Electrical resistivity and conductivity of tungsten-fiber-reinforced copper composites
Electric resistivity and conductivity of tungsten- fiber-reinforced copper composites made by liquid phase infiltration techniques
TUNGSTEN↗
SEARCH · Search NASA
Results for “REINFORCING FIBER”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Damping mechanisms in fiber reinforced laminates
Low strain damping in fiber reinforced composite materials is due to material loss factors in both fibers and matrix materials. The high modulus of the fibers makes up for the low damping factor. Strains high enough to cause transverse layer cracking in laminates with organic matrix materials causes a large permanent increase in the damping factor. This increase is not due to the transverse cracks but rather to short microcracks in the high shear strain regions. Other damping mechanisms at high strains are also discussed.
Plunkett, R.↗
Mechanical joint performances of friction self-piercing riveted carbon fiber reinforced polymer and AZ31B Mg alloy
Carbon fiber reinforced polymer (CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting (F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load (>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads (<1 kN). From fractography, the crack initiation for lower peak load (<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.
36 MATERIALS SCIENCE↗
Carbon Fiber Reinforced Carbon Composite Valve for an Internal Combustion Engine
A carbon fiber reinforced carbon composite valve for internal combustion engines and the like formed of continuous carbon fibers throughout the valve's stem and head is disclosed. The valve includes braided carbon fiber material over axially aligned unidirectional carbon fibers forming a valve stem; the braided and unidirectional carbon fibers being broomed out at one end of the valve stem forming the shape of the valve head; the valve-shaped structure being densified and rigidized with a matrix of carbon containing discontinuous carbon fibers: and the finished valve being treated to resist oxidation. Also disclosed is a carbon matrix plug containing continuous and discontinuous carbon fibers and forming a net-shape valve head acting as a mandrel over which the unidirectional and braided carbon fibers are formed according to textile processes. Also disclosed are various preform valves and processes for making finished and preform carbon fiber reinforced carbon composite valves.
Rivers, H. Kevin↗
Analysis of Stress-rupture and Creep Properties of Tungsten Fiber Reinforced Copper Composites
Stress rupture and creep properties analyzed in tungsten fiber reinforced copper composites
REINFORCING FIBER↗
Fiber-Reinforced Slip Castings
Addition of silica fibers greatly reduces shrinkage and cracking during casting of ceramics. Fiber-reinforced slip-cast silica ceramics are also tougher and have lower dielectric loss. Silica fibers are hyperpure material containing only 1 part per million total metal-ion impurities. Hyperpure fibers ensure high reflectance and allow casting to be fired at temperature greater than 2,200 degrees F without loss of strength from devitrification.
Blome, J. C.↗
Predictive multiscale modeling for Unidirectional Carbon Fiber Reinforced Polymers
This paper presents a predictive multiscale modeling scheme for Unidirectional (UD) Carbon Fiber Reinforced Polymers (CFRP). A bottom-up modeling procedure is discussed for predicting the performance of UD structures. UD material responses are computed from high fidelity Representative Volume Elements (RVEs). A data-driven Reduced Order Modeling approach compresses RVEs into Reduced Order Models so material responses can be computed in a concurrent fashion along with the structural level simulation. The approach presented in this paper is validated against experimental data and is believed to provide design guidance for future fiber reinforced polymers development.
36 MATERIALS SCIENCE↗
Theory of fiber reinforced materials
A unified and rational treatment of the theory of fiber reinforced composite materials is presented. Fundamental geometric and elasticity considerations are throughly covered, and detailed derivations of the effective elastic moduli for these materials are presented. Biaxially reinforced materials which take the form of laminates are then discussed. Based on the fundamentals presented in the first portion of this volume, the theory of fiber-reinforced composite materials is extended to include viscoelastic and thermoelastic properties. Thermal and electrical conduction, electrostatics and magnetostatics behavior of these materials are discussed. Finally, a brief statement of the very difficult subject of physical strength is included.
Hashin, Z.↗
Effect of fiber reinforcement on the process parameters of injection molding manufacturing process
Use of fillers with the resin is common in injection molding manufacturing technique to enhance the stiffness and strength of the manufactured components. However, the addition of fillers changes the rheological and mechanical properties of the material, required adjustments in the process parameters used for the manufacturing. The present study aims to investigate this impact of fillers on the process parameters of the injection molding manufacturing process. Neat Acrylonitrile Butadiene Styrene (ABS) and ABS reinforced with short glass fibers are used as the materials to perform the comprehensive numerical analysis including complete process sequence, namely filling, packing, cooling and warpage. Parametric studies are conducted to optimize the manufacturing process for minimal warpage (or shrinkage) in the produced part. The selected process parameters for the parametric study include cooling time, packing pressure, and mold temperature, all of which directly impact the quality of the manufactured parts. The optimal values obtained for these parameters are compared to examine the effect fiber reinforcement has on the manufacturing process.
Garg, Nikhil↗
A review of carbon fiber reinforced metal matrix composites - The potential of large- diameter carbon-base monofilaments
Carbon base multifiber yarns for metal matrix composites reinforcement, considering fiber strength degradation minimization methods
Mcdanels, D. L.↗
Fabrication of Fiber-Reinforced Celsian Matrix Composites
A method has been developed for the fabrication of small diameter, multifilament tow fiber reinforced ceramic matrix composites. Its application has been successfully demonstrated for the Hi-Nicalon/celsian system. Strong and tough celsian matrix composites, reinforced with BN/SiC-coated Hi-Nicalon fibers, have been fabricated by infiltrating the fiber tows with the matrix slurry, winding the tows on a drum, cutting and stacking of the prepreg tapes in the desired orientation, and hot pressing. The monoclinic celsian phase in the matrix was produced in situ, during hot pressing, from the 0.75BaO-0.25SrO-Al2O3-2SiO2 mixed precursor synthesized by solid state reaction from metal oxides. Hot pressing resulted in almost fully dense fiber-reinforced composites. The unidirectional composites having approx. 42 vol% of fibers exhibited graceful failure with extensive fiber pullout in three-point bend tests at room temperature. Values of yield stress and strain were 435 +/- 35 MPa and 0.27 +/- 0.01 percent, respectively, and ultimate strengths of 900 +/- 60 MPa were observed. The Young's modulus of the composites was measured to be 165 +/- 5 GPa.
Bansal, Narottam P.↗
Predicted inlet gas temperatures for tungsten fiber reinforced superalloy turbine blades
Tungsten fiber-reinforced superalloy composite (TFRS) impingement-cooled turbine blade inlet gas temperatures were calculated taking into account material spanwise strength, thermal conductivity, material oxidation resistance, fiber-matrix interaction, and coolant flow. Measured values of TFRS thermal conductivities are presented. Calculations indicate that blades made of 30 volume percent fiber content TFRS having a 12,000 N-m/kg stress-to-density ratio while operating at 40 atm and a 0.06 coolant flow ratio could permit a turbine blade inlet gas temperature of over 1900 K. This is more than 150 K greater than similar superalloy blades.
Winsa, E. A.↗
Materials Development and Advanced Process Simulation for Additive Manufacturing with Fiber-Reinforced Thermoplastics (Final Technical Report)
DuPont, Local Motors, and the Composites Manufacturing and Simulation Center (CMSC) at Purdue worked together to advance process simulation capabilities for Additive Manufacturing (AM) and develop printable short fiber reinforced semi-crystalline engineering thermoplastics suitable for vehicle components. DuPont provided one candidate thermoplastic material, which was evaluated against the following three criteria: 1) Printability using extrusion additive manufacturing processes. 2) Suitability for vehicle applications based on mechanical coupon screening tests. 3) Predictive capability of process simulations. Indiana Manufacturing Institute provided modeling and simulation technology and access to Purdue’s lab scale AM printer. Local Motors provided mechanical property requirements and printed demonstration prototype components using their Thermwood Large Scale Additive Manufacturing (LSAM) printer. To meet the performance and cost requirements of the automotive industry, high fiber content semi-crystalline engineering materials are required. Printing experience and property data for a 50% by weight short glass fiber reinforced material were gathered. Further, material properties required for simulating the printing process with the glass-fiber reinforced material were characterized. Knowledge was acquired with regards to the processability and performance of this thermoplastic material. Predictions of part deformation and crystallinity level were verified against experimental observations. Any significant results other than verification of simulation, e.g., novel material identified here would be impactful.
36 MATERIALS SCIENCE↗
Passive sensing of a microparticle modified hybrid, fiber-reinforced composite
The widespread commercial adoption of high-performance, fiber-reinforced composites has pushed research interests toward the next generation of composites. These new composites are tasked with integrating additional functionalities into the structures without causing a trade-off in mechanical performance. One such functionality that has received significant interest is sensing. This is especially important for composites using high-performance fibers (e.g., carbon fiber) because their strain-to-failure is relatively low, resulting in brittle fracture. Besides, fiber damage can be hidden within the composite, potentially leading to premature catastrophic failure if not detected. In prior research, we demonstrated continuous feed-through deposition of ceramic nanoparticles on carbon fiber’s surface that simultaneously enhanced both the piezoresistive response and interlaminar shear strength. In this work, a similar continuous feed-through deposition process was used to demonstrate passive sensing and energy harvesting by integrating ferroelectric microparticles on the surface of electrically nonconductive fibers. The sensing and energy harvesting capabilities were characterized by mechanically straining composite beams and measuring the power generated. The improvements in mechanical properties are shown through interlaminar shear strength tests. Therefore, this research aims to demonstrate a high throughput, commercially scalable approach to coat fibers with ferroelectric microparticles that enable passive sensing as well as improved mechanical performance when fabricated into a fiber-reinforced composite.
Bowland, Christopher↗
Mechanical Properties of Continuous Fiber Reinforced Zirconium Diboride Matrix Composites
Continuous fiber reinforced zirconium diboride matrix composites, SCS-9a-(RBSiCZrB2)matrix, are being developed for leading edge, rocket nozzle and turbine engine applications. Recently, the composite materials have been characterized for tensile properties to 1250 C, the highest temperature tested. The tensile properties are fiber dominated as the matrix is microcracked on fabrication, but favorable failure characteristic are observed. Compression and shear mechanical testing results will be reported if completed. The effects of fiber volume fraction and matrix density on mechanical properties will be discussed. The target applications of the materials will be discussed. Specific testing being performed towards qualification for these applications will be included.
Stuffle, Kevin↗
Fiber-reinforced ceramic composites for Earth-to-orbit rocket engine turbines
Fiber reinforced ceramic matrix composites (FRCMC) are emerging materials systems that offer potential for use in liquid rocket engines. Advantages of these materials in rocket engine turbomachinery include performance gain due to higher turbine inlet temperature, reduced launch costs, reduced maintenance with associated cost benefits, and reduced weight. This program was initiated to assess the state of FRCMC development and to propose a plan for their implementation into liquid rocket engine turbomachinery. A complete range of FRCMC materials was investigated relative to their development status and feasibility for use in the hot gas path of earth-to-orbit rocket engine turbomachinery. Of the candidate systems, carbon fiber-reinforced silicon carbide (C/SiC) offers the greatest near-term potential. Critical hot gas path components were identified, and the first stage inlet nozzle and turbine rotor of the fuel turbopump for the liquid oxygen/hydrogen Space Transportation Main Engine (STME) were selected for conceptual design and analysis. The critical issues associated with the use of FRCMC were identified. Turbine blades were designed, analyzed and fabricated. The Technology Development Plan, completed as Task 5 of this program, provides a course of action for resolution of these issues.
Brockmeyer, Jerry W.↗
Creep behavior of tungsten fiber reinforced niobium metal matrix composites
Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared on a strength to density basis. The effect of fiber orientation on the creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.
Grobstein, T. L.↗
Creep behavior of tungsten fiber reinforced niobium metal matrix composites
Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.
Grobstein, Toni L.↗