Search NASA⌕ Search

SEARCH · Search NASA

Results for “SWELLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Effect of defect imbalance on void swelling distributions produced in pure iron irradiated with 3.5 MeV self-ions

Ion irradiation has been widely used to simulate radiation damage induced by neutrons. However, there are a number of features of ion-induced damage that differ from neutron-induced damage, and these differences require investigation before behavior arising from neutron bombardment can be confidently predicted from ion data. In this study 3.5 MeV self-ion irradiation of pure iron was used to study the influence on void swelling of the depth-dependent defect imbalance between vacancies and interstitials that arises from various surface effects, forward scattering of displaced atoms, and especially the injected interstitial effect. The depth dependence of void swelling was observed not to follow the behavior anticipated from the depth dependence of the damage rate. Void nucleation and growth develop first in the lower-dose, near-surface region, and then, during continued irradiation, move to progressively deeper and higher-damage depths. This indicates a strong initial suppression of void nucleation in the peak damage region that continued irradiation eventually overcomes. This phenomenon is shown by the Boltzmann transport equation method to be due to depth-dependent defect imbalances created under ion irradiation. These findings thus demonstrate that void swelling does not depend solely on the local dose level and that this sensitivity of swelling to depth must be considered in extracting and interpreting ion-induced swelling data.

36 MATERIALS SCIENCE↗

The Role of Co-injected Helium on Swelling and Cavity Evolution at High Damage Levels in Ferritic-Martensitic Steels

The influence of helium co-injection at rates from 0 to 4 appm He/dpa on swelling in ferritic-martensitic alloys T91 and HT9 was explored. Irradiations with 5.0 MeV Fe++ ions and degraded He++ ions were performed at 445°C up to damage levels of 150 dpa and helium co-injection rates of 0, 0.02, 0.2 and 4 appm He/dpa in T91, and at 460°C to a damage level of 188 dpa and helium co-injection rates of 0, 0.06 and 4 appm He/dpa in HT9. Helium was observed to enhance cavity nucleation at low damage levels, resulting in the maximum swelling at the highest helium co-injection rate. As the damage level was increased, the helium content at which swelling was maximized shifted to lower helium concentrations, ultimately resulting in the highest swelling occurring with zero helium by 150 dpa. Finally, this behavior was due to the helium-stabilized bubble microstructure that increased the cavity sink strength and reduced both cavity growth rate and swelling relative to the helium-free condition.

36 MATERIALS SCIENCE↗

Comparison of void swelling of ferritic-martensitic and ferritic HT9 alloys after high-dose self-ion irradiation

In this work, ferritic-martensitic (F/M) HT9 along with fully ferritic HT9 specimens were irradiated using self-ions to 600 peak displacement-per-atom (dpa) at 450 °C. To investigate and minimize the carbon contamination effect on void swelling, two identical F/M HT9 specimens were prepared: one without a coating and the other one with a tungsten and silver coating on the surface prior to irradiation. The specimen without a coating showed carbide formation in the matrix, resulting from carbon contamination during irradiation, with no voids observed. The coated sample did not form matrix carbides, and voids were observed within the irradiated region. The same coating was applied to the ferritic HT9, and void swelling results of both the F/M HT9 and the ferritic HT9 alloys were compared after irradiation. The F/M HT9 exhibited a maximum of 2.6% swelling, while the ferritic HT9 showed a maximum of 0.8% swelling at a 400–500 nm depth, equivalent to 334 local dpa. The results were correlated with the instability of carbides in the ferritic HT9 under irradiation. Carbides in the F/M HT9 and the ferritic HT9 are both M23C6, but the matrix carbides in the ferritic HT9 were less stable under the irradiation, compared to the ones on the grain boundaries in the F/M HT9. The study shows the impact of chemistry on the void swelling which overpowers the microstructural factors such as grain size and phase.

36 MATERIALS SCIENCE↗

BISON-FIPD integration enhanced low-burnup SFR metallic fuel swelling model evaluation framework

Experiments indicated that metallic fuel in sodium-cooled fast reactors (SFRs) rapidly swells radially and axially at low burnup. Despite that, prior studies have been focused on describing high burnup axial fuel elongation. With recent conventional and non-conventional metallic fuel concepts being considered for license applications, understanding multidimensional fuel swelling at a wide range of burnup levels is important to fuel analysis and qualification activities. Here, we report the development and demonstration efforts of a low-burnup SFR metallic fuel swelling model evaluation framework using the BISON advanced fuel performance code. The framework leverages the Integral Fast Reactor (IFR) program X423 experiment data through the ongoing integration project to enable standardized and automated use of legacy metallic fuel irradiation data maintained in the SFR fuel irradiation and physics database (FIPD) for BISON metallic fuel model verification and validation. In conclusion, the performance of the framework was demonstrated using the two representative metallic fuel swelling model sets implemented in BISON, with a series of insights about future advanced swelling model development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Swelling characteristics of DNA polymerization gels

The development of biomolecular stimuli-responsive hydrogels is important for biomimetic structures, soft robots, tissue engineering, and drug delivery. DNA polymerization gels are a new class of soft materials composed of polymer gel backbones with DNA duplex crosslinks that can be swollen by sequential strand displacement using hairpin-shaped DNA strands. The extensive swelling can be tuned using physical parameters such as salt concentration and biomolecule design. Previously, DNA polymerization gels have been used to create shape-changing gel automata with a large design space and high programmability. Here we systematically investigate how the swelling response of DNA polymerization gels can be tuned by adjusting the design and concentration of DNA crosslinks in the hydrogels or DNA hairpin triggers, and the ionic strength of the solution in which swelling takes place. Finally, we also explore the effect hydrogel size and shape have on the swelling response. Tuning these variables can alter the swelling rate and extent across a broad range and provide a quantitative connection between biochemical reactions and macroscopic material behaviour.

59 BASIC BIOLOGICAL SCIENCES↗

Controlling swelling in mixed transport polymers through alkyl side-chain physical cross-linking

Semiconducting conjugated polymers bearing glycol side chains can simultaneously transport both electronic and ionic charges with high charge mobilities, making them ideal electrode materials for a range of bioelectronic devices. However, heavily glycolated conjugated polymer films have been observed to swell irreversibly when subjected to an electrochemical bias in an aqueous electrolyte. The excessive swelling can lead to the degradation of their microstructure, and subsequently reduced device performance. An effective strategy to control polymer film swelling is to copolymerize glycolated repeat units with a fraction of monomers bearing alkyl side chains, although the microscopic mechanism that constrains swelling is unknown. Here we investigate, experimentally and computationally, a series of archetypal mixed transporting copolymers with varying ratios of glycolated and alkylated repeat units. Experimentally we observe that exchanging 10% of the glycol side chains for alkyl leads to significantly reduced film swelling and an increase in electrochemical stability. Through molecular dynamics simulation of the amorphous phase of the materials, we observe the formation of polymer networks mediated by alkyl side-chain interactions. When in the presence of water, the network becomes increasingly connected, counteracting the volumetric expansion of the polymer film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Super-swelling behavior of stacked lipid bilayer systems

Bilayer systems comprising lipid mixtures are the most well-studied model of biological membranes. While the plasma membrane of the cell is a single bilayer, many intra- and extra-cellular biomembranes comprise stacks of bilayers. Most bilayer stacks in nature are periodic, maintaining a precise water layer separation between bilayers. That equilibrium water separation is governed by multiple inter-bilayer forces and is highly responsive. Biomembranes re-configure inter-bilayer spacing in response to temperature, composition, or mass transport cues. In synthetic bilayer systems for applications in cosmetics or topical treatments, control of the hydration level is a critical design handle. Herein we investigate a binary lipid system that leverages key inter-bilayer forces leading to unprecedented levels of aqueous swelling while maintaining a coherent multilamellar form. We found that combining cationic lipids with bicontinuous cubic phase-forming lipids (lipids with positive Gaussian modulus), results in the stabilization of multilamellar phases against repulsive steric forces that typically lead to bilayer delamination at high degrees of swelling. Using ultra-small-angle X-ray scattering alongside confocal laser scanning microscopy, we characterized various super-swelled states of 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP) and glycerol monooleate (GMO) lipids, as well as other analogous systems, at varied concentration and molar ratios. Through these experiments we established swelling profiles of various binary lipid systems that were near-linear with decreasing lipid volume fraction, showing maximum swelling with periodicity well above 200 nanometers.

42 ENGINEERING↗

Solubility and volume swell of fuel system elastomers with ketone blends of E10 gasoline and blendstock for oxygenate blending (BOB)

The compatibility of key infrastructure elastomers with five ketone molecules was assessed via solubility studies and volume swell measurements. The elastomer materials included two fluorocarbons, six acrylonitrile butadiene rubbers (NBRs), and one each of fluorosilicone, neoprene, polyurethane, styrene butadiene rubber (SBR), and silicone. The ketone molecules included acetone, 2-butanone, 2-pentanone, 2-nonanone, and cyclopentanone. The ketones were added to gasoline containing 10% ethanol (E10) and a blendstock for oxygenate blending (BOB) in levels ranging from 0% to 30% by volume. The elastomers were exposed for 4 weeks in each test fluid. The solubility was modeled using Hansen solubility parameters and the volume change was determined for each material and test fuel. In general, the volume swell increased with ketone content and corresponded well to the predicted solubilities. In most cases, the highest level of swelling occurred with added cyclopentanone and acetone, while 2-nonanone produced the lowest levels of volume expansion. The chain length of the straight ketones was found to affect the volume swell behavior as volume expansion decreased with increasing chain length. This behavior is attributed to the reduction in polarity and hydrogen bonding with chain length. Neoprene, SBR, and silicone exhibited poor compatibility with the ketone molecules at all blend levels. Fluorocarbon and fluorosilicone also showed poor compatibility but may be suitable for use as static seals in very low blend levels with 2-nonanone. The results were more mixed for polyurethane and the NBRs. In general, better compatibility (low volume swell) was observed for mixtures containing BOB than for E10. This is due to the lower polarity and hydrogen bonding of the BOB.

10 SYNTHETIC FUELS↗

Elastomer Swell Behavior in 1-Propanol, Diisobutylene, Cyclopentanone, and a Furan Mixture Blended in E10 and a Blendstock for Oxygenate Blending (BOB)

The compatibility of four potential bio-derived blendstock molecules with infrastructure elastomers was determined by measuring the volume change following exposure. The blendstock molecules included 1-propanol, diisobutylene, cyclopentanone, and a furan mixture. The elastomers included two fluorocarbons, six nitrile rubbers (NBRs), and one each of fluorosilicone, neoprene, polyurethane, and silicone. The elastomers were exposed to the fuel molecules as blends ranging from 0 to 30 vol.% in both a blendstock for oxygenate blending (BOB) formulation and an E10 fuel. Silicone exhibited excessive swelling in each test fuel, while the other elastomers showed good compatibility (low swell) with diisobutylene, 1-propanol, and the furan mixture when BOB was used as the base fuel. The E10 base fuel produced high (>30%) swell in neoprene, polyurethane, and some nitrile rubbers. In most cases diisobutylene produced the least amount of volume expansion. In contrast, the addition of cyclopentanone produced unacceptably high swelling in each elastomer and is not considered suitable for use with these fuels. Analysis of the results showed that the swelling behavior is predominantly due to the polarity of the elastomer and test fuels.

03 NATURAL GAS↗

A Study of the Swelling and Bursting of the High Pressure Coupling (HPC) of a Two-Stage Light Gas Gun

A consistent picture of the swelling and bursting of the high pressure couplings (HPC) of two NASA Ames two-stage light gas guns is developed. The following information is used to construct the model. 1. Experimental measurements of the swelling and bursting of the HPCs of two two-stage light gas guns. 2. Stress-strain calculations of the swelling and bursting of thick walled steel tubes. 3. Experimental measurements swelling and bursting of thick walled steel tubes. 4. CFD calculations of the maximum pressures in the HPC of a two-stage light gas gun using the code LGGUN 5. Correlation of maximum HPC pressures and piston energies It is suggested that the techniques described herein could be used to assess the likelihood of swelling and bursting of the HPCs of various different two stage light gas guns.

David W Bogdanoff↗

A Study of the Swelling and Bursting of the High Pressure Coupling (HPC) of a Two-Stage Light Gas Gun

A consistent picture of the swelling and bursting of the high pressure couplings (HPC) of two NASA Ames two-stage light gas guns is developed. The following information is used to construct the model. 1. Experimental measurements of the swelling and bursting of the HPCs of two two-stage light gas guns. 2. Stress-strain calculations of the swelling and bursting of thick walled steel tubes. 3. Experimental measurements swelling and bursting of thick walled steel tubes. 4. CFD calculations of the maximum pressures in the HPC of a two-stage light gas gun using the code LGGUN It is suggested that the techniques described herein could be used to assess the likelihood of swelling and bursting of the HPCs of various different two stage light gas guns.

David W Bogdanoff↗

Modeling swelling behavior of hydrogels in aqueous organic solvents

Hydrogel, a three-dimensional elastic structure of cross-linked polymer chains, swells or deswells when immersed in aqueous organic solutions. The swelling of hydrogels depends on temperature, solvent composition, and hydrogel structure as the thermodynamic driving forces for hydrogel swelling are due to solvent – hydrogel interactions and expansion of elastic network. Here in this work, polymer Nonrandom Two-Liquid activity coefficient model is used to account for the solvent – hydrogel interactions and a semi-empirical expression for rubber elasticity is used to describe the expansion of elastic network. The model successfully correlates data for both swelling and equilibrium phase compositions for n-isopropyl acrylamide hydrogels in water – ethanol, water – acetone, water – n-butanol, and water – methyl isobutyl ketone mixed solvents.

42 ENGINEERING↗

Quantification of Swelling in Hematite Pellets Reduced Using Hydrogen–Nitrogen Gas Mixture

Iron ore pellets are reduced in a 50%H 2 –50%N 2 1 atm gas mixture at 750, 800, 850, 900, and 950 °C while simultaneously documenting swelling (change in pellet radius) and weight change. Swelling increases with increasing temperature, with catastrophic swelling (>20% of reduction swelling index) observed at 850, 900, and 950 °C. As the pellet is reduced, the pellet radius increases until 40–50% reduction is achieved, followed by a decrease in diameter beyond 40–50% reduction at 750 and 850 °C. At 950 °C, the pellet radius continues to increase with additional pellet reduction without any subsequent decrease in diameter. Scanning electron microscopy (SEM) analysis shows that the neighboring grains inside the pellet sinter together at 750 and 850 °C, whereas the individual grains sinter internally at 950 °C. SEM analysis and observations suggest that the reduction process at 750 and 850 °C can be approximated as a topochemical reaction process, while the reduction process at 950 °C can no longer be approximated as a topochemical reaction process. In conclusion, an empirical equation for the radius of the pellet is derived with fitting parameters dependent on temperature and the degree of reduction of the pellet undergoing reduction based on the experimental data.

08 HYDROGEN↗

Chloride channels activated by swell can regulate the NADPH oxidase generated membrane depolarisation in activated human neutrophils

Chloride channels activated by swell have important functions in many physiological processes. The phagocyte NADPH oxidase is essential for host defence and it generates superoxide by transferring electrons from the donor NADPH to the acceptor O{sub 2}. This electron current, induces a depolarisation of the plasma membrane. In this study, I report that chloride channels activated by swell can counteract the depolarisation induced by the NADPH oxidase. When a chloride conductance was activated by swelling, its inhibition by either 50 {mu}M NPPB or removing external chloride, depolarised the plasma membrane potential to +26 mV {+-} 3.1 (n = 4) and +40 {+-} 1 mV (n = 4), respectively. These channels were partially inhibited by the NADPH oxidase inhibitor AEBSF (1 mM) and potently inhibited by ZnCl{sub 2} (3 mM). These currents were not activated by a phosphorylation step and elevations in intracellular calcium did not appear to activate chloride currents similar to those activated by swell.

60 APPLIED LIFE SCIENCES↗

An in-situ view cell system for investigating swelling behavior of elastomers upon high-pressure hydrogen exposure

The transition to hydrogen as a clean and efficient energy carrier is impeded by challenges in the compatibility of hydrogen with materials used within hydrogen infrastructure. Elastomers, crucial in sealing components, often exhibit premature failures in high-pressure hydrogen environments due to excessive swelling. This study employs an innovative in-situ view cell system to assess the swelling behavior of hydrogenated nitrile butadiene rubber (HNBR) under various hydrogen conditions. The system, designed to withstand pressures up to 96.5 MPa, incorporates Digital Image Correlation (DIC) for strain measurements and volume estimation. Results reveal non-linear volume increases during depressurization, challenging conventional assumptions. Furthermore, investigations into peak hydrogen pressures and pressure-holding scenarios during decompression highlight complex swelling trends. The introduction of a novel computer vision (CV) method enhances precision in volume estimation, overcoming DIC limitations. The study provides insights into mitigating elastomer swelling, crucial for developing robust materials to support future hydrogen-driven energy systems.

Elastomer↗

In situ investigation of high-pressure hydrogen-induced swelling in elastomers and its correlation with material properties

The resistance of elastomeric materials to high-pressure hydrogen-induced damage is essential for ensuring the reliability of hydrogen infrastructure. Here, in this study, we systematically investigated the swelling behavior and hydrogen transport properties of four elastomer types – EPDM, NBR, FKM, and HNBR – using a custom in-situ view cell system capable of real-time monitoring during decompression from pressures up to 96.5 MPa. Each elastomer was formulated with and without fillers and plasticizers to assess the effects of formulation on swelling response. Thermal desorption analysis (TDA) was employed to determine equilibrium hydrogen content and diffusion coefficients, providing insight into gas uptake and mobility within each material. Correlation analyses using Pearson and Spearman coefficients revealed that the diffusion coefficient showed a stronger relationship with swelling behavior than hydrogen content, highlighting the dominant role of hydrogen mobility. Filled elastomers, particularly those with carbon black, consistently showed reduced swelling due to enhanced stiffness and reduced diffusivity. These results deepen our understanding of diffuso-mechanical interactions in elastomers and support the rational design of sealing materials for high-pressure hydrogen systems.

EPDM↗

Neutron-Induced Swelling and Embrittlement of Pure Iron and Pure Nickel Irradiated in the BN-350 and BOR-60 Fast Reactors

Pure iron and nickel were irradiated in the range of 2 to 15 x 10-7 dpa/sec at 345-650 degrees C to very high neutron exposures in two fast reactors, BOR-60 and BN-350, to study void swelling and changes in mechanical properties of these two metals. Both nickel and iron swell in this temperature range with the maximum swelling rate at ~500 degrees C in nickel but possibly at <350 degrees C for iron. It also appears that the swelling rate in nickel may be dependent on the dpa rate, increasing with decreasing dpa rate.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Cavity evolution and void swelling in dual ion irradiated tempered martensitic steels

Microstructural evolutions in two variants of the F82H 8 wt%Cr tempered martensitic steel under dual (He + plus Fe 3+ ) ion irradiations at 500 °C have been characterized by transmission electron microscopy. Emphasis is on understanding the combined effects of displacements per atom (dpa) and the helium/dpa ratio (He/dpa) on cavity evolution and void swelling (f v ). The dual ion database includes 231 alloy-dpa-He/dpa conditions for irradiations up to ~ 82 dpa and 3700 appm helium. Here, we hypothesize that the large “scatter” observed in the f v data is primarily due to local microstructural variations, especially those that shield regions at shallower depths from the effects of injected interstitial atoms, which would otherwise reduce f v . More generally, our hypothesis is that the highest f v data, at a specified dpa and He/dpa, provides the most appropriate estimate of swelling for fusion neutron irradiation conditions. The dose dependence of f v can be described by an incubation dpa i , marking the onset of significant void growth, and a post-incubation swelling rate, f v ’ = Δf v /Δdpa. Both dpa i and f v ’ decrease with increasing He/dpa. The f v ’ data are quantitatively consistent with a simple model for defect partitioning between evolving bubble, void, and dislocation sinks strengths and biases. Most notably, the model correctly predicts both the incubation dpa i , and the subsequent f v ’, in spite of the fact that they reflect somewhat different physics. Our analysis also suggests that defect recombination is modest at 500 °C. Along with other considerations, this supports the hypothesis that, even at high dpa rates, dual ion irradiations can be used to reasonably emulate void nucleation and growth for a range of fusion-relevant neutron irradiation service conditions. A companion paper incorporates the results of this study in a reduced-order, data-driven void swelling model.

36 MATERIALS SCIENCE↗