In situ TEM measurement of activation volume in ultrafine grained gold
Quantitative in situ TEM true activation volume measurements in nanoscale specimens with simultaneous observations of plastic deformation mechanisms.
Gupta, Saurabh↗
SEARCH · Search NASA
Results for “TEM”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thermal stability of self-assembled ordered three-phase Au–BaTiO 3 –ZnO nanocomposite thin films via in situ heating in TEM
Thermal stability of an ordered three-phase Au–BaTiO 3 –ZnO vertically aligned nanostructure by both ex situ annealing under air and vacuum conditions, and in situ heating in TEM in vacuum has been demonstrated.
Misra, Shikhar↗
In Situ High-Temperature TEM Observation of Inconel Corrosion by Molten Chloride Salts with N 2 , O 2 , or H 2 O
Here, in situ transmission electron microscopy (TEM) diffraction and imaging techniques are used to monitor and quantify corrosion of Inconel-625 by pure molten chloride salts (MgCl 2 – NaCl – KCl) at 500 °C–800 °C in 1.0 atm inert N 2 or pure O2, or by salts which are controllably hydrated in a high vacuum chamber. The isothermal corrosion rate R in inert N 2 increases from 203 ± 30 μ m year –1 at 700 °C to 463 ± 30 μ m year –1 at 800 °C. An oxygen ambient causes a six-fold increase to R = 1261 ± 170 μ m year –1 at 700 °C. Salt hydration dramatically accelerates corrosion to R > 3 × 10 5 μ m year –1 at 700 °C while it leads to a more moderate R = 95 ± 20 and 486 ± 30 μ m year –1 at 500 °C and 600 °C, respectively. These isothermal corrosion rates indicate that the molten chloride corrosion is significantly accelerated by salt hydration at temperatures above 600 °C, where corrosion is aggravated by increased generation and solubility of corrosive HCl gases. Hence, to reduce rate of corrosion it is important to both avoid incorporation of H 2 O into the system at each stage and ensure proper flushing of the system before increasing the temperature beyond 600 °C. Compositional analysis of the corroded cells indicate that corrosion in O 2 ambient is dominated by oxidation of metals by O 2 gas dissolved in the chloride melt, but corrosion in H 2 O ambients is caused by chlorination of metals by dissolved HCl gas and MgOH + ions. So, to reduce rate of corrosion, steps should be taken to tailor chloride melt compositions that has low solubility for HCl and O 2 . All of our corroded samples exhibit passive-protective oxide layers of Cr, Mg, and Ni. In addition, distinct volatile compounds of Ni, Mo and Cr involving NiCl 2 , (Na,K) 2 MoO 4 and CrO 2 (OH) 2 are detected in N 2 , H 2 O, and O 2 ambients, respectively. We believe that corrosion acceleration can be minimized by minimizing formation of volatile by-products or promoting reactions that could convert these volatile compounds to solid phases, as these volatile compounds led to destruction of protective oxide layers.
14 SOLAR ENERGY↗
14YWT TEM images for LAUR [Images]
Transmission Electron Microscopy (TEM) images attached here are for machine learning study, and these will be uploaded to outer cloud at LANL.
97 MATHEMATICS AND COMPUTING↗
In-Situ Helium Implantation and TEM Investigation of Radiation Tolerance to Helium Bubble Damage in Equiaxed Nanocrystalline Tungsten and Ultrafine Tungsten-TiC Alloy
The use of ultrafine and nanocrystalline materials is a proposed pathway to mitigate irradiation damage in nuclear fusion components. Here, we examine the radiation tolerance of helium bubble formation in 85 nm (average grain size) nanocrystalline-equiaxed-grained tungsten and an ultrafine tungsten-TiC alloy under extreme low energy helium implantation at 1223 K via in-situ transmission electron microscope (TEM). Helium bubble damage evolution in terms of number density, size, and total volume contribution to grain matrices has been determined as a function of He+ implantation fluence. The outputs were compared to previously published results on severe plastically deformed (SPD) tungsten implanted under the same conditions. Large helium bubbles were formed on the grain boundaries and helium bubble damage evolution profiles are shown to differ among the different materials with less overall damage in the nanocrystalline tungsten. Compared to previous works, the results in this work indicate that the nanocrystalline tungsten should possess a fuzz formation threshold more than one order of magnitude higher than coarse-grained tungsten.
36 MATERIALS SCIENCE↗
TEM Characterization of Neutron Irradiated HfAl3-Al Composite Specimens
Particles comprised of a thermal neutron absorbing material (HfAl3) are dispersed in a metal matrix material with high thermal conductivity (aluminum) to conduct the heat generated by neutron capture away from the fuel and materials. This metal matrix composite is very promising for use as a conduction-cooled neutron absorber and has the potential to be useful as a shroud or heat sink for testing advanced fast reactor fuels and materials in an existing thermal reactor. To design and optimize the absorber block system for advanced reactor designs, fundamental understanding of the irradiation effect on material properties is necessary. This dataset contains TEM characterization results of neutron irradiated HfAl3-Al composite specimens. It is focused on the irradiation induced defects (dislocation lines and loops) characterization using the on-zone axis bright field STEM technique. This data was collected using a FEI Tecnai G2 F30 S/TEM at the Microscopy and Characterization Suite (MaCS), Center for Advanced Energy Studies (CAES).
Guillen, Donna↗
TEM Characterization of Neutron Irradiated HfAl3-Al Composite Specimens
Particles comprised of a thermal neutron absorbing material (HfAl3) are dispersed in a metal matrix material with high thermal conductivity (aluminum) to conduct the heat generated by neutron capture away from the fuel and materials. This metal matrix composite is very promising for use as a conduction-cooled neutron absorber and has the potential to be useful as a shroud or heat sink for testing advanced fast reactor fuels and materials in an existing thermal reactor. To design and optimize the absorber block system for advanced reactor designs, fundamental understanding of the irradiation effect on material properties is necessary. This dataset contains TEM characterization results of neutron irradiated HfAl3-Al composite specimens. It is focused on the irradiation induced defects (dislocation lines and loops) characterization using the on-zone axis bright field STEM technique. This data was collected using a FEI Tecnai G2 F30 S/TEM at the Microscopy and Characterization Suite (MaCS), Center for Advanced Energy Studies (CAES).
Guillen, Donna↗
Using In Situ TEM Helium Implantation and Annealing to Study Cavity Nucleation and Growth
Not Available
36 MATERIALS SCIENCE↗
In-Situ TEM study of microstructural evolution in proton irradiated single crystal UO2 under high-temperature annealing
Not Available
36 MATERIALS SCIENCE↗
Visualizing time-dependent microstructural and chemical evolution during molten salt corrosion of Ni-20Cr model alloy using correlative quasi in situ TEM and in situ synchrotron X-ray nano-tomography
In situ monitoring of corrosion processes is important to fundamentally understand the kinetics and evolution of materials in harsh environments. A quasi in situ transmission electron microscopy technique was utilized to study microstructural and chemical evolution of a Ni-20Cr disc sample 6 exposed to molten KCl-MgCl 2 salt for 60 s in consecutive 20 s iterations. In situ synchrotron X-ray nano-tomography was performed to characterize the morphological evolution of a Ni-20Cr microwire exposed to molten KCl-MgCl 2 . Here, both techniques captured key corrosion events and revealed mechanisms at different time and length scales, potentially bringing greater insights and 10 deeper understanding beyond conventional analysis.
36 MATERIALS SCIENCE↗
SEM and TEM data of nuclear graphite and glassy carbon microstructures
Not Available
36 MATERIALS SCIENCE↗
Microstructure and phase evolution in the U-10Zr fuel investigated by in situ TEM heating experiments
The development of U-Zr metallic nuclear fuel for fast spectrum reactors is impacted by a lack of mechanistic understanding of the fuel behavior evolution under thermal irradiation conditions, despite previous works providing substantial fuel performance data. This work uses in-situ transmission electron microscopy heating experiments to study phase and microstructural evolution in several unirradiated U-10Zr specimens during rapid heating ramps (from room temperature to 1000 °C). The starting a-U + bcc-(Zr, U) eutectic microstructure began to decompose above 600 °C. The decomposition initiated from the bcc (U,Zr) phase. Similar results were observed for all specimens even when fabricated by different routes (e.g., cold rolled or annealed). As a result, the impact of observed microstructure and phase evolutions at high temperatures on fuel fabrication and in-pile fuel transient test was also discussed.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
TEM characterization of two variants of fuel cladding chemical interaction in a HT-9 Clad U-10Zr Fuel. Variant 1: FCCI with a Zr Rind
Here, this study investigated the fuel cladding chemical interaction (FCCI), a key factor that limits operational temperature and burnup, in an HT-9 clad U-10Zr nuclear fuel sample irradiated to a high burnup of 13.1 at.% at a time-averaged peak inner cladding temperature (PICT) of 530 °C. Previous results showed this fuel sample exhibited two distinct levels of FCCI at d. This paper analyzed the FCCI at an azimuthal position showing an interdiffusion layer of <10 µm using transmission electron microscopy to examine chemical and crystallographic nature of phases at the fuel-cladding interface at the nanoscale level. A ZrC layer and a Zr 3 Si phase were identified at the interface; these, along with the relatively low local temperature, potentially contributed to limit interdiffusion, behaving as inhibitors for deleterious interactions. Lanthanides (Ln) partially consumed the ZrC layer and interacted with Fe, forming a Zr-Ln compound and a (Zr,Ce)Fe 2+x phase while also infiltrating up to 4 µm into the cladding. Neither U nor Zr were observed in the cladding, whereas Fe diffused up to 3–5 µm in the fuel. Fe infiltration formed a ternary U-Zr-Fe ε-phase and likely promoted the precipitation of a Cr-rich α’ phase on the cladding interface. Additionally, a Cr-rich χ-phase, likely formed by the dissociation of pre-existing M 23 C 6 carbide precipitates, was identified about 2–5 µm from the fuel-cladding interface. Irradiation-induced nano-voids were also observed in the HT-9 bulk. These findings provide critical insights into FCCI mechanisms at representative irradiation conditions, essential for developing models simulating in-pile metallic fuel behaviors for next-generation reactors.
36 - MATERIALS SCIENCE↗
Automated phase segmentation and quantification of high-resolution TEM image for alloy design
In the alloy design and development process, a wealth of atomically resolved structural high-resolution transmission electron microscopy (HRTEM) images are produced. Identifying the different nano-precipitate phases and tracking their evolution under various compositions and during manufacturing or post-processing requires hundreds of HRTEM images and thousands of precipitates. The nanoscopic phase information labeling and analysis purely relies on humans are prohibitively costly and time-consuming, sometimes not reliable because of the lack of authoritative knowledge. Here, in this work, we develop a novel unsupervised machine learning approach coupled with adaptive computer vision techniques with features in the Fourier space to automatically determine the number of phases and segment/quantify the phases with nanoscale resolution, allowing for quantitative correlation between nanostructure formation, processing and functional properties. To automate the phase extraction/quantification and ascertain its applicability, we have applied the developed framework to the HRTEM images from several alloy systems, processing conditions, image magnifications, and phase types and morphologies (precipitates, nano-twins, stacking faults, crystalline matrix, and amorphous structures) for verification. This study paves the road for compression, visualization, and translation of raw image structural data into physically relevant information in real-time with minimal human supervision. It shows the promise of enabling high-throughput materials characterization for the acceleration of alloy manufacturing and design.
36 MATERIALS SCIENCE↗
Observations of crystal strains in filler and QI particles through TEM examination – Effect of processing and grain size
Not Available
36 MATERIALS SCIENCE↗
Radiolysis and Radiation-Driven Dynamics of Boehmite Dissolution Observed by In Situ Liquid-Phase TEM
We report over the last several decades, there have been several studies examining the radiation stability of boehmite and other aluminum oxyhydroxides, yet less is known about the impact of radiation on boehmite dissolution. Here, we investigate radiation effects on the dissolution behavior of boehmite by employing liquid-phase transmission electron microscopy (LPTEM) and varying the electron flux on the samples consisting of either single nanoplatelets or aggregated stacks. We show that boehmite nanoplatelets projected along the [010] direction exhibit uniform dissolution with a strong dependence on the electron dose rate. For nanoplatelets that have undergone oriented aggregation, we show that the dissolution occurs preferentially at the particles at the ends of the stacks that are more accessible to bulk solution than at the others inside the aggregate. In addition, at higher dose rates, electrostatic repulsion and knock-on damage from the electron beam causes delamination of the stacks and dissolution at the interfaces between particles in the aggregate, indicating that there is a threshold dose rate for electron-beam enhancement of dissolution of boehmite aggregates.
54 ENVIRONMENTAL SCIENCES↗
Cu–Ni Oxidation Mechanism Unveiled: A Machine Learning-Accelerated First-Principles and in Situ TEM Study
Here, the development of accurate methods for determining how alloy surfaces spontaneously restructure under reactive and corrosive environments is a key, long-standing, grand challenge in materials science. Using machine learning-accelerated density functional theory and rare-event methods, in conjunction with in situ environmental transmission electron microscopy (ETEM), we examine the interplay between surface reconstructions and preferential segregation tendencies of CuNi(100) surfaces under oxidation conditions. Our modeling approach predicts that oxygen-induced Ni segregation in CuNi alloys favors Cu(100)-O c(2 × 2) reconstruction and destabilizes the Cu(100)-O (2√2 × √2)R45° missing row reconstruction (MRR). In situ ETEM experiments validate these predictions and show Ni segregation followed by NiO nucleation and growth in regions without MRR, with secondary nucleation and growth of Cu 2 O in MRR regions. Our approach based on combining disparate computational components and in situ ETEM provides a holistic description of the oxidation mechanism in CuNi, which applies to other alloy systems.
36 MATERIALS SCIENCE↗
In Situ TEM for Structural and Chemical Evolutions of Bimetallic Pt–Ni Nanoparticles at Elevated Temperatures: Implications for Heterogeneous Catalysis
Platinum-based bimetallic nanoparticles (NPs) are of great interest for their applications in catalysis. The catalytic properties of these NPs are significantly dependent on their morphology, structure, and composition, whose response to thermal input remains challenging to be fully understood. This study investigates the thermally induced structural and chemical evolutions of single-crystalline Pt-Ni NPs using in situ transmission electron microscopy. The observed morphological evolution includes the facet development from a truncated octahedron to a spherical-like isotropic shape, followed by the formation of pancake-like ellipsoid shape at high temperatures due to surface atom migration and interfacial wetting enabled by the particle-substrate interaction. Comparative investigations by in situ scanning transmission electron microscopy with energy dispersive X-ray spectroscopy mapping elucidate that the solid-solution compositional configuration can be retained over a large temperature range, while core-shell NPs undergo irreversible solid-solution transitions through chemical homogenization at elevated temperatures. Finally, these findings elucidate the effect of thermal input on structural evolution and compositional redistribution of Pt-Ni bimetallic NPs, offering valuable insights into the design of heterogeneous catalysts.
25 ENERGY STORAGE↗