Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotor Tips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Experimental investigation of wingtip aerodynamic loading

An experimental investigation was performed to obtain the aerodynamic loading of a series of wingtips. The wingtips varied in taper ratio (1.0, 0.6, and 0.3) and in sweep angle (0, 20, 30, 35, and 45 deg). The wingtips were tested separately (wingtip only configuration) and while mounted on a semi-span wing. The quarter-chord sweep angle of the wing was varied from 30 deg forward sweep, to unswept, to 30 deg. aft sweep. Wingtip loading was obtained from a six component strainguage balance mounted in the wingtip. The effect of wing sweep and wingtip taper and wingtip sweep on the wingtip lift curve slope, drag polar, and pitching moment behavior is discussed. The obtained wingtip data was used to define blade tip platforms, suitable for use in the Free-Tip Rotor configuration. The Free-Tip Rotor has blade tips, which are allowed to weathervane into the blade tip's relative wind. A passive control moment is applied to the blade tip's pitch axis so as to cause blade tip motion around a prescribed null point providing a finite blade tip lift.

Van Aken, Johannes M.↗
NASA NTRS1994

Prediction of Unshsrouded Rotor Blade Tip Heat Transfer

The rate of heat transfer on the tip of a turbine rotor blade and on the blade surface in the vicinity of the tip, was successfully predicted. The computations were performed with a multiblock computer code which solves the Reynolds Averaged Navier-Stokes equations using an efficient multigrid method. The case considered for the present calculations was the Space Shuttle Main Engine (SSME) high pressure fuel side turbine. The predictions of the blade tip heat transfer agreed reasonably well with the experimental measurements using the present level of grid refinement. On the tip surface, regions with high rate of heat transfer was found to exist close to the pressure side and suction side edges. Enhancement of the heat transfer was also observed on the blade surface near the tip. Further comparison of the predictions was performed with results obtained from correlations based on fully developed channel flow.

Ameri, A. A.↗
NASA NTRS1987

Helicopter tail rotor blade-vortex interaction noise

A study is made of helicopter tail rotor noise, particularly that due to the interactions with main rotor tip vortices. Summarized here are present analysis, the computer codes, and the results of several test cases. Amiet's unsteady thin airfoil theory is used to calculate the acoustics of blade-vortex interaction. The noise source is modelled as a force dipole resulting from an airfoil of infinite span chopping through a skewed line vortex. To analyze the interactions between helicopter tail rotor and main rotor tip vortices, we developed a two-step approach: (1) the main rotor tip vortex system is obtained through a free wake geometry calculation of the main rotor using CAMRAD code; (2) acoustic analysis takes the results from the aerodynamic interaction analysis and calculates the farfield pressure signatures for the interactions. It is found that under a wide range of helicopter flight conditions, acoustic pressure fluctuations of significant magnitude can be generated by tail rotors due to a series of interactions with main rotor tip vortices. This noise mechanism depends strongly on the helicopter flight conditions and the relative location and phasing of the main and tail rotors. fluctuations of significant magnitude can be generated by tail rotors due to a series of interactions with main rotor tip vortices. This noise mechanism depends strongly upon the helicopter flight conditions and the relative location and phasing of the main and tail rotors.

George, Albert R.↗
NASA NTRS2017

Toward Understanding Tip Leakage Flows in Small Compressor Cores Including Stator Leakage Flow

The focus of this work was to provide additional data to supplement the work reported in NASA/CR-2015-218868 (Berdanier and Key, 2015b). The aim of that project was to characterize the fundamental flow physics and the overall performance effects due to increased rotor tip clearance heights in axial compressors. Data have been collected in the three-stage axial research compressor at Purdue University with a specific focus on analyzing the multistage effects resulting from the tip leakage flow. Three separate rotor tip clearances were studied with nominal tip clearance gaps of 1.5 percent, 3.0 percent, and 4.0 percent based on a constant annulus height. Overall compressor performance was previously investigated at four corrected speedlines (100 percent, 90 percent, 80 percent, and 68 percent) for each of the three tip clearance configurations. This study extends the previously published results to include detailed steady and time-resolved pressure data at two loading conditions, nominal loading (NL) and high loading (HL), on the 100 percent corrected speedline for the intermediate clearance level (3.0 percent). Steady detailed radial traverses of total pressure at the exit of each stator row are supported by flow visualization techniques to identify regions of flow recirculation and separation. Furthermore, detailed radial traverses of time-resolved total pressures at the exit of each rotor row have been measured with a fast-response pressure probe. These data were combined with existing three-component velocity measurements to identify a novel technique for calculating blockage in a multistage compressor. Time-resolved static pressure measurements have been collected over the rotor tips for all rotors with each of the three tip clearance configurations for up to five loading conditions along the 100 percent corrected speedline using fast-response piezoresistive pressure sensors. These time-resolved static pressure measurements reveal new knowledge about the trajectory of the tip leakage flow through the rotor passage. Further, these data extend previous measurements identifying a modulation of the tip leakage flow due to upstream stator wake propagation. Finally, a novel instrumentation technique has been implemented to measure pressures in the shrouded stator cavities. These data provide boundary conditions relating to the flow across the shrouded stator knife seal teeth. Moreover, the utilization of fast-response pressure sensors provides a new look at the time-resolved pressure field, leading to instantaneous differential pressures across the seal teeth. Ultimately, the data collected for this project represent a unique data set which contributes to build a better understanding of the tip leakage flow field and its associated loss mechanisms. These data will facilitate future engine design goals leading to small blade heights in the rear stages of high pressure compressors and aid in the development of new blade designs which are desensitized to the performance penalties attributed to rotor tip leakage flows.

Berdanier, Reid A.↗
NASA NTRS1978

An in-place recalibration technique to extend the temperature capability of capacitance-sensing, rotor-blade-tip-clearance measurement systems

It is known that capacitance-sensing, rotor-blade-tip-clearance measurement systems suffer from a strong dependency on probe tip temperature and humidity. A novel in-place recalibration technique partly overcomes this problem through a simple modification of the electronics that permits a scale factor correction. The technique is used to reduce the errors in a commercial system by more than 50 percent up to a temperature of 370 C (700 F). A probe design is proposed to further raise the maximum temperature capability of the measurement system.

Barranger, J.↗
NASA NTRS1977

Some results of the testing of a full-scale Ogee tip helicopter rotor; acoustics, loads, and performance

Full-scale tests were utilized to investigate the effect of the Ogee tip on helicopter rotor acoustics, performance, and loads. Two facilities were used for this study: the Langley whirl tower and a UH-1H helicopter. The test matrix for hover on the whirl tower involved thrust values from 0 to 44,480 N (10,000 lbs) at several tip Mach numbers for both standard and Ogee rotors. The full-scale testing on the UH-1H encompassed the major portion of the flight envelope for that aircraft. Both near-field acoustic measurements as well as far-field flyover data were obtained for both the Ogee and standard rotors. Data analysis of the whirl-tower test shows that the Ogee tip does significantly diffuse the tip vortex while providing some improvement in hover performance. Flight testing of both rotors indicates that the strong impulsive noise signature of the standard rotor can be reduced with the Ogee rotor. Forward flight performance was significantly improved with the Ogee configuration for a large number of flight conditions. Further, rotor control loads and vibrations were reduced through use of this advanced tip rotor.

Mantay, W. R.↗
NASA NTRS2000

A Novel Method for Reducing Rotor Blade-Vortex Interaction

One of the major hindrances to expansion of the rotorcraft market is the high-amplitude noise they produce, especially during low-speed descent, where blade-vortex interactions frequently occur. In an attempt to reduce the noise levels caused by blade-vortex interactions, the flip-tip rotor blade concept was devised. The flip-tip rotor increases the miss distance between the shed vortices and the rotor blades, reducing BVI noise. The distance is increased by rotating an outboard portion of the rotor tip either up or down depending on the flight condition. The proposed plan for the grant consisted of a computational simulation of the rotor aerodynamics and its wake geometry to determine the effectiveness of the concept, coupled with a series of wind tunnel experiments exploring the value of the device and validating the computer model. The computational model did in fact show that the miss distance could be increased, giving a measure of the effectiveness of the flip-tip rotor. However, the wind experiments were not able to be conducted. Increased outside demand for the 7'x lO' wind tunnel at NASA Ames and low priority at Ames for this project forced numerous postponements of the tests, eventually pushing the tests beyond the life of the grant. A design for the rotor blades to be tested in the wind tunnel was completed and an analysis of the strength of the model blades based on predicted loads, including dynamic forces, was done.

Glinka, A. T.↗
NASA NTRS1986

Helicopter tail rotor noise analyses

A study was made of helicopter tail rotor noise, particularly that due to interactions with the main rotor tip vortices, and with the fuselage separation mean wake. The tail rotor blade-main rotor tip vortex interaction is modelled as an airfoil of infinite span cutting through a moving vortex. The vortex and the geometry information required by the analyses are obtained through a free wake geometry analysis of the main rotor. The acoustic pressure-time histories for the tail rotor blade-vortex interactions are then calculated. These acoustic results are compared to tail rotor loading and thickness noise, and are found to be significant to the overall tail rotor noise generation. Under most helicopter operating conditions, large acoustic pressure fluctuations can be generated due to a series of skewed main rotor tip vortices passing through the tail rotor disk. The noise generation depends strongly upon the helicopter operating conditions and the location of the tail rotor relative to the main rotor.

George, A. R.↗
NASA NTRS1986

Helicopter tail rotor noise

A study was made of helicopter tail rotor noise, particularly that due to interactions with the main rotor tip vortices, and with the fuselage separation mean wake. The tail rotor blade-main rotor tip vortex interaction is modelled as an airfoil of infinite span cutting through a moving vortex. The vortex and the geometry information required by the analyses are obtained through a free wake geometry analysis of the main rotor. The acoustic pressure-time histories for the tail rotor blade-vortex interactions are then calculated. These acoustic results are compared to tail rotor loading and thickness noise, and are found to be significant to the overall tail rotor noise generation. Under most helicopter operating conditions, large acoustic pressure fluctuations can be generated due to a series of skewed main rotor tip vortices passing through the tail rotor disk. The noise generation depends strongly upon the helicopter operating conditions and the location of the tail rotor relative to the main rotor.

Chou, S.-T.↗
NASA NTRS2012

The Effect of Rotor Cruise Tip Speed, Engine Technology and Engine/Drive System RPM on the NASA Large Civil Tiltrotor (LCTR2) Size and Performance

A multi-year study was conducted under NASA NNA06BC41C Task Order 10 and NASA NNA09DA56C task orders 2, 4, and 5 to identify the most promising propulsion system concepts that enable rotor cruise tip speeds down to 54% of the hover tip speed for a civil tiltrotor aircraft. Combinations of engine RPM reduction and 2-speed drive systems were evaluated. Three levels of engine and the drive system advanced technology were assessed; 2015, 2025 and 2035. Propulsion and drive system configurations that resulted in minimum vehicle gross weight were identified. Design variables included engine speed reduction, drive system speed reduction, technology, and rotor cruise propulsion efficiency. The NASA Large Civil Tiltrotor, LCTR, aircraft served as the base vehicle concept for this study and was resized for over thirty combinations of operating cruise RPM and technology level, quantifying LCTR2 Gross Weight, size, and mission fuel. Additional studies show design sensitivity to other mission ranges and design airspeeds, with corresponding relative estimated operational cost. The lightest vehicle gross weight solution consistently came from rotor cruise tip speeds between 422 fps and 500 fps. Nearly equivalent results were achieved with operating at reduced engine RPM with a single-speed drive system or with a two-speed drive system and 100% engine RPM. Projected performance for a 2025 engine technology provided improved fuel flow over a wide range of operating speeds relative to the 2015 technology, but increased engine weight nullified the improved fuel flow resulting in increased aircraft gross weights. The 2035 engine technology provided further fuel flow reduction and 25% lower engine weight, and the 2035 drive system technology provided a 12% reduction in drive system weight. In combination, the 2035 technologies reduced aircraft takeoff gross weight by 14% relative to the 2015 technologies.

Robuck, Mark↗
NASA NTRS2014

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size On the Tip Clearance Flow Structure at Near Stall Operation - Part 2

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Unsteady↗
NASA NTRS2010

Summary of the Large Civil Tiltrotor (LCTR2) Engine Gearbox Study

In support of the Fundamental Aeronautics Program, Subsonic Rotary Wing Project, NASA is continuing to study the Large Civil Tiltrotor (LCTR) concept to help define/refine vehicle, system and subsystem attributes. These attributes can then be used to define performance requirements and identify new or advanced technologies to achieve an operational vehicle class. As part of this goal, NASA contracted with The Boeing Company and its subcontractor Rolls-Royce to perform an investigation of different combinations of engine and gearbox variability to achieve a maximum of 50 percent rotor tip speed reduction from hover to cruise conditions. Previous NASA studies identified the 50 percent rotor speed reduction minimized vehicle gross weight and fuel burn. The LCTR2 (LCTR-iteration 2) was the contracted study baseline for initial sizing. Rotor tip speed ratios (cruise to hover) of 100, 77, and 54 percent were analyzed for each combination of engine and gearbox speed reduction to achieve the chosen rotor tip speed ratio. Three different engine and gearbox technology levels were assumed; commercial off-the-shelf (COTS), entry-in-service (EIS) in 2025 and EIS in 2035. These technology levels were applied to determine each particular effect on vehicle gross weight and fuel burn, while other vehicle technologies were assumed constant. This report summarizes the work performed that is being put together into a comprehensive NASA contractor report. Some background on the LCTR concept and baseline vehicle will be given and then a discussion concerning the technical approach utilized. Major study assumptions and results will be presented and discussed. Finally conclusions will be drawn as well as suggestions provided for future efforts.

Snyder, Christopher A.↗
NASA NTRS1983

Comparison of calculated and measured pressures on straight and swept-tip model rotor blades

Using the quasi-steady, full potential code, ROT22, pressures were calculated on straight and swept tip model helicopter rotor blades at advance ratios of 0.40 and 0.45, and into the transonic tip speed range. The calculated pressures were compared with values measured in the tip regions of the model blades. Good agreement was found over a wide range of azimuth angles when the shocks on the blade were not too strong. However, strong shocks persisted longer than predicted by ROT22 when the blade was in the second quadrant. Since the unsteady flow effects present at high advance ratios primarily affect shock waves, the underprediction of shock strengths is attributed to the simplifying, quasi-steady, assumption made in ROT22.

Tauber, M. E.↗
NASA NTRS1980

Fuel conservation through active control of rotor clearances

Under the NASA-sponsored Energy Efficient Engine (EEE) Project, technology is being developed which will significantly reduce the fuel consumption of turbofan engines for subsonic transport aircraft. One technology concept being pursued is active control of rotor tip clearances. Attention is given to rotor tip clearance considerations and an overview of preliminary study results as well as the General Electric EEE clearance control approach is presented. Finally, potential fuel savings with active control of rotor clearances for a typical EEE mission are predicted.

Beitler, R. S.↗
NASA NTRS1985

Wide-field shadowgraph flow visualization of tip vortices generated by a helicopter rotor

The vortex trajectory and vortex wake generated by helicopter rotors were visualized using a wide-field shadowgraph technique. Use of a retro-reflective Scotchlite screen made it possible to investigate the flow field generated by full-scale tail rotors. Tip vortex trajectories were visible in shadowgraphs for a range for tip Mach number of 0.38 - 0.60. The effect of the angle of attack was substantial. At an angle of attack greater than 8 degrees, the visibility of the vortex core was significant even at relatively low tip Mach numbers. The theoretical analysis of the visibility was carried out for a rotating blade. This analysis demonstrated that the visibility decreases with increasing dimensionless core radius (ro/c) and increases with increasing tip Mach number. Based on this investigation, it is concluded that the wide-field shadowgraph flow visualization technique should be feasible to study the flow field generated by a large main rotor in a wind tunnel and in an outdoor full-scale test stand. Of note is that the shadowgraph technique could easily be used with other on-going tests such as aerodynamic performance study, noise measurements, velocity measurements with LDV or hot-wire anemometer, local pressure measurement on the rotor surface, etc.

Parthasarathy, S. P.↗
NASA NTRS1980

Teetered, tip-controlled rotor: Preliminary test results from Mod-0 100-kW experimental wind turbine

Results of tests conducted using the MOD-0 100 kW experimental wind turbine are evaluated. The teetered rotor significantly decreased loads on the yaw drive mechanism and reduced blade cyclic flapwise bending moments by 25 percent at the 20 percent span location when compared to the rigid hub rotor. The teetered hub performed well, but impacted the teeter stops on occasion as wind speed and/or direction varied rapidly. The tip-controlled rotor performed satisfactorily with some expected loss of control when compared to the full span pitchable blade. The performance results indicate that a review of techniques used to calculate rotor power is in order.

Glasgow, J. C.↗
NASA NTRS1996

Analysis of Gas Turbine Rotor Blade Tip and Shroud Heat Transfer

Predictions of the rate of heat transfer to the tip and shroud of a gas turbine rotor blade are presented. The simulations are performed with a multiblock computer code which solves the Reynolds Averaged Navier-Stokes equations. The effect of inlet boundary layer thickness as well as rotation rate on the tip and shroud heat transfer is examined. The predictions of the blade tip and shroud heat transfer are in reasonable agreement with the experimental measurements. Areas of large heat transfer rates are identified and physical reasoning for the phenomena presented.

Ameri, A. A.↗