hole evaporation problem. This is a step towards making a quantitative model of real-time evaporation of a black hole, which is realized as a bound state of D0-branes in string theory. The model we study is the reduction of Yang–Mills in 2 + 1 dimension to 0 + 1 dimensions, which has been corrected with an additional potential that can be interpreted as a zero-point energy for fermions. Our goal is to understand the lifetime of such a classical bound state object in the classical regime. To do so, we pay particular attention to when D-particles separate to check that the “off-diagonal modes” of the matrices become adiabatic and use that information to improve on existing models of evaporation. It turns out that the naive expectation value of the lifetime with the fermionic correction is infinite. This is a logarithmic divergence that arises from very large excursions in the separation between the branes near the threshold for classical evaporation. The adiabatic behavior lets us get some analytic control of the dynamics in this regime to get this estimate. This divergence is cutoff in the quantum theory due to quantization of the adiabatic parameter, resulting in a long lifetime of the bound state, with a parametric dependence of order log(1/ℏ).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

A coarse-grained model of clay colloidal aggregation and consolidation with explicit representation of the electrical double layer

The aggregation of clay minerals in liquid water exemplifies colloidal self-assembly in nature. These negatively charged aluminosilicate platelets interact through multiple mechanisms with different sensitivities to particle shape, surface charge, aqueous chemistry, and interparticle distance and exhibit complex aggregation structures. Experiments have difficulty resolving the associated colloidal assemblages at the scale of individual particles. Conversely, all-atom molecular dynamics (MD) simulations provide detailed insight on clay colloidal interaction mechanisms, but they are limited to systems containing a few particles. We develop a new coarse-grained (CG) model capable of representing assemblages of hundreds of clay particles with accuracy approaching that of MD simulations, at a fraction of the computational cost. Our CG model is parameterized based on MD simulations of a pair of smectite clay particles in liquid water. A distinctive feature of our model is that it explicitly represents the electrical double layer (EDL), i.e., the cloud of charge-compensating cations that surrounds the clay particles. Our model captures the simultaneous importance of long-range colloidal interactions (i.e., interactions consistent with simplified analytical models, already included in extant clay CG models) and short-range interactions such as ion correlation and surface and ion hydration effects. The resulting simulations correctly predict, at low solid-water ratios, the existence of ordered arrangements of parallel particles separated by water films with a thickness up to ~10 nm and, at high solid-water ratios, the coexistence of crystalline and osmotic swelling states, in agreement with experimental observations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Mesocrystal growth through oriented sliding and attachment of nanoplates

Oriented attachment is a critical, yet poorly understood, crystal growth pathway based on the self-assembly of nanocrystals. During oriented attachment, solvent-separated particles align and coalesce through forces that enable precise rotation and translation. While prior studies emphasized intragap forces driving crystallographic alignment, the forces enabling uniform stacking and superlattice formation remain unclear. Here, we demonstrate how macroscopic gibbsite mesocrystals emerge from nanoplates guided into staggered positions by directional sliding. Electron microscopy and X-ray scattering reveal the monoclinic superlattice structure, based on nanoplate stacking with a uniform ≈50° stagger along the gibbsite [010] direction. In situ liquid-cell TEM captures preferential sliding along the gibbsite [010] direction, decelerating with increasing particle overlap. Molecular dynamics simulations reveal that this staggered arrangement corresponds to a global free-energy minimum, rather than full alignment. The simulations also confirm that sliding along the [010] direction is energetically favored and provide insight into the role of interfacial water in achieving long-range ordered assemblies. These insights highlight the energy landscape’s role in oriented attachment, with implications for material synthesis and hierarchical structures in nature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

NFE-24-10417: Durability and Life-time Energy Performance Enhancement of Vapor Compression Systems

This project investigated the use of a Centrifugal Particle Separation (CPS) system to improve the durability and operational reliability of outdoor heat exchangers in vapor-compression based heating, ventilation, air conditioning, and refrigeration (HVACR) systems. The developed method introduced a novel dust and fouling mitigation approach by integrating an ambient air pre-cleaner that employs centrifugal forces to remove particulate matter from incoming air before it reaches the heat exchanger. By reducing the accumulation of dust and debris on coil surfaces, the CPS system aims to lower maintenance requirements and extend equipment lifespan. The project specifically involves coupling a centrifugal air pre-cleaner with a single-zone ductless mini-split system and evaluating its effectiveness in maintaining cleaner coil surfaces. Additionally, the study examined the impact of CPS integration on system energy performance. Through controlled experimental testing and performance monitoring, this work seeks to validate CPS-based air pre-cleaning as a practical, efficient solution for mitigating outdoor coil dust accumulation and fouling in both residential and commercial HVACR applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1972

Regenerative particulate filter development

Development, design, and fabrication of a prototype filter regeneration unit for regenerating clean fluid particle filter elements by using a backflush/jet impingement technique are reported. Development tests were also conducted on a vortex particle separator designed for use in zero gravity environment. A maintainable filter was designed, fabricated and tested that allows filter element replacement without any leakage or spillage of system fluid. Also described are spacecraft fluid system design and filter maintenance techniques with respect to inflight maintenance for the space shuttle and space station.

Descamp, V. A.↗
NASA NTRS1979

Materials and structural aspects of advanced gas-turbine helicopter engines

The key to improved helicopter gas turbine engine performance lies in the development of advanced materials and advanced structural and design concepts. The modification of the low temperature components of helicopter engines (such as the inlet particle separator), the introduction of composites for use in the engine front frame, the development of advanced materials with increased use-temperature capability for the engine hot section, can result in improved performance and/or decreased engine maintenance cost. A major emphasis in helicopter engine design is the ability to design to meet a required lifetime. This, in turn, requires that the interrelated aspects of higher operating temperatures and pressures, cooling concepts, and environmental protection schemes be integrated into component design. The major material advances, coatings, and design life-prediction techniques pertinent to helicopter engines are reviewed; the current state-of-the-art is identified; and when appropriate, progress, problems, and future directions are assessed.

Freche, J. C.↗
NASA NTRS1979

The erosion/corrosion of small superalloy turbine rotors operating in the effluent of a PFB coal combustor

Superalloy turbine rotors in a single stage turbine with 6 percent partial admittance were operated in the effluent of a pressurized fluidized bed coal combustor for up to 164 hours. Total mass flow was 300 kg/hr and average particulate loadings ranged from 600 to 2800 ppm for several coal/sorbent combinations. A 5.5 atm turbine inlet gas pressure and inlet gas temperatures from 700 to 800 C yielded absolute gas velocities at the stator exit of about 500 m/s. The angular rotation speed (40,000 rpm) of the six inch diameter rotors was equivalent to a tip speed of about 300 m/s, and average gas velocities relative to the rotating surface ranged from 260 to 330 m/s at mean radius. The rotor erosion pattern reflects heavy particle separation with severe (5 to 500 cm/yr) erosion at the leading edge, pressure side center, and suction side trailing edge at the tip. The erosion distribution pattern provides a spectrum of erosion/oxidation/deposition as a function of blade position. This spectrum includes enhanced oxidation (10 to 100 x air), mixed oxides in exposed depletion zones, sulfur rich oxides in deposition zones, and rugged areas of erosive oxide removal.

Zellars, G. R.↗
NASA NTRS1979

Materials and structural aspects of advanced gas-turbine helicopter engines

Advances in materials, coatings, turbine cooling technology, structural and design concepts, and component-life prediction of helicopter gas-turbine-engine components are presented. Stationary parts including the inlet particle separator, the front frame, rotor tip seals, vanes and combustors and rotating components - compressor blades, disks, and turbine blades - are discussed. Advanced composite materials are considered for the front frame and compressor blades, prealloyed powder superalloys will increase strength and reduce costs of disks, the oxide dispersion strengthened alloys will have 100C higher use temperature in combustors and vanes than conventional superalloys, ceramics will provide the highest use temperature of 1400C for stator vanes and 1370C for turbine blades, and directionally solidified eutectics will afford up to 50C temperature advantage at turbine blade operating conditions. Coatings for surface protection at higher surface temperatures and design trends in turbine cooling technology are discussed. New analytical methods of life prediction such as strain gage partitioning for high temperature prediction, fatigue life, computerized prediction of oxidation resistance, and advanced techniques for estimating coating life are described.

Freche, J. C.↗
NASA NTRS1979

The erosion/corrosion of small superalloy turbine rotors operating in the effluent of a PFB coal combustor

The operation of a turbine in the effluent of a pressurized fluidized bed (PFB) coal combustor presents serious materials problems. Synergistic erosion/corrosion and deposition/corrosion interactions may favor the growth of erosion-resistant oxides on blade surfaces, but brittle cracking of these oxides may be an important source of damage along heavy particle paths. Integrally cast alloy 713LC and IN792 + Hf superalloy turbine rotors in a single-stage turbine with 6% partial admittance have been operated in the effluent of a PFB coal combustor for up to 164 hr. The rotor erosion pattern exhibits heavy particle separation with severe erosion at the leading edge, pressure side center, and suction side trailing edge at the tip. The erosion distribution pattern gives a spectrum of erosion/oxidation/deposition as a function of blade position. The data suggest that preferential degradation paths may exist even under the targeted lower loadings (less than 20 ppm).

Zellars, G. R.↗
NASA NTRS1980

The assembly and properties of protobiological structures - The beginnings of cellular peptide synthesis

New data indicate that lysine-rich proteinoids have the ability to catalyze the synthesis of peptide bonds from a variety of amino acids and ATP. This capacity is evident in aqueous solution, in suspension of phase-separated complexes of lysine-rich proteinoid with acidic proteinoids, and in suspension of phase-separated particles composed of lysine-rich proteinoids with polynucleotides. Since the proteinoid complexes can contain other catalytic activities, including ability to catalyze internucleotide bond formation, it is inferred that the first protocells on earth already had a number of biological types of activity.

Fox, S. W.↗
NASA NTRS1983

The aerodynamic design and performance of the General Electric/NASA EEE fan

The aerodynamic design and test results of the fan and quarter-stage component for the GE/NASA Energy Efficient Engine (EEE) are presented. The fan is a high bypass ratio, single-stage design having 32 part-span shrouded rotor blades, coupled with a unique quarter-stage arrangement that provides additional core-stream pressure ratio and particle separation. The fan produces a bypass pressure ratio of 1.65 at the exit of the low aspect ratio vane/frame and a core-stream pressure ratio of 1.67 at the entrance to the core frame struts. The full-scale fan vehicle was instrumented, assembled and tested as a component in November 1981. Performance mapping was conducted over a range of speeds and bypass ratios using individually-controlled bypass and core-stream discharge valves. The fan bypass and core-stream test data showed excellent results, with the fan exceeding all performance goals at the important engine operating conditions.

Sullivan, T. J.↗
NASA NTRS1983

Computation of internal flows: Methods and applications; Proceedings of the Energy Sources Technology Conference, New Orleans, LA, February 12-16, 1984

The present conference covers computational method applications, viscous-inviscid interaction techniques, viscous flow computational methods, and design-related methods. Attention is given to viscous flows in turbomachinery cascades, forbidden signals and apparent Mach numbers in supersonic cascades, the flow field in an engine particle separator, two-dimensional separated channel flows, turbulent separating flows over a rearward-facing step, the semielliptic analysis of two-dimensional internal and compressible viscous flows, spline solutions of the incompressible Navier-Stokes equations in a mildly nonorthogonal coordinate system, the design of highly loaded blades with blockage in cascade, and a finite analytic method for unsteady, three-dimensional Navier-Stokes equations.

Sockol, P. M.↗
NASA NTRS1984

Response of a small-turboshaft-engine compression system to inlet temperature distortion

An experimental investigation was conducted into the response of a small-turboshaft-engine compression system to steady-state and transient inlet temperature distortions. Transient temperature ramps range from less than 100 K/sec to above 610 K/sec and generated instantaneous temperatures to 420 K above ambient. Steady-state temperature distortion levels were limited by the engine hardware temperature list. Simple analysis of the steady-state distortion data indicated that a particle separator at the engine inlet permitted higher levels of temperature distortion before onset of compressor surge than would be expected without the separator.

Biesiadny, T. J.↗
NASA NTRS1987

Experimental, water droplet impingement data on two-dimensional airfoils, axisymmetric inlet and Boeing 737-300 engine inlet

An experimental method has been developed to determine the droplet impingement characteristics on two- and three-dimensional bodies. The experimental results provide the essential droplet impingement data required to validate particle trajectory codes, used in aircraft icing analyses and engine inlet particle separator analyses. A body whose water droplet impingement characteristics are required is covered at strategic locations by thin strips of moisture absorbing (blotter) paper, and then exposed to an air stream containing a dyed-water spray cloud. Water droplet impingement data are extracted from the dyed blotter strips, by measuring the optical reflectance of the dye deposit on the strips, using an automated reflectometer. Impingement efficiency data obtained for a NACA 65(2)015 airfoil section, a supercritical airfoil section, and Being 737-300 and axisymmetric inlet models are presented in this paper.

Papadakis, M.↗
NASA NTRS1991

Experimental water droplet impingement data on modern aircraft surfaces

An experimental method has been developed to determine the water droplet impingement characteristics on two- and three-dimensional aircraft surfaces. The experimental water droplet impingement data are used to validate particle trajectory analysis codes that are used in aircraft icing analyses and engine inlet particle separator analyses. The aircraft surface is covered with thin strips of blotter paper in areas of interest. The surface is then exposed to an airstream that contains a dyed-water spray cloud. The water droplet impingement data are extracted from the dyed blotter paper strips by measuring the optical reflectance of each strip with an automated reflectometer. Preliminary experimental and analytical impingement efficiency data are presented for a NLF(1)-0414F airfoil, s swept MS(1)-0317 airfoil, a swept NACA 0012 wingtip and for a Boeing 737-300 engine inlet model.

Papadakis, Michael↗
NASA NTRS1990

ATTAP/AGT101 - Year 2 progress in ceramic technology development

The progress made by the Advanced Turbine Technology Applications Project (ATTAP) is summarized, with emphasis on the following areas: ceramic materials assessment and characterization, ceramic impact damage assessment, ceramic combustor evaluation, turbine inlet particle separator development, impact-tolerant turbine designs, and net-shape ceramic component fabrications. In the evolutionary ceramics development in the Automotive Gas Turbine (AGT101) and ATTAP programs initial designs were conceived to reduce stresses by using well-established criteria: bodies of revolution were preferred over nonaxisymmetric geometries, sharp corners were avoided, the contact area between components was kept as large as possible, and small parts were preferred over large when feasible. Projects discussed include: initial ceramic component fabrication by ceramic suppliers in 1990, engine test to 1371 C in 1991, 100-hr test bed engine durability test in 1991, and 300-hr test bed engine durability in 1992.

Kidwell, J. R.↗