Search NASA⌕ Search

SEARCH · Search NASA

Results for “Silicon Carbide Composite Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Characterization of LWRS Hybrid SiC-CMC-Zircaloy-4 Fuel Cladding after Gamma Irradiation

The purpose of the gamma irradiation tests conducted at the Idaho National Laboratory (INL) was to obtain a better understanding of chemical interactions and potential changes in microstructural properties of a mock-up hybrid nuclear fuel cladding rodlet design (unfueled) in a simulated PWR water environment under irradiation conditions. The hybrid fuel rodlet design is being investigated under the Light Water Reactor Sustainability (LWRS) program for further development and testing of one of the possible advanced LWR nuclear fuel cladding designs. The gamma irradiation tests were performed in preparation for neutron irradiation tests planned for a silicon carbide (SiC) ceramic matrix composite (CMC) zircaloy-4 (Zr-4) hybrid fuel rodlet that may be tested in the INL Advanced Test Reactor (ATR) if the design is selected for further development and testing

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Completion of the Irradiation of Silicon Carbide Cladding Tube Specimens in the High Flux Isotope Reactor

This document outlines the irradiation of silicon carbide cladding tube specimens in the High Flux Isotope Reactor at Oak Ridge National Laboratory. The cladding tube specimens consisted of monolithic, composite, and coated SiC specimens in order to test the effect of these various materials on the overall cladding performance during irradiation. A total of 18 specimens were irradiated for one cycle, with 9 specimens irradiated at low heat flux conditions and 9 specimens at high heat flux conditions. The specimens were inserted in cycle 475 in September 2017 and reached an average irradiation dose of approximately 2.6 dpa.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

X-ray characterization of atomistic defects causing irradiation creep of SIC

Silicon carbide (SiC) fiber–reinforced SiC matrix composites have been widely studied for use in developing an accident-tolerant fuel (ATF) cladding for light water reactors (LWRs) in recent years because of their superior oxidation and irradiation resistance and low neutron absorption cross section. An important task is the establishment of the thermo-mechanical analysis capability to predict the in-pile performance and failure probability of the cladding. Irradiation creep is known to be a key property in modeling the stress state under irradiation. To better understand the radiation creep mechanism from an atomic point of view, this study conducted synchrotron-based X-ray diffraction (XRD) experiments on SiC neutron-irradiated with and without applied stress at the National Synchrotron Light Source-II (NSLS-II). This report presents progress of the XRD study and future plans. The important finding obtained was that the macroscopic creep strain and strain due to the lattice expansion were similar in case of neutron irradiation at 300°C to 0.1 displacement per atom (dpa), which indicates that the lattice strain is a major source of the transient creep strain.

36 MATERIALS SCIENCE↗

Development of SiC-based Cladding for Accident Tolerant Fuels

Fuels and core structures in current light water reactors (LWR's) are vulnerable to catastrophic failure in severe accidents. This vulnerability is attributed primarily to the rapid oxidation kinetics of zirconium alloys in a water vapor environment at very high temperatures. Alternative materials to zirconium alloys with reduced oxidation kinetics are sought to enable enhanced accident-tolerant fuels and cores. Among the candidate alternatives, silicon carbide (SiC) - based materials, in particular continuous SiC fiber-reinforced SiC matrix ceramic composites (SiC/SiC composites), are considered to offer outstanding safety benefits. The primary objective of this work is to provide with updated overviews of the concepts, development status, and future prospect for the SiC-based accident-tolerant fuel (ATF) claddings. A systematic technology evaluation program plan was developed and updated to review the technologies needed, to identify and analyze critical gaps, and to lay out a road-map toward establishing key technologies. The technology review and the gap analysis in this exercise were based on an early study and community workshops. Many of the technical gaps identified are related with the three key feasibility issues: hydrothermal corrosion, mechanical failure, and fuel compatibility. Additional performance issues including accident-tolerance features and fission product retention during the normal operation have also been identified. The program plan was designed to systematically address the key gap issues and is formulated in a work breakdown structure. Simultaneously, the plan is being established to set a technical program for advancing the technological readiness levels of concept non-specific essential technologies in three top-level categories of Design and Failure, Environmental Effects, and Off-normal Behavior. The execution of the program plan is in progress across the U.S. Department of Energy laboratories, industries, universities, and international collaborators. The critical issues for SiC composite-based fuel cladding concepts were found to be related to the performance in the normal operation. In particular, radiation-assisted hydrothermal corrosion and the gaseous fission product (FP) retention are identified to be the most critical issues. The primary ORNL concept pursues the use of dual-purpose coating on the SiC composite cladding wall to mitigate the corrosion and the gas permeation issues at the same time, whereas the alternative approaches such as the dense monolithic SiC protective layer combined with the water chemistry control may be feasible. Surface metallization through variations of physical vapor deposition and electroplating are being demonstrated. The FP gas retention is an issue associated with the cracking for the ceramic matrix composite cladding. To establish the probabilistic failure behavior, the relevant test methods were developed in ASTM Committee C28 on Advanced Ceramics. Toward the end-plugging technology development, various methods for joining SiC to SiC had been developed and tested for mechanical properties, irradiation effects, and environmental effects. Multiple methods including the pressureless transient eutectic SiC joining and CVD-based SiC joining were identified particularly promising. In addition, a multi-physics, three-dimensional finite element-based modeling is in progress toward an integrated simulation of the SiC composite-cladded fuel evolutions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Deformation analysis of SiC-SiC channel box for BWR applications

Silicon carbide fiber-reinforced silicon carbide matrix (SiC-SiC) composites are being considered as components in light water reactor cores to improve accident tolerance, including channel boxes and fuel cladding. In the nuclear reactor environment, core components like a channel box will be exposed to neutron and other radiation damage and temperature gradients. To ensure reliable and safe operation of a SiC-SiC channel box, it is important to assess its deformation behavior under in-reactor conditions including the expected neutron flux and temperature distributions. In particular, this work has evaluated the effect of non-uniform dimensional changes caused by spatially varying neutron flux and temperatures on the deformation behavior of the channel box over the course of one year. These analyses have been performed using the fuel performance modeling code BISON and the commercial finite element analysis code Abaqus, based on fast flux and temperature boundary conditions that have been calculated using the neutronics and thermal-hydraulics codes Serpent and CTF, respectively. The dependence of dimensions and thermophysical properties on fast flux and temperature has been incorporated into the material models. These initial results indicate significant bowing of the channel box with a lateral displacement greater than 6.5 mm. The channel box bowing behavior is time dependent and driven by the temperature dependence of the SiC irradiation-induced swelling and the neutron flux/fluence gradients. The bowing behavior gradually recovers during the course of the operating cycle as the swelling of the SiC-SiC material saturates. Furthermore, the bending relaxation due to temperature gradients does not fully recover and residual bending remains after the swelling saturates in the entire channel box.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fabrication of New NFA-SiC Composites for Nuclear Applications

Cladding materials play the critical and fundamental function of fuel confinement during the safe operation of a nuclear power system. With the development of a new generation of nuclear reactors, investigation of the corresponding advanced cladding materials is attracting intensive scrutiny. Nanostructured ferritic alloy (NFA), which has excellent irradiation resistance and mechanical performance, is one primary candidate for future fission and fusion reactors. The NFA alloys are composed of nano-grained Fe-Cr alloy domains and Y-Ti-O-Cr-Fe enriched nano-clusters. The nano-clusters can not only prevent dislocation glide, grain growth, and grain boundary slip, but also act as sinks to trap helium atoms and radiation-generated point defects. In addition, NFAs can provide high temperature strength and prominent thermal stability, which are beneficial to nuclear cladding applications. Silicon carbide (SiC) is another nuclear cladding candidate. Due to its physical and chemical stability, it shows very good refractory properties at high temperatures up to 2000 deg. C, which has enabled its wide applications in combustion chamber and aerospace engines. In addition, SiC has the remarkable characteristic of radiation stability. SiCf/SiC composite has been developed as an alternative cladding material to metallic alloys. Theoretical simulation is also being developed to understand irradiation induced defects in SiC. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel performance of chromium-coated zirconium alloy and silicon carbide accident tolerant fuel claddings

The U.S. Department of Energy’s Accident Tolerant Fuel program is focused on extending the time for fuel failure during postulated severe accidents compared to the standard UO2-Zr alloy fuel system. This research investigates the feasibility of two different chromium-coated cladding concepts, one of which is zirconium-alloy based and the other is composite-SiC based. Both claddings had 50µm coatings, deducted from the base layer thicknesses. The claddings were reported on, using the multi- physics fuel performance tool BISON, under steady-state PWR operating conditions as well as two transients: power ramp and a loss-of-coolant accident (LOCA). The chromium-coated claddings showed comparable thermo-mechanical performance to the reference Zircaloy-4 cladding. As chromium is reported to provide an order of magnitude improvement in oxidation resistance, it is expected to be a better alternative in accident scenarios. Simulation results for both concepts call for further experimental investigation as well as modeling of beyond design-basis accidents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Westinghouse Accident Tolerant Fuel Phase 2B with Higher Enriched and Higher Burnup Add-On Project Final Technical Report Deliverable Volume 1

The Westinghouse Electric Company LLC (Westinghouse) accident tolerant fuel (ATF) program funded by Westinghouse and the US Department of Energy (DOE) utilized chromium (Cr) coated zirconium alloy cladding with doped UO 2 (ADOPT(TM)) and uranium silicide (U 3 Si 2 ) high density/high thermal conductivity fuel for its lead test rod (LTR) program with irradiation beginning in 2019. ADOPT is a Cr 2 O 3 +Al 2 O 3 doped UO 2 pellet with increased oxidation resistance and density, and increased resistance to fission gas release. Due to the issues with U 3 Si 2 fuel reaction in pressurized water reactor (PWR) environments, uranium nitride (U 15 N) has been substituted for U 3 Si 2 as a long-term fuel option. Cr coated cladding with ADOPT fuel is the near-term Westinghouse EnCore fuel product. The long-term EnCore ® fuel product is SiGA ® SiC/SiC composite cladding with high density/high thermal conductivity UN fuel. In 2020, the higher burnup and higher enriched and (HBHE) program was integrated into the ATF program. The objective of this expanded program is to extend ATF burnups to at least 75 MWd/kgU to economically facilitate 24-month cycles in PWRs. The ATF program now includes ADOPT fuel with enrichments >5% 235 U. Over the past several years, Westinghouse has tested the Cr coated zirconium (Zr) and silicon carbide (SiC) claddings in Westinghouse Churchill autoclaves and the Massachusetts Institute of Technology (MIT) reactor. Additionally, the Cr coated cladding has been tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and in LTR programs at the Doel 4 and Bryon 2 commercial reactors. High temperature tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried out to determine the time and temperature limits for the Cr coated zirconium claddings. These tests indicate that Cr coated Zr cladding can take temperatures up to about 1500°C for short periods of time without becoming totally oxidized. The main issue is the formation of the Cr-Zr eutectic at 1333°C resulting in the migration of this eutectic inward with the formation of ZrCr 2 which rapidly oxidizes to ZrO 2 on the outside of the tube. The Cr coated Zr cladding also delays the bursting of the tube, reduces the burst area, and reduces hydriding and embrittlement of the Zr which is a major benefit for reducing fuel fragmentation, redistribution, and dispersal (FFRD), the major licensing issue faced by HBHE. The manufacturing parameters for the SiC have been found to have a significant effect on the corrosion rate of the SiC in light water reactor (LWR) conditions and significant improvements have been made in the yield, quality, and oxidation resistance of the SiC cladding by identifying and tightening manufacturing process parameters. Current autoclave results for SiC composite claddings indicate that a corrosion rate of fewer than 2 micrometers per year can be achieved which meets corrosion requirements under normal operating conditions. High temperature steam oxidation tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried and determined that SiC cladding can withstand temperatures up to about 1800°C to 1900°C before excessive corrosion reactions begin, and that the SiC will not balloon and burst. ADOPT fuel pellets were incorporated into the Westinghouse ATF program because of their increased density and oxidation resistance. A topical report supporting the use of ADOPT pellets has been submitted to the NRC and will be approved shortly. ADOPT pellets have been a product in Europe for over 15 years. The additives work to make larger grain sizes which appear to reduce fission gas release during transients as well as increase the density of the pellet. Fuel rod and assembly design in preparation for the lead test rod (LTR) and lead test assembly (LTA) programs is underway as well as licensing efforts with the Nuclear Regulatory Commission (NRC). Finally, accident analyses coupled with economic evaluations for both operating savings as well as fuel savings have been initiated. Modular Accident Analysis Program 5 (MAAP5) calculations indicate that both Cr coated cladding and SiC composite cladding can increase the time to fuel rod loss of geometry for up to two hours longer than current Zr based cladding in a station blackout scenario. This additional time is due to the much higher oxidation resistance of the SiC and Cr coated cladding. These two hours can be used to implement additional response options instituted through the Diverse and Flexible Mitigation Capability (FLEX) program by reactor operators. Both ATF cladding options also reduce hydrogen production which dramatically reduces primary system and containment pressure and the risk of fission product release beyond containment in the unlikely event of an accident. The lower pressure in the system allows more time to feed cooling water to the core, resulting in the avoidance of fuel melting. The coping time is extended indefinitely if the modest water flow provided by FLEX continues. Experimental work on methods to rapidly fabricate SiC composite structures with high density and reduce the fabrication price of SiC fibers while maintaining a high level of performance is needed. Methods for mitigating or stopping the Cr-Zr eutectic are also needed to further improve the oxidation resistance of Cr coated Zr. Minimal (<1%) swelling of U 3 Si 2 and subsequent fission gas release has been demonstrated up to 20 MWd/kgU. Irradiation experiments with U 3 Si 2 fuel in ATR to determine these properties at 40 MWd/kgU were completed but post irradiation examinations were not done since U 3 Si 2 has been replaced by UN. UN has three issues that are being addressed. The first is increasing the oxidation resistance so that there is not excessive reaction up to ~1500°C. While UN increases the pellet density and additives to the UN postponed the temperature at which rapid oxidation occurred by ~100°C to 200°C, this is not enough, and pellet coating options are now being pursued. The second is developing a method to manufacture that does not require the multi-step process of UF 6 to UO 2 to UC to UN. Efforts are underway looking at UF 6 to UN 2 to UN and UF 6 to UF 4 to UN 2 to UN reactions. Finally, an economically acceptable process for potentially enriching the 15 N content of the nitrogen used to make UN to >95% 15N was identified though not experimentally validated. In addition to the work supported by the DOE, research and testing activities are being carried on in a world-wide effort funded by many countries such as Sweden, United Kingdom, Belgium, Netherlands, Spain, Germany, Japan, and France. This work is being facilitated through the Westinghouse led Collaboration for Advanced Research on Accident Tolerant Fuel (CARAT) program. Annual meetings were organized in 2018 and 2019 by Westinghouse as a venue for presentation of this work and to provide for the cross-fertilization of ideas among the many outstanding researchers in the ATF area. No meetings were held in 2020 and 2021 due to the COVID-19 related restrictions on traveling and gatherings. Since SiC, coated cladding, and high-density fuel options are not currently used in the nuclear industry; support from the government and industry members is needed to further the significant effort of setting new standards. The same is true for the Nuclear Regulatory Commission (NRC) which must review and approve the commercial use of these new fuels since all current regulations are oriented toward Zr/UO 2 fuel. Several meetings have been held with the NRC to generate a fast-track approach to licensing ATF using a combination of atomic modeling, in-rod sensors, and in-reactor testing. This approach was memorialized in an “Accelerated Fuel Qualification White Paper” prepared by the Accelerated Fuel Qualification Working Group lead by General Atomics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Westinghouse Accident Tolerant Fuel Phase 2B with Higher Enriched and Higher Burnup Add-On Project Final Technical Report Deliverable Volume 2

The Westinghouse Electric Company LLC (Westinghouse) accident tolerant fuel (ATF) program funded by Westinghouse and the US Department of Energy (DOE) utilized chromium (Cr) coated zirconium alloy cladding with doped UO 2 (ADOPT(TM)) and uranium silicide (U 3 Si 2 ) high density/high thermal conductivity fuel for its lead test rod (LTR) program with irradiation beginning in 2019. ADOPT is a Cr 2 O 3 +Al 2 O 3 doped UO 2 pellet with increased oxidation resistance and density, and increased resistance to fission gas release. Due to the issues with U 3 Si 2 fuel reaction in pressurized water reactor (PWR) environments, uranium nitride (U 15 N) has been substituted for U 3 Si 2 as a long-term fuel option. Cr coated cladding with ADOPT fuel is the near-term Westinghouse EnCore ® fuel product. The long-term EnCore fuel product is SiGA ® SiC/SiC composite cladding with high density/high thermal conductivity UN fuel. In 2020, the higher burnup and higher enriched and (HBHE) program was integrated into the ATF program. The objective of this expanded program is to extend ATF burnups to at least 75 MWd/kgU to economically facilitate 24-month cycles in PWRs. The ATF program now includes ADOPT fuel with enrichments >5% 235 U. Over the past several years, Westinghouse has tested the Cr coated zirconium (Zr) and silicon carbide (SiC) claddings in Westinghouse Churchill autoclaves and the Massachusetts Institute of Technology (MIT) reactor. Additionally, the Cr coated cladding has been tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and in LTR programs at the Doel 4 and Bryon 2 commercial reactors. High temperature tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried out to determine the time and temperature limits for the Cr coated zirconium claddings. These tests indicate that Cr coated Zr cladding can take temperatures up to about 1500°C for short periods of time without becoming totally oxidized. The main issue is the formation of the Cr-Zr eutectic at 1333°C resulting in the migration of this eutectic inward with the formation of ZrCr 2 which rapidly oxidizes to ZrO 2 on the outside of the tube. The Cr coated Zr cladding also delays the bursting of the tube, reduces the burst area, and reduces hydriding and embrittlement of the Zr which is a major benefit for reducing fuel fragmentation, redistribution, and dispersal (FFRD), the major licensing issue faced by HBHE. The manufacturing parameters for the SiC have been found to have a significant effect on the corrosion rate of the SiC in light water reactor (LWR) conditions and significant improvements have been made in the yield, quality, and oxidation resistance of the SiC cladding by identifying and tightening manufacturing process parameters. Current autoclave results for SiC composite claddings indicate that a corrosion rate of fewer than 2 micrometers per year can be achieved which meets corrosion requirements under normal operating conditions. High temperature steam oxidation tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried and determined that SiC cladding can withstand temperatures up to about 1800°C to 1900°C before excessive corrosion reactions begin, and that the SiC will not balloon and burst. ADOPT fuel pellets were incorporated into the Westinghouse ATF program because of their increased density and oxidation resistance. A topical report supporting the use of ADOPT pellets has been submitted to the NRC and will be approved shortly. ADOPT pellets have been a product in Europe for over 15 years. The additives work to make larger grain sizes which appear to reduce fission gas release during transients as well as increase the density of the pellet. Fuel rod and assembly design in preparation for the lead test rod (LTR) and lead test assembly (LTA) programs is underway as well as licensing efforts with the Nuclear Regulatory Commission (NRC). Finally, accident analyses coupled with economic evaluations for both operating savings as well as fuel savings have been initiated. Modular Accident Analysis Program 5 (MAAP5) calculations indicate that both Cr coated cladding and SiC composite cladding can increase the time to fuel rod loss of geometry for up to two hours longer than current Zr based cladding in a station blackout scenario. This additional time is due to the much higher oxidation resistance of the SiC and Cr coated cladding. These two hours can be used to implement additional response options instituted through the Diverse and Flexible Mitigation Capability (FLEX) program by reactor operators. Both ATF cladding options also reduce hydrogen production which dramatically reduces primary system and containment pressure and the risk of fission product release beyond containment in the unlikely event of an accident. The lower pressure in the system allows more time to feed cooling water to the core, resulting in the avoidance of fuel melting. The coping time is extended indefinitely if the modest water flow provided by FLEX continues. Experimental work on methods to rapidly fabricate SiC composite structures with high density and reduce the fabrication price of SiC fibers while maintaining a high level of performance is needed. Methods for mitigating or stopping the Cr-Zr eutectic are also needed to further improve the oxidation resistance of Cr coated Zr. Minimal (<1%) swelling of U 3 Si 2 and subsequent fission gas release has been demonstrated up to 20 MWd/kgU. Irradiation experiments with U 3 Si 2 fuel in ATR to determine these properties at 40 MWd/kgU were completed but post irradiation examinations were not done since U 3 Si 2 has been replaced by UN. UN has three issues that are being addressed. The first is increasing the oxidation resistance so that there is not excessive reaction up to ~1500°C. While UN increases the pellet density and additives to the UN postponed the temperature at which rapid oxidation occurred by ~100°C to 200°C, this is not enough, and pellet coating options are now being pursued. The second is developing a method to manufacture that does not require the multi-step process of UF 6 to UO 2 to UC to UN. Efforts are underway looking at UF 6 to UN 2 to UN and UF 6 to UF 4 to UN 2 to UN reactions. Finally, an economically acceptable process for potentially enriching the 15 N content of the nitrogen used to make UN to >95% 15 N was identified though not experimentally validated. In addition to the work supported by the DOE, research and testing activities are being carried on in a world-wide effort funded by many countries such as Sweden, United Kingdom, Belgium, Netherlands, Spain, Germany, Japan, and France. This work is being facilitated through the Westinghouse led Collaboration for Advanced Research on Accident Tolerant Fuel (CARAT) program. Annual meetings were organized in 2018 and 2019 by Westinghouse as a venue for presentation of this work and to provide for the cross-fertilization of ideas among the many outstanding researchers in the ATF area. No meetings were held in 2020 and 2021 due to the COVID-19 related restrictions on traveling and gatherings. Since SiC, coated cladding, and high-density fuel options are not currently used in the nuclear industry; support from the government and industry members is needed to further the significant effort of setting new standards. The same is true for the Nuclear Regulatory Commission (NRC) which must review and approve the commercial use of these new fuels since all current regulations are oriented toward Zr/UO 2 fuel. Several meetings have been held with the NRC to generate a fast-track approach to licensing ATF using a combination of atomic modeling, in-rod sensors, and in-reactor testing. This approach was memorialized in an “Accelerated Fuel Qualification White Paper” prepared by the Accelerated Fuel Qualification Working Group lead by General Atomics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of LWR Fuels with Enhanced Accident Tolerance ATF Feasibility Analysis Report Deliverable for the Westinghouse Accident Tolerant Fuel Program

The Westinghouse Electric Company LLC (Westinghouse) accident tolerant fuel (ATF) program utilizes chromium (Cr) coated zirconium alloy cladding with uranium silicide (U 3 Si 2 ) high density/high thermal conductivity fuel for its lead test rod (LTR) program with irradiation beginning in 2019. The lead test assembly (LTA) program will use both SiC/SiC composites and Cr coated zirconium alloy claddings with the high density/high thermal conductivity U 3 Si 2 pellet which will begin in 2022. Over the past several years, Westinghouse has tested the Cr coated zirconium (Zr) and silicon carbide (SiC) claddings in autoclaves and in the Massachusetts Institute of Technology (MIT) reactor and the U 3 Si 2 pellets have been tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). High temperature tests at the state-of-the-art Westinghouse facilities in Churchill, PA have been carried out to determine the time and temperature limits for the SiC and Cr coated zirconium claddings. Fuel rod and assembly design in preparation for the LTR and LTA programs is underway as well as licensing efforts with the Nuclear Regulatory Commission (NRC). Finally, accident analyses coupled with economic evaluations for both operating savings as well as fuel savings have been initiated. Cr coated zirconium alloy claddings showed low corrosion rates in both autoclave and in-reactor tests and will be fabricated using commercial processes for the first LTRs for insertion in 2019. Current autoclave results for SiC composite claddings indicate that a corrosion rate of fewer than 2 micrometers per year which meets corrosion requirements may be achieved under normal operating conditions. Modular Accident Analysis Program 5 (MAAP5) calculations indicate that solid fission products can be contained within SiC cladding for up to two hours longer than current Zr based cladding in a station blackout scenario. This additional time is due to the much higher temperature capability of SiC (~2000°C). These two hours can be used to implement additional response options instituted through the FLEX program by reactor operators. While the Cr coated Zr alloy option offers more modest ATF gains (~200°C higher than bare Zr) in similar situations, the coatings do delay the runaway oxidation encountered by uncoated zirconium cladding. Both ATF cladding options also reduce hydrogen production which dramatically reduces primary system and containment pressure and the risk of fission product release beyond containment in the unlikely event of an accident. The lower pressure in the system allows more time to feed cooling water to the core, resulting in the avoidance of fuel melting. The coping time is extended indefinitely as long as the water flow continues. SiC exhibits the highest accident tolerance of any cladding and significant advances in understanding the design, manufacture and accident behavior of SiC cladding have been made. Department of Energy support is needed to continue the on-going experimental work addressing the interaction between U 3 Si 2 and SiC at temperatures >1200°C, the effect of SiC manufacturing methods and manufacturing variability on physical properties, and the ability to predict the mechanical properties of SiC composites based on the composite design. Additionally, experimental work on methods to rapidly fabricate SiC composite structures with high density and reduce the fabrication price of SiC fibers while maintaining a high level of performance is needed. Minimal (<1%) swelling of U 3 Si 2 and subsequent fission gas release has been demonstrated up to 20 MWd/kgU. Irradiation experiments with U 3 Si 2 fuel in ATR to determine these properties at 40 to 50 MWd/kgU are underway. These experiments will provide the data needed to license fuel rod design codes. Research is continuing on production methods for making U 3 Si 2 from UF 6 without going through the U metal step. Oxidation tests of fuel pellets and powder in steam and synthetic air indicate that U 3 Si 2 has a lower oxidation reaction initiation temperature than UO 2 . Options to reduce the U 3 Si 2 oxidation rate are being explored. A hybrid fuel design using pellets with the weight ratio of 30%/70% U 3 Si 2 /UN is currently undergoing testing in the ATR. This approach is being explored to further increase the positive economics of the U 3 Si 2 fuel. In addition to the work supported by the USDOE, research and testing activities are being carried on in a world-wide effort funded by many countries such as Sweden, United Kingdom, Belgium, Netherlands, Spain, Germany, Japan and France. This work is being facilitated through the Westinghouse led Collaboration for Advanced Research on Accident Tolerant Fuel (CARAT) program. Annual meetings are organized by Westinghouse as a venue for presentation of this work and to provide for the cross-fertilization of ideas among the many outstanding researchers in the ATF area. Since SiC, coated cladding and high density fuel options are not currently used in the nuclear industry, support from the government and industry members is needed to further the significant effort of setting new standards. The same is true for the Nuclear Regulatory Commission (NRC) which must review and approve the commercial use of these new fuels since all current regulations are oriented toward Zr/ UO 2 fuel. There are no showstoppers for accident tolerant fuel technologies when considering supply chain, fabrication, enrichment suppliers, production, and licensing. Due to the cost savings from higher density fuel and the accident tolerance of coated claddings, Exelon has identified potential commercial plants to host the LTRs and LTAs. Planning is underway to implement this schedule.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of Thermal Diffusivity Degradation of Irradiated Zirlo and SiC-SiC Composite

Zirlo (Zircaloy cladding material from Westinghouse) has been widely used as the fuel cladding material in Light Water Reactors because of its high melting point, low susceptibility to corrosion, good thermal and mechanical shock resistance, and low degradation of mechanical properties under irradiation. But as Zirlo reacts with water at high temperature, which can trigger serious accidents, efforts have been made to explore better candidates to replace Zirlo in the water-cooled reactors. SiC-SiC composite is considered as one of the most viable options due to its comparable mechanical performances and corrosion resistance. However, one of the most important properties, thermal diffusivities of both Zirlo and SiC-SiC composite, and their degradation after irradiation, are not well known yet. Ion-irradiated samples are used to study the thermal property degradation caused by irradiation instead of the neutron-irradiated ones due to the significantly lower radioactivity. The microstructural damage is estimated from the software simulation SRIM/TRIM based on the energy and fluence of the ion, and the target material, and represented by DPA (displacement by atom). Different from neutron-irradiated samples, the damaged layer of ion-irradiated samples is only a few to a few tens of micrometers thick, and the damage is depth dependent. It is impossible to directly measure the bulk property change, and a microscale measurement technique is necessary. Laser-based photothermal reflectance technique is one of the ideal methods to measure local thermal conductivity and diffusivity with high spatial resolution. The main principle of this technique is to heat the solid sample using an intensity-modulated laser, and scan the sample with a constant intensity continuous-wave (CW) laser to detect the thermal wave propagation. On bulk, isotropic material, if the heating laser intensity is modulated as a sine wave, thermal diffusivity of the sample can be derived from the phase lag of the thermal wave, scan distance and modulation frequency in a straight forward manner. By using more specific analytical models, thermal conductivity and diffusivity in complicated cases, such as layered structure materials, composite materials, and/or anisotropic materials, are measurable as well. In this work, thermal diffusivity of the light damage layer of the post-irradiation Zirlo and SiC-SiC composite are measured and compared. The Zirlo sample is irradiated by Ni{sup 9+} ion, and SiC-SiC composite material is irradiated by Si{sup 7+} ion. The peak DPA of both sample is similar as ∼10. For ion-irradiated materials, DPA is known to increase with depth before it reaches the peak, and then sharply drop to zero. In term of light damage layer in this manuscript, we mean by the layer with a DPA smaller than 5% maximum value. In this layer DPA increases slowly and smoothly with depth, and the structure and thus thermal properties are more spatially uniform. For the SiC-SiC composite, the measurements are separately conducted on fibers along radial or axial direction, and on the matrix. Our measurement results show that with similar microstructural damage, thermal diffusivity of matrix SiC reduces more significantly than that of Zirlo. For fiber SiC that has a much lower thermal diffusivity than the matrix SiC before irradiation, the post-irradiation effect on thermal diffusivity is not obvious.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanisms of stored energy release in silicon carbide materials neutron-irradiated at elevated temperatures

Understanding the stored energy release behavior of SiC is crucial for the design of SiC-based fuel cladding for light water reactors because stored energy release affects response during accident conditions. Differential scanning calorimetry was used to evaluate the stored energy of monolithic SiC and SiC fiber–reinforced SiC matrix composite variants following neutron irradiation under light water reactor–relevant dose and temperature conditions. The tests were performed at heating rates of 0.5, 3, and 20 K/min up to 1,273 K. The onset temperature of the energy release roughly corresponded to the irradiation temperature, and energy release was delayed as the heating rate increased. The monolithic and composite specimens exhibited similar stored energy release behavior up to ~1,000 K, and above that temperature, the energy release depended more on material type. The energy release measured in this study is below the material-specific heat capacity at temperatures below ~1,000 K but exceeds it under certain material and annealing conditions at temperatures above ~1,000 K. The amount of irradiation-induced volumetric swelling of the specimens was an indication of the total stored energy. Based on this observation, the energy release behavior was described by a swelling recovery model.

36 MATERIALS SCIENCE↗

Post-irradiation examinations of UO 2 composites as part of the Accident Tolerant Fuels Campaign

Enhanced thermal conductivity uranium dioxide composites containing silicon carbide (UO 2 -SiC) and diamond (UO 2 -diamond) have been irradiated to low burnup. The conditions of this irradiation test and subsequent postirradiation examinations are discussed. These irradiations evaluate fuel microstructure and potential fuel cladding interaction under representative light water reactor power conditions. Both non-destructive and destructive techniques have been used to evaluate fuel integrity, fission gas release, fission product distribution, burnup, fuel swelling and cladding strain. Examination of the UO 2 -SiC pellets revealed enhanced cracking when compared to a UO 2 rodlet also irradiated under similar conditions. Additionally instability of the SiC whiskers in the uranium dioxide matrix was observed in the pellet central region, where the local temperatures exceeded 1300°C. The microstructure of the diamond-added UO 2 was severely disrupted during irradiation, resulting in local migration of cesium along the fuel stack and increased fission gas release when compared with the expected release from the Vitanza curve at corresponding values of burnup and irradiation temperature. The postirradiation examination results cast doubt on the suitability of these additives to improve UO 2 fuel performance in a way that would lead to enhanced accident tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear fuel cladding material

Silicon carbide (SiC)-based nuclear fission fuel rod cladding has been considered as one of the possible designs for accident tolerant fuels. It is in the form of a SiC fibre reinforced SiC matrix composite tube (SiC f -SiC m ) with monolithic SiC outer and/or inner coating layers. This study focuses on the deformation and fracture processes in this material using in situ X-ray micro-computed tomography (XCT) at room temperature (RT) and 1200 °C in an inert gas environment in a C-ring compression loading configuration. Prior to testing, local properties and residual stresses were characterised using nanoindentation and Raman spectroscopy since they can impact the mechanical behaviour of the material. The 3D strain distribution, crack formation and propagation processes including the toughening mechanisms (e.g., crack deflection, micro-cracking, crack bridging and bifurcation) are investigated in the coating and underlying composites at RT and 1200 °C. There is no particular sequence which toughening mechanism occurs first – this is very different from the conventional toughening theory in ceramic-matrix composites under uniaxial tension loading. Indeed, no evidence of fibre pull-out or fibre fracture was observed in this SiC f -SiC m nuclear cladding material in the current C-ring compression configuration. The correlation between local measurements and bulk mechanical behaviour are discussed.

3D imaging↗

Irradiation - High heat flux synergism in silicon carbide-based fuel claddings for light water reactors

Silicon carbide-based fuel cladding for light water reactors is anticipated to develop a unique stress state as a combined result from the high radial heat flux and irradiation-induced swelling assisted by thermal conductivity decrease. In order to verify the multi-physics finite-element analysis of this unique stress state, a novel experiment capturing the synergism of a high radiation field and a high radial heat flux in tubular silicon carbide specimens had been designed and implemented in the High Flux Isotope Reactor, Oak Ridge National Laboratory. In this experiment, small diameter tube test specimens made of monolithic or composite silicon carbide were irradiated to a dose of ∼2x10{sup 25} n/m{sup 2} (E > 0.1 MeV) under a radial heat flux of ∼0.6 MW/m{sup 2} while the outer surface temperature was maintained at a target temperature of about 300 Celsius degrees achieving a steep temperature gradient through the cladding wall thickness. The primary objective of the present paper is to discuss the technical planning and execution of the experiment. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation Examination of the ATF-1 Experiments - 2018 Status

The Advanced Fuels Campaign in collaboration with industry are working to develop enhanced accident tolerant fuels for light water reactors. The initial irradiations of these concepts were performed in the Idaho National Laboratory Advanced Test Reactor using simple drop-in style irradiations. These irradiations are collectively referred to as ATF 1. The postirradiation examination of ATF 1 has begun and some concepts have now completed initial examination. This report describes the results of examinations on ATF 1 irradiations designed to test the feasibility of enhancing UO 2 thermal conductivity with additives, ATF 1 irradiations of uranium silicide, and the current status of ATF 1 irradiations that are in process at the hot cell. Enhanced thermal conductivity uranium dioxide composites containing silicon carbide (UO 2 SiC) and diamond (UO 2 diamond) have been irradiated to low burnup. The conditions of this irradiation test and subsequent postirradiation examinations are discussed. These irradiations evaluate fuel microstructure and potential fuel cladding interaction under representative light water reactor power conditions. Both non destructive and destructive techniques have been used to evaluate fuel integrity, fission gas release, fission product distribution, burnup, fuel swelling and cladding strain. Examination of the UO 2 SiC pellets revealed enhanced cracking when compared to a UO 2 rodlet also irradiated under similar conditions. Additionally, instability of the SiC whiskers in the uranium dioxide matrix was observed in the pellet central region, where the local temperatures exceeded 1300 °C. The microstructure of the diamond added UO 2 was severely disrupted during irradiation, resulting in local migration of cesium along the fuel stack and increased fission gas release when compared with the expected release from the Vitanza curve at corresponding values of burnup and irradiation temperature. The postirradiation examination results cast doubt on the suitability of these additives to improve UO 2 fuel performance in a way that would lead to enhanced accident tolerance. Additionally, postirradiation examination data of U 3 Si 2 fuels at low burnup (i.e., < 20 GWd/tHM) for application in advanced Light Water Reactor (LWR) is presented. The U 3 Si 2 pellets show limited cracking in comparison to the expected behavior of UO 2 at same power level. In addition, gamma scanning data did not reveal migration of fission products. Minor homogeneous hardening along the pellet radius due to accumulation of fission products and radiation damage was measured by microindentation. The fission gas release and swelling remains very low. Formation of fission gas bubbles resolvable with optical microscopy occurs from the pellets center outward to approximately 60% of the fuel pellet radius. The overall data suggest a good performance of this accident tolerant fuel candidate at low burnup. Finally, the current status of postirradiation examination on other ATF 1 irradiations will be discussed. These irradiations include UO 2 clad in an FeCrAl alloy, an alternative uranium silicide compound U 3 Si 5 also clad in a FeCrAl alloy, and an interaction test between UO 2 and different FeCrAl alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗