SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ultrafiltration membrane with high-temperature capability prepared from polyimide soluble in organic solvent such as dimethylacetamide, made in single step by solution-casting phase inversion.
A method and a product for protecting semiconductor surfaces is disclosed. The protective coating material is prepared by heating a suitable protective resin with an organic solvent which is solid at room temperature and converting the resulting solution into sheets by a conventional casting operation. Pieces of such sheets of suitable shape and thickness are placed on the semiconductor areas to be coated and heat and vacuum are then applied to melt the sheet and to drive off the solvent and cure the resin. A uniform adherent coating, free of bubbles and other defects, is thus obtained exactly where it is desired.
Substrate morphology has a significant effect on the CO 2 transport performance of a thin-film composite (TFC) membrane. In this study, a new mixed solvent comprising 2-pyrrolidone (2-PD) and 2-methoxyethanol (2-ME) was used to prepare polyethersulfone (PES) substrates with bicontinuous structure by water vapor-induced phase separation, followed by immersion in water as nonsolvent. Here, compared with the commonly used solvent, N-methyl-2-pyrrolidone (NMP), the 2-PD/2-ME mixed solvent is more hydrophilic and can decrease the thermodynamic stability of the casting solution significantly. As a result, the phase separation was induced via the spinodal decomposition mechanism. The open morphology bestowed the optimized substrate with a very high CO 2 permeance of 133,226 ± 3,870 GPU (1 GPU = 10 –6 cm 3 (STP) s –1 cm –2 cmHg –1 = 3.3464 × 10 -9 kg-mol s –1 m –2 Pa –1 ), which was 5 times more permeable than the baseline substrate synthesized with NMP. By using this new substrate, the prepared TFC membrane containing amines showed an increased CO 2 permeance of 908 ± 8 GPU at 57°C, which was 48 GPU higher than that with the baseline substrate. Meanwhile, the CO 2 /N 2 selectivity was retained at 162 ± 4 at 57°C. In addition, the good scalability of the new PES substrate was demonstrated by roll-to-roll fabrication of a 50' long scale-up PES substrate with a width of 21".
Experiments have shown the stability enhancement of polymeric sensing films on mixing the polymer with colloidal filler particles (submicron-sized) of carbon black, silver, titanium dioxide, and fumed silicon dioxide. The polymer films are candidates for potential use as sensing media in micro/nano chemical sensor devices. The need for stability enhancement of polymer sensing films arises because such films have been found to exhibit unpredictable changes in sensing activity over time, which could result in a possible failure of the sensor device. The changes in the physical properties of a polymer sensing film caused by the sorption of a target molecule can be measured by any of several established transduction techniques: electrochemical, optical, calorimetric, or piezoelectric, for example. The transduction technique used in the current polymer stability experiments is based on piezoelectric principles using a quartz-crystal microbalance (QCM). The surface of the QCM is coated with the polymer, and the mass uptake by the polymer film causes a change in the oscillating frequency of the quartz crystal. The polymer used for the current study is ethyl cellulose. The polymer/ polymer composite solutions were prepared in 1,3 dioxolane solvent. The filler concentration was fixed at 10 weight percent for the composites. The polymer or polymer composite solutions were cast on the quartz crystal having a fundamental frequency of about 6 MHz. The coated crystal was subjected to a multistage drying process to remove all measurable traces of the solvent. In each experiment, the frequency of oscillation was measured while the QCM was exposed to clean, dry, flowing air for about 30 minutes, then to air containing a known concentration of isopropanol for about 30 minutes, then again to clean dry air for about 30 minutes, and so forth. This cycle of measurements for varying isopropanol concentrations was repeated at intervals for several months. The figure depicts some of the sensing film stability results for ethyl cellulose polymer, ethyl cellulose-carbon black, and ethyl cellulose-silicon dioxide composite systems. An ethyl cellulose film exhibited a marked decline in response in the first few months of study and settled to a steady average response after about four months. However, response varied widely around the average response for ethyl cellulose film. In contrast, ethyl cellulose- carbon black and ethyl cellulose-silicon dioxide composites also declined in the early months, but showed more repeatable sensing film activity after the initial decline. Similar trends were observed in experiments for ethyl cellulose-titanium dioxide and ethyl cellulose-silver composites.
This study deals with the modification of polyphenylsulfone ultrafiltration membranes by introduction of an incompatible polymer polysulfone to the polyphenylsulfone casting solution to improve the permeability. The correlation between properties of the blend polyphenylsulfone/polysulfone solutions and porous anisotropic membranes for ultrafiltration prepared from these solutions was revealed. The blend polyphenylsulfone/polysulfone solutions were investigated using a turbidity spectrum method, optical microscopy and measurements of dynamic viscosity and turbidity. The structure of the prepared blend flat sheet membranes was studied using scanning electron microscopy. Membrane separation performance was investigated in the process of ultrafiltration of human serum albumin buffered solutions. It was found that with the introduction of polysulfone to the polyphenylsulfone casting solution in N-methyl-2-pyrrolidone the size of supramolecular particles significantly increases with the maximum at (40–60):(60:40) polyphenylsulfone:polysulfone blend ratio from 76 nm to 196–354 nm. It was shown that polyphenylsulfone/polysulfone blend solutions, unlike the solutions of pristine polymers, are two-phase systems (emulsions) with the maximum droplet size and highest degree of polydispersity at polyphenylsulfone/polysulfone blend ratios (30–60):(70–40). Pure water flux of the blend membranes passes through a maximum in the region of the most heterogeneous structure of the casting solution, which is associated with the imposition of a polymer-polymer phase separation on the non-solvent induced phase separation upon membrane preparation. The application of polyphenylsulfone/polysulfone blends as membrane-forming polymers and polyethylene glycol (Mn = 400 g·mol -1 ) as a pore-forming agent to the casting solutions yields the formation of ultrafiltration membranes with high membrane pure water flux (270 L·m -2 ·h -1 at 0.1MPa) and human serum albumin rejection of 85%.
The undesirable buildup of ice can compromise the operational safety of ships in the Arctic to high-flying airplanes, thereby having a detrimental impact on modern life in cold climates. The obstinately strong adhesion between ice and most functional surfaces makes ice removal an energetically expensive and dangerous affair. Hence, over the past few decades, substantial efforts have been directed toward the development of passive ice-shedding surfaces. Conventionally, such research on ice adhesion has almost always been based on ice solidified from pure water. However, in all practical situations, freezing water has dissolved contaminants; ice adhesion studies of which have remained elusive thus far. Here, in this work, we cast light on the fundamental role played by various impurities (salt, surfactant, and solvent) commonly found in natural water bodies on the adhesion of ice on common structural materials. We elucidate how varying freezing temperature & contaminant concentration can significantly alter the resultant ice adhesion strength making it either super-slippery or fiercely adherent. The entrapment of impurities in ice changes with the rate of freezing and ensuing adhesion strength increases as the cooling temperature decreases. We discuss the possible role played by the in situ generated solute enriched liquid layer and the nanometric water-like disordered ice layer sandwiched between ice and the substrate behind these observations. Our work provides useful insights into the elementary nature of impure water-to-ice transformation and contributes to the knowledge base of various natural phenomena and rational design of a broad spectrum of anti-icing technologies for transportation, infrastructure, and energy systems.
The growing demand for high-energy, low-cost lithium-ion batteries (LIBs) to power electric vehicles (EVs) necessitates advances in both materials and manufacturing processes. Conventional cathode fabrication methods, such as slurry casting and drying, are energy-intensive and pose challenges for scalability and environmental compliance. In this study, we propose cold-spray (CS) deposition as a solvent-free approach for fabricating LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) composite cathodes. Powder blends of NMC622, poly(vinylidene fluoride) (PVDF), and carbon black (CB) are directly deposited onto stainless steel and Inconel substrates under varied gas temperatures, pressures (and thus velocities), and standoff distances. The effects of temperature on the deposit morphology, coating density, and volume are systematically investigated. Computational fluid dynamics simulations reveal that increasing the gas temperature enhances the particle velocity, narrows the spray angle, and reduces the mass concentration radially at the nozzle outlet. CS deposition results in a dense cathode microstructure, accompanied by fracture in polycrystalline NMC622 particles. X-ray diffraction analysis further verifies that there are no phase changes during the deposition process. The electrochemical performance of the cold-sprayed cathodes reveals an initial capacity of approximately 96 mAh g –1 for single-crystal NMC622 and 167 mAh g –1 for polycrystalline NMC622. While these values are modest compared to state-of-the-art slurry-cast cathodes, which typically exhibit 180–200 mAh g –1 under optimized conditions. The results demonstrate a competitive performance given the solvent-free nature of the CS process and compare favorably with tape-cast samples made from identical feedstock. In conclusion, he CS process enables the formation of dense, binder-integrated cathode coatings without the need for solvent processing, offering a promising pathway for scalable, energy-efficient dry electrode manufacturing of next-generation LIBs.
Because of its high reactivity, atomic oxygen causes surface erosion on polymeric materials. although the reaction efficiency depends on the chemical structure of the polymer. We have found an organotin compound, bis(triphenyltin) oxide (BTO), which has an unusually high solubility in solutions of a number of commercial high performance polymers. Films of these polymers containing BTO showed a substantial reduction in erosion by atomic oxygen when compared with films of the pure material. Analysis has shown that in the presence of atomic oxygen, erosion of the exposed surfaces of the BTO-containing films leaves a residual protective tin oxide coating . Since the additive is uniformly distributed throughout the polymeric material, any break or puncture in the protective coating is "healed" by the material below. Samples were exposed to the environment of the low earth orbit (LEO) on two Space Shuttle flights, STS-46, in June of 1992, and STS-51 in September of 1993. The analysis of these samples has been reported previously. For both flights, the samples were small (1.3 cm and 1.9 cm respectively) thus limiting the scope of analysis. In the research under this cooperative agreement, films of a polyetherimide, were exposed to the LEO environment on Space Shuttle flight STS-85 in August of 1997 as part of the Evaluation of Space Environment and Effects on Materials (ESEM) experiment. The polyetherimide chosen is available commercially as Ultem, registered to the General Electric Company. Films of pure Ultem, Ultem with 10% BTO by mass, and Ultem with 20% BTO by mass were exposed in the ram direction for 40 hours during STS-85. Ultem has a Tg of 215 deg C and is soluble in common chlorinated solvents. Granules of the polymer were dried at 120 deg C, but otherwise were used as received. Films were cast on a glass plate from a solution of the polymer in a 60/40 (w/w) mixture of chloroform and 1,1,2,2-tetrachloroethane. The plate was placed in a dust-free box for at least 24 hours to allow much of the solvent to evaporate, and then was moved to a vacuum oven and slowly heated from 20 to 220 deg C over a period of two weeks to completely remove all solvent. Each exposed sample was 7.6 cm long and 2.2 cm wide and about 0.025 mm thick. The structures of Ultem and bis(triphenyltin) oxide are shown.
Soluble metalinked poly(imide siloxane) segmented copolymers were synthesized utilizing a THF/NMP cosolvent system. The presence of dual solvent makes it possibled to reach high molecular weight in the amid acid stage. Incorporation of siloxanes at about 10 weight percent or higher enables the materials to be fully soluble in a range of polar solvents even after imidization. Imidization may be achieved either by conventional thermal methods on cast amic acid films or in appropriate solvent/azeotroping-agent systems employing moderate temperatures. The imidization procedure has been followed by FT-IR and NMR studies. FT-IR studies show the solution imidization follows first order kinetics and proceeds to about 96 percent completion. NMR studies of the isolated products show residual amic acid may be present after solution imidization, but only at very low levels. Properties of the solution imidized materials compared well with those obtained from samples imidized as thin films.
A family of polymer/carbon films has been developed for use as sensory films in electronic noses for detecting SO2 gas at concentrations as low as 1 part per million (ppm). Most previously reported SO2 sensors cannot detect SO2 at concentrations below tens of ppm; only a few can detect SO2 at 1 ppm. Most of the sensory materials used in those sensors (especially inorganic ones that include solid oxide electrolytes, metal oxides, and cadmium sulfide) must be used under relatively harsh conditions that include operation and regeneration at temperatures greater than 100 C. In contrast, the present films can be used to detect 1 ppm of SO2 at typical opening temperatures between 28 and 32 C and can be regenerated at temperatures between 36 and 40 C. The basic concept of making sensing films from polymer/carbon composites is not new. The novelty of the present family of polymer/carbon composites lies in formulating the polymer components of these composites specifically to optimize their properties for detecting SO2. First-principles quantum-mechanical calculations of the energies of binding of SO2 molecules to various polymer functionalities are used as a guide for selecting polymers and understanding the role of polymer functionalities in sensing. The polymer used in the polymer-carbon composite is a copolymer of styrene derivative units with vinyl pyridine or substituted vinyl pyridine derivative units. To make a substituted vinyl pyridine for use in synthesizing such a polymer, poly(2-vinyl pyridine) that has been dissolved in methanol is reacted with 3-chloropropylamine that has been dissolved in a solution of methanol. The methanol is then removed to obtain the copolymer. Later, the copolymer can be dissolved in an appropriate solvent with a suspension of carbon black to obtain a mixture that can be cast and then dried to obtain a sensory film.
Polyimides of a recently developed type have an attractive combination of properties, including low solar absorptivity (manifested as low color) when cast into thin films, resistance to atomic oxygen and ultraviolet radiation, solubility in organic solvents, high glass-transition temperatures, and high thermal stability. The focus of the development work was on polymers that can endure the space environment and that have specific combinations of properties for use on Gossamer spacecraft. Because of their unique combination of properties, these polymers are also expected to find use in a variety of other applications on Earth as well as in space. Examples of other space applications include membranes on antennas, second-surface mirrors, thermal optical coatings, and multilayer thermal insulation. For both terrestrial and space applications, these polyimides can be processed into various forms, including films, fibers, foams, threads, adhesives, and coatings.
Most previous studies about halide solid-state electrolytes have used pellets prepared by uniaxial pressing, which is a good approach for materials development but is not suitable for commercialization. Thinner electrolyte layers that can be scaled up to large cell areas are required, and tape casting is a promising approach. It is challenging, however, as halide materials are reactive with most of the conventional solvents used in the process. In this study, solvents with low polarity, such as toluene, are found to be compatible with the Li 3 YBr 6 halide material. A wide variety of candidate binders that are soluble in toluene are studied. MSB1–13 binder is preferred, based on the ionic conductivity and mechanical properties of the tape. Electrolyte tapes (<70 μ m) are successfully cast on Al substrates, using 2 wt% binder. The resulting room temperature ionic conductivity is 2 × 10 −4 S cm −1 . Two composite cathodes including active material (LiFePO 4 or LiNi 0.82 Mn 0.07 Co 0.11 O 2 ) and 1 to 1.5 wt% MSB1–13 are tape cast as proof-of-concept for a scalable cell fabrication approach. A LiFePO 4 cell shows good retention at 25 °C. The performance of NMC cells with tape electrolyte or pellet electrolyte is similar. This study demonstrates the feasibility of tape casting halide-based electrolytes and cathodes.
Solvent-free manufacturing of battery components is a promising alternative to traditional slurry processing for reducing the cost and environmental impact. In this work, we used twin-screw melt extrusion to fabricate a polymer-based high voltage composite cathode. The melt-processed cathode is dense (near zero porosity) and thick (65 μm) and has high active material loading (80 wt %). The active particles are distributed uniformly throughout the melt-processed cathode, unlike the traditional slurry-cast cathode, which exhibits inhomogeneous particle distribution. In the melt-processed cathode, polymer and carbon form separate phases, whereas in the slurry-cast cathode they blend into a single phase. Due to these structural differences, the melt-processed cathode shows smooth charge–discharge profiles, while the slurry-cast cathode shows noisy charging and soft-shorting behavior. In conclusion, this work highlights that twin-screw extrusion as a scalable, solvent-free manufacturing method is advantageous in producing uniform cathodes, which mitigates anode instability.
Here, using theoretical modeling to guide our approach, substituents were selected to improve the negative and positive potentials associated with a representative metal-based redox carrier, a phenyl spaced nickel bispicolinamide complex, [Ni(bpb)], 1. To broaden the cell potential, electron donating groups were selected and installed on the pyridyl moieties, [Ni(bpb-(NMe 2 ) 2 )], 2, while electron withdrawing groups were incorporated on the phenyl linker, [Ni(bpb-R)] (R = –F, –CF 3 , and –NO 2 ), 3–5. Our model predicts an increase of ~300 mV and ~500 mV for the first and second negative waves of Ni(bpb-NMe 2 ), 2, and up to ~330 mV and ~210 mV increase to the first and second positive waves in 3–5. The modeled complexes were synthesized in good yields using a modification of the literature procedure. Due to limited solubility, the differential pulse voltammetry was measured on complexes 2–5 using a drop cast technique. Comparison of the observed and predicted potentials is discussed in acetonitrile (MeCN) and dimethylformamide (DMF) solvents.
Infrared and Raman spectroscopy techniques were applied to investigate the drying and aggregation behavior of Nafion ionomer particles dispersed in aqueous solution. Gravimetric measurements aided the identification of gel-phase development within a series of time-resolved spectra that tracked transformations of a dispersion sample during solvent evaporation. A spectral band characteristic of ionomer sidechain end group vibration provided a quantitative probe of the dispersion-to-gel change. For sets of attenuated total reflection Fourier transform infrared (ATR FT-IR) spectra, adherence to Beer's law was attributed to the relatively constant refractive index in the frequency region of hydrated –SO$^{–}_{3}$ group vibrations as fluorocarbon-rich ionomer regions aggregate in forming the structural framework of membranes and thin films. Although vibrational bands associated with ionomer backbone CF 2 stretching vibrations were affected by distortion characteristic of wavelength-dependent refractive index change within a sample, the onset of band distortion signaled gel formation and coincided with ionomer mass % values just below the critical gelation point for Nafion aqueous dispersions. Similar temporal behavior was observed in confocal Raman microscopy experiments that monitored the formation of a thin ionomer film from an individual dispersion droplet. For the ATR FT-IR spectroscopy and confocal Raman microscopy techniques, intensity in the water H–O–H bending vibrational band dropped sharply at the ionomer critical gelation point and displayed a time dependence consistent with changes in water content derived from gravimetric measurements. The reported studies lay groundwork for examining the impact of dispersing solvents and above-ambient temperatures on fluorinated ionomer transformations that influence structural properties of dispersion-cast membranes and thin films.
A low enriched U-Mo alloy fuel is under development to replace highly enriched U fuels currently used in United States high performance research reactors. The alloy casting and fuel fabrication processes will generate scrap streams containing low enriched U (LEU) which must be recovered. Solvent extraction processes were designed using the Argonne Model for Universal Solvent Extraction (AMUSE) to purify solutions containing 20 and 50 g/L U. The feed for the solvent extraction processes was prepared from solutions generated from the dissolution of U-10Mo-Zr foils and U-10Mo-Zr-Al mini-plates. The U purification processes were demonstrated using two, 16-stage banks of miniature mixer-settlers. The solvent extraction experiments demonstrated that all design objectives for the U purification processes could be met. The U recovery in the product stream for each flowsheet was ≥99.9%. The flowsheet demonstrations also showed that the purity of the U Product will meet the requirements of the ASTM International C1462-21 specification for LEU metal enriched to less than 20% 235 U. In conclusion, the AMUSE modeling for both flowsheet demonstrations was validated by comparing predicted and measured concentrations of U, Mo, and Zr in the exit streams and stage samples at steady-state conditions in the mixer-settlers.
Slurry compositions, tape casting binder systems and fabrication methods for the fabrication of lithium-garnet electrolyte scaffolds for use in solid state batteries and other devices are provided. Slurry compositions may be optimized mixtures of LLZO powder, a dispersant, a lithium salt, a wetting agent a binder, a plasticizer and at least one solvent. The optimized ceramic slurry compositions may include MgO as a sintering additive to improve density and ionic conductivity of the doped-LLZO sheets and produce a fine-grained microstructure. Sintering protocols for cast slurries of commercially available doped LLZO powders eliminate the requirement of mother-powder coverings or externally applied pressure. An environmentally friendly water-based system using methylcellulose as a binder is also provided producing green tape and final properties comparable to those obtained with organic solvent-based systems.
Microbes inhabiting complex porous microenvironments in sediments and aquifers catalyze reactions that are critical to global biogeochemical cycles and ecosystem health. However, the opacity and complexity of porous sediment and rock matrices have considerably hindered the study of microbial processes occurring within these habitats. Here, we generated microbially compatible, optically transparent mineral scaffolds to visualize and investigate microbial colonization and activities occurring in these environments, in laboratory settings and in situ. Using inexpensive synthetic cryolite mineral, we produced optically transparent scaffolds mimicking the complex 3D structure of sediments and rocks by adapting a suspension-based, freeze-casting technique commonly used in materials science. Fine-tuning of parameters, such as freezing rate and choice of solvent, provided full control of pore size and architecture. The combined effects of scaffold porosity and structure on the movement of microbe-sized particles, tested using velocity tracking of fluorescent beads, showed diverse yet reproducible behaviors. The scaffolds we produced are compatible with epifluorescence microscopy, allowing the fluorescence-based identification of colonizing microbes by DNA-based staining and fluorescence in situ hybridization (FISH) to depths of 100 µm. Additionally, Raman spectroscopy analysis indicates minimal background signal in regions used for measuring deuterium and 13 C enrichment in microorganisms, highlighting the potential to directly couple D 2 O or 13 C stable isotope probing and Raman-FISH for quantifying microbial activity at the single-cell level. To demonstrate the relevance of cryolite scaffolds for environmental field studies, we visualized their colonization by diverse microorganisms within rhizosphere sediments of a coastal seagrass plant using epifluorescence microscopy. The tool presented here enables highly resolved, spatially explicit, and multimodal investigations into the distribution, activities, and interactions of underground microbes typically obscured within opaque geological materials until now.