Search NASA⌕ Search

SEARCH · Search NASA

Results for “REACTION JET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Appendix A: Proposed statement of work, 1994

This NRA effort is devoted to developing new techniques and methodologies which utilize and/or provide support to Integrated Vehicle Health Management (IVHM) concepts and techniques, modern design processes, and open architectures to realize an avionics system architecture that relieves the flight control system (FCS) of the requirement of maintaining intimate knowledge and control of the vehicle subsystems (for instance, the reaction control system (RCS)). The benefit of this architecture is that future upgrades and enhancements to the system(s) or to individual components within the system(s) are greatly simplified. This approach also allows a much more straightforward treatment of failure analysis, system diagnosis, and the design of fault containment domains. This NRA effort is also devoted to realizing capabilities to provide an available avionics system (and subsystem(s)) at minimum operational cost. This thrust provides a direct benefit to NASA in that it seeks to accelerate the design cycle to allow state of the art components and designs to actually appear in the fielded system rather than merely in the initial design. To achieve this, this effort is intended to benefit from efforts already underway at Lockheed and other major contractors. For instance, Lockheed Sanders is currently engaged in a major DoD funded development program which has the goal of cutting design cycle time of high performance electronics by a factor of four while simultaneously improving quality also by a factor of four. The early work on this program was used to enable the rapid prototyping of the Reaction Jet Drive Controller which was accomplished in 1993. Similarly, maximum leverage will be derived from recent NASA and DoD efforts to increase the content of high quality commercial grade electronic components in systems for aerospace applications. Both of these goals result in a system with enhanced cost effectiveness, increased reliability, and greatly increased performance compared to a system developed using a more conventional approach.

Source record↗
NASA NTRS1993

Inertial-space disturbance rejection for space-based manipulators

The implementation of a disturbance rejection controller for a 6-DOF PUMA manipulator mounted on a 3-DOF platform was described. A control algorithm is designed to track the desired position and attitude of the end-effector in inertial space, subject to unknown disturbances in the platform axes. Experimental results are presented for step, sinusoidal, and random disturbances in the platform rotational axis and in the neighborhood of kinematic singularities. Robotic manipulators were proposed as a means of reducing the amount of extra vehicular activity time required for space station assembly and maintenance. The proposed scenario involves a robotic manipulator attached to some mobile platform, such as a spacecraft, satellite, or the space station itself. Disturbances in the platform position and attitude may prevent the manipulator from successfully completing the task. The possibility of using the manipulator to compensate for platform disturbances was explored. The problem of controlling a robotic manipulator on a mobile platform has received considerable attention in the past few years. Joshi and Desrochers designed a nonlinear feedback control law to carry out tasks (with respect to the robot base frame) in the presence of roll, pitch and yaw disturbances in the platform axes. Dubowsky, Vance, and Torres proposed a time-optimal planning algorithm for a robotic manipulator mounted on a spacecraft, subject to saturation limits in the attitude control reaction jets. Papadopoulos and Dubowsky developed a general framework for analyzing the control of free-floating space manipulator systems. Most recently, Torres and Dubowsky have presented a technique called the enhanced disturbance map to find manipulator trajectories that reduce the effect of disturbances in the spacecraft position and attitude. One common assumption in the literature is that the disturbance signal is exactly known. If this is the case, then the end-effector location can be calculated without relying on direct end-point sensing. However, this assumption is invalid if there is a significant delay in the platform position and attitude measurements, or if the kinematics of the platform are not well known, or if the platform is a non-rigid structure. In the more likely case that only the nominal platform location and upper bound on the disturbance signal are known, direct end-point sensing is needed to measure the end-effector location.

Holt, Kevin↗
NASA NTRS1994

New technologies for space avionics

This report reviews a 1994 effort that continued 1993 investigations into issues associated with the definition of requirements, with the practice concurrent engineering and rapid prototyping in the context of the development of a prototyping of a next-generation reaction jet driver controller. This report discusses lessons learned, the testing of the current prototype, the details of the current design, and the nature and performance of a mathematical model of the life cycle of a pilot operated valve solenoid.

Aibel, David W.↗
NASA NTRS1996

Augmentation of Rocket Propulsion: Physical Limits

Rocket propulsion is not ideal when the propellant is not ejected at a unique velocity in an inertial frame. An ideal velocity distribution requires that the exhaust velocity vary linearly with the velocity of the vehicle in an inertial frame. It also requires that the velocity distribution variance as a thermodynamic quantity be minimized. A rocket vehicle with an inert propellant is not optimal, because it does not take advantage of the propellant mass for energy storage. Nor is it logical to provide another energy storage device in order to realize variable exhaust velocity, because it would have to be partly unfilled at the beginning of the mission. Performance is enhanced by pushing on the surrounding because it increases the reaction mass and decreases the reaction jet velocity. This decreases the fraction of the energy taken away by the propellant and increases the share taken by the payload. For an optimal model with the propellant used as fuel, the augmentation realized by pushing on air is greatest for vehicles with a low initial/final mass ratio. For a typical vehicle in the Earth's atmosphere, the augmentation is seen mainly at altitudes below about 80 km. When drag is taken into account, there is a well-defined optimum size for the air intake. Pushing on air has the potential to increase the performance of rockets which pass through the atmosphere. This is apart from benefits derived from "air breathing", or using the oxygen in the atmosphere to reduce the mass of an on-board oxidizer. Because of the potential of these measures, it is vital to model these effects more carefully and explore technology that may realize their advantages.

Taylor, Charles R.↗
NASA NTRS1961

Predicted Performance of On-Off Systems for Precise Satellite Attitude Control

An investigation has been made of the use of on-off reaction jets for precision attitude control of a satellite. Since a symmetrical vehicle is assumed, only single-axis control needs to be considered. The responses to initial disturbances and also limit-cycle characteristics for several systems have been evaluated. Calculated results indicate that realistic values of settling time and fuel consumption for the example considered can be obtained. The performance of a given system depends on the characteristics of the error detector used. In cases where the detector output was saturated for a relatively low error input, the settling time deteriorated when a lead network was used to provide damping. This deterioration could be eliminated if a separate rate signal to produce vehicle rate limiting were available. As an alternate approach, two systems were investigated which used a timed sequence of torques and could operate with a detector output of very small linear range. Although the performance of these systems was poorer than that of the lead network system without detector saturation, the performance was better than that of the lead network system with low values of detector saturation. The effects on limit-cycle characteristics of hysteresis, lead network constants, dead zone, and thrust time delays were also investigated.

Brown, Stuart C.↗
NASA NTRS1999

Implementation of Autonomous GPS Guidance and Control for Spacecraft Formation Flying

This paper presents the general relative orbit dynamics equations and GPS (Global Positioning System) orbit observational equations that have been developed for on-board control of spacecraft flying in formation. The approach to the implementation of the autonomous control for orbit acquisition and maintenance of spacecraft formation using GPS code pseudoranges are presented. As a practical application of the models and method provided in this paper, the orbit control of the Earth-Orbiter 1(EO-1) / Landsat 7 system has been designed, using the discrete-time linear optimal output feedback control. For the actuator of the on/off type reaction jets, the implementation problem of the pulse-amplitude modulation is also studied. Simulation results of autonomous orbit control and maintenance, for 3-dimensional initial orbit error, using optimal output feedback control are shown. These simulation results certified the feasibility of the implementation of the autonomous maintenance control for EO-1/Landsat 7 formation flying by means of the discrete-time linear optimal output feedback control.

Xing, Guang Q.↗
NASA NTRS1991

Handling Qualities Results of an Initial Geared Flap Tilt Wing Piloted Simulation

An exploratory simulation study of a novel approach to pitch control for a tilt wing aircraft was conducted in 1990 on the NASA-Ames Vertical Motion Simulator. The purpose of the study was to evaluate and compare the handling qualities of both a conventional and a geared flap tilt wing control configuration. The geared flap is an innovative control concept which has the potential for reducing or eliminating the horizontal pitch control tail rotor or reaction jets required by prior tilt wing designs. The handling qualities results of the geared flap control configuration are presented in this paper and compared to the conventional (programmed flap) tilt wing control configuration. This paper also describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, and the pilot evaluation tasks and procedures.

Guerrero, Lourdes M.↗
NASA NTRS2003

Using Bond Graphs for Articulated, Flexible Multi-bodies, Sensors, Actuators, and Controllers with Application to the International Space Station

Conceptually, modeling of flexible, multi-body systems involves a formulation as a set of time-dependent partial differential equations. However, for practical, engineering purposes, this modeling is usually done using the method of Finite Elements, which approximates the set of partial differential equations, thus generalizing the approach to all continuous media. This research investigates the links between the Bond Graph method and the classical methods used to develop system models and advocates the Bond Graph Methodology and current bond graph tools as alternate approaches that will lead to a quick and precise understanding of a flexible multi-body system under automatic control. For long endurance, complex spacecraft, because of articulation and mission evolution the model of the physical system may change frequently. So a method of automatic generation and regeneration of system models that does not lead to implicit equations, as does the Lagrange equation approach, is desirable. The bond graph method has been shown to be amenable to automatic generation of equations with appropriate consideration of causality. Indeed human-interactive software now exists that automatically generates both symbolic and numeric system models and evaluates causality as the user develops the model, e.g. the CAMP-G software package. In this paper the CAMP-G package is used to generate a bond graph model of the International Space Station (ISS) at an early stage in its assembly, Zvezda. The ISS is an ideal example because it is a collection of bodies that are articulated, many of which are highly flexible. Also many reaction jets are used to control translation and attitude, and many electric motors are used to articulate appendages, which consist of photovoltaic arrays and composite assemblies. The Zvezda bond graph model is compared to an existing model, which was generated by the NASA Johnson Space Center during the Verification and Analysis Cycle of Zvezda.

Montgomery, Raymond C.↗
NASA NTRS2005

MicroPPT-Based Secondary/Backup ACS for a 160-m, 450-kg Solar Sail Spacecraft

Solar sail tip-mounted, lightweight pulsed plasma thrusters (PPTs) are proposed for a secondary (or backup) attitude control system (ACS) of a 160-m, 450-kg solar sail spacecraft of the Solar Polar Imager (SPI) mission. A propellantless primary ACS of the SPI sailcraft employs trim control masses running along mast lanyards for pitch/yaw control together with roll stabilizer bars at the mast tips for quadrant tilt (roll) control. The robustness of such a propellantless primary ACS would be further enhanced by a secondary ACS utilizing tip-mounted, lightweight PPTs. The microPPT-based ACS is intended mainly for attitude recovery maneuvers from various off-nominal conditions that cannot be reliably handled by the propellantless primary ACS. However, it can also be employed for: i) the checkout or standby mode prior to and during sail deployment, ii) the post-deployment transition mode (prior to the propellantless primary ACS mode operation), iii) the solar sailing cruise mode of a trimmed sailcraft, and iv) the spin-stabilized, sun-pointing, safe mode. Although a conventional bus ACS is required for the SPI mission as the sail is jettisoned at the start of its science mission phase, the microPPT-based ACS option promises greater redundancy and robustness for the SPI mission. For other sailing missions, where the sail is never jettisoned, this secondary ACS provides a lower-cost, lower-mass propulsion for deployment control and greater redundancy than any traditional reaction-jet control system. This paper presents an overview nf the state--of-the--art microPPT technology, the design requirements of microPPTs for solar sail attitude control, and the preliminary ACS design and simulation results.

Wie, Bong↗
NASA NTRSDate not supplied

Analytical Investigation of Propellant Slosh Stability Boundary on a Space Vehicle

The effect of propellant sloshing upon the stability of a liquid-propelled space vehicle has been studied extensively. For a typical space vehicle with thrust vector control and a single slosh tank, the slosh danger zone is located between the vehicle center of mass and the center of percussion. If the slosh mass is located between these two locations, baffles may be required to provide additional damping for stability. In this work, the methodology behind the classic single tank solution analytical is extended to a tandem tank configuration where the tanks are located along the vehicle centerline or symmetrically offset from the centerline. Secondly, the slosh stability boundary for a vehicle with pairs of outboard reaction jets, rather than thrust vectoring, for attitude control is studied. Finally, the impact of aerodynamics and vehicle axial acceleration on the classic danger zone solution are analyzed.

Jing Pei↗
NASA NTRSDate not supplied

Analytical Investigation of Propellant Slosh Stability Boundary on a Space Vehicle

The effect of propellant sloshing upon the stability of a liquid-propelled space vehicle has been studied extensively. For a typical space vehicle with thrust vector control and asingle slosh tank, the Bauer slosh danger zone is located between the vehicle center of mass and the center of percussion while ignoring effects like aerodynamics and axial acceleration. If the slosh mass is located between these two locations, baffles may be required toprovide additional damping for stability. Although this criteria is widely used in the launch vehicle flight controls community, its application is limited to the aforementioned configuration and assumptions. In this work, the methodology behind the classic single-tank criteria is extended to other tank configurations and includes previously ignored effects. First, the variation of the classic danger zone for a tandem tank configuration where the tanks are located along the vehicle centerline or symmetrically offset from the centerline is investigated. Second, a vehicle with a single centerline tank and pair of outboard reaction jets, rather than thrust vectoring, for attitude control is studied. Finally, the impacts of aerodynamics and vehicle axial acceleration on the classic single-tank criteria are analyzed.

Jing Pei↗
NASA NTRS2006

Preliminary Study Using Forward Reaction Control System Jets During Space Shuttle Entry

Failure or degradation of the flight control system, or hull damage, can lead to loss of vehicle control during entry. Possible failure scenarios are debris impact and wing damage that could result in a large aerodynamic asymmetry which cannot be trimmed out without additional yaw control. Currently the space shuttle uses aerodynamic control surfaces and Reaction Control System jets to control attitude. The forward jets are used for orbital maneuvering only, while the aft jets are used for yaw control during entry. This paper develops a controller for using the forward reaction control system jets as an additional control during entry, and assesses its value and feasibility during failure situations. Forward-aft jet blending logic is created, and implemented on a simplified model of the space shuttle entry flight control system. The model is validated and verified on the nonlinear, six degree-of-freedom Shuttle Engineering Simulator. A rudimentary human factors study was undertaken using the forward cockpit simulator at Johnson Space Center, to assess flying qualities of the new system and pilot workload. Results presented in the paper show that the combination of forward and aft jets provides useful additional yaw control, in addition to potential fuel savings and the ability to balance the use of the fuel in the forward and aft tanks to meet availability constraints of both forward and aft fuel tanks. Piloted simulation studies indicated that using both sets of jets while flying a damaged space shuttle reduces pilot workload, and makes the vehicle more responsive.

Restrepo, Carolina↗
NASA NTRS2010

Estimation and Modeling of Enceladus Plume Jet Density Using Reaction Wheel Control Data

The Cassini spacecraft was launched on October 15, 1997 by a Titan 4B launch vehicle. After an interplanetary cruise of almost seven years, it arrived at Saturn on June 30, 2004. In 2005, Cassini completed three flybys of Enceladus, a small, icy satellite of Saturn. Observations made during these flybys confirmed the existence of a water vapor plume in the south polar region of Enceladus. Five additional low-altitude flybys of Enceladus were successfully executed in 2008-9 to better characterize these watery plumes. The first of these flybys was the 50-km Enceladus-3 (E3) flyby executed on March 12, 2008. During the E3 flyby, the spacecraft attitude was controlled by a set of three reaction wheels. During the flyby, multiple plume jets imparted disturbance torque on the spacecraft resulting in small but visible attitude control errors. Using the known and unique transfer function between the disturbance torque and the attitude control error, the collected attitude control error telemetry could be used to estimate the disturbance torque. The effectiveness of this methodology is confirmed using the E3 telemetry data. Given good estimates of spacecraft's projected area, center of pressure location, and spacecraft velocity, the time history of the Enceladus plume density is reconstructed accordingly. The 1 sigma uncertainty of the estimated density is 7.7%. Next, we modeled the density due to each plume jet as a function of both the radial and angular distances of the spacecraft from the plume source. We also conjecture that the total plume density experienced by the spacecraft is the sum of the component plume densities. By comparing the time history of the reconstructed E3 plume density with that predicted by the plume model, values of the plume model parameters are determined. Results obtained are compared with those determined by other Cassini science instruments.

Lee, Allan Y.↗
NASA NTRS2010

Estimation and Modeling of Enceladus Plume Jet Density Using Reaction Wheel Control Data

The Cassini spacecraft was launched on October 15, 1997 by a Titan 4B launch vehicle. After an interplanetary cruise of almost seven years, it arrived at Saturn on June 30, 2004. In 2005, Cassini completed three flybys of Enceladus, a small, icy satellite of Saturn. Observations made during these flybys confirmed the existence of a water vapor plume in the south polar region of Enceladus. Five additional low-altitude flybys of Enceladus were successfully executed in 2008-9 to better characterize these watery plumes. The first of these flybys was the 50-km Enceladus-3 (E3) flyby executed on March 12, 2008. During the E3 flyby, the spacecraft attitude was controlled by a set of three reaction wheels. During the flyby, multiple plume jets imparted disturbance torque on the spacecraft resulting in small but visible attitude control errors. Using the known and unique transfer function between the disturbance torque and the attitude control error, the collected attitude control error telemetry could be used to estimate the disturbance torque. The effectiveness of this methodology is confirmed using the E3 telemetry data. Given good estimates of spacecraft's projected area, center of pressure location, and spacecraft velocity, the time history of the Enceladus plume density is reconstructed accordingly. The 1-sigma uncertainty of the estimated density is 7.7%. Next, we modeled the density due to each plume jet as a function of both the radial and angular distances of the spacecraft from the plume source. We also conjecture that the total plume density experienced by the spacecraft is the sum of the component plume densities. By comparing the time history of the reconstructed E3 plume density with that predicted by the plume model, values of the plume model parameters are determined. Results obtained are compared with those determined by other Cassini science instruments.

Lee, Allan Y.↗
NASA NTRS1974

Effects of reaction control system jet flow field interactions on the aerodynamic characteristics of a 0.010-scale space shuttle orbiter model in the Langley Research Center 31 inch CFHT (OA85)

An experimental investigation was conducted to obtain detailed effects on supersonic vehicle hypersonic aerodynamic and stability and control characteristics of reaction control system jet flow field interactions with the local vehicle flow field. A 0.010-scale model was used. Six-component force data and wing, elevon, and body flap surface pressure data were obtained through an angle-of-attack range of -10 to +35 degrees with 0 deg angle of sideslip. The test was conducted with yaw, pitch and roll jet simulation at a free-stream Mach number of 10.3 and reaction control system plume simulation of flight dynamic pressures of 5, 10 and 20 PSF.

Daileda, J. J.↗
NASA NTRS1975

Space shuttle orbiter reaction control system jet interaction study

The space shuttle orbiter has forward mounted and rear mounted Reaction Control Systems (RCS) which are used for orbital maneuvering and also provide control during entry and abort maneuvers in the atmosphere. The effects of interaction between the RCS jets and the flow over the vehicle in the atmosphere are studied. Test data obtained in the NASA Langley Research Center 31 inch continuous flow hypersonic tunnel at a nominal Mach number of 10.3 is analyzed. The data were obtained with a 0.01 scale force model with aft mounted RCS nozzles mounted on the sting off of the force model balance. The plume simulations were accomplished primarily using air in a cold gas simulation through scaled nozzles, however, various cold gas mixtures of Helium and Argon were also tested. The effect of number of nozzles was tested as were limited tests of combined controls. The data show that RCS nozzle exit momentum ratio is the primary correlating parameter for effects where the plume impinges on an adjacent surface and mass flow ratio is the parameter where the plume interaction is primarily with the external stream. An analytic model of aft mounted RCS units was developed in which the total reaction control moments are the sum of thrust, impingement, interaction, and cross-coupling terms.

Rausch, J. R.↗
NASA NTRS2011

PLIF Study of Mars Science Laboratory Capsule Reaction Control System Jets

Nitric-oxide planar laser-induced fluorescence (NO PLIF) was used to visualize the flow in the wake of a Mars Science Lab (MSL) entry capsule with activated reaction control system (RCS) jets in NASA Langley Research Center s 31-Inch Mach 10 Air Tunnel facility. Images were processed using the Virtual Diagnostics Interface (ViDI) method, which brings out the three-dimensional nature of the flow visualization data while showing the relative location of the data with respect to the model. Comparison of wind-on and wind-off results illustrates the effect that the hypersonic crossflow has on the trajectory and structure of individual RCS jets. The visualization and comparison of both single and multiple activated RCS jets indicate low levels of jet-jet interaction. Quantitative streamwise velocity was also obtained via NO PLIF molecular tagging velocimetry (MTV).

Johansen, C. T.↗
NASA NTRS2011

PLIF Study of Mars Science Laboratory Capsule Reaction Control System Jets

Nitric-oxide planar laser-induced fluorescence (NO PLIF) was used to visualize the flow in the wake of a Mars Science Lab (MSL) entry capsule with activated reaction control system (RCS) jets in NASA Langley Research Center's 31-Inch Mach 10 Air Tunnel facility. Images were processed using the Virtual Diagnostics Interface (ViDI) method, which brings out the three-dimensional nature of the flow visualization data while showing the relative location of the data with respect to the model. Comparison of wind-on and wind-off results illustrates the effect that the hypersonic crossflow has on the trajectory and structure of individual RCS jets. The visualization and comparison of both single and multiple activated RCS jets indicate low levels of jet-jet interaction. Quantitative streamwise velocity was also obtained via NO PLIF molecular tagging velocimetry (MTV).

Johansen, C. T.↗