SEARCH · Search NASA
Results for “Quantum Dots”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flexible and efficient perovskite quantum dot solar cells via hybrid interfacial architecture
All-inorganic CsPbI 3 perovskite quantum dots have received substantial research interest for photovoltaic applications because of higher efficiency compared to solar cells using other quantum dots materials and the various exciting properties that perovskites have to offer. These quantum dot devices also exhibit good mechanical stability amongst various thin-film photovoltaic technologies. We demonstrate higher mechanical endurance of quantum dot films compared to bulk thin film and highlight the importance of further research on high-performance and flexible optoelectronic devices using nanoscale grains as an advantage. Specifically, we develop a hybrid interfacial architecture consisting of CsPbI 3 quantum dot/PCBM heterojunction, enabling an energy cascade for efficient charge transfer and mechanical adhesion. The champion CsPbI3 quantum dot solar cell has an efficiency of 15.1% (stabilized power output of 14.61%), which is among the highest report to date. Building on this strategy, we further demonstrate a highest efficiency of 12.3% in flexible quantum dot photovoltaics.
Vertical Architecture Solution-Processed Quantum Dot Photodetectors with Amorphous Selenium Hole Transport Layer
Colloidal quantum dots (CQDs) provide wide spectral tunability and high absorption coefficients owing to quantum confinement and large oscillator strengths, which along with solution processability, allow a facile, low-cost, and room-temperature deposition technique for the fabrication of photonic devices. However, many solution-processed CQD photodetector devices demonstrate low specific-detectivity and slow temporal response. To achieve improved photodetector characteristics, limiting carrier recombination and enhancing photogenerated carrier separation are crucial. In this study, we develop and present an alternate vertical-stack photodetector wherein we use a solution-processed quantum dot photoconversion layer coupled to an amorphous selenium (a-Se) wide-bandgap charge transport layer that is capable of exhibiting single-carrier hole impact ionization and is compatible with active-matrix readout circuitry. This a-Se chalcogenide transport layer enables the fabrication of high-performance and reliable solution-processed quantum dot photodetectors, with enhanced charge extraction capabilities, high specific detectivity (D* ~ 0.5–5 × 10 12 Jones), fast 3 dB electrical bandwidth (3 dB BW ~ 22 MHz), low dark current density (J D ~ 5–10 pA/cm 2 ), low noise current (i n ~ 20–25 fW/Hz 1/2 ), and high linear dynamic range (LDR ~130–150 dB) across the measured visible electromagnetic spectrum (~405–656 nm).
Ultrafast electron dynamics of graphene quantum dots: High harmonic generation
We study theoretically nonlinear optical properties of graphene quantum dots placed in a field of a short and strong linearly polarized optical pulse. We address the problem of high harmonic generation in quantum dots and how such nonlinear effect is affected by dephasing processes in a quantum dot. The dephasing makes the ultrafast electron dynamics more irreversible with a large residual population of the excited quantum dot levels. In relation to the high-harmonic spectrum, with increasing the dephasing time, the intensities of the low-frequency harmonics increase while the cutoff energy decreases. The dependence of the cutoff energy on the amplitude of the optical pulse is also sensitive to the frequency of the pulse. When the frequency of the optical pulse is much less than the quantum dot band gap, this dependence is almost linear, but when the frequency of the pulse is comparable to the band gap, the cutoff energy shows saturation behavior at large field amplitude, >0.4 V/Å.
The Effect of Monomer Size on Fusion and Coupling in Colloidal Quantum Dot Molecules
The fusion step in the formation of colloidal quantum dot molecules, constructed from two core/shell quantum dots, dictates the coupling strength and hence their properties and enriched functionalities compared to monomers. Herein, studying the monomer size effect on fusion and coupling, we observe a linear relation of the fusion temperature with the inverse nanocrystal radius. This trend, similar to that in nanocrystal melting, emphasizes the role of the surface energy. The suggested fusion mechanism involves intraparticle ripening where atoms diffuse to the reactive connecting neck region. Moreover, the effect of monomer size and neck filling on the degree of electronic coupling is studied by combined atomistic-pseudopotential calculations and optical measurements, uncovering strong coupling effects in small QD dimers, leading to significant optical changes. Understanding and controlling the fusion and hence coupling effect allows tailoring the optical properties of these nanoscale structures, with potential applications in photonic and quantum technologies.
Adding GaAs Monolayers to InAs Quantum-Dot Lasers on (001) InP
In a modification of the basic configuration of InAs quantum-dot semiconductor lasers on (001)lnP substrate, a thin layer (typically 1 to 2 monolayer thick) of GaAs is incorporated into the active region. This modification enhances laser performance: In particular, whereas it has been necessary to cool the unmodified devices to temperatures of about 80 K in order to obtain lasing at long wavelengths, the modified devices can lase at wavelengths of about 1.7 microns or more near room temperature. InAs quantum dots self-assemble, as a consequence of the lattice mismatch, during epitaxial deposition of InAs on ln0.53Ga0.47As/lnP. In the unmodified devices, the quantum dots as thus formed are typically nonuniform in size. Strainenergy relaxation in very large quantum dots can lead to poor laser performance, especially at wavelengths near 2 microns, for which large quantum dots are needed. In the modified devices, the thin layers of GaAs added to the active regions constitute potential-energy barriers that electrons can only penetrate by quantum tunneling and thus reduce the hot carrier effects. Also, the insertion of thin GaAs layer is shown to reduce the degree of nonuniformity of sizes of the quantum dots. In the fabrication of a batch of modified InAs quantum-dot lasers, the thin additional layer of GaAs is deposited as an interfacial layer in an InGaAs quantum well on (001) InP substrate. The device as described thus far is sandwiched between InGaAsPy waveguide layers, then further sandwiched between InP cladding layers, then further sandwiched between heavily Zn-doped (p-type) InGaAs contact layer.
Quantum Computation Using Optically Coupled Quantum Dot Arrays
A solid state model for quantum computation has potential advantages in terms of the ease of fabrication, characterization, and integration. The fundamental requirements for a quantum computer involve the realization of basic processing units (qubits), and a scheme for controlled switching and coupling among the qubits, which enables one to perform controlled operations on qubits. We propose a model for quantum computation based on optically coupled quantum dot arrays, which is computationally similar to the atomic model proposed by Cirac and Zoller. In this model, individual qubits are comprised of two coupled quantum dots, and an array of these basic units is placed in an optical cavity. Switching among the states of the individual units is done by controlled laser pulses via near field interaction using the NSOM technology. Controlled rotations involving two or more qubits are performed via common cavity mode photon. We have calculated critical times, including the spontaneous emission and switching times, and show that they are comparable to the best times projected for other proposed models of quantum computation. We have also shown the feasibility of accessing individual quantum dots using the NSOM technology by calculating the photon density at the tip, and estimating the power necessary to perform the basic controlled operations. We are currently in the process of estimating the decoherence times for this system; however, we have formulated initial arguments which seem to indicate that the decoherence times will be comparable, if not longer, than many other proposed models.
Photoluminescence Enhancement, Blinking Suppression, and Improved Biexciton Quantum Yield of Single Quantum Dots in Zero Mode Waveguides
The capability of quantum dots to generate both single and multiexcitons can be harnessed for a wide variety of applications, including those that require high optical gain. Here, we use time-correlated photoluminescence (PL) spectroscopy to demonstrate that the isolation of single CdSeTe/ZnS core–shell, nanocrystal quantum dots (QDs) in Zero Mode Waveguides (ZMWs) leads to a significant modification in PL intensity, blinking dynamics, and biexciton behavior. QDs in aluminum ZMWs (AlZMWs) exhibited a 15-fold increase in biexciton emission, indicating a preferential enhancement of the biexciton radiative decay rate as compared to the single exciton rate. The increase in biexciton behavior was accompanied by a decrease in blinking events due to a shortening in the dark state residence time. These results indicate that plasmon mediated enhanced decay rates of QDs in AlZMWs lead to substantial changes in the photophysical properties of single quantum dots, including an increase in biexciton behavior.
Prospects and challenges of colloidal quantum dot laser diodes
Colloidal quantum dots (QDs) combine the superior light-emission characteristics of quantum-confined semiconductors with the chemical flexibility of molecular systems. We find that these properties could, in principle, enable solution-processable laser diodes with an ultrawide range of accessible colours. However, the realization of such devices has been hampered by fast optical gain decay due to non-radiative Auger recombination and poor stability of QD solids at the high current densities required for the lasing regime. Recently, these problems have been resolved, which resulted in the development of electrically pumped optical gain devices operating at ultrahigh current densities of around 1,000 A cm -2 . The next step is the realization of a QD laser diode (QLD). Here we assess the status of the QD lasing field, examine the remaining challenges on the path to a QLD and discuss practical strategies for attaining electrically pumped QD lasing.
Modeling lithographic quantum dots and donors for quantum computation and simulation
Explore the source record for details and available documents.
Quantum Dot Solar Cells
We have been investigating the synthesis of quantum dots of CdSe, CuInS2, and CuInSe2 for use in an intermediate bandgap solar cell. We have prepared a variety of quantum dots using the typical organometallic synthesis routes pioneered by Bawendi, et. al., in the early 1990's. However, unlike previous work in this area we have also utilized single-source precursor molecules in the synthesis process. We will present XRD, TEM, SEM and EDS characterization of our initial attempts at fabricating these quantum dots. Investigation of the size distributions of these nanoparticles via laser light scattering and scanning electron microscopy will be presented. Theoretical estimates on appropriate quantum dot composition, size, and inter-dot spacing along with potential scenarios for solar cell fabrication will be discussed.
Thermal tolerance of perovskite quantum dots dependent on A-site cation and surface ligand
A detailed picture of temperature dependent behavior of Cs x FA 1-x PbI 3 perovskite quantum dots across the composition range is constructed by performing in situ optical spectroscopic and structural measurements, supported by theoretical calculations that focus on the relation between A-site chemical composition and surface ligand binding. The thermal degradation mechanism depends not only on the exact chemical composition, but also on the ligand binding energy. The thermal degradation of Cs-rich perovskite quantum dots is induced by a phase transition from black γ-phase to yellow δ-phase, while FA-rich perovskite quantum dots with higher ligand binding energy directly decompose into PbI 2 . Quantum dot growth to form large bulk size grain is observed for all Cs x FA 1-x PbI 3 perovskite quantum dots at elevated temperatures. In addition, FA-rich quantum dots possess stronger electron-longitudinal optical phonon coupling, suggesting that photogenerated excitons in FA-rich quantum dots have higher probability to be dissociated by phonon scattering compared to Cs-rich quantum dots.
From Inside Out: How the Buried Interface, Shell Defects, and Surface Chemistry Conspire to Determine Optical Performance in Nonblinking Giant Quantum Dots
“Giant” or core/thick‐shell quantum dots (gQDs) are an important class of solid‐state quantum emitter characterized by strongly suppressed blinking and photobleaching under ambient conditions, and reduced nonradiative Auger processes. Together, these qualities provide distinguishing and useful functionality as single‐ and ensemble‐photon sources. For many applications, operation at elevated temperatures and under intense photon flux is desired, but performance is strongly dependent on the synthetic method employed for thick‐shell growth. Here, a comprehensive analysis of gQD structural properties “from the inside out” as a function of shell‐growth method is reported: successive ionic layer adsorption and reaction (SILAR) and high‐temperature continuous injection (HT‐CI), or sequential combinations of the two. Key correlations across synthesis methods, structural features (interfacial alloying, stacking‐fault density and surface‐ligand identity), and performance metrics (quantum yield, single‐gQD photoluminescence under thermal/photo stress, charging behavior and quantum‐optical properties) are identified. Surprisingly, it is found that interfacial alloying is the strongest indicator of gQD stability under stress, but this parameter is not the determining factor for Auger suppression. Furthermore, quantum yield is strongly influenced by surface chemistry and can approach unity even in the case of high shell‐defect density, while introduction of zinc‐blende stacking faults increases the likelihood that a gQD exhibits charged‐state emission.
Polariton-assisted incoherent to coherent excitation energy transfer between colloidal nanocrystal quantum dots
Here, we explore the dynamics of energy transfer between two nanocrystal quantum dots placed within an optical microcavity. By adjusting the coupling strength between the cavity photon mode and the quantum dots, we have the capacity to fine-tune the effective coupling between the donor and acceptor. Introducing a non-adiabatic parameter, γ, governed by the coupling to the cavity mode, we demonstrate the system’s capability to shift from the overdamped Förster regime (γ $\ll$ 1) to an underdamped coherent regime (γ $\gg$ 1). In the latter regime, characterized by swift energy transfer rates, the dynamics are influenced by decoherence time. To illustrate this, we study the exciton energy transfer dynamics between two closely positioned CdSe/CdS core/shell quantum dots with sizes and separations relevant to experimental conditions. Employing an atomistic approach, we calculate the excitonic level arrangement, exciton–phonon interactions, and transition dipole moments of the quantum dots within the microcavity. These parameters are then utilized to define a model Hamiltonian. Subsequently, we apply a generalized non-Markovian quantum Redfield equation to delineate the dynamics within the polaritonic framework.
Dangling Bonds as Possible Contributors to Charge Noise in Silicon and Silicon–Germanium Quantum Dot Qubits
Spin qubits based on Si and Si 1–x Ge x quantum dot architectures exhibit among the best coherence times of competing quantum computing technologies, yet they still suffer from charge noise that limit their qubit gate fidelities. Identifying the origins of these charge fluctuations is therefore a critical step toward improving Si quantum-dot-based qubits. Here, we use hybrid functional calculations to investigate possible atomistic sources of charge noise, focusing on charge trapping at Si and Ge dangling bonds (DBs). We evaluate the role of global and local environment in the defect levels associated with DBs in Si, Ge, and Si 1–x Ge x alloys, and consider their trapping and excitation energies within the framework of configuration coordinate diagrams. We additionally consider the influence of strain and oxidation in charge-trapping energetics by analyzing Si and GeSi DBs in SiO 2 and strained Si layers in typical Si 1–x Ge x quantum dot heterostructures. Our results identify that Ge dangling bonds are more problematic charge-trapping centers both in typical Si 1–x Ge x alloys and associated oxidation layers, and they may be exacerbated by compositional inhomogeneities. In conclusion, these results suggest the importance of alloy homogeneity and possible passivation schemes for DBs in Si-based quantum dot qubits and are of general relevance to mitigating possible trap levels in other Si, Ge, and Si 1–x Ge x -based metal-oxide-semiconductor stacks and related devices.
Long-Wavelength Infrared (LWIR) Quantum Dot Infrared Photodetector (QDIP) Focal Plane Array
We have exploited the artificial atomlike properties of epitaxially self-assembled quantum dots for the development of high operating temperature long wavelength infrared (LWIR) focal plane arrays. Quantum dots are nanometer-scale islands that form spontaneously on a semiconductor substrate due to lattice mismatch. QDIPs are expected to outperform quantum well infrared detectors (QWIPs) and are expected to offer significant advantages over II-VI material based focal plane arrays. QDIPs are fabricated using robust wide bandgap III-V materials which are well suited to the production of highly uniform LWIR arrays. We have used molecular beam epitaxy (MBE) technology to grow multi-layer LWIR quantum dot structures based on the InAs/InGaAs/GaAs material system. JPL is building on its significant QWIP experience and is basically building a Dot-in-the-Well (DWELL) device design by embedding InAs quantum dots in a QWIP structure. This hybrid quantum dot/quantum well device offers additional control in wavelength tuning via control of dot-size and/or quantum well sizes. In addition the quantum wells can trap electrons and aide in ground state refilling. Recent measurements have shown a 10 times higher photoconductive gain than the typical QWIP device, which indirectly confirms the lower relaxation rate of excited electrons (photon bottleneck) in QDPs. Subsequent material and device improvements have demonstrated an absorption quantum efficiency (QE) of approx. 3%. Dot-in-the-well (DWELL) QDIPs were also experimentally shown to absorb both 45 deg. and normally incident light. Thus we have employed a reflection grating structure to further enhance the quantum efficiency. JPL has demonstrated wavelength control by progressively growing material and fabricating devices structures that have continuously increased in LWIR response. The most recent devices exhibit peak responsivity out to 8.1 microns. Peak detectivity of the 8.1 micrometer devices has reached approx. 1 x 10(exp 10) Jones at 77 K. Furthermore, we have fabricated the first long-wavelength 640x512 pixels QDP focal plane array. This QDIP focal plane may has produced excellent infrared imagery with noise equivalent temperature difference of 40 mK at 60K operating temperature. In addition, we have managed to increase the quantum efficiency of these devices from 0.1% (according to the data published in literature) to 20% in discrete devices. This is a factor of 200 increase in quantum efficiency. With these excellent results, for the first time QDIP performance has surpassed the QWIP performance. Our goal is to operate these long-wavelength detectors at much higher operating temperature than 77K which can be passively achieved in space. This will be a huge leap in high performance infrared detectors specifically applicable to space science instruments.
Tuning the Dimensionality of Excitons in Colloidal Quantum Dot Molecules
Electrically coupled quantum dots (QDs) can support unique optoelectronic properties arising from the superposition of single-particle excited states. Experimental methods for integrating colloidal QDs within the same nano-object, however, have remained elusive to the rational design. Here, we demonstrate a chemical strategy that allows for the assembling of colloidal QDs into coupled composites, where proximal interactions give rise to unique optoelectronic behavior. The assembly method employing “adhesive” surfactants was used to fabricate both homogeneous (e.g., CdS–CdS, PbS–PbS, CdSe–CdSe) and heterogeneous (e.g., PbS–CdS, CdS–CdSe) nanoparticle assemblies, exhibiting quasi-one-dimensional exciton fine structure. In addition, tunable mixing of single-particle exciton states was achieved for dimer-like assemblies of CdSe/CdS core–shell nanocrystals. The nanoparticle assembly mechanism was explained within the viscoelastic interaction theory adapted for molten-surface colloids. Furthermore, we expect that the present work will provide the synthetic and theoretical foundation needed for building assemblies of many inorganic nanocrystals.
Diabatic error and propagation of Majorana zero modes in interacting quantum dots systems
Motivated by recent experimental progress in realizing Majorana zero modes (MZMs) using quantum dot systems, we investigate the diabatic errors associated with the movement of those MZMs. The movement is achieved by tuning time-dependent gate potentials applied to individual quantum dots, effectively creating a moving potential wall. To probe the optimized movement of MZMs, we calculate the experimentally accessible time-dependent fidelity and local density-of-states using many-body time-dependent numerical methods. Furthermore, our analysis reveals that an optimal potential wall height is crucial to preserve the well-localized nature of the MZM during its movement. Moreover, we analyze diabatic errors in realistic quantum-dot systems, incorporating the effects of repulsive Coulomb interactions and disorder in both hopping and pairing terms. Additionally, we provide a comparative study of diabatic errors arising from the simultaneous versus sequential tuning of multiple gates during the MZMs movement. Finally, we estimate the timescale required for MZM transfer in a six-quantum-dot system, demonstrating that MZM movement is feasible and can be completed well within the qubit's operational lifetime in practical quantum-dot setups.