Search NASA⌕ Search

SEARCH · Search NASA

Results for “Spalling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Three-Dimensional Characterization and Modeling of Microstructural Weak Links for Spall Damage in FCC Metals

Local microstructural weak links for spall damage were investigated using three-dimensional (3-D) characterization in multicrystalline copper samples (grain size ≈ 450 µm) shocked with laser-driven plates at low pressures (2 to 4 GPa). The thickness of samples and flyer plates, approximately 1000 and 500 µm respectively, led to short pressure pulses that allowed isolating microstructure effects on local damage characteristics. Electron Backscattering Diffraction and optical microscopy were used to relate the presence, size, and shape of porosity to local microstructure. The experiments were complemented with 3-D finite element simulations of individual grain boundaries (GBs) that resulted in large damage volumes using crystal plasticity coupled with a void nucleation and growth model. Results from analysis of these damage sites show that the presence of a GB-affected zone, where strain concentration occurs next to a GB, correlates strongly with damage localization at these sites, most likely due to the inability of maintaining strain compatibility across these interfaces, with additional effects due to the inclination of the GB with respect to the shock. Results indicate that strain compatibility plays an important role on intergranular spall damage in metallic materials.

36 MATERIALS SCIENCE↗

Demonstration of GaAs-Based Photovoltaics on Acoustically Spalled Surfaces Grown by MOCVD

This study demonstrates the potential of sonic lift-off (SLO) technology for repeatable substrate reuse in gallium arsenide (GaAs)–based photovoltaics (PVs), offering a pathway toward cost effective production for terrestrial PV applications. Single-junction GaAs solar cells fabricated on acoustically spalled substrates achieved performance metrics comparable with those grown on standard commercial substrates, exhibiting short-circuit current densities (J sc ) of approximately 26.2–26.4 mA/cm 2 , open-circuit voltages (V oc ) around 1001 mV, fill factors (FFs) of 84%, and AM1.5G efficiencies near 22%. These results confirm that one reuse cycle can be realized without a performance penalty, offering a direct pathway to reducing substrate cost in fabrication. Furthermore, subsequent reuse of the substrates highlighted critical challenges, as devices fabricated from reused substrates showed significant degradation in performance (J sc of 15.5 mA/cm 2 , V oc of 748 mV, FF of 72%, and efficiency of 8%), primarily due to degradation of the epitaxial structure resulting from repeated spalling cycles.

Acoustic Spalling↗

Cylinder Test Correction for Copper Work Hardening and Spall

As a basis for the corrections to be discussed, an analytical equation is first presented for calculating detonation energy densities from copper wall velocities in the Cylinder test. Steinberg-Guinan work hardening is sufficient for the Cylinder problem, between 1 and 60 GPa, with a change of Y o to 0.10 kJ cm –3 for annealed copper. An air gap correction was the first to be applied, which is a function of the initial air gap width and the tilt angle of the cylinder. Irreversible heat loss was also found to be a small error. Spall is calibrated using new copper gun shot data and this energy is also small. The model up through work hardening agrees with the code, which does not contain heat loss or spall, both of which equal the error of repetitive calculation. In conclusion, the effect of the many additions to the original Gurney energy is shown.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Correlations Between Spall Damage Mode Preference and Microstructure in Shocked Polycrystalline Copper: A 3-D X-Ray Tomography Study

Nondestructive characterization techniques are essential for maximizing the amount of high fidelity data obtained from post mortem mechanically tested materials, particularly for the complex experimental techniques used for shock loading. Polycrystalline copper samples of varying thermomechanical histories were shock loaded to induce incipient spall damage conditions via plate impacts at low pressures. Electron backscattering diffraction (EBSD) and 3-D X-ray tomography (XRT) were utilized to obtain microstructural and void volume data, respectively. Voids were fit to ellipsoids using their inertia tensors obtained from the 3-D XRT data, and the results compared to EBSD data. This, in turn, enabled establishing quantitative correlations between void shapes and preferential damage mode, either inter- or trans-granular, for each thermomechanical history. Greater than 60 % of voids present in heat-treated samples were spherical, indicative of transgranular damage preference. Greater than 90 % of voids present in as-received rolled samples were flat sheetlike voids or unsymmetrical oblate ellipsoids, indicative of intergranular and coalesced damage modes. Analyzing grain boundary damage statistics in conjunction with global damage mode distributions indicate that boundaries become less dominant as preferential void nucleation sites within the spall plane as the bulk strength of the material decreases from heat treatments.

Microstructure↗

High-Strain Rate Spall Strength Measurement for CoCrFeMnNi High-Entropy Alloy

In this study, we experimentally investigate the high stain rate and spall behavior of Cantor high-entropy alloy (HEA), CoCrFeMnNi. First, the Hugoniot equations of state (EOS) for the samples are determined using laser-driven CoCrFeMnNi flyers launched into known Lithium Fluoride (LiF) windows. Photon Doppler Velocimetry (PDV) recordings of the velocity profiles find the EOS coefficients using an impedance mismatch technique. Following this set of measurements, laser-driven aluminum flyer plates are accelerated to velocities of 0.5–1.0 km/s using a high-energy pulse laser. Upon impact with CoCrFeMnNi samples, the shock response is found through PDV measurements of the free surface velocities. From this second set of measurements, the spall strength of the alloy is found for pressures up to 5 GPa and strain rates in excess of 106 s−1. Further analysis of the failure mechanisms behind the spallation is conducted using fractography revealing the occurrence of ductile fracture at voids presumed to be caused by chromium oxide deposits created during the manufacturing process.

36 MATERIALS SCIENCE↗

Morphology Control of Growth by Hydride Vapor Phase Epitaxy on Faceted GaAs Substrates Produced by Controlled Spalling for Low Cost III-V Devices

In this work, we apply the morphology control of hydride vapor phase epitaxial (HVPE) growth to planarize faceted, non-planar substrates. Controlled spalling is a promising high-throughput substrate reuse technology that could reduce substrate costs for III-V devices; however, the spalling fracture for (100)-oriented GaAs substrates produces a regularly corrugated surface of facets that are 5-20 um in height. We discuss how to planarize these surfaces using only a few minutes of HVPE growth and how to minimize the impact on throughput when integrating faceted wafers into a potential manufacturing process at scale.

epitaxy↗

Spall damage of a Ta particle-reinforced metallic glass matrix composite under high strain rate loading

We investigate deformation and damage of a Zr-based bulk metallic glass (BMG) and its Ta particle-reinforced composite (MGMC) under impact loading, as well as quasi-static tension for comparison. Yield strength, spall strength, and damage accumulation rate are obtained from free-surface velocity histories, and MGMC appears to be more damage-resistant. Scanning electron microscopy, electron back scattering diffraction and x-ray computed tomography, are utilized for characterizing microstructures, which show features consistent with macroscopic measurements. Different damage and fracture modes are observed for BMG and MGMC. Multiple well-defined spall planes are observed in BMG, while isolated and scattered cracking around reinforced particles dominates fracture of MGMC. Particle–matrix interface serves as the source and barrier to crack nucleation and propagation under both quasi-static and impact loading. Finally, deformation twinning and grain refinement play a key role in plastic deformation during shock loading but not in quasi-static loading. In addition, 3D cup-cone structures are resolved in BMG, but not in MGMC due to its heterogeneous stress field.

36 MATERIALS SCIENCE↗

Twin boundary spacing effects on shock response and spall behaviors of hierarchically nanotwinned fcc metals

Atomistic deformation mechanisms of hierarchically nano-twinned (NT) Ag under shock conditions have been investigated using a series of large-scale molecular dynamics simulations. For the same grain size d and the same spacing of primary twins λ{sub 1}, the average flow stress behind the shock front in hierarchically NT Ag first increases with decreasing spacing of secondary twins λ{sub 2}, achieving a maximum at a critical λ{sub 2}, and then drops as λ{sub 2} decreases further. Above the critical λ{sub 2}, the deformation mechanisms are dominated by three type strengthening mechanisms: (a) partial dislocations emitted from grain boundaries (GBs) travel across other boundaries; (b) partial dislocations emitted from twin boundaries (TBs) travel across other TBs; (c) formation of tertiary twins. Below the critical λ{sub 2}, the deformation mechanism are dominated by two softening mechanisms: (a) detwinning of secondary twins; (b) formation of new grains by cross slip of partial dislocations. Moreover, the twin-free nanocrystalline (NC) Ag is found to have lower average flow stress behind the shock front than those of all hierarchically NT Ag samples except the one with the smallest λ{sub 2} of 0.71 nm. No apparent correlation between the spall strength and λ{sub 2} is observed in hierarchically NT Ag, since voids always nucleate at both GBs and boundaries of the primary twins. However, twin-free NC Ag is found to have higher spall strength than hierarchically NT Ag. Voids can only nucleate from GBs for twin-free NC Ag, therefore, twin-free NC Ag has less nucleation sources along the shock direction when compared to hierarchically NT Ag, which requiring higher tensile stress to create spallation. These findings should contribute to the understandings of deformation mechanisms of hierarchically NT fcc metals under extreme deformation conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thin silicon foils produced by epoxy-induced spalling of silicon for high efficiency solar cells

We report on the drastic improvement of the quality of thin silicon foils produced by epoxy-induced spalling. In the past, researchers have proposed to fabricate silicon foils by spalling silicon substrates with different stress-inducing materials to manufacture thin silicon solar cells. However, the reported values of effective minority carrier lifetime of the fabricated foils remained always limited to ∼100 μs or below. In this work, we investigate epoxy-induced exfoliated foils by electron spin resonance to analyze the limiting factors of the minority carrier lifetime. These measurements highlight the presence of disordered dangling bonds and dislocation-like defects generated by the exfoliation process. A solution to remove these defects compatible with the process flow to fabricate solar cells is proposed. After etching off less than 1 μm of material, the lifetime of the foil increases by more than a factor of 4.5, reaching a value of 461 μs. This corresponds to a lower limit of the diffusion length of more than 7 times the foil thickness. Regions with different lifetime correlate well with the roughness of the crack surface which suggests that the lifetime is now limited by the quality of the passivation of rough surfaces. The reported values of the minority carrier lifetime show a potential for high efficiency (>22%) thin silicon solar cells.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Spall Strength and Dynamic Yield Stress of Hafnium

The spall strength and dynamic yield stress of polycrystalline hafnium have been measured in a series of plane-wave shock loading experiments using flat sample–transparent window composite targets, with the transparent windows representing polymethyl methacrylate or lithium fluoride plates arranged on the rear side of a hafnium sample. The front side of the target was subjected to shock impact of a copper striker, the rear surface velocity was measured, and the sample was recovered for subsequent metallographic examination. The results were also used for evaluation of the accuracy of spall strength measurements and the analysis of features of high-rate deformation of hafnium.

36 MATERIALS SCIENCE↗

Auger Spectroscopy Analysis of Spalled LEU-10Mo Foils

Presentation includes slides on Surface Science used to probe LEU-10Mo Spall; Auger highlights graphitic-like inclusions and Mo-deficient oxide on base metal; Higher C concentration detected within spall area Images Courtesy; Depth profiling reveals thick oxide; Mo concentration nears nominal only at depths ~400 nm; and lastly Key Findings.

36 MATERIALS SCIENCE↗

The role of elastic and plastic anisotropy in intergranular spall failure

Recent mesoscale experimental observations of dynamic ductile failure have demonstrated a strong relationship between grain boundary (GB) misorientation and the likelihood of failure initiation along said GB. This correlation has been attributed to inherent GB weakness of particular misorientation. Here we discuss the role played by mechanics, i.e. elastic and plastic anisotropy, on the experimental observation. We make use of a recently developed framework for modeling dislocation-based crystal plasticity and ductile failure of single crystals under dynamic loading (CPD-FE). Polycrystals are studied at the mesoscale level through the explicit resolution of individual grains, i.e. resolving each individual grain's size, shape, and orientation. In our simulations, failure naturally localizes along the GBs with no necessity for ad hoc rules governing damage nucleation. We carry out a few thousand mesoscale calculations, systematically varying the misorientation angles of the GB in the computational microstructure. Despite the fact that we neglect the possibility of variations in inherent GB weakness, our simulations agree favorably with the experimental observations, implying that stress concentration generated by elastic and plastic anisotropies across GBs is a dominant governing factor in this phenomenon. Lastly, we find that misorientation angle is an insufficient GB descriptor to predict the likelihood of intergranular spall failure, which is better understood through the consideration of additional GB degrees of freedom.

36 MATERIALS SCIENCE↗

A metallography and x-ray tomography study of spall damage in ultrapure Al

We characterize spall damage in shock-recovered ultrapure Al with metallography and x-ray tomography. The measured damage profiles in ultrapure Al induced by planar impact at different shock strengths, can be described with a Gaussian function, and showed dependence on shock strengths. Optical metallography is reasonably accurate for damage profile measurements, and agrees within 10–25% with x-ray tomography. Full tomography analysis showed that void size distributions followed a power law with an exponent of γ = 1.5 ± 2.0, which is likely due to void nucleation and growth, and the exponent is considerably smaller than the predictions from percolation models.

36 MATERIALS SCIENCE↗

Spall strength of additively repaired 304L stainless steel

Additive manufacturing has the potential to repair damaged parts, but the performance of additive materials under high strain rate loading is still uncertain—especially with the added complexity of an interface with an existing wrought material. In this work, 304L stainless steel samples were intentionally damaged and then repaired with wire-fed laser additive manufacturing. The samples were subjected to shock loading to generate incipient spall. Velocimetry and post-mortem metallography results show that when the additive repair process parameters are optimized to reduce porosity and match the equation of state of the original material, the influence of the repair region on the shock propagation is negligible. In conclusion, the free-surface velocity profile and internal damage morphology of the repaired sample are shown to be practically identical to the pristine material.

36 MATERIALS SCIENCE↗

Influence of nanoscale interfaces on the dynamic deformation and spall failure of Cu–Fe alloy microstructures

Additively manufactured immiscible Cu–Fe alloys can exhibit a distribution of nanoscale interfaces due to the distribution of nanoscale clusters in the equilibrium and metastable phases. Molecular dynamics simulations investigate the role of such interfaces on the phase stability and transformation behavior during shock compression, as well as the mechanisms of damage nucleation during spall failure. The model multiphase Cu–Fe systems studied here comprise a distribution of Fe clusters in an FCC Cu matrix, as well as Cu clusters in a BCC Fe matrix. The length scales of the nanoscale clusters determine the energetics of the interfaces that can result in FCC/BCC (equilibrium) or FCC/FCC (metastable) interfaces in the Cu system matrix, and BCC/FCC (equilibrium) or BCC/BCC (metastable) interfaces in the Fe matrix. The MD simulations demonstrate that nanoscale metastable interface microstructures can induce plastic deformation and also stabilize phases or suppress phase transformations in metastable phase clusters. In contrast, equilibrium interfaces can influence phase transformation thresholds and serve as additional void nucleation sites during failure.

36 MATERIALS SCIENCE↗

Shock-induced twinning/detwinning and spall failure in Cu–Ta nanolaminates at atomic scales

Here, this study provides new insights into the role of interfaces on the deformation and failure mechanisms in shock-loaded Cu–Ta–Cu trilayer system. The thickness of the Ta layer, piston velocities, and shock pulse durations were varied to explore the impact of impedance mismatch and loading conditions on spallation behavior and twin formation. It was found that the interfaces play a crucial role in the dynamic response of these multilayered systems since secondary reflection waves generated at the interfaces significantly affected the peak stress and pressure profiles, influencing void nucleation and failure modes. In the trilayer systems, failure predominantly occurred at interfaces and within the Ta layer, with void nucleation sites and twinning behavior being markedly different compared to single-crystal Cu and Ta. Increasing the Ta layer thickness modified the wave interactions, leading to different failure locations. Higher piston velocities were associated with increased spall strength by enhancing wave interactions and void formation, particularly at the interfaces and within the Ta layer, under specific configurations. Additionally, shorter shock pulse durations facilitated earlier initiation of the release fan, reducing twin formation and altering the failure dynamics by accelerating twin annihilation and pressure release.

36 MATERIALS SCIENCE↗

Improving Performance of III-V Solar Cells Grown on Spalled Germanium with Ex Situ Substrate Planarization

Controlled spalling allows removal of devices and provides an opportunity for cost reduction through substrate reuse. However, the fracture-based process can leave behind morphological surface features, notably river lines, that can disrupt epitaxial growth and degrade device performance. We investigate the viability of various wet etch chemistries to planarize river lines to ensure high-quality device growth and performance without mechanical repolishing, and so maintain a route towards cost-effective reuse. Etching in a HF: HNO 3 :CH 3 COOH solution effectively planarizes river lines and produces a surface that yields devices with equivalent performance to those grown on epi-ready Ge wafer surfaces. Further studies will focus on optimizing etch composition, temperature, and time to minimize material removal while maintaining a suitable surface for high-quality epitaxy.

germanium↗