Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotation operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Spatial atomic layer deposition for coating flexible porous Li-ion battery electrodes

Ultrathin atomic layer deposition (ALD) coatings on the electrodes of Li-ion batteries can enhance the capacity stability of the Li-ion batteries. To commercialize ALD for Li-ion battery production, spatial ALD is needed to decrease coating times and provide a coating process compatible with continuous roll-to-roll (R2R) processing. The porous electrodes of Li-ion batteries provide a special challenge because higher reactant exposures are needed for spatial ALD in porous substrates. This work utilized a modular rotating cylinder spatial ALD reactor operating at rotation speeds up to 200 revolutions/min (RPM) and substrate speeds up to 200 m/min. The conditions for spatial ALD were adjusted to coat flexible porous substrates. The reactor was initially used to characterize spatial Al2O3 and ZnO ALD on flat, flexible metalized polyethylene terephthalate foils. These studies showed that slower rotation speeds and spacers between the precursor module and the two adjacent pumping modules could significantly increase the reactant exposure. The modular rotating cylinder reactor was then used to coat flexible, model porous anodic aluminum oxide (AAO) membranes. The uniformity of the ZnO ALD coatings on the porous AAO membranes was dependent on the aspect ratio of the pores and the reactant exposures. Larger reactant exposures led to better uniformity in the pores with higher aspect ratios. The reactant exposures were increased by adding spacers between the precursor module and the two adjacent pumping modules. The modular rotating cylinder reactor was also employed for Al2O3 ALD on porous LiCoO2 (LCO) battery electrodes. Uniform Al coverages were obtained using spacers between the precursor module and the two adjacent pumping modules at rotation speeds of 25 and 50 RPM. The LCO electrodes had a thickness of ~49 um and pores with aspect ratios of ~12-25. Coin cells were then constructed using the ALD-coated LCO electrodes and were tested to determine their battery performance. The capacity of the Al2O3 ALD-coated LCO battery electrodes was measured versus the number of charge-discharge cycles. Both temporal and spatial ALD processing methods led to higher capacity stability compared with uncoated LCO battery electrodes. The results for improved battery performance were comparable for temporal and spatial ALD-coated electrodes. The next steps are also presented for scale-up to R2R spatial ALD using the modular rotating cylinder reactor.

25 ENERGY STORAGE↗

Eddy current damper

A high torque capacity eddy current damper used as a rate limiting device for a large solar array deployment mechanism is discussed. The eddy current damper eliminates the problems associated with the outgassing or leaking of damping fluids. It also provides performance advantages such as damping torque rates, which are truly linear with respect to input speed, continuous 360 degree operation in both directions of rotation, wide operating temperature range, and the capability of convenient adjustment of damping rates by the user without disassembly or special tools.

Ellis, R. C.↗

Rotating reverse osmosis: a dynamic model for flux and rejection

Reverse osmosis (RO) is a compact process for the removal of ionic and organic pollutants from contaminated water. However, flux decline and rejection deterioration due to concentration polarization and membrane fouling hinders the application of RO technology. In this study, a rotating cylindrical RO membrane is theoretically investigated as a novel method to reduce polarization and fouling. A dynamic model based on RO membrane transport incorporating concentration polarization is used to predict the performance of rotating RO system. Operating parameters such as rotational speed and transmembrane pressure play an important role in determining the flux and rejection in rotating RO. For a given geometry, a rotational speed sufficient to generate Taylor vortices in the annulus is essential to maintain high flux as well as high rejection. The flux and rejection were calculated for wide range of operating pressures and rotational speeds. c 2001 Elsevier Science B.V. All rights reserved.

Non-NASA Center↗

A spin observable for a Dirac particle

We discuss the form of the spin operator in relativistic quantum mechanics. We derive the form of the spin operator in the case when the states with negative energies are admitted. It appears that for a Dirac particle the spin operator reduces to the so called mean-spin operator introduced by Foldy and Wouthuysen. We show that the spin operator transforms under Lorentz group action according to an operator Wigner rotation, analogously as a Bloch vector describing polarization of a particle in momentum representation. - Highlights: Black-Right-Pointing-Pointer We examine the problem of a relativistic spin operator in the case of a Dirac particle. Black-Right-Pointing-Pointer We show that a proper spin operator coincides for positive energies with the operator used in quantum field theory. Black-Right-Pointing-Pointer This operator can be extended for negative energies. Black-Right-Pointing-Pointer We show that this operator is equivalent to the so called mean-spin operator introduced by Foldy and Wouthuysen. Black-Right-Pointing-Pointer The spin operator transforms under Lorentz group action according to the operator Wigner rotation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multi-axis oscillating flight simulator

An apparatus for simulating an oscillating flight path is provided. The apparatus comprises a slide extending along a first axis; a support structure slidably coupled to the slide; and a table connected to the support structure. The support structure is operable to move along the slide. The table is coupled to the support structure and operable to rotate about a second axis orthogonal to the first axis. The table comprises a surface that is parallel to the second axis and that is operable to rotate about a third axis orthogonal to the second axis.

Dark, Philip Ryan↗

Some operational aspects of a rotating advanced-technology space station for the year 2025

The study of an Advanced Technology Space Station which would utilize the capabilities of subsystems projected for the time frame of the years 2000 to 2025 is discussed. The study includes tradeoffs of nuclear versus solar dynamic power systems that produce power outputs of 2.5 megawatts and analyses of the dynamics of the spacecraft of which portions are rotated for artificial gravity. The design considerations for the support of a manned Mars mission from low Earth orbit are addressed. The studies extend to on-board manufacturing, internal gas composition effects, and locomotion and material transfer under artificial gravity forces. The report concludes with an assessment of technology requirements for the Advanced Technology Space Station.

Queijo, M. J.↗

Operational Stability Limits in Rotating Detonation Engine Numerical Simulations

An instability is described which arises in computational fluid dynamic (CFD) simulations of semi-idealized rotating detonation engines (RDE) configured with a throat at the exit. Its existence is verified by examining output from two independently developed CFD codes simulating the same configuration and producing solutions that agree well. The instability is shown to be thermo-acoustic in that a spatial integral of the product of pressure and heat release fluctuations develops a regular oscillation which grows in time. The instability can become severe enough to cause detonation failure. Its onset is shown to be closely linked to the size of the exit throat and the size of the inlet restriction; both parameters that strongly influence RDE performance. It is shown that the instability places a cap on ideal RDEperformance, but that an optimized exhaust throat and inlet restriction combination still yields substantial pressure gain. Other parametric sensitivities are also examined in terms ofinstability growth. These include axial length, inlet manifold pressure, and air-fuel ratio.

Paxson, Daniel E.↗

Design optimization of MR-compatible rotating anode x-ray tubes for stable operation

Purpose: Hybrid x-ray/MR systems can enhance the diagnosis and treatment of endovascular, cardiac, and neurologic disorders by using the complementary advantages of both modalities for image guidance during interventional procedures. Conventional rotating anode x-ray tubes fail near an MR imaging system, since MR fringe fields create eddy currents in the metal rotor which cause a reduction in the rotation speed of the x-ray tube motor. A new x-ray tube motor prototype has been designed and built to be operated close to a magnet. To ensure the stability and safety of the motor operation, dynamic characteristics must be analyzed to identify possible modes of mechanical failure. In this study a 3D finite element method (FEM) model was developed in order to explore possible modifications, and to optimize the motor design. The FEM provides a valuable tool that permits testing and evaluation using numerical simulation instead of building multiple prototypes.Methods: Two experimental approaches were used to measure resonance characteristics: the first obtained the angular speed curves of the x-ray tube motor employing an angle encoder; the second measured the power spectrum using a spectrum analyzer, in which the large amplitude of peaks indicates large vibrations. An estimate of the bearing stiffness is required to generate an accurate FEM model of motor operation. This stiffness depends on both the bearing geometry and adjacent structures (e.g., the number of balls, clearances, preload, etc.) in an assembly, and is therefore unknown. This parameter was set by matching the FEM results to measurements carried out with the anode attached to the motor, and verified by comparing FEM predictions and measurements with the anode removed. The validated FEM model was then used to sweep through design parameters [bearing stiffness (1×10{sup 5}–5×10{sup 7} N/m), shaft diameter (0.372–0.625 in.), rotor diameter (2.4–2.9 in.), and total length of motor (5.66–7.36 in.)] to increase the fundamental frequency past the operating range at 50 Hz.Results: The first large vibration during the prototype motor operation was obtained at 21.64±0.68 Hz in the power spectrum. An abrupt decrease in acceleration occurred at 21.5 Hz due to struggling against the resonance vibrations. A bearing stiffness of 1.2×10{sup 5} N/m in the FEM simulation was used to obtain a critical speed of 21.4 Hz providing 1.1% error. This bearing stiffness value and the 3D model were then confirmed by the experiments with the anode removed, demonstrating an agreement within 6.4% between simulation results and measurements. A calculated first critical frequency (fundamental frequency) of 68.5 Hz was obtained by increasing the bearing stiffness to 1×10{sup 7} N/m and increasing the shaft diameter by 68.0%. Reducing the number of bearings in the design permits decreasing the total length of the motor by 1.7 in., and results in a fundamental frequency of 68.3 Hz in concert with additional changes (shaft diameter of 0.625 in., rotor diameter of 2.4 in., and bearing stiffness of 1×10{sup 6} N/m).Conclusions: An FEM model of the x-ray tube motor has been implemented and experimentally validated. A fundamental frequency above the operational rotation speed can be achieved through modification of multiple design parameters, which allows the motor to operate stably and safely in the MR environment during the repeated acceleration/deceleration cycles required for an interventional procedure. The validated 3D FEM model can now be used to investigate trade-offs between generated torque, maximum speed, and motor inertia to further optimize motor design.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Gyrokinetic simulations including the centrifugal force in a rotating tokamak plasma

Tokamak experiments operate with a rotating plasma, with toroidal velocity which can be driven externally but can also arise spontaneously. In the frame that corotates with the plasma, the effects of the centrifugal force are felt through a centrifugal drift and an enhanced mirror force [Peeters et al., Phys. Plasmas 16, 042310 (2009)]. These inertial terms become important in the case of strong rotation, as is common in spherical devices, and are also important for heavy impurity ions even at small toroidal velocities. In this work, the first gyrokinetic simulations including the centrifugal force in a strongly rotating plasma are presented. The enhanced mirror force redistributes density over a flux surface and modifies the trapping condition, destabilizing trapped electron modes. At intermediate scales this can result in promotion of the trapped electron mode over the ion temperature gradient (ITG) mode as the dominant instability, which under marginal conditions could result in an enhanced electron heat flux. The centrifugal drift acts to damp the residual zonal flow of the geoacoustic mode, while its frequency is increased. For nonlinear ITG dominated turbulence, increased trapped electron drive and reduced zonal flow lead to an increase in ion heat diffusivity if the increased rotation is not accompanied by rotational shear stabilization. An increased fraction of slow trapped electrons enhances the convective particle pinch, leading to an increase in the steady state density gradient with strong rotation. Linear ITG mode results show an increased pinch of heavy trace impurities due to their strong centrifugal trapping.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

The performance impact of flow reversal at the inlet of an airbreathing rotating detonation engine (RDE) is investigated using 2 and 3-dimensional computational fluid dynamic (CFD) simulations. Flow reversal, or backflow, occurs in RDE inlets in the high-pressure region directly behind the rotating detonation front. This is also where most of the engine thrust or pressure gain is produced. The amount of backflow relative to throughflow depends on the inlet design. For the present work, a simple annular ‘slit’ design is used. The simulations are idealized in several ways, including that fuel and air are premixed, but prevented from reacting when within the inlet region. The results indicate that even with idealizations, the impact of inlet backflow on pressure gain can be substantial. The simulations also reveal an intriguing instability that develops in certain configurations. The mass flow rate into the RDE begins to oscillate at a regular frequency that is substantially less than the detonation rotational frequency. This is accompanied by oscillations in the detonation height. The oscillation amplitude grows over time until the detonation ultimately fails. Both the performance and instability results emphasize the need for carefully designed RDE inlets that provide low loss when flow is in the forward direction, but high resistance when the flow is reversed. Development of such high-diodicity inlets is critical to achieving pressure gain in airbreathing RDE’s.

Detonation↗

Computational Assessment of Inlet Backflow Effects on Rotating Detonation Engine Performance and Operability

The performance impact of flow reversal at the inlet of an airbreathing rotating detonation engine (RDE) is investigated using 2 and 3-dimensional computational fluid dynamic (CFD) simulations. Flow reversal, or backflow, occurs in RDE inlets in the high-pressure region directly behind the rotating detonation front. This is also where most of the engine thrust or pressure gain is produced. The amount of backflow relative to throughflow depends on the inlet design. For the present work, a simple annular ‘slit’ design is used. The simulations are idealized in several ways, including that fuel and air are premixed, but prevented from reacting when within the inlet region. The results indicate that even with idealizations, the impact of inlet backflow on pressure gain can be substantial. The simulations also reveal an intriguing instability that develops in certain configurations. The mass flow rate into the RDE begins to oscillate at a regular frequency that is substantially less than the detonation rotational frequency. This is accompanied by oscillations in the detonation height. The oscillation amplitude grows over time until the detonation ultimately fails. Both the performance and instability results emphasize the need for carefully designed RDE inlets that provide low loss when flow is in the forward direction, but high resistance when the flow is reversed. Development of such high-diodicity inlets is critical to achieving pressure gain in airbreathing RDE’s.

detonation↗

Torsionally mediated spin-rotation hyperfine splittings at moderate to high J values in methanol

This paper presents an explanation based on torsionally mediated proton-spin–overall-rotation interaction for the observation of doublet hyperfine splittings in some Lamb-dip sub-millimeter-wave transitions between ground-state torsion-rotation states of E symmetry in methanol. These unexpected doublet splittings, some as large as 70 kHz, were observed for rotational quantum numbers in the range of J = 13 to 34, and K = − 2 to +3. Because they increase nearly linearly with J for a given branch, we confined our search for an explanation to hyperfine operators containing one nuclear-spin angular momentum factor I and one overall-rotation angular momentum factor J (i.e., to spin-rotation operators) and ignored both spin-spin and spin-torsion operators, since they contain no rotational angular momentum operator. Furthermore, since traditional spin-rotation operators did not seem capable of explaining the observed splittings, we constructed totally symmetric “torsionally mediated spin-rotation operators” by multiplying the E-species spin-rotation operator by an E-species torsional-coordinate factor of the form e{sup ±niα}. The resulting operator is capable of connecting the two components of a degenerate torsion-rotation E state. This has the effect of turning the hyperfine splitting pattern upside down for some nuclear-spin states, which leads to bottom-to-top and top-to-bottom hyperfine selection rules for some transitions, and thus to an explanation for the unexpectedly large observed hyperfine splittings. The constructed operator cannot contribute to hyperfine splittings in the A-species manifold because its matrix elements within the set of torsion-rotation A{sub 1} and A{sub 2} states are all zero. The theory developed here fits the observed large doublet splittings to a root-mean-square residual of less than 1 kHz and predicts unresolvable splittings for a number of transitions in which no doublet splitting was detected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved manual radio frequency direction finder

Antenna loop direction finder, consisting of two separate loops mounted rigidly together at right angles to each other, requires single rotation for operation. The loops, one for bearing, the other for sensing, are rotated manually. Sensing loop, in conjunction with nondirectional antenna, produces signal with directional pattern.

Greenwood, T. L.↗

Design and Operability of a Variably Premixed Rotating Detonation Engine for the Evaluation of Mixing Effects

The design of a variably premixed rotating detonation engine (RDE) is presented with preliminary experimental results. Premixed operation decouples the mixing process from the detonation cycle, enabling direct comparison with premixed simulations. A porous medium, formed into a ring of 6.45 mm radial thickness, serves as the premixture injector, arresting potential flash-back events. Two chamber geometries are tested, the first aimed at eliminating recirculation zones and comprised of a 7.62 mm wide channel, the width of which the porous injector occupies 85%. The second chamber geometry features a 10.7 mm channel width and a 3.08 mm wide backward-facing step on the internal diameter of the premixture injector. Transverse optical access is incorporated into the design using a transparent outer body. Tests were conducted at mixing conditions ranging from non-premixed to fully premixed with gaseous hydrogen and air reactants in the narrow-channel configuration. Engine operating modes and detonation wave speeds were characterized using aft-end high-speed chemiluminescence imaging, while detonation wave topology and heat release in the refill zone are captured by transverse imaging. A two-wave counterpropagating mode was most commonly observed in the narrow-channel configuration with wave speeds ranging from 49-67% of the theoretical Chapman-Jouguet (CJ) velocity. Fully premixed operation in the backward-facing step configuration rendered wave speeds up to 86% of CJ velocity, consistent with previous non-premixed results using the same channel width and a backward-facing step. These results demonstrate successful premixed RDE operation with high wave speeds and highlight the role of product recirculation zones in stabilizing the detonation cycle.

detonation↗

Design and Testing of a Water-Cooled Rotating Detonation Combustor at Elevated Operating Pressures - Abstract

This is an extended abstract being submitted for consideration that briefly describes the material that will be included in the final paper. This study will detail the design and testing of a water-cooled Rotating Detonation Combustor (RDC) that permits operation for extended periods of time ensuring that the device has reach a stable operating temperature. Extended run times also provides an opportunity to consider transient behaviors that occur as a result of altering the operating conditions such as equivalence ratio. The experimental setup is also unique in that it consists of a ducted exhaust with a downstream high-temperature valve that can control the pre-combustion pressure in the RDC independent of the combustor annulus and exit geometry. This paper will examine the results from the extended operation of the water-cooled RDC over a range of both transient and steady state equivalence ratios (0.5 - 1.0), pre-combustion operating pressures (0 - 207 kPa), mass flow rates (0.42 – 0.5 kg/sec) and air inlet throat area to combustor channel area ratios (0.09 – 0.32). All tests were performed while operating on hydrogen in air at a nominal air inlet temperature of 340 – 350 K. Limited data obtained at an elevated inlet air temperature of 480 K will also be discussed. Results suggest that under certain conditions the operating mode of the detonation wave can vary as it approaches a stable operating temperature. For the RDC tested, a stable operating temperature is not achieved until approximately 8-10 seconds of run time.

Ferguson, Donald↗

Experimental Investigation of Rotating Stall in a Research Multistage Axial Compressor

A collection of experimental data acquired in the NASA low-speed multistage axial compressor while operated in rotating stall is presented in this paper. The compressor was instrumented with high-response wall pressure modules and a static pressure disc probe for in-flow measurement, and a split-fiber probe for simultaneous measurements of velocity magnitude and flow direction. The data acquired to-date have indicated that a single fully developed stall cell rotates about the flow annulus at 50.6% of the rotor speed. The stall phenomenon is substantially periodic at a fixed frequency of 8.29 Hz. It was determined that the rotating stall cell extends throughout the entire compressor, primarily in the axial direction. Spanwise distributions of the instantaneous absolute flow angle, axial and tangential velocity components, and static pressure acquired behind the first rotor are presented in the form of contour plots to visualize different patterns in the outer (midspan to casing) and inner (hub to mid-span) flow annuli during rotating stall. In most of the cases observed, the rotating stall started with a single cell. On occasion, rotating stall started with two emerging stall cells. The root cause of the variable stall cell count is unknown, but is not attributed to operating procedures.

Lepicovsky, Jan↗