Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Preloaded Composite-Strut/End-Fitting Joint

Proposed structural joint between composite strut and metal end fitting strong and light in weight. Joint configured to distribute stresses fairly uniformly, with little interlaminar stress. Composite-strut/metal-fitting joint built up integrally with strut in layup process. Joint remains tight under reversals of loads and changes in temperature.

Monitor, Dean S.↗

Analysis and testing of axial compression in imperfect slender truss struts

The axial compression of imperfect slender struts for large space structures is addressed. The load-shortening behavior of struts with initially imperfect shapes and eccentric compressive end loading is analyzed using linear beam-column theory and results are compared with geometrically nonlinear solutions to determine the applicability of linear analysis. A set of developmental aluminum clad graphite/epoxy struts sized for application to the Space Station Freedom truss are measured to determine their initial imperfection magnitude, load eccentricity, and cross sectional area and moment of inertia. Load-shortening curves are determined from axial compression tests of these specimens and are correlated with theoretical curves generated using linear analysis.

Lake, Mark S.↗

Strut-node joint conjugates for the assembly of semi-permanent or reusable truss structures

When strut and node components are used for truss construction an assembly problem occurs if a strut must be fitted between nodes whose separation distance is either closer or farther than the design intended. This condition is the result of normal dimensional variations that occur in any manufacturing process. In such circumstances two actions would permit continued assembly: change the effective strut length, and move the nodes. Assuming continued assembly is the most attractive alternative, attention is focused on accomplishing these actions as part of the assembly process.

Brewer, W. V.↗

Composite Struts Would Damp Vibrations

New design of composite-material (fiber/matrix laminate) struts increases damping of longitudinal vibrations without decreasing longitudinal stiffness or increasing weight significantly. Plies with opposing chevron patterns of fibers convert longitudinal vibrational stresses into shear stresses in intermediate viscoelastic layer, which dissipate vibrational energy. Composite strut stronger than aluminum strut of same weight and stiffness.

Dolgin, Benjamin P.↗

Simulation of the Space Station strut-out condition

A method is presented for reanalyzing a truss structure when one of the truss elements (struts) has failed. The method uses a modal model of the nominal structure coupled with a residual flexibility term to predict the effect of the failed strut without resolving the finite element model. By implementing the method as part of the transient simulation, it is feasible to consider a large number of potential strut failures with a minimum amount of extra effort. Preliminary application of the method to the Space Station indicates excellent agreement with results based on modifying and resolving the finite element model.

Blelloch, Paul A.↗

Impact damage in small diameter graphite/epoxy composite struts

An investigation was performed to study impact induced damage in small-diameter struts made of a composite material with a brittle matrix system. The major focus is on characterizing the impact behavior associated with the barely visible damage. An experimental procedure including ultrasonic inspection, instrumented impact testing, and delamination buckling and residual strength measurements is presented. From the ultrasonic inspection, it is found that for the strut specimens under investigation, the impact energy level for barely visible damage threshold is above that of the internal damage threshold. A 60- to 65-percent reduction in compressive strength was typical for struts subjected to the barely visible impact damage threshold.

Chen, G.-S.↗

Sizing of active piezoelectric struts for vibration suppression on a space-based interferometer

The present paper concerns itself with the active suppression of mechanical vibrations on a representative future spaceborne optical interferometer. This is accomplished by the incorporation of a set of piezoelectric struts into the truss structure of the interferometer and the use of these active struts to modify the damping and stiffness characteristics of the truss. It is shown that vibration propagation can be significantly reduced through the use of very simple control laws. It is further shown that the force and stroke requirements for the active struts for this application are rather modest and fall well within the capabilities already demonstrated by prototype hardware in ground testing.

Sirlin, S. W.↗

The Effect of the Nature of Surfaces on Resistance as Tested on Struts

The chief concern was to measure the variations of resistance brought about by the nature of the surface of the struts. The struts were spanned with aviation linen, and then covered with one coat of varnish. The top surface was not perfectly smooth after this treatment, being slightly rough owing to the threads and raised fibers of the fabric. The results of the measurements of the surfaces are shown by the dotted lines of the curves plotted in several figures. The resistance is given in terms of the characteristic value. Next, the surface was altered by the removal of any roughness on it by means of filing with sandpaper. The measurements of surfaces thus treated gave values represented by extended lines. The increase of resistance with increasing characteristic value, more or less marked in the first series of measurements, was no longer observable. Resistance always decreases with the increase of characteristic value, excepting in the case of strut 7, which shows a slight tendency to rise again. The reasons for this phenomenon have not yet been fully explained.

Wieselsberger, Ing C↗

Point drag and total drag of navy struts no. 1 modified

This report deals with the results of tests on struts conducted at Washington Navy Yard. Two models of the modified Navy strut, no. 1, were tested in the 8 by 8 foot wind tunnel. The tests were made to determine the total resistance end effect and the pressure distribution at various wind-tunnel speeds with the length of the strut transverse to the current. Only the measurements made at zero pitch and yaw are given in this report.

Zahm, A F↗

Strut and wall interference on jet-induced ground effects of a STOVL aircraft in hover

A small scale ground effect test rig was used to study the ground plane flow field generated by a STOVL aircraft in hover. The objective of the research was to support NASA-Ames Research Center planning for the Large Scale Powered Model (LSPM) test for the ARPA-sponsored ASTOVL program. Specifically, small scale oil flow visualization studies were conducted to make a relative assessment of the aerodynamic interference of a proposed strut configuration and a wall configuration on the ground plane stagnation line. A simplified flat plate model representative of a generic jet-powered STOVL aircraft was used to simulate the LSPM. Cold air jets were used to simulate both the lift fan and the twin rear engines. Nozzle Pressure Ratios were used that closely represented those used on the LSPM tests. The flow visualization data clearly identified a shift in the stagnation line location for both the strut and the wall configuration. Considering the experimental uncertainty, it was concluded that either the strut configuration o r the wall configuration caused only a minor aerodynamic interference.

Kristy, Michael H.↗

Improved Hypersonic Inlet Performance Using Validated Strut Compression Designs

Aerojet is currently executing two Strutjet propulsion contracts: one a Rocket Based Combined Cycle (RBCC) engine for a NASA-Marshall Space Flight Center (MSFC) Advanced Reusable Transportation Technology (ARTT) program, the second a Dual Mode Ram/Scramjet engine for a USAF Wright Laboratories Storable Fuel Scramjet Flow Path Concepts program. The engines employed in both programs operate at supersonic and low hypersonic speeds and use inlets employing forebody external and sidewall compression. Aerojet has developed and validated a successful design methodology applicable to these inlet types. Design features include an integrated vehicle forebody, external side compression struts, strut sidewall and throat bleed, a throat shock trap, and variable geometry internal contraction. Computation Fluid Dynamic (CFD) predictions and test data show these inlets allow substantially increased flow turning angles over other designs. These increased flow turning angles allow shorter and lighter engines than current designs, which in turn enables higher performing vehicles with broad operating characteristics. This paper describes the designs of two different inlets evaluated by the NASA-MSFC and USAF programs, discusses the results of wind tunnel tests performed by NASA-Lewis Research Center, and provides correlations of test data with CFD predictions. Parameters of interest include low Mach number starting capability, start sensitivity as a function of back pressure at various contraction ratios, flow turning angles, strut and throat bleed effects, and pressure recovery at various Mach numbers.

Bulman, M. J.↗

Aft Body Closure: Predicted Strut Effects at M=2.4

This paper reports the predicted M = 2.4 strut-interference effects on a closed aftbody with empennage for the TCA baseline model. The strut mounting technique was needed in order to assess the impact of aft-end shaping, i.e. open for a sting or closed to better represent a flight vehicle. However,this technique can potentially lead to unanticipated effects that are measured on the aft body. Therefore, a set of computations were performed in order to examine the closed aft body with and without strut present, at both zero and non-zero angles of sideslip (AOS). The work was divided into a computational task performed by Javier A. Garriz, using an inviscid (Euler) solver, and a monitoring/reporting task done by John E. Lamar. All this work was performed during FY98 at the NASA Langley Research Center.

Lamar, John E.↗

Evaluation of Long Composite Struts

Carbon-epoxy tapered struts are structurally efficient and offer opportunities for weight savings on aircraft and spacecraft structures. Seven composite struts were designed, fabricated and experimentally evaluated through uniaxial loading. The design requirements, analytical predictions and experimental results are presented. Struts with a tapered composite body and corrugated titanium end fittings successfully supported their design ultimate loads with no evidence of failure.

Jegley, Dawn C.↗

Highly Loaded Composite Strut Test Development

Highly loaded composite struts, representative of structural elements of a proposed truss-based lunar lander descent stage concept, were selected for design, development, fabrication and testing under NASA s Advanced Composites Technology program. The focus of this paper is the development of a capability for experimental evaluation of the structural performance of these struts. Strut lengths range from 60 to over 120 inches, and compressive launch and ascent loads can exceed -100,000 lbs, or approximately two times the corresponding tensile loads. Allowing all possible compressive structural responses, including elastic buckling, were primary considerations for designing the test hardware.

Wu, K. Chauncey↗

Development Testing and Subsequent Failure Investigation of a Spring Strut Mechanism

The NASA Engineering and Safety Center (NESC) and Lockheed Martin (LM) performed random vibration testing on a single spring strut development unit to assess its ability to withstand qualification level random vibration environments. Failure of the strut while exposed to random vibration resulted in a follow-on failure investigation, design changes, and additional development tests. This paper focuses on the results of the failure investigations referenced in detail in the NESC final report including identified lessons learned to aid in future design iterations of the spring strut and to help other mechanism developers avoid similar pitfalls.

Dervan, Jared↗

Development Testing and Subsequent Failure Investigation of a Spring Strut Mechanism

The NASA Engineering and Safety Center (NESC) and Lockheed Martin (LM) performed random vibration testing on a single spring strut development unit to assess its ability to withstand qualification level random vibration environments. Failure of the strut while exposed to random vibration resulted in a follow-on failure investigation, design changes, and additional development tests. This paper focuses on the results of the failure investigations referenced in detail in the NESC final report [1] including identified lessons learned to aid in future design iterations of the spring strut and to help other mechanism developers avoid similar pitfalls.

Dervan, Jared↗

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. In particular, designs were considered for fabrication at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC). The designs presented in this paper do not represent the exact geometry and material systems currently in use by the Artemis landing system, but they are considered to be representative. The designs produced during this study will be used to develop manufacturing demonstration units (MDU) that can be fabricated at ISAAC and tested in lab facilities at LaRC

carbon-epoxy↗

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. Rapid optimization trade studies were performed using low fidelity two-dimensional (2D) axisymmetric models with smeared composite properties. The optimum 2D model was compared with three-dimensional (3D) models with higher levels of fidelity in material property representation. Good agreement was found with all models. The buckling performance of the highest fidelity 3D model was found to be satisfactory for the intended loading conditions. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. The designs produced during this study are intended to be used to develop manufacturing demonstration units (MDU) that can be fabricated at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC) and tested in lab facilities at LaRC.

carbon-epoxy↗