Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface tension”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Surface-tension-induced convection experiment MA-041

In the absence of gravity, stirring in a liquid is suppressed because of density differences caused by thermal or compositional gradients. However, other mechanisms resulting in natural convection in a microgravity environment exist. One of the most important mechanisms for liquid metals is surface tension driven convection, which becomes predominant in the low gravity environment. In this case, surface tension differences caused by compositional or temperature gradients have been demonstrated to cause stirring in liquids during experiments performed onboard Skylab. Compositional gradients were created by adding a soap solution to a large water globule, which caused vigorous fluid motion for some moments after the addition.

Reed, R. E.↗
NASA NTRS1984

The effect of anisotropic crystal-melt surface tension on grain boundary groove morphology

The shape of a stationary solid-liquid interface in a temperature gradient near a grain boundary in a pure material is calculated for anisotropic crystal-melt surface tension and equal thermal conductivities of crystal and melt. Results are compared with those for the well-known problem of the two-dimensional equilibrium shape of a crystal. For small anisotropy, the resulting interface shapes have continuously turning tangents but differ in detail from the grain boundary groove shapes that have been calculated for isotropic surface tension. For larger anisotropy, the interface shapes have discontinuities in slope as a result of missing orientations.

Voorhees, P. W.↗
NASA NTRS1988

Fluoride glass: Crystallization, surface tension

Fluoride glass was levitated acoustically in the ACES apparatus on STS-11, and the recovered sample had a different microstructure from samples cooled in a container. Further experiments on levitated samples of fluoride glass are proposed. These include nucleation, crystallization, melting observations, measurement of surface tension of molten glass, and observation of bubbles in the glass. Ground experiments are required on sample preparation, outgassing, and surface reactions. The results should help in the development and evaluation of containerless processing, especially of glass, in the development of a contaminent-free method of measuring surface tensions of melts, in extending knowledge of gas and bubble behavior in fluoride glasses, and in increasing insight into the processing and properties of fluoride glasses.

Doremus, R. H.↗
NASA NTRS1988

Effect of surface tension anisotropy on cellular morphologies

A three-dimensional weakly nonlinear analysis for conditions near the onset of instability at the crystal-melt interface was carried out to second order, taking into account the effects of latent heat generation and surface-tension anisotropy of the crystal-melt interface; particular consideration was given to the growth of a cubic crystal in the 001-, 011-, and 111-line directions. Numerical calculations by McFadden et al. (1987), performed for an aluminum-chromium alloy with the assumption of a linear temperature field and an isotropic surface tension, showed that only hexagonal nodes (and not hexagonal cells) occurred near the onset of instability. The results of the present analysis indicate that the nonlinear temperature field (which occurs when thermal conductivities of the crystal and the melt are different and/or the latent heat effects are not negligible) can modify this result and, for certain alloys and processing conditions, can cause the occurrence of hexagonal cells near the onset of instability.

Mcfadden, G. B.↗
NASA NTRS1994

Surface Tension Driven Convection Experiment (STDCE)

Results are reported of the Surface Tension Driven Convection Experiment (STDCE) aboard the USML-1 (first United States Microgravity Laboratory) Spacelab which was launched on June 25, 1992. In the experiment 10 cSt silicone oil was placed in an open circular container which was 10 cm wide by 5 cm deep. The fluid was heated either by a cylindrical heater (1.11 cm dia.) located along the container centerline or by a CO2 laser beam to induce thermocapillary flow. The flow field was studied by flow visualization. Several thermistor probes were placed in the fluid to measure the temperature distribution. The temperature distribution along the liquid free surface was measured by an infrared imager. Tests were conducted over a range of heating powers, laser beam diameters, and free surface shapes. In conjunction with the experiments an extensive numerical modeling of the flow was conducted. In this paper some results of the velocity and temperature measurements with flat and curved free surfaces are presented and they are shown to agree well with the numerical predictions.

Ostrach, Simon↗
NASA NTRS1990

Surface tension and viscosity from damped free oscillations of viscous droplets

Damped oscillations of a viscous droplet in vacuum or in an inert gas of negligible density are considered. The dependence of the complex decay factor on the properties of the liquid is investigated for the first time, and numerical results are compared with earlier studies for special cases. A new method is developed to determine both surface tension and viscosity from a single experiment in which the damping rate and frequency of oscillations are measured. The procedure to determine surface tension and viscosity from oscillating levitated liquids is outlined, and results presented for various modes of shape oscillations.

Suryanarayana, P. V. R.↗
NASA NTRS1988

Hardware development for the surface tension driven convection experiment aboard the USML-1 spacelab mission

The Surface Tension Driven Convection Experiment is a Space Transportation System flight experiment to study both transient and steady thermocapillary fluid flows aboard the USML-1 Spacelab mission planned for March 1992. Hardware is under development to establish the experimental conditions and perform the specified measurements, for both ground based research and the flight experiment in a Spacelab single rack. Major development areas include an infrared thermal imaging system for surface temperature measurement, a CO2 laser and control system for surface heating, and for flow visualization, a He-Ne laser and optical system in conjunction with an intensified video camera. For ground based work the components of each system were purchased or designed, and tested individually. The three systems will be interfaced with the balance of the experimental hardware and will constitute a working engineering model. A description of the three systems and examples of the component performance is given along with the plans for the development of flight hardware.

Pline, A. D.↗
NASA NTRS1989

Hardware development for the Surface Tension Driven Convection Experiment aboard the USML-1 Spacelab mission

The Surface Tension Driven Convection Experiment is a Space Transportation System flight experiment to study both transient and steady thermocapillary fluid flows aboard the USML-1 Spacelab mission planned for March 1992. Hardware is under development to establish the experimental conditions and perform the specified measurements, for both ground based research and the flight experiment in a Spacelab single rack. Major development areas include an infrared thermal imaging system for surface temperature measurement, a CO2 laser and control system for surface heating, and for flow visualization, a He-Ne laser and optical system in conjunction with an intensified video camera. For ground based work the components of each system were purchased or designed, and tested individually. The three systems will be interfaced with the balance of the experimental hardware and will constitute a working engineering model. A description of the three systems and examples of the component performance is given along with the plans for the development of flight hardware.

Pline, A. D.↗
NASA NTRS1960

The Surface-Tension Method of Visually Inspecting Honeycomb-Core Sandwich Plates

When one face of a metal-honeycomb-core sandwich plate is heated or cooled relative to the other, heat transfer through the core causes the temperature on each face at the lines of contact with the core to be slightly different from that on the rest of the face. If a thin liquid film is applied to the face, the variation of surface tension with temperature causes the liquid to move from warmer to cooler areas and thus to develop a pattern corresponding to the temperature pattern on the face. Irregularities in the pattern identify the locations where the core is not adequately bonded to the face sheet. The pattern is easily observed when a fluorescent liquid is used and illumination is by means of ultraviolet light. Observation in ordinary light is also possible when a very deeply colored liquid is used. A method based on the use of a thermographic phosphor to observe the temperature pattern was found to be less sensitive than the surface-tension method. A sublimation method was found to be not only less sensitive but also far more troublesome.

Katzoff, Samuel↗
NASA NTRS1985

Surface Tension Induced Instabilities in Reduced Gravity: the Benard Problem

A Benard convection experiment has been set up, and the onset of convection in shallow layers of silicone oil two millimeters or less deep has been studied. The onset has been observed visually or has been determined by the break in the heat transfer curve which accompanies the onset of convection. The outcome of these experiments has been very surprising, from the point of view of theoretical expectations. The onset of convection at temperature differences far below the critical value for fluid depths smaller than 2mm was observed. The discrepancy between experiments and theory increases with decreasing fluid depth. According to theoretical considerations, the effects of surface tension become more important as the fluid depth is decreased. Actually, one observes that the onset of convection tales place in two stages. There is first an apparently surface tension driven instability, occuring at subcritical temperature differences according to conventional theory. If then the temperature difference is increased, a second instability occurs which transform the first pattern into conventional strong hexagonal Benard cells. The second instability is in agreement with the critical temperature gradients predicted by Nield.

Koschmieder, E.↗
NASA NTRS1980

Influence of solidification on surface tension driven convection

The effect of solidification on the onset of surface tension driven convection in a reduced gravity environment is studied. Two simple but physically realistic configurations representing the solidification of a simple material are analyzed. The analysis shows that as a result of the solidification process the critical Marangoni number is shifted to lower values indicating that solidification has a destabilizing effect upon the liquid. From this result it is concluded that convection can be brought about in the liquid phase at lower Marangoni numbers when solidification is present than when it is not. The effects of other parameters introduced by the solidification process are analyzed and discussed.

Antar, B. N.↗
NASA NTRS1991

Particle image velocimetry for the surface tension driven convection experiment using a particle displacement tracking technique

The Surface Tension Driven Convection Experiment (STDCE) is a Space Transportation System flight experiment to study both transient and steady thermocapillary fluid flows aboard the USML-1 Spacelab mission planned for 1992. One of the components of data collected during the experiment is a video record of the flow field. This qualitative data is then quantified using an all electronic, two-dimensional particle image velocimetry technique called particle displacement tracking (PDT) which uses a simple space domain particle tracking algorithm. The PDT system is successful in producing velocity vector fields from the raw video data. Application of the PDT technique to a sample data set yielded 1606 vectors in 30 seconds of processing time. A bottom viewing optical arrangement is used to image the illuminated plane, which causes keystone distortion in the final recorded image. A coordinate transformation was incorporated into the system software to correct this viewing angle distortion. PDT processing produced 1.8 percent false identifications, due to random particle locations. A highly successful routine for removing the false identifications was also incorporated, reducing the number of false identifications to 0.2 percent.

Wernet, Mark P.↗
NASA NTRS1991

Particle image velocimetry for the Surface Tension Driven Convection Experiment using a particle displacement tracking technique

The Surface Tension Driven Convection Experiment (STDCE) is a Space Transportation System flight experiment to study both transient and steady thermocapillary fluid flows aboard the USML-1 Spacelab mission planned for 1992. One of the components of data collected during the experiment is a video record of the flow field. This qualitative data is then quantified using an all electronic, two-dimensional particle image velocimetry technique called particle displacement tracking (PDT) which uses a simple space domain particle tracking algorithm. The PDT system is successful in producing velocity vector fields from the raw video data. Application of the PDT technique to a sample data set yielded 1606 vectors in 30 seconds of processing time. A bottom viewing optical arrangement is used to image the illuminated plane, which causes keystone distortion in the final recorded image. A coordinate transformation was incorporated into the system software to correct this viewing angle distortion. PDT processing produced 1.8 percent false identifications, due to random particle locations. A highly successful routine for removing the false identifications was also incorporated, reducing the number of false identifications to 0.2 percent.

Wernet, Mark P.↗
NASA NTRS1982

Determination of surface tension at the phase interface

A method was developed for determining the surface tension coefficient at the interface of two immiscible liquids or of a gas and a liquid. Basic in this method is the measurement of the capillary rise of a droplet of one of the phases placed on the surface of the other phase. It is shown that the capillary rise is a function of the surface energy of the droplet and the viscous friction of the phases. A mathematical model of the dynamics of a liquid droplet is supported by experiments.

Dobychin, Y. I.↗
NASA NTRS1998

Exact Solution to Stationary Onset of Convection Due to Surface Tension Variation in a Multicomponent Fluid Layer With Interfacial Deformation

Stationary onset of convection due to surface tension variation in an unbounded multicomponent fluid layer is considered. Surface deformation is included and general flux boundary conditions are imposed on the stratifying agencies (temperature/composition) disturbance equations. Exact solutions are obtained to the general N-component problem for both finite and infinitesimal wavenumbers. Long wavelength instability may coexist with a finite wavelength instability for certain sets of parameter values, often referred to as frontier points. For an impermeable/insulated upper boundary and a permeable/conductive lower boundary, frontier boundaries are computed in the space of Bond number, Bo, versus Crispation number, Cr, over the range 5 x 10(exp -7) less than or equal to Bo less than or equal to 1. The loci of frontier points in (Bo, Cr) space for different values of N, diffusivity ratios, and, Marangoni numbers, collapsed to a single curve in (Bo, D(dimensional variable)Cr) space, where D(dimensional variable) is a Marangoni number weighted diffusivity ratio.

Skarda, J. Raymond Lee↗