Search NASA⌕ Search

SEARCH · Search NASA

Results for “TDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Reduced defect recovery in self-ion damaged W due to simultaneous deuterium exposure during annealing

Deuterium (D) plasma exposure during annealing of self-ion damaged tungsten (W) is shown to exhibit reduced defect recovery when compared to annealing without D plasma exposure. In these experiments, samples were first damaged with 20 MeV W ions. Next, samples were annealed either with or without simultaneous D 2 plasma exposure. The simultaneous annealed samples were first decorated by D 2 plasma at 383 K prior to ramping up to an annealing temperature of 473, 573, 673, or 773 K and held for 1 h with concurrent plasma exposure. The vacuum annealed samples each had a corresponding temperature history but without D 2 plasma treatment. Finally, all samples were exposed to D 2 plasma at 383 K to decorate any remaining defects. Nuclear reaction analysis and thermal desorption spectroscopy (TDS) shows that the simultaneous plasma-exposed and annealed samples exhibited virtually no defect recovery at annealing temperatures of up to 673 K, and had higher D retention than found in the vacuum annealed samples. TDS results indicate that only the lowest detrapping energy defects recover at an 773 K anneal for the simultaneous plasma annealed samples, while the vacuum annealed samples showed defect recovery at all anneal temperatures. Furthermore, this experiment clearly demonstrates that D occupied defects can significantly reduce or eliminate defect annealing in W, and is consistent with the existence of synergistic plasma exposure/displacement damage effects in fusion-energy relevant plasma facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of topological Dirac fermions and surface states in superconducting BaSn3

The interplay between topological electronic structure and superconductivity has attracted tremendous research interests recently as they could induce topological superconductivity (TSCs) which may be used to realize topological qubits for quantum computation. Among various TSC candidates, superconducting BaSn 3 (T c ~ 4.4K) has been predicted to be a topological Dirac semimetal (TDS) hosting two pairs of Dirac points along the Γ-A direction. Here, by combining the use of angle-resolved photoemission spectroscopy and ab initio calculations, we identified the predicted topological Dirac fermions and confirmed the TDS nature of the compound. In addition, we observed surface states connecting the Dirac points. Our observations demonstrate BaSn 3 as a superconductor with nontrivial topological electronic structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Terahertz time-domain spectroscopy imaging of pancreatic ductal adenocarcinoma tissues

Pancreatic ductal adenocarcinoma (PDAC) ranks among the malignancies with the highest fatality and morbidity rates. This is predominantly attributable to an absence of understanding the intricate and diverse microenvironment of the tumor. We use terahertz time-domain spectroscopy (THz-TDS) imaging in transmission geometry to probe ex-vivo the heterogenous microenvironment of the genetically modified murine PDAC tissue that closely resembles the PDAC heterogeneity in human malignancy. We introduced a maximum a-posteriori probability estimation algorithm to objectively the tumor’s heterogenous microenvironment using the average values of refractive index and absorption coefficient within the useable terahertz bandwidth as imaging markers. Furthermore, direct comparison of stained histopathologic images and the refractive index and the absorption coefficient high-resolution, two dimensional maps of the same PDAC samples confirms the high potential of the THz-TDS method for tumor tissue characterization.

absorption↗

High-speed fiber-coupled terahertz time-domain spectroscopy system using a bias-free plasmonic source

We demonstrate a high-speed fiber-coupled terahertz time-domain spectroscopy (THz-TDS) system using a bias-free plasmonic terahertz source. The system is powered by a compact, low-power femtosecond fiber laser oscillator that drives a dual-branch fiber amplifier to pump and probe a plasmonic terahertz source and detector, respectively. A polarization-maintaining, fiber-coupled optical delay line is employed to precisely control the temporal offset between the pump and probe beams through a compact, robust platform. Operating in the self-similar amplification regime, the fiber amplifiers are engineered to mitigate nonlinear pulse distortion and dispersion while delivering robust, high-energy pulses at a 1560-nm wavelength, with an output power exceeding 326 mW. In reflection mode, the THz-TDS system achieves a peak dynamic range of 81 dB and a bandwidth greater than 3.5 THz at a scan rate of 3.75 Hz. The utility of the system for rapid sensing is further demonstrated by quantifying the porosity and density of pharmaceutical tablets through measurements of their physical thickness and effective refractive index.

Jiang, Xinghe [University of California, Los Angel↗

Revised Kimberlina Groundwater Simulations

Kimberlina Groundwater Qaulity Simulations (Version 3: 2015 October) by Lawrence Livermore National Labratory. Submitted to the EDX team at the National Energy Technology Laboratory for research use. This dataset contains 562 updated groundwater quality simulations based on the Kimberlina site. It is a six-layer model including the aquifers and aquitards inbetween the ground surface and the reservoir. The input files and associated leakage information for these simulations are included in the zip file "nrap_kim_well31_fluxes and inputs.tar.gz". These 562 simulations are the successful results out of 1000 monte carlo simulations, with time length greater than 5 years. Each simulation consists 6 output files, therefore, there are 3372 files (6*562) in total. One single example simulation of full time length (200 year) is also provided in the zip file "single_simulation_200yr_sim0012.tar.gz". These 6 groundwater quality parameters are: - pH (use absolute value) - TDS (mg/kg) - Pressure (Pa) - CO2 Liquid Saturation (fraction range 0.0-1.0) - CO2 Gas Concentration (mol/L) - CO2 Liquid Concentration (mol/kg) Their correponding file names, take the first simulation for example, are: ph0001.ntab (for pH) , tds0001.ntab (for TDS), usnt0001.p.ntab (for pressure), usnt0001.s_liquid.ntab (for liquid saturation), usnt0001.c_co2_gas.ntab (for CO2 gas concentration) and usnt0001.c_co2_liquid.ntab (for CO2 liquid concentration). Each output file contains at least 19 columns (variables). The total number of columns depends on the simulation time length. The column data include the information of numerical records, geologic location and sizes and the simulated parameter values over time. The first 13 variables are about numerical records and relative geologic information for a simulation grid: 1. index: simulation index 2. i: the ith grid of x-axis 3. j: the jth grid of y-axis 4. k: the kth grid of z-axis 5. element_ref: element type reference 6. nuft_ind: nuft index 7. x: grid location in the x axis direction 8. y: grid location in the y axis direction 9. z: grid location in the z axis direction 10. dx: grid length in the x axis direction 11. dy: grid length in the y axis direction 12. dz: grid length in the z axis direction 13. volume: volume of the simulation grid The rest (14, 15, 16...) variables are the simulated parameter values over time, take pH as an example, are: 14. ph000y: initial pH value. 15. ph001y: simulated pH value at the end of the 1st year. 16. ph002y: simulated pH value at the end of the 2nd year. ... (and so on)... The zip input files have the input fluxes of brine and CO2 (in kg/s) allocated to model layers 1,2,3 and 5 (layers 4 and 6 are assumed to be no-flow aquitards) through the following nodes: (src1 WELL 7 7 25 25 10 32) #Etchegoin (src2 WELL 7 7 25 25 33 72) #Macoma Chanac (src3 WELL 7 7 25 25 73 83) #Santa Margarita Mclure (src4 WELL 7 7 25 25 84 89) #Fruitvale Round Mountain (aquitard) (src5 WELL 7 7 25 25 90 96) #Olcese Sand (thief zone) (src6 WELL 7 7 25 25 97 99) #tremblor Freeman (aquitard) ex: brn1 is assigned to src 1 from i=(7,7), j=(25,25), k=(10,32) Edited by Ya-Mei Yang at National Energy Technology Laboratory

brine leakage↗

Maximizing the Proppant Carrying and Viscoelastic Properties of the Bakken Hypersaline-Produced Water with High-Viscosity Friction Reducers for Sustainable Applications

Summary The development and production of unconventional reservoirs, such as the Bakken Formation, have become a resolved mystery for operators in North America since the arrival and advancement of horizontal drilling and hydraulic fracturing technologies. As a result, unconventional reservoir assets became the central focus of the oil and gas industry at the state, national, and global levels. The produced water from these activities in the Bakken Formation have high salt contents (110,000–350,000 ppm) total dissolve solids (TDS) and can pose significant challenges to the environment if not treated. Deep injection into disposal wells is the routine method used to get rid of the Bakken produced water. However, there have been some concerns that unrestrained injections, in addition to polluting the groundwater, could potentially lead to seismic activities either at the time of injection or in the near future. To diminish the environmental impacts that may be associated with induced seismicity, including the reduction of the costs of water acquisition, the produced water can be treated and reused in the hydraulic fracturing processes. Also, the treated water could be used for irrigation purposes, for power generation, and coal mining operations. The issues of waste water and residual oil high in TDS are challenges yet to be effectively addressed despite preceding research and studies on advancing produced water technologies. The goal of this study is to explore all applicable ways by which the produced water from the Bakken Formation can serve as a replacement base fluid for use with polymers like the high-viscosity friction reducers (HVFRs) to create hydraulic fracturing fluids that can be stable with reservoir conditions and also be able to minimize environmental impacts and cost of operations. Experimental investigations using the high-salinity produced water from the Bakken Formation with HVFRs were carried out. The studies included a base case that served as a bench mark for comparing the effectiveness of the other scenarios. The results indicate that the Bakken hyper-saline produced water can withstand effect of heavy metals, salinity, hardness and remain stable through different shear rates (66–330 s−1) when treated with higher dosages [4–8 gal/1,000 gal (gpt)] of HVFRs. Filtration and dilution were the only methods used on the Bakken Formation produced wate for this research

Engineering↗

Intensified Flue Gas Desulfurization Water Treatment for Reuse, Solidification, and Discharge

The goal of this final project report is to summarize the work conducted on project DE-FE0031555. In accordance with the Statement of Project Objectives (SOPO), the University of Kentucky Center for Applied Energy Research (UK CAER) (Recipient) developed a hybrid electrochemical-membrane technology for treating wet flue gas desulfurization (WFGD) blowdown from coal-fired power generation plants that (1) removes government-regulated species and total suspended solids (TSS) via electrocoagulation with solid/liquid separation to avoid further treatments by a biological method specifically for selenium, and (2) reduces total dissolved solids (TDS) in a nanofiltration unit to promote water recycle and reduce freshwater intake. Additional technological configurations were pursued, including (1) nanofiltration combined with zeolite dewatering for a near-zero liquid discharge (ZLD) scenario, and (2) polishing discharge from zeolite dewatering using capacitive deionization (CDI) with 90+% salt rejection to produce water with less than 100ppm TDS for more beneficial use. Project results verified that UK CAER’s hybrid approach addressed the complexities of WFGD blowdown with simplified unit operation at relatively low capital investment by demonstrating: (1) an effective in-situ generated solid sorbent material, green-rust (GR), that specifically removes regulated dissolved species in WFGD blowdown, including selenium, arsenic, and nitrates; (2) a low-cost, high flux nanofiltration treatment that removes both monovalent and divalent species at >80% rejection to adequately provide water recycle and extend the life of FGD equipment by mitigating chloride aided pitting corrosion mechanisms; and (3) a solidification and stabilization process using pozzolanic agents that retain regulated species and satisfy the Resource Conservation and Recovery Act (RCRA) leachate requirements. UK CAER proved electrocoagulation with GR to be an intensified solution for effluent limit guidelines (ELG), and based on preliminary techno-economic analysis (TEA), in comparison to DOE’s Case 1 for Biological Wastewater Treatment that had a purchased equipment cost (PEC) of $\$$5.26 million and a Total plant cost (TPC) of $\$$30.0 million, the EC process had a PEC of $\$$2.67 million and the TPC of $\$$17.0 million. While the electricity consumption for Case 1 was 53 kW, it was 110 kW for the EC process due to dissolving iron for a three-stage reaction design. However, electricity consumption for the EC process could be significantly reduced by adopting a counter-current reactor design for at least a 6-stage chemical reaction operation.

01 COAL, LIGNITE, AND PEAT↗

NRAP-Open-IAM: FutureGen2 Component Models

This report describes the development and testing of three component models for NRAP-Open-IAM, the National Risk Assessment Partnership’s open-source integrated assessment model. The FutureGen2 Lookup Table Reservoir component model is based on interpolation of data from a set of lookup tables. The lookup tables contain pressures and saturations predicted by multiphase flow simulations performed with a reservoir simulator. The FutureGen2 Above Zone Monitoring Interval (AZMI) component is a surrogate model that can be used to estimate the impact that carbon dioxide (CO 2 ) and brine leaks from the CO 2 storage reservoir at the FutureGen 2.0 site might have had on overlying aquifers or monitoring units were a leak to occur. The model estimates the size of “impact plumes” according to five metrics: pH, Total Dissolved Solids (TDS), pressure, dissolved CO 2 and temperature. The FutureGen2 Aquifer component is similar, but is limited to four metrics: pH, Total Dissolved Solids (TDS), pressure, and dissolved CO 2 . The input parameters for each model are the same, but the Aquifer component is applicable to depths between 100 m and 700 m and the AZMI component is applicable from depths between 700 m and 1050 m.

42 ENGINEERING↗

An Innovative Zero-Liquid Discharge Intermediate-Cold-Liquid Eutectic-Freeze Desalination System

A novel freeze desalination technology is presented for purification of water produced from various industrial processes, including oil and gas extraction. The main innovative idea is introducing a water-immiscible intermediate-cold-liquid (ICL) medium which absorbs the cold from a refrigeration cycle and transfers it to a freezing chamber where it is mixed with brine. The cold ICL enters the freezing chamber at temperatures between -10°C to -30°C. Precooled brine in injected into the freezing chamber and pure water freezes out of the brine upon mixing with the ICL. The rate of freezing inside the chamber is controlled by adjusting the flow rate of the cold ICL relative to the inlet brine. Both eutectic freeze and non-eutectic freezing are possible by controlling the temperature of the freezing chamber. The solid-liquid slurry created in the freezing chamber flows to a filter separation unit after passing through a separation column. The ice crystals are separated from the liquid by a rotary filter device. The collected ice is rinsed by a centrifugal unit. The rinsed ice is melted to produce fresh water. The developed technology resolves the issues common to current freeze-desalination systems while offering superior heat transfer performance ascribed to direct-contact between the cooling medium and the brine in addition to producing solid salt and pure water. The system operates under atmospheric pressure. The low operation temperature minimizes the corrosion issues common in systems exposed to brine. Also, due to the low operating temperature, there are no concerns about evaporation of volatile organics from the produced water during the treatment. The developed technology effectively eliminates the use of chemicals for pretreatment of brine. The system can be constructed from commercially available components. Extensive testing using a lab-scale prototype by using synthetic brine and actual produced water with TDS values from 50,000 ppm to 300,000 ppm showed that freshwater could be achieved with relatively small dependency on the quality of the input brine. The quality of the treated water was found to be mainly a function of the duration of the centrifugal process. Treated water with TDS as low as 200 ppm could be achieved in the tests. Thermo-economic modeling coupled with system level thermochemical process model were developed for prediction of the LCOW. The LCOW was predicted to be $\$$0.50 to $\$$0.90 per barrel of produced water. The potential markets for deployment of the technology are the oil and gas, in-land thermoelectric powerplants, RO desalination plants, and mining industry.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Geochemical characterization of lithium deposition in fossil energy wastes

Lithium is a critical mineral used in rechargeable batteries for electric vehicles (EVs) and future modernization of electric grids with sensitive supply chains that are subject to volatility. Therefore, methods to recover lithium from domestic unconventional sources are actively being pursued in the United States. Herein, we report on the lithium recovery potential from four fossil energy waste feedstocks: oil and gas drill cuttings (sample number n = 16); oil and gas produced waters (n > 200) from Marcellus, Bakken and Permian basins; coal byproducts (n>20), such as coal ash; and acid mine drainage treatment solids (AMD solids). Select solid samples underwent sequential extraction to explore lithium hosting phases and simple organic and inorganic acid extraction to explore lithium recovery potential. Our preliminary results found lithium concentrations up to 440 mg/kg in select AMD treatment solids and up to 300 mg/L in Marcellus Shale produced waters, demonstrating these sources have lithium yield potentials comparable to conventionally mined lithium ores and brines. Sequential extractions revealed that lithium is mostly associated with clay and silicate phases in shale drill cuttings, whereas lithium resides in Fe,Mn-oxide reducible phases in AMD solids. Further, the lithium content in produced waters has a strong linear relationship with total dissolved solid (TDS) levels in three separate oil and gas basins. At the same TDS level, Marcellus Shale produced waters contain more lithium compared to Bakken Shale and Permian Basin waters, with higher percentages of Ca and Mg, major cations that might impact lithium recovery efficiencies. Our study demonstrates the heterogeneity of lithium hosts from different fossil energy wastes. Characterization results will inform future lithium recovery from these different feedstocks.

Stuckman, Mengling↗

Geochemical and Microbial Dynamics of Hydrogen in a Methane Storage Reservoir

Hydrogen has been identified as a flexible energy carrier with zero or negative emission across multiple energy systems, and existing natural gas infrastructure could be leveraged if hydrogen gas (H2) was blended with methane (CH4). For example, subsurface methane storage reservoirs could be slightly modified to also store hydrogen if a methane/hydrogen blend were injected. However, the compatibility of methane storage reservoirs to include H2 injection has not been fully demonstrated, and this could lead to geochemical and microbiological reactions that alter the reservoir and stored gas content. It is essential that we understand the impact of H2 gas on the biogeochemistry of subsurface storage reservoirs before deploying large-scale H2-CH4 storage, We collected produced fluid from two separate methane storage reservoirs in the Southwestern US. First, we completed a baseline analysis of the biogeochemistry through qPCR, 16S rRNA sequencing, metagenomic sequencing, and geochemical analysis. Each reservoir was found to have unique geochemical conditions and a unique microbial community structure, with Site 1 having a higher TDS and an abundance of Shewanella and Site 2 having a lower TDS and high abundance of Eubacterium and Acetobacterium. Next, we ran a series of high pressure, high temperature reactors under hydrogen storage conditions with the biological sample from one of the storage reservoirs and a 20% H2-80% CH4 gas blend for up to 7 days. Our results show a decrease of hydrogen by 5% in reactors as early as 1-3 days. Previous hydrogen storage work has linked subsurface microorganisms with methanogenesis hydrogen sulfide production, acid production, and microbial corrosion. Our results show minimal change in the fluid chemistry, with the exception of a decrease in dissolved sulfate concentrations. Taxonomic sequencing demonstrated the presence of microorganisms capable of iron redox, acid generation, and hydrogen sulfide production throughout the reactors, suggesting microbial hydrogen consumption may occur through various metabolic pathways. This work demonstrates that site-specific geochemistry and microbiology may impact the efficiency of hydrogen storage in methane storage reservoirs.

environmental microbiology↗

Tracking and data system support for the Mariner Mars 1971 mission. Volume 2: First trajectory correction maneuver through orbit insertion

The Deep Space Tracking and Data System activities in support of the Mariner Mars 1971 project from the first trajectory correction maneuver on 4 June 1971 through cruise and orbit insertion on 14 November 1971 are presented. Changes and updates to the TDS requirements and to the plan and configuration plus detailed information on the TDS flight support performance evaluation and the preorbital testing and training are included. With the loss of Mariner 8 at launch, a few changes to the Mariner Mars 1971 requirements, plan, and configuration were necessitated. Mariner 9 is now assuming the former mission plan of Mariner 8, including the TV mapping cycles and a 12-hr orbital period. A second trajectory correction maneuver was not required because of the accuracy of the first maneuver. All testing and training for orbital operations were completed satisfactorily and on schedule. The orbit insertion was accomplished with excellent results.

Textor, G. P.↗

Tracking and data system support for the Mariner Mars 1971 mission. Volume 3: Orbit insertion through end of primary mission

The Tracking and Data System (TDS) Support for the Mariner Mars 1971 Mission final report contains the deep space tracking and data acquisition activities in support of orbital operations. During this period a major NASA objective was accomplished: completion of the 180th revolution and 90th day of data gathering with the spacecraft about the planet Mars. Included are presentations of the TDS flight support pass chronology data for each of the Deep Space Stations used, and performance evaluation for the Deep Space Network Telemetry, Tracking, Command, and Monitor Systems. With the loss of Mariner 8 at launch, Mariner 9 assumed the mission plan of Mariner 8, which included the TV mapping cycles and a 12-hr orbital period. The mission plan was modified as a result of a severe dust storm on the surface of Mars, which delayed the start of the TV mapping cycles. Thus, the end of primary mission date was extended to complete the TV mapping cycles.

Barnum, P. W.↗

Thermally regenerative hydrogen/oxygen fuel cell power cycles

Two innovative thermodynamic power cycles are analytically examined for future engineering feasibility. The power cycles use a hydrogen-oxygen fuel cell for electrical energy production and use the thermal dissociation of water for regeneration of the hydrogen and oxygen. The TDS (thermal dissociation system) uses a thermal energy input at over 2000 K to thermally dissociate the water. The other cycle, the HTE (high temperature electrolyzer) system, dissociates the water using an electrolyzer operating at high temperature (1300 K) which receives its electrical energy from the fuel cell. The primary advantages of these cycles is that they are basically a no moving parts system, thus having the potential for long life and high reliability, and they have the potential for high thermal efficiency. Both cycles are shown to be classical heat engines with ideal efficiency close to Carnot cycle efficiency. The feasibility of constructing actual cycles is investigated by examining process irreversibilities and device efficiencies for the two types of cycles. The results show that while the processes and devices of the 2000 K TDS exceed current technology limits, the high temperature electrolyzer system appears to be a state-of-the-art technology development. The requirements for very high electrolyzer and fuel cell efficiencies are seen as determining the feasbility of the HTE system, and these high efficiency devices are currently being developed. It is concluded that a proof-of-concept HTE system experiment can and should be conducted.

Morehouse, J. H.↗

Natural language processing and advanced information management

Integrating diverse information sources and application software in a principled and general manner will require a very capable advanced information management (AIM) system. In particular, such a system will need a comprehensive addressing scheme to locate the material in its docuverse. It will also need a natural language processing (NLP) system of great sophistication. It seems that the NLP system must serve three functions. First, it provides an natural language interface (NLI) for the users. Second, it serves as the core component that understands and makes use of the real-world interpretations (RWIs) contained in the docuverse. Third, it enables the reasoning specialists (RSs) to arrive at conclusions that can be transformed into procedures that will satisfy the users' requests. The best candidate for an intelligent agent that can satisfactorily make use of RSs and transform documents (TDs) appears to be an object oriented data base (OODB). OODBs have, apparently, an inherent capacity to use the large numbers of RSs and TDs that will be required by an AIM system and an inherent capacity to use them in an effective way.

Hoard, James E.↗

Signal processing applied to photothermal techniques for materials characterization

There is a need to make noncontact measurements of material characteristics in the microgravity environment. Photothermal and photoacoustics techniques offer one approach for attaining this capability since lasers can be used to generate the required thermal or acoustic signals. The perturbations in the materials that can be used for characterization can be detected by optical reflectance, infrared detection or laser detection of photoacoustics. However, some of these laser techniques have disadvantages of either high energy pulsed excitation or low signal-to-noise ratio. Alternative signal processing techniques that have been developed can be applied to photothermal or photoacoustic instrumentation. One fully coherent spread spectrum signal processing technique is called time delay spectrometry (TDS). With TDS the system is excited using a combined frequency-time domain by employing a linear frequency sweep excitation function. The processed received signal can provide either frequency, phase or improved time resolution. This signal processing technique was shown to outperform other time selective techniques with respect to noise rejection and was recently applied to photothermal instrumentation. The technique yields the mathematical equivalent of pulses yet the input irradiances are orders of magnitude less than pulses with the concomitant reduction in perturbation of the sample and can increase the capability of photothermal methods for materials characterization.

Rooney, James A.↗

Shuffling foot points and magnetohydrodynamic discontinuities in the solar wind

ISEE three-field and plasma data are used to investigate the frequency of occurrence of isolated, large-amplitude rotational (RD) and tangential (TD) discontinuities in different types of solar wind flow. It is found that there are relatively more TDs in solar wind that originates in closed field regions and is ejected into interplanetary space by coronal transients than in the solar wind that originates in open field regions. The speed of the wind from open field regions is approximately linearly related to the number of RDs per hour; such a relation does not exist for the wind associated with coronal mass ejections. These results are consistent with the hypothesis that the convection-driven shuffling of magnetic foot points at the solar surface leads to TDs, magnetic reconnection, and heating of the corona on closed field lines, while in the open field regions the disturbances created by the shuffling are carried off by waves which contribute to the acceleration of the solar wind.

Neugebauer, M.↗

An XPS study of the stability of Fomblin Z25 on the native oxide of aluminum

Thin films of Fomblin Z25, a perfluoropolyalkylether lubricant, were vapor deposited onto clean, oxidized aluminum and sapphire surfaces, and their behavior at different temperatures was studied using x ray photoelectron spectroscopy (XPS) and thermal desorption spectroscopy (TDS). It was found that the interfacial fluid molecules decompose on the native oxide at room temperature, and continue to decompose at elevated temperatures, as previous studies had shown to occur on clean metal. TDS indicated that different degradation mechanisms were operative for clean and oxidized aluminum. On sapphire substrates, no reaction was observed at room temperature. Our conclusion is that the native oxide of aluminum is neither passive nor protective towards Fomblin Z25. At high temperatures (150 C) degradation of the polymer on sapphire produced a debris layer at the interface with a chemical composition similar to the one formed on aluminum oxide. Rubbing a Fomblin film on a single crystal sapphire also induced the decomposition of the lubricant in contact with the interface and the formulation of a debris layer.

Herrera-Fierro, Pilar↗