Search NASA⌕ Search

SEARCH · Search NASA

Results for “Storage Capabilities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

A combined experimental and machine learning exploration of Ti 2-x Zr x MnCrFeNi high entropy Laves hydrides

A series of high entropy AB 2 -type Ti 2-x Zr x MnCrFeNi alloys (x = 0.6, 0.7, 0.8, 0.9, 1.0, 1.1 and 1.2) were synthesized to investigate their potential for hydrogen storage and chemical compression. The influence of the Ti/Zr ratio was explored in terms of structural, microstructural and thermodynamic properties. The storage capacity together with the reaction enthalpy and entropy changes of the synthesized high entropy alloys were compared to predictions from Machine Learning (ML) to investigate changes in these properties across the explored composition space. The results revealed that a decreasing Zr content consistently lowered the hydride formation enthalpy and increased the plateau pressure from 8 to >90 bar H 2 at 25 °C, in good agreement with ML predictions. Selected compositions (x = 1.0 and 1.2) demonstrated reversible hydrogen storage capability over 150 cycles, with capacities of 1.34–1.40 wt % H 2 and remarkable reaction kinetics (<4 min) at ambient temperature. These experimental and computational findings highlight the potential of this Laves-HEA system as tuneable, stable, and cost-effective materials suitable for long-term operations in stationary hydrogen storage and compression applications.

36 MATERIALS SCIENCE↗

Pouch cells with 15% silicon calendar-aged for 4 years

Small amounts of high-capacity silicon-based materials are already used in the anode of commercial Li-ion batteries, helping increase their energy density. Despite their remarkable storage capability, silicon continu-ously reacts with the electrolyte, accelerating time-dependent cell performance fade. Nevertheless, very limited information is available on the specific consequences of this reactivity for the calendar aging of Li-ion cells. Here, we analyze aging effects on 450 mAh pouch cells containing 15 wt% of Si (and 73 wt% graphite) after storage at 21 °C for four years. We show that severe losses of Si capacity occurred due to particle isolation when cells were stored at high states of charge (SOC), but not when cells were fully discharged prior to storage. Impedance rise was also significantly higher when cells were kept at high SOCs and was mostly due to phenomena taking place at the cathode; the continuous electrolyte reduction at the anode did not lead to a major increase in bulk electrode resistance. A series of post-test characterization provided additional information on the effects of time and SOC on the calendar aging of Si-containing cells. In conclusion, our study highlights the many challenges posed by Si during calendar aging and can inform future studies in the field.

25 ENERGY STORAGE↗

KVOPO 4 : A New High Capacity Multielectron Na-Ion Battery Cathode

Sodium ion batteries have attracted much attention in recent years, due to the higher abundance and lower cost of sodium, as an alternative to lithium ion batteries. However, a major challenge is their lower energy density. In this work, we report a novel multi–electron cathode material, KVOPO4, for sodium ion batteries. Due to the unique polyhedral framework, the V 3+ ↔ V 4+ ↔ V 5+ redox couple was for the first time fully activated by sodium ions in a vanadyl phosphate phase. The KVOPO 4 based cathode delivered reversible multiple sodium (i.e. maximum 1.66 Na + per formula unit) storage capability, which leads to a high specific capacity of 235 Ah kg –1 . Combining an average voltage of 2.56 V vs. Na/Na+, a high practical energy density of over 600 Wh kg –1 was achieved, the highest yet reported for any sodium cathode material. The cathode exhibits a very small volume change upon cycling (1.4% for 0.64 sodium and 8.0% for 1.66 sodium ions). In conclusion, density functional theory (DFT) calculations indicate that the KVOPO4 framework is a 3D ionic conductor with a reasonably, low Na + migration energy barrier of ≈450 meV, in line with the good rate capability obtained.

25 ENERGY STORAGE↗

Fabrication and characterization of ferroelectric PLZT film capacitors on metallic substrates.

We have grown ferroelectric Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) films on Hastelloy C276 (HC) substrates by chemical solution deposition. Samples of 1.15-{micro}m-thick PLZT films were prepared on HC with and without lanthanum nickel oxide (LNO) films as an intermediate buffer layer. On samples with and without LNO buffers at room temperature, we measured dielectric constants of {approx}1,300 and {approx}450 and loss tangents of {approx}0.06 and {approx}0.07, respectively. For PLZT films grown on HC with LNO buffer, the dielectric constant increases, while the dielectric loss decreases, with increasing temperature. A dielectric constant of {approx}2,000 and loss of {approx}0.05 were observed at 150 C. Samples with LNO buffer also exhibited slimmer hysteresis loops and lower leakage current density when compared to samples without LNO buffer. The following results were measured on samples with and without LNO buffers: remanent polarization (P{sub r}) values of 21.3 and 36.4 {micro}C/cm{sup 2}, coercive electric field (E{sub c}) values of 41 and 173 kV/cm, and leakage current densities of {approx}1.1 x 10{sup -8} and {approx}1.6 x 10{sup -7} A/cm{sup 2}, respectively. The energy storage capability was measured at {approx}65 J/cm{sup 3} for the PLZT film-on-foil capacitor deposited on HC with LNO buffer.

36 MATERIALS SCIENCE↗

Chemical solution deposition of ferroelectric lead lanthanum zirconate titanate films on base-metal foils.

Development of electronic devices with better performance and smaller size requires the passive components to be embedded within a printed wire board (PWB). The 'film-on-foil' approach is the most viable method for embedding these components within a PWB. We have deposited high-permittivity ferroelectric lead lanthanum zirconate titanate (Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub x}, PLZT 8/52/48) films on base metal foils by chemical solution deposition. These prefabricated capacitor sheets can be embedded into PWBs for power electronic applications. To eliminate the parasitic effect caused by the formation of a low-permittivity interfacial oxide, a conductive buffer layer of lanthanum nickel oxide (LNO) was applied by chemical solution deposition on nickel foil before the deposition of PLZT. With a {approx} 0.7-{micro}m-thick ferroelectric PLZT film grown on LNO-buffered nickel foil, we measured capacitance densities of 1.5 {micro}F/cm{sup 2}, breakdown field strength E{sub b} > 1.2 MV/cm, and leakage current density of 2 x 10{sup -8}A/cm{sup 2}. The dielectric relaxation current decay obeys the Curie-von Schweidler law, with exponent n = 0.85 and 0.94 for PLZT grown directly on Ni and that grown on LNO-buffered Ni foils, respectively. When compared with samples deposited directly on Ni substrate, PLZT grown on LNO buffered Ni substrates exhibit slimmer hysteresis loop and better energy storage capability. With these desirable characters, PLZT film-on-foil capacitors hold particular promise for use in high-voltage embedded passives.

36 MATERIALS SCIENCE↗

Performance Analysis of Li-ion Battery Under Various Thermal and Load Conditions

In the recent years, with the rapid advancements made in the technologies of electric and hybrid electric vehicles, selecting suitable batteries has become a major factor. Among the batteries currently used for these types of vehicles, the lithium-ion battery leads the race. Apart from that, the energy gained from regenerative braking in locomotives and vehicles can be stored in batteries for later use for propulsion thus improving the fuel consumption and efficiency. But batteries can be subjected to a wide range of temperatures depending upon the operating conditions. Thus, a thorough knowledge of the battery performance over a wide range of temperatures and different load conditions is necessary for their successful employment in future technologies. In this context, this study aims to experimentally analyze the performance of Li-ion batteries by monitoring the charge–discharge rates, efficiencies, and energy storage capabilities under different environmental and load conditions. Sensors and thermal imaging camera were used to track the environment and battery temperatures, whereas the charge–discharge characteristics were analyzed using CADEX analyzer. The results show that the battery performance is inversely proportional to charge–discharge rates. This is because, at higher charge–discharge rates, the polarization losses increase thus increasing internal heat generation and battery temperature. Also, based on the efficiency and energy storage ability, the optimum performing conditions of the Li-ion battery are 30–40 °C (temperature) and 0.5 C (C-rate).

25 ENERGY STORAGE↗

Evaluation of bio-inspired flow fields in a mediated Li-S flow battery for grid energy storage

Lithium-sulfur is a redox flow battery with high energy density for applications in safe, reliable, and lasting scaling of energy. However, lithium-based batteries often encounter platting as a problem thanks to poor Li-ions deposition after cycling. Aiming to reduce this impact, a uniform and continuous flow of ions is needed. On this work, novel bio-inspired flow fields in the electrochemical cell were tested to improve ions flowability and lithium platting control, ultimately enhancing battery performance and life. To secure Li-S efficient, low-cost, and secure energy storage capabilities, we chose a configuration with decamethylferrocene and cobaltocene acting as redox mediators, Li metal as anode and sulfur kept in a separate catholyte reservoir. Flow test and battery results insinuated a beneficial influence of bio-inspired designs in flowing electrolyte uniformly with less pressure and pump power in comparison to other conventional designs used in the industry, with an encouraging ability to approach a cheap, safe, and reliable Li-S grid energy storage.

25 ENERGY STORAGE↗

Internal Insulation and Corrosion Control of Molten Chloride Storage Tanks

The National Renewable Energy Laboratory (NREL) is leading a multi-national team to validate the potential of a chloride-based molten-salt system that uses a ternary blend of MgCl2/KCl/NaCl to provide higher temperature thermal energy storage capability, thereby allowing for higher efficiency in the power block of next-generation concentrating solar power systems. While higher thermal stability, greater operating temperature, and a more efficient power cycle are possible, the molten chlorides present several unique challenges, including the design of internal liners to prevent the corrosion and thermal stress of alloy tank shells. This work discusses issues and potential solutions related to containment of molten chloride salt, specifically the design of the molten salt storage tanks.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Hexagonal boron nitride nanoparticles decorated halloysite clay nanotubes as a potential hydrogen storage medium

The light weight and compact hydrogen storage materials is still prerequisite for the carbon free hydrogen fuel cell technology. In this work, the hydrogen storage performance of acid treated halloysite clay nanotubes (A-HNTs) and hexagonal boron nitride (h-BN) nanoparticles decorated acid treated halloysite nanoclay composite (A-HNT-h-BN) are demonstrated, where facile ultrasonic technique is adopted for the synthesis of A-HNT-h-BN nanoclay composite. Hydrogen storage studies were carried out using Sieverts-like hydrogenation setup. The A-HNTs and A-HNT-h-BN nanoclay composite were analyzed by XRD, FTIR, HRTEM, EDX, CHNS-elemental analysis and TGA. The A-HNT-h-BN nanoclay composite shows superior storage capacity of 2.19 wt% at 50 °C compared to the A-HNTs (0.58 wt%). A 100% desorption of stored hydrogen is noted in the temperature range of 138–175 °C. The average binding energy of hydrogen was found to be 0.34 eV for the prepared A-HNT-h-BN nanoclay composite. The excellent storage capability of A-HNT-h-BN nanoclay composite towards hydrogen at ambient temperature may find bright perspective in hydrogen fuel cell technology in near future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Lithium doping on covalent organic framework-320 for enhancing hydrogen storage at ambient temperature

Density Functional Theory (DFT) combines with grand canonical Monte Carlo (GCMC) simulations are performed to explore the effect of Li doping on the hydrogen storage capability of COF-320. The results show that the interaction energy between the H{sub 2} and the Li-doped COF-320 is about three times higher than that of pristine COF-320. GCMC simulations are employed to study the hydrogen uptake of Li-doped COF-320 at ambient temperature, further confirm that the lithium doping can improve the hydrogen uptake at ambient temperature. Our results demonstrate that Li-doped COFs have good potential in the field of hydrogen storage. - Graphical abstract: Fig. 1. The optimized cluster model used here to represent the COF-320 and possible adsorption sites (A, B, C) for adsorption of metals in the COF-320. The dangling bonds are terminated by H atoms. C, H, and N atoms are shown as gray, white, and blue colors, respectively. Fig. 2. The adsorption isotherm of H{sub 2} in the pristine and Li-doped COF-320 at 298 K. - Highlights: • The binding sites of single and two lithium atoms in COF-320 were studied. • The interaction energy between the H{sub 2} and the Li-doped COF-320 is about three times higher than that of pristine COF-320. • H{sub 2} uptakes on the Li-doped COFs obtain significant improvement at ambient temperature. • Lithium-doping is a successful strategy for improving hydrogen uptake.

36 MATERIALS SCIENCE↗

Plug-in hybrid electric vehicles : How does one determine their potential for reducing U.S. oil dependence?

Estimation of the potential of plug-in hybrid electric vehicles (PHEV's) ability to reduce U.S. gasoline use is difficult and complex. Although techniques have been proposed to estimate the vehicle kilometers of travel (VKT) that can be electrified, these methods may be inadequate and/or inappropriate for early market introduction circumstances. Factors that must be considered with respect to the PHEV itself include (1) kWh battery storage capability; (2) kWh/km depletion rate of the vehicle (3) liters/km use of gasoline (4) average daily kilometers driven (5) annual share of trips exceeding the battery depletion distance (6) driving cycle(s) (7) charger location [i.e. on-board or off-board] (8) charging rate. Each of these factors is actually a variable, and many interact. Off the vehicle, considerations include (a) primary overnight charging spot [garage, carport, parking garage or lot, on street], (b) availability of primary and secondary charging locations [i.e. dwellings, workplaces, stores, etc] (c) time of day electric rates (d) seasonal electric rates (e) types of streets and highways typically traversed during most probable trips depleting battery charge [i.e. city, suburban, rural and high vs. low density]; (f) cumulative trips per day from charger origin (g) top speeds and peak acceleration rates required to make usual trips. Taking into account PHEV design trade-off possibilities (kW vs. kWh of battery, in particular), this paper attempts to extract useful information relating to these topics from the 2001 National Household Travel Survey (NHTS), and the 2005 American Housing Survey (AHS). Costs per kWh of PHEVs capable of charge depleting (CD) all-electric range (CDE, or AER) vs. those CD in 'blended' mode (CDB) are examined. Lifetime fuel savings of alternative PHEV operating/utilization strategies are compared to battery cost estimates.

02 PETROLEUM↗

Rational Design of Statically and Dynamically Stable Lithium-Sulfur Batteries with High Sulfur Loading and Low Electrolyte/Sulfur Ratio

Here, the primary challenge with lithium–sulfur battery research is the design of sulfur cathodes that exhibit high electrochemical efficiency and stability while keeping the sulfur content and loading high and the electrolyte/sulfur ratio low. With a systematic investigation, a novel graphene/cotton–carbon cathode is presented here that enables sulfur loading and content as high as 46 mg cm –2 and 70 wt% with an electrolyte/sulfur ratio of as low as only 5. The graphene/cotton–carbon cathodes deliver peak capacities of 926 and 765 mA h g –1 , respectively, at C/10 and C/5 rates, which translate into high areal, gravimetric, and volumetric capacities of, respectively, 43 and 35 mA h cm –2 , 648 and 536 mA h g –1 , and 1067 and 881 mA h cm –3 with a stable cyclability. They also exhibit superior cell–storage capability with 95% capacity–retention, a low self–discharge constant of just 0.0012 per day, and stable poststorage cyclability after storing over a long period of six months. Here, this work demonstrates a viable approach to develop lithium–sulfur batteries with practical energy densities exceeding that of lithium–ion batteries.

25 ENERGY STORAGE↗

Spent nuclear fuel receipt rate analysis within an integrated waste management system (IWMS) architecture that includes consolidated storage

A key parameter in analyzing the performance of an integrated waste management system (IWMS) architecture for the disposition of spent nuclear fuel (SNF) is the SNF receipt rate from reactor and other custodian sites. Receipt rate in this paper means how much SNF is accepted per year for transport in the IWMS from such sites. Introducing one or more federal consolidated interim storage facilities (CISFs) into the IWMS architecture can potentially accelerate the receipt rate profile over time relative to system architectures without a CISF. This raises the question of what an optimal SNF receipt rate profile for an IWMS architecture might be in view of practical constraints and desired system performance attributes and associated metrics. This paper describes a sensitivity study on SNF receipt rates and the associated results for a selected set of IWMS scenarios aimed at informing near-term planning for interim storage capabilities and transportation assets. Two different strategies for CISF operation while awaiting availability of a disposal system to receive SNF are compared: one that relatively quickly fills an initial CISF and then idles the transportation system; and another that aims for more continuous use of transportation assets and receipt capabilities at the CISF. This study examines cost considerations and other factors, such as the timing of clearing reactor sites of SNF, efficient use of capital assets, and some other metrics that might be important to a CISF host community. Based on the analysis, an initial approach is presented that targets a continuous receipt strategy while maintaining the flexibility to step up receipt capabilities to a reasonable degree when needed and beneficial, within overall system constraints.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advancements in the modification of TiFe alloys for enhanced hydrogen Storage: Strategies and future Directions

Hydrogen is considered a promising clean energy source, and a potential alternative to conventional fossil fuels. TiFe alloy has been particularly interesting due to its ability to reversibly absorb and desorb hydrogen at room temperature and low pressure. The initial hydrogen absorption stage of TiFe alloy requires activation under high-temperature and high-pressure conditions, which hinders its practical application. Here, this paper primarily examines the impact of elemental substitution methods on the hydrogen storage capabilities of TiFe alloys, with a particular emphasis on elucidating the mechanisms associated with various substituent elements. Commonly utilized elements, such as Mn, V, and Zr, significantly improve the activation performance of TiFe alloys. Additionally, the incorporation of elements such as Ni, Cr, Ce, and Y contributes to the modulation of phase composition, as well as the enhancement of activation and kinetic properties. However, there exists a notable deficiency in systematic investigations concerning alternative elements, coupled with a frequent oversight of the preparation process's influence on the hydrogen storage characteristics of these alloys. Consequently, the mechanisms by which different elements affect the hydrogen storage process in TiFe alloys remain inadequately understood among current research, thereby complicating the establishment of experiment-based design guidelines for TiFe alloys. Furthermore, the plasma treatment and high-entropy alloying present new approaches for optimizing the hydrogen storage properties of TiFe alloys. This paper aims to present novel research perspectives and insights to scholars in the field by introducing methods for the modification of TiFe alloys.

Hydrogen storage↗

Spent Nuclear Fuel Receipt Rate Analysis within an Integrated Waste Manage-ment System Architecture that Includes Consolidated Interim Storage

A key parameter in analyzing the performance of an integrated waste management system (IWMS) architecture for the disposition of spent nuclear fuel (SNF) is the SNF receipt rate from reactor and other custodian sites. The introduction of one or more federal consolidated interim storage facilities (CISFs) into the IWMS architecture can enable the receipt rate profile as a function of time to be accelerated relative to system architectures without a CISF. The question then arises as to what an optimal SNF receipt rate profile for an IWMS architecture might be in view of practical constraints and desired system performance attributes and associated metrics. This paper describes a sensitivity study on SNF receipt rates and the associated results for a selected set of IWMS scenarios aimed an in-forming near-term planning for interim storage capabilities and transportation assets. Two different strategies are compared, one that fills an initial CISF quickly and then idles the transportation system while a disposal system is prepared, and a second strategy that aims to provide a more continuous use of transportation assets and receipt capabilities at the IWMS while the disposal system is readied for SNF receipt. Cost considerations and other factors such as impact on timing of clearing reactor sites of SNF, efficient use of capital assets, and other metrics, including those which may be important to a CISF host community, are examined. Based on the analysis, an initial approach is presented targeting a continuous receipt strategy while having the flexibility to step up receipt capabilities to a reasonable degree when needed and beneficial within overall system constraints.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An Assessment of Deploying Advanced Pumped Storage Hydropower Technology in U.S. Electricity Markets

Pumped storage hydropower (PSH) is a type of hydropower technology where energy can be stored and generated by moving water between two reservoirs of differing elevations. In addition to providing 97% of the total utility-scale hydropower storage in the United States, PSH plants have operational characteristics - such as high ramp rates and the ability to provide reserves - that contribute to greater flexibility and reliability of the power grid. New PSH technologies can provide additional flexibility beyond existing, fixed-speed units. With the emergence of high levels of variable renewable energy resources (e.g., wind and solar), energy storage is expected to be crucial to the reliability and reliance of the power grid in a low-carbon future. At diurnal and longer durations, PSH plants have some of the lowest costs per unit of energy, have been proven to be reliable and efficient, are not cycle-limited, and typically have long lives, often exceeding 50 years. The work presented here focuses on a new generation of PSH: ternary PSH and quaternary PSH (together referred to as T/Q-PSH). Given recent experience in Europe, grid operators in the United States and elsewhere are increasingly focusing their attention on T/Q-PSH as a proven, financeable technology that can offer utility-scale, long-duration, fast-acting energy storage capabilities and grid services. T/Q-PSH differs from conventional PSH in that it can provide fast-response ancillary services during both generating and pumping operations. This capability together with fast mode switching times are key attributes that make T/Q-PSH technologies attractive for managing and stabilizing electricity systems with high amounts of variable renewable energy.

ENERGY PLANNING, POLICY, AND ECONOMY,HYDRO ENERGY↗

Opportunities for Automated Demand Response in Wastewater Treatment Facilities in California - Southeast Water Pollution Control Plant Case Study

This report details a study into the demand response potential of a large wastewater treatment facility in San Francisco. Previous research had identified wastewater treatment facilities as good candidates for demand response and automated demand response, and this study was conducted to investigate facility attributes that are conducive to demand response or which hinder its implementation. One years' worth of operational data were collected from the facility's control system, submetered process equipment, utility electricity demand records, and governmental weather stations. These data were analyzed to determine factors which affected facility power demand and demand response capabilities The average baseline demand at the Southeast facility was approximately 4 MW. During the rainy season (October-March) the facility treated 40% more wastewater than the dry season, but demand only increased by 4%. Submetering of the facility's lift pumps and centrifuges predicted load shifts capabilities of 154 kW and 86 kW, respectively, with large lift pump shifts in the rainy season. Analysis of demand data during maintenance events confirmed the magnitude of these possible load shifts, and indicated other areas of the facility with demand response potential. Load sheds were seen to be possible by shutting down a portion of the facility's aeration trains (average shed of 132 kW). Load shifts were seen to be possible by shifting operation of centrifuges, the gravity belt thickener, lift pumps, and external pump stations These load shifts were made possible by the storage capabilities of the facility and of the city's sewer system. Large load reductions (an average of 2,065 kW) were seen from operating the cogeneration unit, but normal practice is continuous operation, precluding its use for demand response. The study also identified potential demand response opportunities that warrant further study: modulating variable-demand aeration loads, shifting operation of sludge-processing equipment besides centrifuges, and utilizing schedulable self-generation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗