Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotor Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Aerodynamic interactions between a rotor and wing in hover

An experimental investigation of rotor/wing aerodynamic interactions in hover is described. The investigation consisted of both a large-scale and a small-scale test. A 0.658-scale V-22 rotor and wing was used in the large-scale test. Wing download, wing surface pressure, rotor performance, and rotor downwash data from the large-scale test are presented. A small-scale experiment was conducted to determine how changes in the rotor/wing geometry affected the aerodynamic interactions. These geometry variations included the distance between the rotor and wing, wing incidence angle, wing flap angle, rotor rotation direction, and configurations both with the rotor axis at the tip of the wing (tilt rotor configuration) and with the rotor axis at the center of the wing (compound helicopter configuration).

Felker, Fort F.↗
NASA NTRS1997

Neural Network Research on Tilt-Rotor Hover Performance

Results from a neural network study on XV-15 tilt-rotor hover performance are presented. Two XV-15 test data bases, acquired during separate tests conducted in the National Full-Scale Aerodynamics Complex at NASA Ames, were used in this study. The two XV-15 test data bases used were: the 1997 80- by 120-Foot Wind Tunnel test data base and the 1984 Outdoor Aerodynamic Research Facility (OARF) test data base. The objectives associated with the 80- by 120-Foot Wind Tunnel test data were to conduct data quality checks, obtain neural network representations, and demonstrate sensitivity to test conditions. The objectives associated with the OARF outdoor test data were to obtain a 'zero wind' neural network representation, and formulate and implement a neural network based wind correction procedure. An additional objective, common to both test data bases, was to conduct error comparisons. The conclusions from the present study were as follows: Compared to measured parameters (i.e., collective pitch angle), derived parameters (i.e., thrust coefficient) were found preferable as neural network inputs. For the 80- by 120-Foot Wind Tunnel test data base, the neural network based figure of merit representations did not extrapolate rotor stall. Using the OARF outdoor test database, a neural network based wind correction procedure was formulated and successfully implemented. Based on an error comparison, the present neural network based wind correction procedure was found to be more accurate compared to the existing, momentum-theory-based wind correction procedure. Also, a separate error comparison showed that the 80- by 120-Foot Wind Tunnel hover performance data were comparable to non-wind-corrected outdoor test data.

Kozapalli, S.↗
NASA NTRS1989

The free-wake prediction of rotor hover performance using a vortex embedding method

A method is developed to predict the rotor hover performance. This method solves the compressible mass conservation equation much like current full potential codes and can therefore predict the transonic flows on a rotor. However, the newly developed approach also allows for the free convection of shed vorticity and permits the computation of the entire hover wake system. The method uses a vortex embedding scheme in potential flow and has been implemented in a computer code, HELIX -I. To predict power we implement a simple boundary layer and two different induced-drag integration schemes. The induced-drag is obtained from surface pressure integration and an energy flux integral. Comparisons between computations and experiment show good agreement for the prediction of power polars, surface pressure distribution, and tip vortex geometry.

Ramachandran, K.↗
NASA NTRS2017

Measured Boundary Layer Transition and Rotor Hover Performance at Model Scale

An experiment involving a Mach-scaled, 11:08 f t: diameter rotor was performed in hover during the summer of 2016 at NASA Langley Research Center. The experiment investigated the hover performance as a function of the laminar to turbulent transition state of the boundary layer, including both natural and fixed transition cases. The boundary layer transition locations were measured on both the upper and lower aerodynamic surfaces simultaneously. The measurements were enabled by recent advances in infrared sensor sensitivity and stability. The infrared thermography measurement technique was enhanced by a paintable blade surface heater, as well as a new high-sensitivity long wave infrared camera. The measured transition locations showed extensive amounts, x=c>0:90, of laminar flow on the lower surface at moderate to high thrust (CT=s > 0:068) for the full blade radius. The upper surface showed large amounts, x=c > 0:50, of laminar flow at the blade tip for low thrust (CT=s < 0:045). The objective of this paper is to provide an experimental data set for comparisons to newly developed and implemented rotor boundary layer transition models in CFD and rotor design tools. The data is expected to be used as part of the AIAA Rotorcraft SimulationWorking Group

Overmeyer, Austin D.↗
NASA NTRS1989

Performance and loads data from an outdoor hover test of a Lynx tail rotor

A Lynx tail rotor was tested in hover at the Outdoor Aerodynamic Research Facility at NASA Ames Research Center. The test objectives were to measure the isolated rotor performance to provide a baseline for subsequent testing, and to operate the rotor throughout the speed and collective envelope before testing in the NFAC 40- by 80-Foot Wind Tunnel. Rotor forces and blade bending moments were measured at ambient wind conditions from zero to 6.23 m/sec. The test envelope was limited to rotor speeds of 1550 to 1850 rpm and minus 13 deg to plus 20 deg of blade collective pitch. The isolated rotor performance and blade loads data are presented.

Signor, David B.↗
NASA NTRSDate not supplied

Overview of Rotor Hover Performance Capabilities at Low Reynolds Number for Mars Exploration

The Evolutionary aLgorithm for Iterative Studies of Aeromechanics (ELISA) software was developed in support of the Rotorcraft Optimization for the Advancement of Mars eXploration (ROAMX) project. ELISA was developed to enable aerodynamic rotor hover optimization for low Reynolds number flows in the Mars atmosphere. ELISA comprises two modules. The first module is dedicated to airfoil optimization and allows for the creation of multi-objective Pareto optimal (PO) airfoil sets with the airfoil performance evaluation performed using OVERFLOW. The second module is dedicated to rotor hover performance optimization and generates multi-objective PO rotor sets with the rotor performance evaluation performed using the comprehensive analysis code CAMRAD II. This paper presents recent updates to the ELISA optimization toolset. The airfoil module now includes variation in section Reynolds number, alongside simultaneous maximization of section lift and minimization of section drag. Consequently, the rotor optimization module can query PO airfoil sets (as a function of section lift, drag, and Reynolds number) and generate PO C81 decks tailored to specific Reynolds numbers, eliminating the need for adequate initial chord guesses and allowing for arbitrary rotor solidities to be studied. Furthermore, the rotor optimization has been extended to incorporate a third dimension, alongside maximization of blade loading and minimization of rotor power. This enables optimization across a relevant density range on Mars, presenting the lowest power rotor hover geometry, for each attainable blade loading, for each density. The goal of this work is to present the relevance of recent updates to the ELISA optimization toolset, by showing full rotor hover optimization using unconventional airfoils across a practical Mars density range, and by presenting various optimizations for changing blade numbers with unconstrained solidity in the Mars atmosphere.

Rotor↗
NASA NTRS1990

Model tilt-rotor hover performance and surface pressure measurement

A test of a small scale 3-bladed model rotor, with geometry typical of that used on tilt rotor aircraft, was conducted in the Army Aeroflightdynamics Directorate's anechoic hover chamber. The purpose was to determine the hover performance of the rotor and investigate the pressure distributions on a blade at various collective pitch angles and tip speeds. The measured pressures indicate that the rotor did not stall for high collective pitch angles up to theta sub c = 25 deg. This is clearly a 3-D effect since 2-D theory predicts flow separation at these high angles. The flow near the trailing edge separated above theta sub c = 25 deg which caused a sharp increase in power.

Tung, Chee↗
NASA NTRS2004

Rotor Flapping Response to Active Control

Rotor active control using higher harmonic blade pitch has been proposed as a means to reduce both rotor radiated noise and airframe vibration and to enhance rotor performance. The higher harmonic input, however, can affect rotor thrust and cyclic flapping - the basic trim characteristics of the rotor. Some of the trim changes can negate the active control benefits. For example, wind tunnel test results of a full scale BO-105 rotor with individual-blade control indicate some rotor performance improvements, accompanied with changes in rotor trim, using two-per-rev blade pitch input. The observed performance benefits could therefore be a simple manifestation of the trim change rather than an efficient redistribution of the rotor airloads. More recently, the flight test of the BO-105 helicopter equip,ped with individual-blade-control actuators also reported trim changes whenever the two-per-rev blade pitch for noise reduction was activated. The pilot had to adjust the trim control to maintain the aircraft under a constant flight path. These two cases highlight the, importance of trim considerations in the application of active control to rotorcraft.

Nguyen, Khanh↗
NASA NTRS1982

Aerodynamic interactions between a 1/6 scale helicopter rotor and a body of revolution

A wind-tunnel investigation was conducted in which independent, steady state aerodynamic forces and moments were measured on a 2.24-m-diam, two bladed helicopter rotor and a body of revolution. The objective was to determine the interaction of the body on the rotor performance and the effect of the rotor on the body aerodynamics for variations in velocity, thrust, tip-path-plane angle of attack, body angle of attack, rotor/body position, and body nose geometry. Results show that a body of revolution near the rotor can produce significant favorable or unfavorable effects on rotor performance, depending on the operating condition. Body longitudinal aerodynamic characteristics are significantly modified by the presence of an operating rotor and hub.

Betzina, M. D.↗
NASA NTRS1982

Aerodynamic interactions between a 1/6-scale helicopter rotor and a body of revolution

A wind-tunnel investigation was conducted in which independent, steady-state aerodynamic forces and moments were measured on a 2.24-m-diam, two-bladed helicopter rotor and a body of revolution. The objective was to determine the interaction of the body on the rotor performance and the effect of the rotor on the body aerodynamics for variations in velocity, thrust, tip-path-plane angle of attack, rotor/body position, and body nose geometry. Results show that a body of revolution near the rotor can produce significant favorable or unfavorable effects on rotor performance, depending on the operating condition. Body longitudinal aerodynamic characteristics are significantly modified by the presence of an operating rotor and hub.

Betzina, M. D.↗
NASA NTRS2017

Impact of Wake Dispersion on Axial Compressor Performance

Rotor wake dispersion in a low-speed, one and half stage axial compressor is investigated in detail with a Large Eddy Simulation (LES). The primary focus is to quantify the total pressure recovery due to wake stretching and the total pressure loss from the rotor wake interaction with the stator blade boundary layer. The relative magnitude of the aerodynamic loss due to these two effects is examined at several radial locations. The spacing between the rotor and the stator was varied from 29% to 112% of the rotor axial chord at the mid span to investigate the effects of rotor wake decay before entering the stator passage. The current analysis indicates that the efficiency through the compressor stage is increased about 0.5% when the spacing between the rotor and the stator is decreased from 112% to 29% of the rotor axial chord at mid-span. 22% of the efficiency gain from the narrower axial gap is due to the wake recovery and 63% is due to the stronger unsteady pressure field at the exit of the rotor due to stage interaction. Total pressure loss/recovery across the stator varies significantly in the radial direction for the current compressor, which has a much lower aspect ratio. The total pressure recovery due to wake stretching is larger than the total pressure loss due to the unsteady boundary layer development on the stator blade from 20% to 35% of the span from the hub for 29% spacing and from 35% to 55% of the span for 112% spacing. Above 50% of the span, rotor tip clearance flow affects wake dispersion and the overall wake recovery is less than expected.

Axial Compressor↗
NASA NTRS2012

Application of a High-Fidelity Icing Analysis Method to a Model-Scale Rotor in Forward Flight

An icing analysis process involving the loose coupling of OVERFLOW-RCAS for rotor performance prediction and with LEWICE3D for thermal analysis and ice accretion is applied to a model-scale rotor for validation. The process offers high-fidelity rotor analysis for the noniced and iced rotor performance evaluation that accounts for the interaction of nonlinear aerodynamics with blade elastic deformations. Ice accumulation prediction also involves loosely coupled data exchanges between OVERFLOW and LEWICE3D to produce accurate ice shapes. Validation of the process uses data collected in the 1993 icing test involving Sikorsky's Powered Force Model. Non-iced and iced rotor performance predictions are compared to experimental measurements as are predicted ice shapes.

Narducci, Robert↗
NASA NTRSDate not supplied

Coaxial Rotor CFD Validation and ML Surrogate Model Generation

A fixed-pitch speed-controlled coaxial rotor system was tested in the NASA Langley Transonic Dynamics Tunnel in September 2022. The rotors have a diameter of 1.35 meters and an inter-rotor spacing of 25% of the diameter. Though this test was focused on the NASA New Frontiers Dragonfly mission, the resulting dataset is relevant to a wide array of applications of multirotor vehicles, especially those using fixed-pitch variable-speed rotors. Most notably beyond Dragonfly, perhaps, is the application of coaxial rotor pair configurations for eVTOL and Urban Air Mobility (UAM) aircraft. This work provides a thorough CFD validation study quantifying coaxial rotor performance estimation with accuracy on order 5-10% using an efficient hybrid BEMT-URANS flow solver over a wide range of operating conditions. This accuracy was achieved using novel approaches for the construction of both the C81 airfoil performance lookup tables and the BEMT rotor model. These novel approaches are combined with advanced scripting to further accelerate the commercial off-the-shelf CFD solver on GPU accelerated machines. Finally, the development of machine learning surrogate models is presented to produce highly efficient and accurate rotor performance predictions for fixed-pitch variable-speed multirotor aircraft over the complete flight regime including scout, cruise, climb, descent, as well as limiting cases of vortex-ring and windmill-brake states.

Coaxial↗
DOE OSTI2026

Power performance and loads characterization of laboratory-scale cross-flow rotors fabricated using additive manufacturing

Tidal energy conversion is a relatively new application for additive manufacturing (AM), where the focus has been on fabricating axial-flow turbine blades. AM techniques add material precisely where it is needed, creating more complex shapes with less waste. Cross-flow rotor geometry presents an opportunity for AM to improve rotor performance by fabricating features that cannot be created economically via conventional manufacturing. The challenges associated with using AM in cross-flow design include water resistance and degradation over time while retaining a level of quality equivalent to conventionally machined parts. In this work, AM materials were tested by environmentally conditioning samples in a seawater tank for 5 months, followed by performance and phase-resolved load testing of laboratory-scale rotors in a hydraulic flume. We found that while metals like titanium and Inconel have excellent performance in marine environments, achieving the desired geometry and performance is difficult. Thermoplastics degraded in seawater but were easier to form into desired geometries and could exceed the performance of an aluminum control rotor. Warping and surface finish were significant detractors from AM rotor performance. These results suggest that the primary benefits of using AM for cross-flow rotors is to quickly fabricate and test unconventional rotor geometries.

16 TIDAL AND WAVE POWER↗
NASA NTRS2012

Design and Performance of Lift-Offset Rotorcraft for Short-Haul Missions

The design and performance of compound helicopters utilizing lift-offset rotors are examined, in the context of short-haul, medium-size civil and military missions. The analysis tools used are the comprehensive analysis CAMRAD II and the sizing code NDARC. Following correlation of the comprehensive analysis with existing lift-offset aircraft flight test data, the rotor performance model for the sizing code was developed, and an initial estimate was made of the rotor size and key hover and cruise flight conditions. The rotor planform and twist were optimized for those conditions, and the sizing code rotor performance model updated. Two models for estimating the blade and hub weight of lift-offset rotors are discussed. The civil and military missions are described, along with the aircraft design assumptions. The aircraft are sized for 30 passengers or 6600 lb payload, with a range of 300 nm. Civil and military aircraft designs are described for each of the rotor weight models. Disk loading and blade loading were varied to optimize the designs, based on gross weight and fuel burn. The influence of technology is shown, in terms of rotor hub drag and rotor weight.

Johnson, Wayne↗
NASA NTRS1985

Aeroelastic considerations for torsionally soft rotors

A research study was initiated to systematically determine the impact of selected blade tip geometric parameters on conformable rotor performance and loads characteristics. The model articulated rotors included baseline and torsionally soft blades with interchangeable tips. Seven blade tip designs were evaluated on the baseline rotor and six tip designs were tested on the torsionally soft blades. The designs incorporated a systemmatic variation in geometric parameters including sweep, taper, and anhedral. The rotors were evaluated in the NASA Langley Transonic Dynamics Tunnel at several advance ratios, lift and propulsive force values, and tip Mach numbers. A track sensitivity study was also conducted at several advance ratios for both rotors. Based on the test results, tip parameter variations generated significant rotor performance and loads differences for both baseline and torsionally soft blades.

Mantay, W. R.↗