Search NASA⌕ Search

SEARCH · Search NASA

Results for “SURFACE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Wing force and surface pressure data from a hover test of a 0.658-scale V-22 rotor and wing

A hover test of a 0.658-scale V-22 rotor and wing was conducted in the 40 x 80 foot wind tunnel at Ames Research Center. The principal objective of the test was to measure the surface pressures and total download on a large scale V-22 wing in hover. The test configuration consisted of a single rotor and semispan wing on independent balance systems. A large image plane was used to represent the aircraft plane of symmetry. Wing flap angles ranging from 45 to 90 degrees were examined. Data were acquired for both directions of the rotor rotation relative to the wing. Steady and unsteady wing surface pressures, total wing forces, and rotor performance data are presented for all of the configurations that were tested.

Felker, Fort F.↗
NASA NTRS1984

An experimental study of the properties of surface pressure fluctuations in strong adverse pressure gradient turbulent boundary layers

Experimental data were obtained on blade self-noise generation by strong adverse-pressure-gradient attached boundary layers and by separated turbulent boundary layers that accompany stall. Two microphones were calibrated, placed in plastic housing, and installed in a wind tunnel where observations of acoustic and turbulent signals permitted decomposition of the surface pressure fluctuation signals into the propagated acoustic part and the turbulent-flow generated portion. To determine the convective wave speed of the turbulent contributions, the microphones were spaced a small distance apart in the streamwise direction and correlations were obtained. The turbulent surface pressure spectra upstream of detachment and downstream of the beginning of separation are discussed as well as measurements of turbulent velocity spectra and wavespeeds.

Simpson, R. L.↗
NASA NTRS1971

Boundary layer transition detection on the X-15 vertical fin using surface-pressure-fluctuation measurements

A flush-mounted microphone on the vertical fin of an X-15 airplane was used to investigate boundary layer transition phenomenon during flights to peak altitudes of approximately 70,000 meters. The flight results were compared with those from wind tunnel studies, skin temperature measurements, and empirical prediction data. The Reynolds numbers determined for the end of transition were consistent with those obtained from wind tunnel studies. Maximum surface-pressure-fluctuation coefficients in the transition region were about an order of magnitude greater than those for fully developed turbulent flow. This was also consistent with wind tunnel data. It was also noted that the power-spectral-density estimates of the surface-pressure fluctuations were characterized by a shift in power from high frequencies to low frequencies as the boundary layer changed from turbulent to laminar flow. Large changes in power at the lowest frequencies appeared to mark the beginning of transition.

Lewis, T. L.↗
NASA NTRSDate not supplied

Surface Pressure Results for the NATO AVT-298 SWiFT Configuration in the National Transonic Facility

A high Reynolds number wind tunnel test of the Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objective of the test was to investigate Reynolds number scaling effects on the low-speed stability & control characteristics of the SWiFT model. Surface pressure results corroborate the force & moment results and help to provide more insight into the observed flow behavior. The effect of angle of attack and Reynolds number on the low-speed surface pressure results are analyzed particularly around the leading edge of the model. The onset and progression of flow separation on the wings particularly near the wing crank is also investigated, as well as the cause of an observed double-stall behavior. Finally, the transonic results showed a slight forward movement of the shock location with decreased shock strength as Reynolds number was increased. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

NATO AVT-298↗
NASA NTRSDate not supplied

Surface Pressure Results for the NATO AVT-298 SWiFT Configuration in the National Transonic Facility

A high Reynolds number wind tunnel test of the Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objective of the test was to investigate Reynolds number scaling effects on the low-speed stability & control characteristics of the SWiFT model. Surface pressure results corroborate the force & moment results and help to provide more insight into the observed flow behavior. The effect of angle of attack and Reynolds number on the low-speed surface pressure results are analyzed particularly around the leading edge of the model. The onset and progression of flow separation on the wings particularly near the wing crank is also investigated, as well as the cause of an observed double-stall behavior. Finally, the transonic results showed a slight forward movement of the shock location with decreased shock strength as Reynolds number was increased. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

NATO AVT-298↗
NASA NTRS1968

The surface pressure of Venus

Mechanical and microwave model atmospheres to obtain Venus surface pressure and temperature distribution

Gray, L. D.↗
NASA NTRS1959

Flow Characteristics About Two Thin Wings of Low Aspect Ratio Determined from Surface Pressure Measurements Obtained in Flight at Mach Numbers from 0.73 to 1.90

Surface pressure measurements were obtained at three chordwise stations on the wings of the X-3 and X-lE airplanes at Mach numbers from 0.73 to 1.13 for the X-3, and from 0.82 to 1.90 for the X-IE. Leading-edge separation is present on the X-3 wing at a Mach number of about 0.73 and an angle of attack of about 6 deg. However., when the Mach number is increased to 0.88, the trailing-edge separation dominates the pressure distribution and no leading-edge separation is visible although it is anticipated at the higher angles of attack shown. Conversely, the X-lE wing shows no indication of leading-edge separation within the scope of this investigation, but an overexpansion immediately behind the leading edge is present at a Mach number of approximately 0.82. Two separate normal shocks are present on the X-3 wing at a Mach number of about 0.88 and at a low angle of attack as an effect of wing geometry. These shocks merge to form a single shock when the angle of attack is increased to about 6 deg. At supersonic speeds the upper-surface expansion on the X-lE wing is limited by the approach of the pressure coefficients to the pressure coefficient for a vacuum.

Taillon, Norman V.↗
NASA NTRS1986

Comparison of experimental surface pressures with theoretical predictions on twin two-dimensional convergent-divergent nozzles

A three-dimensional subsonic aerodynamic panel code (VSAERO) was used to predict the effects of upper and lower external nozzle flap geometry on the external afterbody/nozzle pressure coefficient distributions and external nozzle drag of nonaxisymmetric convergent-divergent exhaust nozzles having parallel external sidewalls installed on a generic twin-engine high performance aircraft model. Nozzle static pressure coefficient distributions along the upper and lower surfaces near the model centerline and near the outer edges (corner) of the two surfaces were calculated, and nozzle drag was predicted using these surface pressure distributions. A comparison between the theoretical predictions and experimental wind tunnel data is made to evaluate the utility of the code in calculating the flow about these types of non-axisymmetric afterbody configurations. For free-stream Mach numbers of 0.60 and 0.90, the conditions where the flows were attached on the boattails yielded the best comparison between the theoretical predictions and the experimental data. For the Boattail terminal angles of greater than 15 deg., the experimental data for M = 0.60 and 0.90 indicated areas of separated flow, so the theoretical predictions failed to match the experimental data. Even though calculations of regions of separated flows are within the capabilities of the theoretical method, acceptable solutions were not obtained.

Carlson, J. R.↗
NASA NTRSDate not supplied

Steady Surface Pressure Measurement via the Lifetime Method With High-Speed Cameras in NASA's Unitary Plan Wind Tunnel

High spatial resolution measurement of steady surface pressure via pressure-sensitive paint at NASA Ames has traditionally relied on specialized cameras equipped to accumulate charge over multiple exposures, whereas measurement of the fluctuating component of pressure uses an altogether separate set of high-speed cameras. To reduce complexity of installation, data acquisition, and processing, we have implemented methods to use a single set of commercial off-the-shelf cameras to produce both steady and unsteady pressure measurements. Both imaging systems were installed in the 11-by 11-foot NASA Ames Unitary Plan Wind Tunnel and acquired images of a scaled model of the Space Launch System Block 1B Crew and Cargo configurations over a variety of flow conditions. This work focuses on methods for data acquisition, processing, and calibration to produce steady-state pressure estimates on the surface of the wind tunnel model based on the lifetime method. It will then compare the steady solutions produced by the legacy and high-speed imaging systems.

Pressure Sensitive Paint↗
NASA NTRS1977

Film cooling on the pressure surface of a turbine vane

Film-cooling-air ejection from the pressure surface of a turbine vane was investigated, and experimental data are presented. This investigation was conducted in a four-vane cascade on a J75-size turbine vane that had a double row of staggered holes in line with the primary flow and located downstream of the leading edge region. The results showed that: (1) the average effectiveness of film-convection cooling was higher than that of either film cooling or convection cooling separately; (2) the addition of small quantities of film-cooling air always increased the cooling effectiveness relative to the zero-injection case; however, (3) the injected film must exceed a certain threshold value to obtain a beneficial effect of film cooling relative to convection cooling alone.

Gauntner, J. W.↗
NASA NTRS1989

Construction of surface pressure field from scatterometer wind field

An account of the construction of surface pressure fields from Seasat-A satellite scatterometer (SASS) winds as carried out by different methods, and the comparison of these pressure fields with those derived from in situ ship observations is presented. On the assumption that the pressure adjusts itself instantaneously to the motion field, it may be computed by various methods. One of these makes use of planetary boundary theory, and of the possible techniques in this category a two-layer iterative scheme admitting of the parametrization of diabatic and baroclinic effects and of secondary flow was chosen. A second method involves the assumption of zero two-dimensional divergence, leading to a Laplace's equation (the balance equation) in pressure, with the wind field serving as a forcing function. This method does not accommodate adiabatic or baroclinic effects, and requires a knowledge of the pressure at all boundary points. Two comparison fields are used for validation: the conventional operational analyses of the US National Meteorological Center (NMC), and the special analyses of the Gulf of Alaska Experiment (GOASEX), which were done by hand. The results of the computations were as follows: (1) The pressure fields, as computed from the SASS winds alone, closely approximated the NMC fields in regions where reasonable in situ coverage was available (typically, one or two mb differences over most of the chart, three to four mb in extreme cases); (2) In some cases the SASS-derived pressure fields displayed high-resolution phenomena not detected by the NMC fields, but evident in the GOASEX data; and, (3) As expected, the pressure fields derived from the balance equation were much smoother and less well resolved than the SASS-derived or NMC fields. The divergence as measured from the SASS winds is smaller than, but of the same order of magnitude as, the vorticity.

Wurtele, Morton G.↗
NASA NTRS1986

Surface pressure measurement during low speed two-dimensional blade-vortex interaction

Unsteady blade surface pressures were measured during two-dimensional blade-vortex interaction. A periodically generated vortex filament interacted with a blade model instrumented over the first 20 percent of the blade surface. Analysis of data confirm the leading edge nature of BVI and show the amplitude of the interaction to be a strong function of blade-to-vortex spacing. Lift perturbation time histories were computed and are used to examine details of the encounter process.

Booth, E. R., Jr.↗
NASA NTRS1989

Heat-transfer and surface-pressure measurements for the SSME fuel-side turbopump turbine

Detailed heat flux and surface pressure distribution on the first-stage vane and blade of the Space Shuttle Main Engine fuel side turbopump turbine are examined. The specific turbine being utilized for the study is a combination of actual engine hardware and reproduced hardware consistent with that being used at NASA-Marshall for the initial measurements in their newly constructed blow-down turbine test facility. The facility is of the short duration shock tunnel variety, which permits use of thin film thermometers which are used to measure the surface temperature histories at prescribed locations on the turbine component parts. Heat flux values are then inferred from the temperature histories using standard data reduction procedures. The measurement program is described in detail.

Dunn, Michael G.↗
NASA NTRS1987

Surface pressure fluctuations in a separating turbulent boundary layer

A novel, microphone-employing technique for the measurement of pressure fluctuations through pinhole apertures in the flow surface is used in the present study of separating boundary layer pressure fluctuation spectra and wavespeeds. The rms of the surface pressure fluctuation increases monotonically through the adverse-pressure gradient attached flow region and the detached flow zone. A correlation of the detached flow data is given which is derived from velocity and length scales of the separated flow. The celerity of the surface pressure fluctuations for the attached flow increases with frequency to a maximum, and the streamwise coherence decreases drastically after the begining of flow reversal.

Simpson, Roger L.↗