Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stack design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Three-dimensional photonic crystals by large-area membrane stacking

We designed and analyzed a “mesh-stack” three-dimensional photonic crystal of a 12.4% bandgap with a dielectric constant ratio of 12:1. The mesh-stack consists of four offset identical square-lattice air-hole patterned membranes in each vertical period that is equal to the in-plane period of the square lattice. This design is fully compatible with the membrane-stacking fabrication method, which is based on alignment and stacking of large-area single-crystal membranes containing engineered defects. A bandgap greater than 10% is preserved as long as the membranes are subjected to in-plane misalignment less than 3% of the square period. By introducing a linear defect with a nonsymmorphic symmetry into the mesh-stack, we achieved a single-mode waveguide over a wide bandwidth.

36 MATERIALS SCIENCE↗

Computerized method and system for designing an aerodynamic focusing lens stack

A computerized method and system for designing an aerodynamic focusing lens stack, using input from a designer related to, for example, particle size range to be considered, characteristics of the gas to be flowed through the system, the upstream temperature and pressure at the top of a first focusing lens, the flow rate through the aerodynamic focusing lens stack equivalent at atmosphere pressure; and a Stokes number range. Based on the design parameters, the method and system determines the total number of focusing lenses and their respective orifice diameters required to focus the particle size range to be considered, by first calculating for the orifice diameter of the first focusing lens in the Stokes formula, and then using that value to determine, in iterative fashion, intermediate flow values which are themselves used to determine the orifice diameters of each succeeding focusing lens in the stack design, with the results being output to a designer. In addition, the Reynolds numbers associated with each focusing lens as well as exit nozzle size may also be determined to enhance the stack design.

47 OTHER INSTRUMENTATION↗

Integrated Silicon Platform for Co-planar Design of Vertically Stacked 2.06 THz Mixer Module

The process for fabricating and utilizing the threedimensional Si stack receiver front-end is described in this paper. The capability to have exact dimensionality becomes essential as frequency scales due to the complexity arising in assembly and finer tolerances. Total process yields can be improved through Si fabrication by verifying achievement of specified tolerances lithographically and compatibility to rapid process changes and design fine-tuning. The integrated Si platform with the mounted device is shown in Figure 1. Signal I/O and alignment modalities enable lownoise measurements. Silicon micromachining provides the necessary accuracy for integration at the several THz regime. Particularly, processing and etch recipes have demonstrated smooth surfaces of < 1 μm surface roughness. In consideration is pre-compensating for minute offsets, matching mechanical strain on all interfaces, and including passive alignment verification in the design. As compared to metal blocks, computer numerical controlled (CNC) milling can produce slight burrs in the interfaces resulting in misalignment and resultant strain between two pieces of components. Furthermore, Si integration can make possible arrays of pixel transceivers through compact subsystems for the purpose of measuring multiple lines of spectral content simultaneously in space.

Mehdi, Imran↗

Multi-layer Printing of Complex Antennas Using Aerosol Jet Technology (CRADA NFE-18-07315 Final Report)

This project demonstrated the feasibility of producing multilayer radio-frequency (RF) and microwave-frequency components using aerosol jet additive manufacturing technology. Funded by the U.S. Department of energy, Advanced Manufacturing Office, this effort focused on novel stacked component designs for devices such as antennas, electronic filters, resistive/inductive/capacitive (RLC) components, and transmission lines. Our approach to RF/microwave component fabrication by aerosol jet printing has the potential to reduce component size, improve performance characteristics, and allow devices to be fabricated on non-planar surfaces. Specifically, folded micro-patch antenna designs were fabricated by stacking layers of conductors and dielectrics printed in sequence using Optomec’s aerosol jet technology. ORNL supported the effort by providing design input on printing parameters and characterizing the performance of printed structures. ORNL identified suitable stacked antenna designs, produced finite element models (FEM) in high-frequency simulation software (HFSS), and provided the designs to Optomec for printing. After printing, the devices were tested and characterized at ORNL to determine the frequency response and material characteristics of the printed components. These proof-of-principle devices will provide feedback on printing parameters, optimizations for the FEM models, and a path for more complex multilayer device designs.

42 ENGINEERING↗

Fuel cell technology program

A fuel cell technology program was established to advance the state-of-the-art of hydrogen-oxygen fuel cells using low temperature, potassium hydroxide electrolyte technology as the base. Program tasks are described consisting of baseline cell design and stack testing, hydrogen pump design and testing, and DM-2 powerplant testing and technology extension efforts. A baseline cell configuration capable of a minimum of 2000 hours of life was defined. A 6-cell prototype stack, incorporating most of the scheme cell features, was tested for a total of 10,497 hours. A 6-cell stack incorporating all of the design features was tested. The DM-2 powerplant with a 34 cell stack, an accessory section packaged in the basic configuration anticipated for the space shuttle powerplant and a powerplant control unit, was defined, assembled, and tested. Cells were used in the stack and a drag-type hydrogen pump was installed in the accessory section. A test program was established, in conjunction with NASA/JSC, based on space shuttle orbiter mission. A 2000-hour minimum endurance test and a 5000-hour goal were set and the test started on August 8, 1972. The 2000-hour milestone was completed on November 3, 1972. On 13 March 1973, at the end of the thirty-first simulated seven-day mission and 5072 load hours, the test was concluded, all goals having been met. At this time, the DM-2 was in excellent condition and capable of additional endurance.

Source record↗

Design principles for electronic charge transport in solution-processed vertically stacked 2D perovskite quantum wells

State-of-the-art quantum-well-based devices such as photovoltaics, photodetectors, and light-emission devices are enabled by understanding the nature and the exact mechanism of electronic charge transport. Ruddlesden–Popper phase halide perovskites are two-dimensional solution-processed quantum wells and have recently emerged as highly efficient semiconductors for solar cell approaching 14% in power conversion efficiency. However, further improvements will require an understanding of the charge transport mechanisms, which are currently unknown and further complicated by the presence of strongly bound excitons. Here, we unambiguously determine that dominant photocurrent collection is through electric field-assisted electron–hole pair separation and transport across the potential barriers. This is revealed by in-depth device characterization, coupled with comprehensive device modeling, which can self-consistently reproduce our experimental findings. These findings establish the fundamental guidelines for the molecular and device design for layered 2D perovskite-based photovoltaics and optoelectronic devices, and are relevant for other similar quantum-confined systems.

36 MATERIALS SCIENCE↗

Design and assembly considerations for Redox cells and stacks

Individual redox flow cells are arranged electrically in series and hydraulically in parallel to form a single assembly called a stack. The hardware currently being tested in the laboratory has an active electrode area of either 310 sq cm or 929 sq cm. Four 310 sq cm stacks, each consisting of 39 active cells, were incorporated into a 1.0 kW preprototype system. The physical design of the stack is very critical to the performance and efficiency of the redox storage sytem. This report will discuss the mechanical aspects of the cell and stack design for the current Redox hardware, with regard to sealing the stack internally as well as externally, minimizing shunt currents and minimizing the electrical resistance of the stack.

Stalnaker, D. K.↗

Nickel hydrogen bipolar battery electrode design

The preferred approach of the NASA development effort in nickel hydrogen battery design utilizes a bipolar plate stacking arrangement to obtain the required voltage-capacity configuration. In a bipolar stack, component designs must take into account not only the typical design considerations such as voltage, capacity and gas management, but also conductivity to the bipolar (i.e., intercell) plate. The nickel and hydrogen electrode development specifically relevant to bipolar cell operation is discussed. Nickel oxide electrodes, having variable type grids and in thicknesses up to .085 inch are being fabricated and characterized to provide a data base. A selection will be made based upon a system level tradeoff. Negative (hydrpogen) electrodes are being screened to select a high performance electrode which can function as a bipolar electrode. Present nickel hydrogen negative electrodes are not capable of conducting current through their cross-section. An electrode was tested which exhibits low charge and discharge polarization voltages and at the same time is conductive. Test data is presented.

Puglisi, V. J.↗

Modularization of Ceramic Hollow Fiber Membrane Technology for Air Separation

This proposed project is aimed at studying high performance and economically competitive ceramic membrane technology for air separation and high-purity oxygen production using hollow fiber ceramic membrane stack and module technology. The design of the single permeate membrane is a hollow fiber substrate-supported thin tri-layer structure. Radially well-aligned micro-channels are embedded in the thick substrate and open at the inner surface of the substrate, enabling facile air/gas diffusion. The tri-layer structure of thin dense membrane layer (~ 10 µm) sandwiched by porous surface layer on either side is then built on the substrate using advanced fabrication process. The tri-layer structure design allows different materials to be used in different layers, where the materials of surface layers have high surface exchange coefficients while the material of dense layer has high bulk diffusivity. Such a synergetic combination leads to high permeation performance. The focus of the proposed project will be on membrane stack/module development using the developed single hollow fiber membranes, including: 1) fabrication and characterization of novel single hollow fiber membranes; 2) membrane stack design and assembly using fabricated single membranes; 3) stack modeling and analysis to guide membrane stack designs; 4) permeation performance testing and characterization of membrane stacks. The hollow fiber feature and simple sealing requirement enable very compact design of membrane stacks, which have excellent flexibility for further modularizations at different scales. The operations of such membrane stack and module may employ the exhaust heat from other components of Integrated Gasification Combined Cycle and oxy-combustion systems. Therefore, modularization of such an air separation membrane technology can be incorporated into the DOE’s REMS (radically engineered modular systems)-gasification skid and support the oxidant feed of an oxygen-blown REMS gasifier scaled to different ranges.

01 COAL, LIGNITE, AND PEAT↗

Linear Transformer Drivers for Z-pinch Based Propulsion

The MSFC/UAH team has been developing of a novel power management and distribution system called a Linear Transformer Driver (LTD). LTD's hold the promise of dramatically reducing the required mass to drive a z-pinch by replacing the capacitor banks which constitute half the mass of the entire system. The MSFC?UAH tea, is developing this technology in hope of integrating it with the Pulsed Fission Fusion (PuFF) propulsion concept. High-Voltage pulsed power systems used for Z-Pinch experimentation have in the past largely been based on Marx Generators. Marx generators deliver the voltage and current required for the Z-Pinch, but suffer from two significant drawbacks when applied to a flight system: they are very massive, consisting of high-voltage capacitor banks insulated in oil-filled tanks and they do not lend themselves to rapid pulsing. The overall goal of Phase 2 is to demonstrate the construction of a higher voltage stack from a number of cavities each of the design proven in Phase 1 and to characterize and understand the techniques for designing the stack. The overall goal of Phase 3 is to demonstrate the feasibility of constructing a higher energy cavity from a number of smaller LTD stacks, to characterize and understand the way in which the constituent stacks combine, and to extend this demonstration LTD to serve as the basis for a 64 kJ pulse generator for Z-Pinch experiments.

Adams, Robert↗