SEARCH · Search NASA

Results for “START”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Start-stop testing of two self-acting air-lubricated spiral groove thrust bearing coatings

Start-stop tests were conducted on air-lubricated spiral-groove thrust bearings. Application of a matrix-bonded molybdenum disulfide (MoS2) coating over a porous chrome oxide coating resulted in significantly lower friction, compared to bearings coated with chrome oxide only. The MoS2 coated bearing sustained 15,000 start-stop cycles at a maximum of 3600 rpm. Each cycle was 15 seconds on, 30 seconds off. The chrome oxide coated bearing failed by local welding after 2030 cycles. Both types of coatings exhibited early failures under higher thrust loads when operating films were insufficient to sustain the load without overheating.

Dunfee, J. D.↗

NASA NTRS1978

An investigation of the side force that is sometimes observed in rocket start-up

The occurrence of a large but momentary side force during the start-up of rocket motors employing convergent-divergent nozzles has been noted occasionally. Asymmetric flow separation within the divergent section of the nozzle is proposed as the principal source of this lateral force. A method for estimating this force and its concomitant lateral impulse is outlined, and results obtained by applying the method to Scout vehicle first-, second-, and third-stage rocket motor start-ups are presented and compared with similar estimates that other researchers obtained by a different method.

Bowyer, J. M., Jr.↗

NASA NTRS1980

Effect of starting powder characteristics on density, microstructure and low temperature oxidation behavior of a Si3N48w/o Y2O3 ceramic

The densification and oxidation behavior of Si3N4 - 8w/oY2O3 prepared from three commercial starting powders were studied. Bars of SN 402, SN 502, and CP 85/15 were sintered for 3 to 4.5 hours at 1750 C. A second set was hot pressed for 2 hours at 1750 C. The microstructures were studied by transmission electron microscopy and scanning electron microscopy, densities were determined, and the phase compositions were determined by X-ray diffraction. Densification and microstructure were greatly influenced by the starting powder morphology and impurity content. Although SN 402 exhibited the maximum weight lose, the highest sintered and hot pressed densities were obtained with this powder. All powders had both equiaxed and elongated grains. Sintered bars were composed of beta silicon nitride and n-melelite. In contrast, hot pressed bars contained beta silicon nitride, H-phase, and J-phase, but no melelite. Yttria distribution in sintered bars was related to the presence of cation impurities such as Ca, Fe, and Mg. A limited oxidation study at 750 C in air showed no instability in these Si3N4 - 8 w/oY2O3 specimens, regardless of startin powder.

Schuon, S.↗

NASA NTRS1984

Starting Silicon-Ribbon Growth Automatically

Semiautomatic system starts growth of silicon sheets more reliably than system with purely manual control. Control signals for starting sheetcrystal growth consist of ramps (during which signal changes linearly from one value to another over preset time interval) and soaks (during which signal remains constant). Ramps and soaks for best temperature and pulling speed determined by experimentation.

Mchugh, J. P.↗

NASA NTRS1983

Alcohol cold starting - A theoretical study

Two theoretical computer models have been developed to study cold starting problems with alcohol fuels. The first model, a droplet fall-out and sling-out model, shows that droplets must be smaller than 50 microns to enter the cylinder under cranking conditions without being slung-out in the intake manifold. The second model, which examines the fate of droplets during the compression process, shows that the heat of compression can be used to vaporize small droplets (less than 50 microns) producing flammable mixtures below freezing ambient temperatures. While droplet size has the greater effect on startability, a very high compression ratio can also aid cold starting.

Browning, L. H.↗

NASA NTRS1986

A study of starting time in great hard X-ray flares

An analysis of the starting time in ten great hard X-ray bursts observed with the X-Ray Burst Spectrometer (HXRBS) is presented. It is shown that the impulsive phase of nine of them is composed of a preflash phase, during which the burst is observed up to an energy limit ranging from some tens of keV to 200 keV, followed ten to some tens of seconds afterwards by a flash phase, where the count rate rises simultaneously in all detector channels. For two events strong gamma-ray line emission is observed and is shown to start close to the onset of the flash phase.

Klein, K. L.↗

NASA NTRS1988

Propagation of vortex rings and starting plumes in high and low g

The propagation of vortex rings and starting plumes during crystal growth in supercooled solutions was investigated in variable gravity environment created by acceleration-deceleration routine of a NASA's KC-135 flight. A specially designed crystal growth cell was used to study convection around crystals growing in supersaturated solutions of Na2SO4 and NaCl aboard the NASA KC-135. The results of vertical velocity measurements have shown that a continuously fed plume attains a higher velocity than the individual vortex ring. The results also indicated that the vortex ring decelerates as it propagates, and slows down much more rapidly than the starting plume, indicating a less efficient transport. It is suggested that inertial effects and buoyancy effects on vortex and plume propagation can be separated in the controlled environment of a Space Station borne centrifuge.

Hallett, J.↗

NASA NTRS1990

Applicability and evaluation of an implicit self-starting unconditionally stable methodology for the dynamics of structures

The applicability and evaluation of a new self-starting, unconditionally stable, implicit methodology of computation for the dynamics of structures is described. The methodology offers different perspectives and architecture for structural dynamics compared with the traditional (widely advocated and commonly used) time integration methods. It is based on velocity representations and architecture and uses finite elements as the principal analysis tool for structural dynamic modeling/analysis. In particular, the dynamics of beam-type flexural models are considered, and comparative results validate and support the proposed use of the self-starting methodology of computation for the dynamics of linear/nonlinear structures. The overall effectiveness and elegance strongly support its use in most existing commercial codes.

Tamma, Kumar K.↗

NASA NTRS1992

A new explicit variable time-integration self-starting methodology for computational structural dynamics

A new explicit variable time-integration methodology and architecture which possesses self-starting attributes, eliminates the need to involve acceleration computations, and which has improved accuracy characteristics in comparison to the traditional central-difference-type formulations customarily advocated is described for applicability to computational structural dynamics. To sharpen the focus of the present study, an explicit variable time-integration architecture which is relatively simple, yet effective, is described. Unlike variable explicit time-integration formulations adopted in the past, the present self-starting variable time-integration architecture and implementation aspects facilitate a simplified representation and a straightforward and effective approach for combining finite element meshes requiring different time steps in a single analysis. Numerical test cases are provided which demonstrate the applicability of the proposed formulations.

Tamma, Kumar K.↗

NASA NTRS1954

Starting characteristics and combustion performance of magnesium slurry in 6.5-inch-diameter ram-jet engine mounted in connected-pipe facility

The starting characteristics and combustion performance of slurry type fuels, consisting of 50 percent magnesium powder in a hydrocarbon carrier, have been investigated in a flight-type, 6.5-inch-diameter ram-jet engine in a connected-pipe facility. Quick, dependable starting of the engine was obtained by the use of a disk which blocked part of the combustor area downstream of the flame holder. Acceptable performance was achieved with a short fuel-air mixing length by the development of a fuel-distribution control sleeve.

COMBUSTION - RAM-JET ENGINES↗

NASA NTRS1956

Analysis of turbojet-engine controls for afterburning starting

A simulation procedure is developed for studying the effects of an afterburner start on a controlled turbojet engine. The afterburner start is represented by introducing a step decrease in the effective exhaust-nozzle area, after which the control returns the controlled engine variables to their initial values. The degree and speed with which the control acts are a measure of the effectiveness of the particular control system. Data are presented from five systems investigated using an electronic analog computer and the developed simulation procedure. These systems are compared with respect to steady-state errors, speed of response, and transient deviations of the system variables.

Phillips, W E , Jr↗

NASA NTRS1926

A study of the effect of a diving start on airplane speed

Equations for instantaneous velocity and distance flown are derived for an airplane which crosses the starting line of a speed course at a speed higher than that which can normally be maintained in horizontal flight. A specific case is assumed and calculations made for five initial velocities. Curves of velocity, average velocity, and distance flown are plotted against time for each case and analyzed. It is shown that the increase in average velocity due to a diving start may be very large for short-speed courses.

Diehl, Walter S↗

NASA NTRS1997

Space Shuttle Main Engine Start with Off-Nominal Propellant Inlet Pressures

This paper describes Rocketdyne's successful analysis and demonstration of the Space Shuttle Main Engine (SSME) operation at off-nominal propellant inlet conditions during the Reusable Launch Vehicle (RLV) evaluation tests. The nominal inlet condition range is: 103 to 111 psia and 170.5 to 178 deg. R for the oxidizer and 43 to 47 psia and 37 to 40 deg. R for the fuel. The SSME start was successfully demonstrated with engine inlet pressures of 50 psia liquid oxygen (LOX) with subcooled LOX at 160 deg R and 38 psia fuel at 38 deg. R. Four tests were used to incrementally modify the start sequence to demonstrate the final goal.

Bradley, Michael↗

NASA NTRS1996

Impulsive Start of a Symmetric Airfoil at High Angle of Attack

The fluid dynamic phenomena following the impulsive start of a NACA 0015 airfoil were studied by using a time accurate solution of the incompressible laminar Navier-Stokes equations. Angle of attack was set at 10 deg to simulate steady-state poststall conditions at a Reynolds number of 1.2 x 10(exp 4). The calculation revealed that large initial lift values can be obtained, immediately following the impulsive start, when a trapped vortex develops above the airfoil. Before the buildup of this trapped vortex and immediately after the airfoil was set into motion, the fluid is attached to the airfoil's surface and flows around the trailing edge, demonstrating the delay in the buildup of the classical Kutta condition. The transient of this effect is quite short and is followed by an attached How event that leads to the trapped vortex that has a longer duration. The just described initial phenomenon eventually transits into a fully developed separated flow pattern identifiable by an alternating, periodic vortex shedding.

Katz, Joseph↗

NASA NTRS1992

Operationally Efficient Propulsion System Study (OEPSS) Data Book: Integrated Booster Propulsion Module (BPM) Engine Start Dynamics - Volume 8

A fluid-dynamic, digital-transient computer model of an integrated, parallel propulsion system was developed for the CDC mainframe and the SUN workstation computers. Since all STME component designs were used for the integrated system, computer subroutines were written characterizing the performance and geometry of all the components used in the system, including the manifolds. Three transient analysis reports were completed. The first report evaluated the feasibility of integrated engine systems in regards to the start and cutoff transient behavior. The second report evaluated turbopump out and combined thrust chamber/turbopump out conditions. The third report presented sensitivity study results in staggered gas generator spin start and in pump performance characteristics.

Kemp, Victoria R.↗

NASA NTRS1998

Start Up of a Nb-1%Zr Potassium Heat Pipe From the Frozen State

The start up of a liquid metal heat pipe from the frozen state was evaluated experimentally with a Nb-1%Zr heat pipe with potassium as the working fluid. The heat pipe was fabricated and tested at Los Alamos National Laboratory. RF induction heating was used to heat 13 cm of the 1-m-long heat pipe. The heat pipe and test conditions are well characterized so that the test data may be used for comparison with numerical analyses. An attempt was made during steady state tests to calibrate the heat input so that the heat input would be known during the transient cases. The heat pipe was heated to 675 C with a throughput of 600 W and an input heat flux of 6 W/cm(exp 2). Steady state tests, start up from the frozen state, and transient variations from steady state were performed.

Glass, David E.↗

NASA NTRS1997

Heat Treatments of ZnSe Starting Materials for Physical Vapor Transport

The effect of different heat treatments on stoichiometry and residual gas pressure in ZnSe physical vapor transport system was investigated. The dependence of the amount and composition of the residual gas on various heat treatment procedures is reported. Heat treatment of ZnSe starting materials by baking under the condition of dynamic vacuum to adjust its stoichiometry was performed and the effectiveness of the treatment was confirmed by the measurements of the partial pressure of Se2, P(sub Se2), in equilibrium with the heat treated samples. Optimum heat treatment procedures on the ZnSe starting material for the physical vapor transport process are discussed and verified experimentally.

Su, Ching-Hua↗

NASA NTRS1998

Heat Treatments of ZnSe Starting Materials for Physical Vapor Transport

Su, Ching-Hua↗