Search NASA⌕ Search

SEARCH · Search NASA

Results for “Performance enhancement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Low-Speed Performance Enhancement using Localized Active Flow Control: Simulations, Scaling and Design of Localized Active Flow Control on the Common Research Model (4/4)

This report is dedicated to the application of localized AFC on the NASA CRM-HL wind tunnel model, with focus on the aileron application discussed in the CFD study (final report document #2). The experience developed for the Reference Aircraft guided the implementation on the CRM model. CFD evaluations are performed on a representative high-lift configuration, for a set of aileron deflections, and at relevant flow conditions. Alternative flow control actuator layouts are proposed and design consideration for practical integration into the existing CRM-HL model are set forth. The CFD simulations indicate that the aerodynamic performance improvements due to AFC obtained for the CRM-HL are consistent with those achieved for the Reference Aircraft. The observed changes in L/D are smaller than for the Reference Aircraft because the CRM has a higher leading edge sweep angle and a different relative aileron size. Conceptual design studies confirmed that the integration of an AFC equipped aileron into the existing wind tunnel model is feasible.

AFC↗
NASA NTRS2001

Autogenic Feedback Training Exercise and pilot performance: enhanced functioning under search-and-rescue flying conditions

Studies have shown that autonomous mode behavior is one cause of aircraft fatalities due to pilot error. In such cases, the pilot is in a high state of psychological and physiological arousal and tends to focus on one problem, while ignoring more critical information. This study examined the effect of training in physiological self-recognition and regulation, as a means of improving crew cockpit performance. Seventeen pilots were assigned to the treatment and control groups matched for accumulated flight hours. The treatment group contained 4 pilots from HC-130 Hercules aircraft and 4 HH-65 Dolphin helicopter pilots; the control group contained 3 pilots of HC-130s and 6 helicopter pilots. During an initial flight, physiological data were recorded on each crewmember and an instructor pilot rated individual crew performance. Eight crewmembers were then taught to regulate their own physiological response levels using Autogenic-Feedback Training Exercise (AFTE). The remaining participants received no training. During a second flight, treatment participants showed significant improvement in performance (rated by the same instructor pilot as in pretests) while controls did not improve. The results indicate that AFTE management of high states of physiological arousal may improve pilot performance during emergency flying conditions.

NASA Discipline Neuroscience↗
DOE OSTI2024

Performance enhancement of aqueous ionic liquids with lower critical solution temperature (LCST) behavior through ternary mixtures

Thermally responsive ionic liquids (ILs) exhibit liquid–liquid phase separation when mixed with water and heated above a lower critical solution temperature (LCST), resulting in a water-rich (WR) and an IL-rich (ILR) phase. These binary IL–water mixtures can be employed in a variety of thermodynamic processes such as forward osmosis (FO) desalination, for which two solution properties are desirable: low phase separation temperature and high osmotic strength (osmolality). However, these two properties are interlinked, with ILs that exhibit higher osmotic strengths typically requiring higher phase separation temperatures. This behavior tends to arise from the hydrophilicity of the IL cations, which enhances osmotic strength while also elevating the phase separation temperature. In this work, we highlight a pathway to overcome this tradeoff by developing ternary IL mixtures (two ILs with varying cation hydrophilicity mixed with water), which lowers the phase separation temperature while maintaining and even enhancing the osmotic strength of the solution. We characterize the mixing behavior (osmolality, phase separation temperature, WR phase purity, and WR to ILR phase mass ratio) of four ILs as a function of their concentration in solution. We find that an enhancement of up to 81.6% in the osmolality with a concomitant reduction of up to 15.4% in the phase separation temperature can be achieved using this approach. The ternary mixture is also shown to improve the phase separation kinetics by nearly 95% compared to the binary mixture. Overall, this work highlights a new pathway to improve the performance of LCST ILs for water and energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A completely precious metal–free alkaline fuel cell with enhanced performance using a carbon-coated nickel anode

Significance We present a groundbreaking advance in completely nonprecious hydrogen fuel cell technologies achieving a record power density of 200 mW/cm 2 with Ni@CN x anode and Co−Mn cathode. The 2-nm CN x coating weakens the O-binding energy, which effectively mitigates the undesirable surface oxidation during hydrogen oxidation reaction (HOR) polarization, leading to a stable fuel cell operation for Ni@CN x over 100 h at 200 mA/cm 2 , superior to a Ni nanoparticle counterpart. Ni@CNx exhibited a dramatically enhanced tolerance to CO relative to Pt/C, enabling the use of hydrogen gas with trace amounts of CO, critical for practical applications. The complete removal of precious metals in fuel cells lowers the catalyst cost to virtually negligible levels and marks a milestone for practical alkaline fuel cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Origin of enhanced performance when Mn-rich rocksalt cathodes transform to δ -DRX

Most Mn-rich cathodes are known to undergo phase transformation into structures resembling spinel-like ordering upon electrochemical cycling. Recently, the irreversible transformation of Ti-containing Mn-rich disordered rock-salt cathodes into a phase — named δ — with nanoscale spinel-like domains has been shown to increase energy density, capacity retention, and rate capability. However, the nature of the boundaries between domains and their relationship with composition and electrochemistry are not well understood. In this work, we discuss how the transformation into the multi-domain structure results in eight variants of Spinel domains, which is crucial for explaining the nanoscale domain formation in the δ -phase. We study the energetics of crystallographically unique boundaries and the possibility of Li-percolation across them with a fine-tuned CHGNet machine learning interatomic potential. Energetics of 16 d vacancies reveal a strong affinity to segregate to the boundaries, thereby opening Li-pathways at the boundary to enhance long-range Li-percolation in the δ structure. Defect calculations of the relatively low-mobility Ti show how it can influence the extent of Spinel ordering, domain morphology and size significantly; leading to guidelines for engineering electrochemical performance through changes in composition.

Anand, Shashwat↗
DOE OSTI2025

NFE-24-10417: Durability and Life-time Energy Performance Enhancement of Vapor Compression Systems

This project investigated the use of a Centrifugal Particle Separation (CPS) system to improve the durability and operational reliability of outdoor heat exchangers in vapor-compression based heating, ventilation, air conditioning, and refrigeration (HVACR) systems. The developed method introduced a novel dust and fouling mitigation approach by integrating an ambient air pre-cleaner that employs centrifugal forces to remove particulate matter from incoming air before it reaches the heat exchanger. By reducing the accumulation of dust and debris on coil surfaces, the CPS system aims to lower maintenance requirements and extend equipment lifespan. The project specifically involves coupling a centrifugal air pre-cleaner with a single-zone ductless mini-split system and evaluating its effectiveness in maintaining cleaner coil surfaces. Additionally, the study examined the impact of CPS integration on system energy performance. Through controlled experimental testing and performance monitoring, this work seeks to validate CPS-based air pre-cleaning as a practical, efficient solution for mitigating outdoor coil dust accumulation and fouling in both residential and commercial HVACR applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1986

STS performance enhancements for a heads up ascent design

A method of increasing the STS (space transportation system) lift capability by flying the SSV (Space Shuttle vehicle) in a heads up attitude during the first stage atmospheric flight as opposed to the current heads down attitude is presented. The paper reveals that the STS lift capability and SRM (solid rocket motor) burnrate definition are sensitive to the magnitude and direction of normal aerodynamic force acting on the SSV during atmospheric ascent. The STS operational trajectory design angle of attack will permit increases in SRM burnrate definition and STS lift capability for the proposed heads up ascent when compared to the current heads down ascent. For a heads up ascent the SRM burnrate can be increased 7 percent with a corresponding 4000 lb increase in STS lift capability. A comparison of the heads up and heads down ascent reveals similar performance trades for changes in trajectory shaping parameters and SRM and SSME (Space Shuttle main engine) performance characteristics.

Millard, S. W.↗
DOE OSTI2024

Single-source pulsed laser-deposited perovskite solar cells with enhanced performance via bulk and 2D passivation

Single-source vapor deposition of halide perovskites has, to date, remained challenging due to the dissimilar volatilities of the precursors, limiting the controlled transfer of multiple elements at once. Here, we demonstrate that pulsed laser deposition (PLD) addresses the rate-control challenges of single-source evaporation, enabling perovskite solar cells with power conversion efficiencies above 19% after passivation. Combining dry mechanochemical synthesis and PLD, we fabricated (Cl-passivated) MA1−xFAxPbI3 films from a single-source target. These films grow on hole-selective self-assembled monolayers, initially forming a thin PbI2-rich layer, which fully converts to perovskite. An oleylammonium iodide (OAmI) post-treatment is then applied to passivate the perovskite’s top surface by forming a 2D perovskite film. Incorporating PbCl2 in the target and applying OAmI-based 2D passivation results in a remarkable 19.7% efficiency for p-i-n perovskite solar cells with enhanced device stability. This highlights the appeal of PLD to fully unlock the potential of single-source vapor-deposited perovskites.

Soto-Montero, Tatiana↗
DOE OSTI2023

Microstructure and defect engineering of graphite anodes by pulsed laser annealing for enhanced performance of lithium-ion batteries

We report nanosecond pulsed laser annealing significantly improves cyclability and current carrying capacity of lithium-ion batteries (LIBs). This improvement is achieved by engineering of microstructure and defect contents present in graphite in a controlled way by using pulsed laser annealing (PLA) to increase the number density of Li + ion trapping sites. The PLA treatment causes the following changes: (1) creates surface steps and grooves between the grains to improve Li + ion charging and intercalation rates; (2) removes inactive polyvinylidene difluoride (PVDF) binder from the top of graphite grains and between the grains which otherwise tends to block the Li + migration; and (3) produces carbon vacancies in (0001) planes which can provide Li + charging sites. From X-ray diffraction data, we find upshift in diffraction peak or reduction in planar spacing, from which vacancy concentration was estimated to be about 1.0%, which is higher than the thermodynamic equilibrium concentration of vacancies. The laser treatment creates single and multiple C vacancies which provide sites for Li + ions, and it also produces steps and grooves for Li + ions to enter the intercalating sites. It is envisaged that the formation of these sites enhances Li+ ion absorption during charge and discharge cycles. The current capacity increases from an average 360 mAh/g to 430 mAh/g, and C–V shows significant reduction in SEI layer formation after the laser treatment. If the vacancy concentration is too high and charge-discharge cycles are long, then trapping of electrons by Li + may occur, which can lead to Li 0 formation and Li plating causing reduction in current capacity.

25 ENERGY STORAGE↗
NASA NTRS1994

Maneuver Performance Enhancement for an Advanced Fighter/Attack Aircraft

A small scale wind tunnel test of a realistic fighter configuration has been completed in NASA Ames' 7'x10' wind tunnel. This test was part of the Fighter Lift and Control (FLAC) program, a joint NASA - USAF research program, involving small and large-scale wind-tunnel tests and computational analysis of unique lift augmentation and control devices. The goal of this program is to enhance the maneuver and control capability of next-generation Air Force multi-role fighter aircraft with low-observables geometries. The principal objective of this test was to determine the effectiveness of passive boundary layer control devices at increasing L/D at sustained maneuver lift coefficients. Vortex generators (VGs) were used to energize the boundary layer to prevent or delay separation. Corotating vanes, counter-rotating vanes, and Wheeler Wishbone VGs were used in the vicinity of the leading and trailing edge flap hinge lines. Principle test parameters were leading and trailing edge flap deflections, and location, size, spacing, and orientation for each VG type. Gurney flaps were also tested. Data gathered include balance force and moment data, surface pressures, and flow visualization for characterizing flow behavior and locating separation lines. Results were quite different for the two best flap configurations tested. All VG types tested showed improvement (up to 5%) in maneuver L/D with flaps at LE=20 degrees, TE=0 degrees. The same VGs degraded performance, in all but a few cases, with flaps at LE=15 degrees, TE=10 degrees.

Samuels, Jeff↗
DOE OSTI2024

Strategically Modified Ligand Incorporating Mixed Phosphonate and Carboxylate Groups to Enhance Performance in All-Iron Redox Flow Batteries

Iron redox flow batteries (Fe-RFBs) hold significant promise for achieving cost-effectiveness and utilizing abundant materials for stationary energy storage applications. Here, a design of a novel Fe complex utilizing a nitrogenous phosphonate/carboxylate mixed ligand, N,N-Bis(phosphonomethyl)glycine (BMPG), is presented to achieve high performance Fe anolyte. Compared to its all-phosphonate form, nitrilotri(methylphosphonic acid) (NTMPA), the new complex Fe(BPMG) 2 demonstrates a negatively shifted redox potential, resulting in ≈0.07 V (≈10%) increase in battery output voltage. Full battery testing paired with ferrocyanide catholyte demonstrates stable cycling (capacity degradation <0.0001%/cycle) over 730 consecutive charge/discharge cycles with Coulombic Efficiency of 100% at a current density of 20 mA cm -2 under near neutral pH (≈8). Of particular interest, density functional theory (DFT) studies and operando Raman measurements provide strong evidence supporting a molecular structure in BPMG, which reveals the mixed phosphonate/carboxylate groups in BPMG maintain the octahedral coordination of the Fe ion center with phosphonates exclusively, while leaving the carboxylate unbound for both Fe(II) and Fe(III) complexes. This structural similarity between BPMG-based Fe(II) and Fe(III) complexes effectively mitigates the slow redox reaction kinetics observed in Fe(NTMPA) 2 anolyte, where significant ligand reorientation occurs between Fe(II) and Fe(III) complexes.

25 ENERGY STORAGE↗
DOE OSTI2021

An ultrathin solid-state electrolyte film coated on LiNi 0.8 Co 0.1 Mn 0.1 O 2 electrode surface for enhanced performance of lithium-ion batteries

We report layered Ni-rich oxide is a promising cathode material for lithium-ion batteries (LIBs) of high energy density, yet its poor electrochemical stability induced by electrode-electrolyte interfacial degradation has still needed to be addressed. Surface coating is one of the powerful techniques to tackle this issue, nevertheless, it has been extensively used on particle but not electrode regarding a larger area of protection. Herein, we have covered a nano-scaled layer of lithium phosphorus oxynitride (LiPON) on the electrode level of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM) surface and found lower impedance, longer cycle life, and better safety for treated battery. Most notably, such an NCM-LiPON based 1.3 Ah pouch cell delivers an energy density of 364.4 Wh kg -1 (based on positive and negative materials), along with the retention of 80.0% over 745 cycles at 0.5 C-rate, which is 1.3 times longer than the bare one. This results from modification of both superficial cathode-electrolyte interphase (CEI) and structure stabilization of general particle surface, therefore, role of conformal coating upon electrode surface should be highlighted.

36 MATERIALS SCIENCE↗