SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The design characteristics of the XV-15 Tilt rotor research aircraft are presented. Particular attention is given to the following: control system; conversion system; and propulsion system. Flight test results are also reported.
The compound Rotor Systems Research Aircraft (RSRA) is designed to make high accuracy, simultaneous measurements of all rotor forces and moments in flight. Physical calibration of the rotor force- and moment-measurement system when installed in the aircraft is required to account for any errors and to ensure that measurement system accuracy is traceable to the National Bureau of Standards. The first static calibration and associated analysis has been completed with good results. Hysteresis was a potential cause of static calibration errors, but was found to be negligible in flight, and analytical methods have been devised to eliminate its effects on calibration data. Flight tests confirmed that the calibrated rotor loads measurement system performs as expected in flight, and that it can dependably make direct measurements of fuselage vertical drag in hover.
The rotor systems research aircraft (RSRA) has undergone ground and flight tests, primarily as a compound aircraft. The purpose was to train pilots and to check out and develop the design flight envelope. The preparation and flight test of the RSRA in the airplane, or fixed-wind, configuration are reviewed and the test results are discussed.
A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivatives were adequately determined by the flight test procedure and the MSR analysis method discussed herein.
A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivat
The purpose of this paper is to define a set of structural requirements which can be used for conceptual design studies of the Subsonic Single Aft eNgine (SUSAN) aircraft and the early design phases of a quarter scale flight research aircraft. SUSAN presents an architecture for a subsonic regional jet transport aircraft coupling a single turbofan engine to an electrified aircraft propulsion system (EAP). Presented within this paper are a consolidated set of requirements drawn from NASA, FAA (FAR), and non-government structural standards with a focus on loads. An example application of the breakout load tables and the approach for applying existing standards to those configurations is presented for the SUSAN 25% flight research vehicle. Positioning of the turbofan, electric engines, battery and the requirement for the 25% vehicle to be shippable in a cargo box are atypical structural design requirements. Particular focus is given to the primary aircraft structural elements such as the engine/tail mount, fuselage structure, and wing structure.
The purpose of this paper is to define a set of structural requirements which can be used for conceptual design studies of the Subsonic Single Aft eNgine (SUSAN) aircraft and the early design phases of a quarter scale flight research aircraft. SUSAN presents an architecture for a subsonic regional jet transport aircraft coupling a single turbofan engine to an electrified aircraft propulsion system (EAP). Presented within this paper are a consolidated set of requirements drawn from NASA, FAA (FAR), and non-government structural standards with a focus on loads. An example application of the breakout load tables and the approach for applying existing standards to those configurations is presented for the SUSAN 25% flight research vehicle. Positioning of the turbofan, electric engines, battery and the requirement for the 25% vehicle to be shippable in a cargo box are atypical structural design requirements. Particular focus is given to the primary aircraft structural elements such as the engine/tail mount, fuselage structure, and wing structure.
The National Aeronautics and Space Administration (NASA) is leading government, industry and academic research effort known as Urban Air Mobility (UAM). The UAM activity goal is to develop the technology needed to make possible an urban air transportation system that makes use of human-crewed and crewless vehicles using automation, artificial intelligence and other technologies to safely and efficiently air transport people and goods within an urban environment. The NASA Langley Research Center (LaRC) created a UAM Flight Research Testbed Aircraft from a Cessna LC40 general aviation aircraft. The testbed has updated digital avionics and research systems needed to conduct flight research. The aircraft has two separate autopilots; a standard Federal Aviation Ad-ministration (FAA) certified system, and a modified research autopilot. The research autopilot has modifications that allow increased authority and enhancements to allow more automation and artificial intelligence controls. A network of three research computers hosts software to research several activities including automated air traffic sense and avoid, ground collision avoidance and obstacle avoidance. These UAM research activities involve automation and artificial intelligence technologies developed at three NASA centers. The NASA Langley, NASA Armstrong, and NASA Ames Research Centers are working together to develop and test these UAM technologies. This paper provides details of the systems, capabilities and research projects of the UAM Testbed Research Aircraft.
Solar constant and solar spectral irradiance measurements from high altitude research aircraft, discussing radiation measuring instruments
The NASA Ames/DSI oblique wing remotely piloted research aircraft is a highly unusual, variable remotely piloted vehicle whose configuration and capabilities are the result of certain initial design guidelines that, in terms of conventional aircraft structures and configurations, would be considered to be contradictory and unachievable. Accordingly, the novel design of the yawed wing RPV is at odds in many respects with conventional aircraft practice. Novelty, then, forms the first, unwritten, design guideline. This design is intended to move away from convention in geometry, structure, and materials. The specific guidelines followed in the design of the yawed wing RPV and a short discussion of the impact of each on the configuration of the vehicle are presented.
The three-man Rotor Systems Research Aircraft (RSRA) Emergency Escape System, the first system known to be fully qualified and operational in a rotary wing aircraft, will have two modes of operation: one providing for full in-flight egress, and the other for the severance of the rotor blades for a return to base as a fixed-wing aircraft. This paper describes the escape system's design principles, integration into the aircraft, qualification, and performance.
A wind-tunnel test was conducted at Ames Research Center to measure the aerodynamic characteristics of a joined-wing research aircraft (JWRA). This aircraft was designed to utilize the fuselage and engines of the existing NASA AD-1 aircraft. The JWRA was designed to have removable outer wing panels to represent three different configurations with the interwing joint at different fractions of the wing span. A one-sixth-scale wind-tunnel model of all three configurations of the JWRA was tested in the Ames 12-Foot Pressure Wind Tunnel to measure aerodynamic performance, stability, and control characteristics. The results of these tests are presented. Longitudinal and lateral-directional characteristics were measured over an angle of attack range of -7 to 14 deg and over an angle of sideslip range of -5 to +2.5 deg at a Mach number of 0.35 and a Reynolds number of 2.2x10(6)/ft. Various combinations of deflected control surfaces were tested to measure the effectiveness and impact on stability of several control surface arrangements. In addition, the effects on stall and post-stall aerodynamic characteristics from small leading-edge devices called vortilons were measured. The results of these tests indicate that the JWRA had very good aerodynamic performance and acceptable stability and control throughout its flight envelope. The vortilons produced a profound improvement in the stall and post-stall characteristics with no measurable effects on cruise performance.
A description is given of the capabilities and limitations of the Rotor Systems Research Aircraft (RSRA) that was demonstrated during the development contract, and assesses the expected research capabilities of the RSRA on delivery to the government.
NASA's Ames Research Center has developed and is testing a new integrated flight and propulsion control system that will help pilots land aircraft in adverse weather conditions and in small confined ares (such as, on a small ship or flight deck). The system is being tested in the V/STOL (Vertical/Short Takeoff and Landing) Systems research Aircraft (VSRA), which is a modified version of the U.S. Marine Corps's AV-8B Harrier jet fighter, which can take off and land vertically. The new automated flight control system features both head-up and panel-mounted computer displays and also automatically integrates control of the aircraft's thrust and thrust vector control, thereby reducing the pilot's workload and help stabilize the aircraft for landing. Visiting pilots will be encouraged to test the new system and provide formal evaluation flights data and feedback. An actual flight test and the display panel of control system are shown in this video.
The program to design and build a Buffalo/Spey Augmentor-Wing research aircraft is presented. The development of an internally blown flap system for the generation of powered lift is discussed. Modification, development, and testing of the Rolls-Royce Spey engine are reported. The ground tests and first flights of the aircraft are described and the application of the internally blown flap concept for short takeoff military transport aircraft is proposed.
Full scale static investigations were conducted on the Quiet Short Haul Research Aircraft (QSRA) to determine the thrust deflecting capabilities of the circulation control wing/upper surface blowing (CCW/USB) concept. This scheme, which combines favorable characteristics of both the A-6/CCW and QSRA, employs the flow entrainment properties of CCW to pneumatically deflect engine thrust in lieu of the mechanical USB flap system. Results show that the no moving parts blown system produced static thrust deflections in the range of 40 deg to 97 deg (depending on thrust level) with a CCW pressure of 208,900 Pa (30.3 psig). In addition, the ability to vary horizontal forces from thrust to drag while maintaining a constant vertical (or lift) value was demonstrated by varying the blowing pressure. The versatility of the CCW/USB system, if applied to a STOL aircraft, was confirmed, where rapid conversion from a high drag approach mode to a thrust recovering waveoff or takeoff configuration could be achieved by nearly instantaneous blowing pressure variation.
The two Rotor Systems Research Aircraft (RSRA) are flight vehicles with unique measurement capabilities. The primary goal of the RSRA is direct measurement of rotor forces and moments in flight. This is accomplished through a rotor force and moment measurement system comprised of load cells and/or hydro-pneumatic isolator units which are integral to the aircraft structure. Due to structural flexibility, the aircraft must undergo a physical calibration. A static calibration of the first RSRA has been completed, and data analysis has progressed through determination of a linear calibration algorithm. Design, development, and operation of the RSRA rotor force and moment measurement system and the Static Calibration Facility are described, and results of the calibration are presented.
Two candidate control systems for the Vertical/Short Takeoff and Landing (V/STOL) Research Aircraft (VSRA) are described, both of which are limited-authority, digital, fly-by wire variants of the original YAV-8B Harrier control system. The performance of these systems was compared with that of an ideal, full-authority system in simulated, adverse-weather V/STOL shipboard operations using the Ames Research Center's Vertical Motion Simulator. Both systems showed some performance degradation relative to the ideal, but both were adequate to meet VSRA program objectives. The favored system, selected because of safety considerations, was further simulated using a precision visual hovering task that verified its acceptability.