SEARCH · Search NASA

Results for “Periodic Heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Time-resolved spectrophotometry of the emission lines in the galactic X-ray source H2252-035

The galactic X-ray source H2252-035 has been the object of a concentrated observational effort, since Griffiths et al. (1980) have identified it with a cataclysmic variable-like spectrum. Since the observed 859 s periodicity corresponds to the beat frequency between the X-ray and orbital periods, it has been interpreted as related to a reprocessing of the X-ray flux into optical emission in some region of the system which is rotating with the orbital period and heated by beamed X-ray emission from the compact star. In connection with the present investigation, H2252-035 has been observed with a 120 inch (3 m) telescope and image dissector scanner on 1980 September 9/10 and on 1981 September 20/21. At a time resolution of approximately 2 minutes, four bright emission lines showed short time-scale flickering and a pronounced orbital period variation in phase with the continuum modulation. A two-component model for the line emission region is proposed.

Clarke, J. T.↗

NASA NTRS2007

Lunar Return Reentry Thermal Analysis of a Generic Crew Exploration Vehicle Wall Structures

Thermostructural analysis was performed on generic crew exploration vehicle (GCEV) heat shielded wall structures subjected to reentry heating rates based on five potential lunar return reentry trajectories. The GCEV windward outer wall is fabricated with a graphite/epoxy composite honeycomb sandwich panel and the inner wall with an aluminum honeycomb sandwich panel. The outer wall is protected with an ablative Avcoat-5026-39H/CG thermal protection system (TPS). A virtual ablation method (a graphical approximation) developed earlier was further extended, and was used to estimate the ablation periods, ablation heat loads, and the TPS recession layer depths. It was found that up to 83 95 percent of the total reentry heat load was dissipated in the TPS ablation process, leaving a small amount (3-15 percent) of the remaining total reentry heat load to heat the virgin TPS and maintain the TPS surface at the ablation temperature, 1,200 F. The GCEV stagnation point TPS recession layer depths were estimated to be in the range of 0.280-0.910 in, and the allowable minimum stagnation point TPS thicknesses that could maintain the substructural composite sandwich wall at the limit temperature of 300 F were found to be in the range of 0.767-1.538 in. Based on results from the present analyses, the lunar return abort ballistic reentry was found to be quite attractive because it required less TPS weight than the lunar return direct, the lunar return skipping, or the low Earth orbit guided reentry, and only 11.6 percent more TPS weight than the low Earth orbit ballistic reentry that will encounter a considerable weight penalty to obtain the Earth orbit. The analysis also showed that the TPS weight required for the lunar return skipping reentry was much more than the TPS weight necessary for any of the other reentry trajectories considered.

Ko, William L.↗

NASA NTRS2021

Pyrolysis Rate and Yield Strength Reduction Incarbon Fiber and Glass Fiber Composites Underreentry Heating Conditions

The behavior of composite materials, specifically carbon fiber reinforced plastic (CFRP) and glass fiber reinforced plastic (GFRP), under reentry conditions poses a problem for space debris reentry risk modeling. Since these materials pyrolyze rather than melt and their different components demise at different rates, modeling their destruction to determine ground impact risk is complex. Modern spacecraft are using these materials in ever-greater quantities owing to their superior strength-to-weight characteristics, and this has required that the orbital debris community improve its understanding of how these materials demise on reentry. The NASA Orbital Debris Program Office undertook an extensive test campaign to better understand the rate at which several types of GFRP and CFRP materials pyrolyze under reentry heating conditions and how that pyrolysis affects the ultimate strength of the material. GFRP with a polyester resin (G10/FR-4) and CFRP with epoxy, cyanate ester, vinyl ester, and phenolic resins were tested. The test campaign was carried out at the Inductively Coupled Plasma (ICP) Torch Facility at the University of Texas at Austin. Because the ICP facility operates in a shirt-sleeve environment, test samples can be changed within seconds or minutes, allowing many samples to be tested in a short period. Two heat flux rates, 20 W/m2 and 30W/m2, and two oxygen concentration conditions, 0% and 2% of atmospheric, were applied to all five types of material. To measure both the char rate and the effect of pyrolysis on the ultimate material strength, two types of test were carried out for each material: a char rate test on a ~10 mm thick sample of material and an in-situ bending stress test of a ~2 mm thick sample of material. Measurements of the char rate showed very similar average pyrolysis front velocity in epoxy resin CFRP as in G10 at 3.6 mm/min and 3.4 mm/min, respectively. However, the total mass loss rate in theG10 was nearly double that of the CFRP at 3.8 g/min and 2.2 g/min, respectively. This result represented a slow ablation rate of carbon fibers in the CFRP at the temperatures encountered in low Earth orbit reentry and a comparatively rapid removal of the glass fibers in G10 due to melting and spallation. Pyrolysis front velocity was more significantly affected by the type of plastic than the type of fiber, with the cyanate ester CFRP samples displaying an average pyrolysis front velocity of only 1.9 mm/min. Similarly, the effect of thermal exposure on the ultimate strength of the material depended heavily on the type of plastic and very little on the type of fiber in the material. Epoxy, vinyl ester, and polyester resins all behaved very similarly, with complete structural failure at between 400 J/g and 600 J/g of specific absorbed heat. Phenolic and cyanate ester resins, on the other hand, displayed a change in structural properties that was only barely measurable with the current apparatus even after the maximum exposure time tested. These data are being incorporated into a numerical model of the ablation and demise of composite materials that will be used to more accurately calculate the ground casualty risk of future spacecraft.

Benton R. Greene↗

NASA NTRS1985

Instability of time-periodic flows

The instabilities of some spatially and/or time-periodic flows are discussed, in particular, flows with curved streamlines which can support Taylor-Gortler vortices are described in detail. The simplest flow where this type of instability can occur is that due to the torsional oscillations of an infinitely long circular cylinder. For more complicated spatially varying time-periodic flows, a similar type of instability can occur and is spatially localized near the most unstable positions. When nonlinear effects are considered it is found that the instability modifies the steady streaming boundary layer induced by the oscillatory motion. It is shown that a rapidly rotating cylinder in a uniform flow is susceptible to a related type of instability; the appropriate stability equations are shown to be identical to those which govern the instability of a boussinesq fluid of Prandtl number unity heated time periodically from below.

Hall, P.↗

NASA NTRS1987

Instability of time-periodic flows

The instabilities of some spatially and/or time-periodic flows are discussed, in particular, flows with curved streamlines which can support Taylor-Gortler vortices are described in detail. The simplest flow where this type of instability can occur is that due to the torsional oscillations of an infinitely long circular cylinder. For more complicated spatially varying time-periodic flows, a similar type of instability can occur and is spatially localized near the most unstable positions. When nonlinear effects are considered it is found that the instability modifies the steady streaming boundary layer induced by the oscillatory motion. It is shown that a rapidly rotating cylinder in a uniform flow is susceptible to a related type of instability; the appropriate stability equations are shown to be identical to those which govern the instability of a Boussinesq fluid of Prandtl number unity heated time periodically from below.

Hall, Philip↗

NASA NTRS1975

Metabolism and heat dissipation during Apollo EVA periods

The extravehicular activity life support equipment, suit temperature control, metabolic rate measurement methods, and energy production are discussed. The Apollo crewmen were able to perform planned extravehicular activities and to extend them to the maximum time allowable without medical problems. The metabolic rates experienced during the lunar surface extravehicular activities were lower than conservative premission estimates. A manually controlled liquid cooling garment was effectively used to minimize fatigue and water loss from sweating during lunar surface extravehicular activities. Gas cooling was adequate during the short zero-g extravehicular activities performed from the command module. The prediction of EVA workloads became more reliable as inflight data was accumulated. The prediction of the average metabolic cost of an EVA was more reliable than the cost of an individual short-term task.

J.M. Waligora↗

NASA NTRS1984

Analysis of the Viking Lander 1 surface wind vector for sols 45 to 375

The Viking Lander 1 wind sensor data during the period between sols 45 and 375 were corrected. During this period, the heating element of the quadrant sensor which provided the primary signal used for determining wind direction had failed, but both hot film wind sensors were functioning normally. The wind speed and direction corrections are explained.

Leovy, C. B.↗

NASA NTRS1985

Monogroove heat pipe design: Insulated liquid channel with bridging wick

A screen mesh artery supported concentrically within the evaporator section of a heat pipe liquid channel retains liquid in the channel. Continued and uniform liquid feed to the heat pipe evaporation section (20) during periods of excessive heat transfer is assured. The overall design provides high evaporation and condensation film coefficients for the working fluid by means of the circumferential grooves in the walls of the vapor channel, while not interfering with the overall heat transport capability of the axial groove. The design has particular utility in zero-g environments.

Alario, J. P.↗

NASA NTRS1984

Results from the transition region camera

Three series of high resolution ultra-violet pictures of the sun have been obtained during the three flights of rocket experiment T.R.C. Transition Region Camera) which took place on 3 July 1979, 23 September 1980 and 13 July 1982. These pictures reveal many structures in Ly alpha and ultraviolet continua at 160 nm and 220 nm. The scientific objectives, instrumentation, flight conditions and campaigns of simultaneous observations are described. The contribution of T.R.C. to solar physics is discussed in the framework of chromospheric multicomponent models, magnetic flux tubes, local heating and periodic structures in the chromosphere.

Foing, B. H.↗

NASA NTRS1985

Active control of compressible flows on a curved surface

The effect of localized, time periodic surface heating and cooling over a curved surface is studied. This is a mechanism for the active control of unstable disturbances by phase cancellation and reinforcement. It is shown that the pressure gradient induced by the curvature significantly enhances the effectiveness of this form of active control. In particular, by appropriate choice of phase, active surface heating can completely stabilize and unstable wave.

Maestrello, L.↗

NASA NTRS1985

Wave phenomena in a high Reynolds number compressible boundary layer

Growth of unstable disturbances in a high Reynolds number compressible boundary layer is numerically simulated. Localized periodic surface heating and cooling as a means of active control of these disturbances is studied. It is shown that compressibility in itself stabilizes the flow but at a lower Mach number, significant nonlinear distortions are produced. Phase cancellation is shown to be an effective mechanism for active boundary layer control.

Bayliss, A.↗

NASA NTRS1985

Active control of compressible flows on a curved surface

Maestrello, L.↗

NASA NTRS1991

Aerothermodynamic heating environment and thermal protection materials comparison for manned Mars-earth return vehicles

The aerothermodynamic environment during the earth return portion of a specific manned Mars mission is studied. Particular attention is given to the earlier smaller crew return capsule and its thermal protection system requirements. Data are presented on the stagnation region of a generic Mars return capsule. Insulation material thicknesses required to maintain allowable structural temperatures throughout a prolonged heat soak period are estimated.

Henline, William D.↗

NASA NTRS1992

Customized ATP towpreg

Automated tow placement (ATP) utilizes robotic technology to lay down adjacent polymer-matrix-impregnated carbon fiber tows on a tool surface. Consolidation and cure during ATP requires that void elimination and polymer matrix adhesion be accomplished in the short period of heating and pressure rolling that follows towpreg ribbon placement from the robot head to the tool. This study examined the key towpreg ribbon properties and dimensions which play a significant role in ATP. Analysis of the heat transfer process window indicates that adequate heating can be achieved at lay down rates as high as 1 m/sec. While heat transfer did not appear to be the limiting factor, resin flow and fiber movement into tow lap gaps could be. Accordingly, consideration was given to towpreg ribbon having uniform yet non-rectangular cross sections. Dimensional integrity of the towpreg ribbon combined with customized ribbon architecture offer great promise for processing advances in ATP of high performance composites.

Sandusky, Donald A.↗

NASA NTRS1993

Theoretical and Experimental Investigations on Droplet Evaporation and Droplet Ignition at High Pressures

The evaporation of fuel droplets under high ambient pressure and temperature in normal gravity and microgravity has been investigated experimentally. For subcritical ambient conditions, droplet evaporation after a heat-up period follows the d(exp 2)-law. For all data the evaporation constant increases as the ambient temperature increases. At identical ambient conditions the evaporation constant under microgravity is smaller compared to normal gravity. This effect can first be observed at 1 bar and increases with ambient pressure. Preliminary experiments on ignition delay for self-igniting fuel droplets have been performed. Above a 1 s delay time, at identical ambient conditions, significant differences in the results of the normal and microgravity data are observed. Self-ignition occurs within different temperature ranges due to the influence of gravity. The time dependent behavior of the droplet is examined theoretically. In the calculations two different approaches for the gas phase are applied. In the first approach the conditions at the interface are given using a quasi steady theory approximation. The second approach uses a set of time dependent governing equations for the gas phase which are then evaluated. In comparison, the second model shows a better agreement with the drop tower experiments. In both cases a time dependent gasification rate is observed.

Ristau, R.↗

NASA NTRS1995

Low-frequency oscillations in radiative-convective systems. Part 2: An idealized model

A simple model is used to examine the hypothesis that nonlinear interactions among atmospheric radiation, cumulus convection, and the surface moisture flux can result in a stationary, low-frequency (30-60 day period) oscillating heat source in the tropical atmosphere. The model produces low-frequency oscillations of temperature, moisture, and precipitation. The mechanism that produces these oscillations is identified through analyses of the model and its results. The relevance of this mechanism to understand the observed Madden-Julian oscillation in the tropical atmosphere over the Indian and western Pacific Oceans is discussed.

Hu, QI↗

NASA NTRS2017

PIPER Continuous Adiabatic Demagnetization Refrigerator

We report upon the development and testing of a 4-stage adiabatic demagnetization refrigerator (ADR) capable of continuous cooling at 0.100 Kelvin. This cooler is being built to cool the detector array aboard NASA's Primordial Inflation Polarization Explorer (PIPER) observatory. The goal of this balloon mission is to measure the primordial gravitational waves that should exist if the theory of cosmological inflation is correct. At altitude, the ADR will hold the array of transition-edge sensors at 100 mK continuously while periodically rejecting heat to a 1.2 K pumped helium bath. During testing on ground, the array is held at the same temperature but heat is rejected to a 4.2 K helium bath indicating the flexibility in this coolers design.

Magnetic Cooling Sub-Kelvin ADR↗

NASA NTRS1985

Numerical simulation of boundary layer excitation by surface heating/cooling

The concept of active control of growing disturbances in an unstable compressible flow by using time periodic, localized surface heating is studied numerically. The simulations are calculated by a fourth-order accurate solution of the compressible, laminar Navier-Stokes equations. Fourth-order accuracy is particularly important for this problem because the solution must be computed over many wavelengths. The numerical results demonstrate the growth of an initially small fluctuation into the nonlinear regime where a local breakdown into smaller scale disturbances can be observed. It is shown that periodic surface heating over a small strip can reduce the level of the fluctuation provided that the phase of the heating current is properly chosen.

Bayliss, A.↗