Search NASA⌕ Search

SEARCH · Search NASA

Results for “TENSILE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Uniaxial tensile mechanical properties from a scratch on ultra-fine grained tungsten

We demonstrate that surface-based mechanical testing can be used to quantify a wide range of mechanical properties determined using traditional uniaxial tension experiments. These include mapping of dynamic stress–strain behaviour, which can be used as a screening tool for uniaxial tensile ductility (uniform elongation), fracture toughness (K C ), which is shown to be in good agreement with reported plane-strain K IC , as well work-hardening exponents (n), activation volumes (V) energies (Q) and strain-rate sensitivity (m) exponents as a function of temperature. Advantages of the surface-based approach are the ability to work with significantly smaller volumes and accommodate processing defects like pores, voids and cracks. These methods are applied to ultra-fine grained tungsten (average grain size of 650 nm), as it is an ideal candidate for alloy development efforts in advanced energy systems. Tungsten is a useful baseline as it exhibits a near-ambient temperature (approx. 200°C) ductile-to-brittle transition temperature (DBTT), enabling validation efforts for the proposed methods, and extraordinary material properties, including the highest melting temperature of any metal and complex temperature and strain-rate dependencies linked to transitions in dislocation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Process-Structure-Property Relations for As-Deposited Solid-State Additively Manufactured High-Strength Aluminum Alloy

Solid-state additive manufacturing methods provide innovative solutions to circumvent problems associated with materials susceptible to hot cracking by avoiding liquid solid phase transformations. In this work, the process parameter influence on microstructural evolution and mechanical response of a fully dense aluminum alloy 7050 (AA7050) component manufactured via a rapid, solid-state additive manufacturing process known as Additive Friction Stir Deposition (AFS-D) was quantified for the first time. Three sections (starting dwell, transient, crossover of roads) of the deposition that exhibit differing thermomechanical processing histories were evaluated for the resulting microstructure and mechanical response. The microstructural characterization was performed on the as-deposited AA7050 via Electron Backscatter Diffraction (EBSD), TEM, optical microscopy, and Scanning Electron Microscopy (SEM). The microstructural characterization revealed refined constituent particles and grains throughout the as-deposited AA7050 microstructure. Furthermore, quasi-static tensile experiments were conducted in both the build and transverse directions, in order to quantify the orientation influence on tensile properties of the as-deposited AA7050 build. Spatially dependent tensile properties were observed in the material due to heat input variation coarsening of secondary phases towards the initial layers of the AFS-D build. Post-mortem analysis revealed that voids nucleated and coalesced from the overgrowth of the strengthening precipitates present in the material, resulting in fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An additively manufactured AlCuMnZr alloy microstructure and tensile mechanical properties

In this study, selective laser melting (SLM) was used to fabricate an AlCuMnZr alloy. The microstructural features that resulted from additive manufacturing (AM) were significantly refined compared to the corresponding cast alloy features. A combination of fine equiaxed and columnar grains along with in-situ formation of θ' precipitates during AM leads to enhanced yield strength (up to 300°C) in the as-fabricated AM alloy. The refinement of brittle intermetallics and a bimodal grain size distribution leads to improved tensile elongation in the AM alloy. The results illustrate the microstructural advantages that can result from additive processing over conventionally processed microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Epoxy Coating of Biofiber: An Effective Modifier of Biofiber Physical and Flow Properties for Improved Tensile Behavior of Biofiber-Reinforced Biocomposite

Biocomposites combine renewable, plant-based fibers with degradable polymers and are an attractive option for sustainable, lightweight, and cost-effective materials with a low carbon footprint, especially for large-scale additive manufacturing. One of the major challenges in the widespread adoption of biocomposites is that their mechanical performance is significantly inferior to that of synthetic composites. Surface treatment is a common and effective technique to improve the mechanical properties of the biofibers used in biocomposites. This study aims to investigate the physical and flow properties of surface-treated biofibers, as well as the tensile properties of their PLA-based biocomposite, to gain insights into how surface treatment changes the fiber‘s characteristics and biocomposite‘s mechanical properties. Surface treatment was created using a two-component epoxy system by reacting poly(bisphenol A-co-epichlorohydrin) glycidyl end-capped (PBG) and dicyandiamide (DICY). The treatment was tested on two different biofibers (loblolly pine and corn stover fibers) with three different PBG/DICY molar ratios (0.25, 0.5, and 2). Results showed that surface-treated fibers improved the tensile strength and Young‘s modulus of the biocomposites. Loblolly pine biocomposites from fibers treated with a PBG/DICY ratio of 0.25 exhibited the best tensile properties. The surface treatment resulted in a more loosely dispersed fiber bulk structure, as evidenced by less fiber agglomeration into smaller particle sizes, higher fiber sphericity, and lower loose bulk density. This can enhance stress distribution and the overall mechanical performance of the biocomposites. Additionally, surface-treated fibers exhibited better dynamic flow properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Small Punch Testing of Molybdenum-99 Targets

Northstar Medical Radioisotopes is developing an accelerator-based method to produce 99 Mo, which is a parent isotope of the commonly used 99m Tc medical isotope. The Mo targets being designed for the accelerator will be produced from enriched 100 Mo, also known as aMo . Pressed and sintered powder feedstock is used to fabricate aMo targets, producing 29 mm disk-shaped targets. The targets are subjected to 1–6 days in line of an electron beam with subsequent dissolution of the disk to retain the 99 Mo, which decays to 99m Tc at radio-pharmacies. The press and sinter method is advantageous because the inherent porosity produced by this method enables increased surface area and therefore increased flow of dissolution media, decreasing the dissolution time and reducing the need for a highly acidic media. Although porosity aids in dissolution, it reduces the mechanical strength and ductility. Targets require good mechanical integrity when subjected to the conditions in the accelerator. Therefore, Northstar is seeking methods to rapidly test disk samples after fabrication to assure mechanical performance metrics are achieved. This report details the design and testing of a small punch test (SPT) that accommodates the 29 mm disk. Initial data were used to relate the SPT data to tensile properties, such as the yield strength (YS), ultimate tensile strength (UTS), and total elongation to failure. Although the SPT has been established as a somewhat reliable method for testing metallic materials, few studies have applied the SPT to refractory materials such as Mo. Based on tensile testing performed at Oak Ridge National Laboratory on different Mo samples, correlation between the Mo tensile and SPT properties could be performed, establishing a standard calibration that could be applied to other Mo samples. To test the efficacy of the SPT with Mo, multiple different disk batches were fabricated under different conditions (e.g., pressure, lubricant) with commercially available pure Mo powder. Generally, only a UTS could be well defined because the press and sinter disks failed under brittle fracture, making it difficult to determine the YS and elongation. Compared with disks fabricated with aMo powder, the aMo samples underperformed their pure nat Mo counterparts. This report summarizes the current status of the SPT, but further evaluation is needed before it can be applied as a reliable quality assurance tool.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2025

Material extrusion with integrated compression molding of NdFeB/SmFeN nylon bonded magnets using small- and large-scale pellet-based 3D-printers

High-density bonded rare-earth magnets are manufactured using pellet-fed additive manufacturing (AM)/material extrusion and an integrated additive manufacturing-compression molding (AM-CM) process. Neodymium iron boron – samarium iron nitride in polyamide 12 (NdFeB-SmFeN/PA12) of 93 % weight fraction (65 % volume fraction) are used for the study. The mechanical properties (tensile strength and modulus), magnetic properties (maximum energy density, coercivity, remanence) are reported. Manufacturing parameters such as layer height, barrel temperatures, screw speed and gantry feed rate are optimized to obtain the highest possible density of the magnets using a small-scale desktop material extrusion printer. Large scale integrated additive manufacturing-compression molding (AM-CM) is then utilized to increase the density of the magnets by reducing porosity defects common in the material extrusion process. The density of as-printed magnets was 5.2 g/cm 3 with a BH max value of 124.14 kJ/m 3 , tensile strength of 20 MPa and a modulus of 2 GPa. AM-CM increased the density of the compound by 5.5 % (5.49 g/cm 3 ). The reduction in porosity was confirmed using X-ray tomography (XCT). Improvement in mechanical strength of the material was also observed, with an increase in tensile strength of 25 % (25.09 MPa) and increase in tensile modulus of 275 % (5.49 GPa). Scanning electron microscopy showed increased particle-matrix adhesion with the integrated AM-CM process.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical Property Measurements of HFIR-irradiated FM and ODS Alloys

This report provides a summary of the post-irradiation examination of the tensile properties of three ODS ferritic alloys, 14YWT-SM13, 9YWTV-PM2 and OFRAC, and two HT9 ferritic/martensitic steels, one with low N content and the other with high N content. The neutron irradiations were conducted in the flux trap of the High Flux Isotope Reactor as part of the A dditive M anufacturing, O xide Dispersion Strengthened Alloys and W rought Steels (AMOW) irradiation campaign. Sub-sized tensile specimens fabricated from each material were exposed to nominal target temperatures and neutron doses of 300°C, 385°C, and 525°C and 8 dpa, 16 dpa, and 50 dpa, respectively.

14YWT-SM13, 9YWTV-PM2, and OFRAC, and two HT9 ferr↗
DOE OSTI2021

Summary of Previous Mechanical Test Data on ODS Alloys 14YWT and OFRAC up to 1000ºC

The Nanostructured Ferritic Alloys (NFA) 14YWT and OFRAC were developed for future fission and fusion nuclear energy reactors requiring high-temperature mechanical properties that are tolerant to extreme neutron irradiation environments. The NFA contain a high concentration of Ti-, Y- and O-enriched nanoclusters (NC) and ultra-fine grains to achieve high temperature strength and creep properties and high sink strength for trapping irradiation induced point defects to minimize hardening and swelling and transmutated He atoms to form intragranular nano-size bubbles that prevent formation of coarse bubbles on grain boundaries that cause embrittlement. The mechanical properties of 14YWT and OFRAC have been acquired from tensile and creep tests conducted in the past at Oak Ridge National Laboratory. The development of 14YWT started in 2000, resulting in the production of numerous heats. Tensile properties were obtained from eleven heats of 14YWT from room temperature to 800ºC. Tensile data for the SM10 heat of 14YWT was extended to 1,000ºC. Initial development of OFRAC occurred in 2016. Tensile tests conducted from room temperature to 800ºC revealed similar properties of OFRAC with those obtained from the newer generation of 14YWT heats. The creep properties of 14YWT-SM10 evaluated using constant stress tensile and load time-to-failure tests at 800ºC showed low minimum creep rates with stresses of 200 and 100 MPa. The single time-to-failure test of 14YWT-SM10 at 800ºC and 100 MPa was terminated after 20,357 hours with no specimen failure and a low creep strain of ~0.24 %. The creep properties of OFRAC determined from strain-rate jump tests at were similar those of 14YWT-SM10. The stress exponent for 14YWT and OFRAC at 800ºC are similar and are consistent with threshold stress behavior. Since both 14YWT and OFRAC are candidates for fuel cladding in future fast reactors, several fabrication studies were recently conducted and have successfully demonstrated that thin wall tubes can be fabricated from 14YWT and OFRAC by cold pilger rolling and high precision tube rolling. The high temperature mechanical properties and feasibility of fabricating thin wall tubes make 14YWT and OFRAC candidates for application as heat pipes in advanced micro-reactors. The purpose of this report is to summarize the previously obtained tensile and creep data at temperatures up to 1000ºC for NFA 14YWT and OFRAC that have been acquired over the past 20 years at ORNL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Evaluation of coated steels in supercritical CO 2

The carburizing supercritical CO 2 (sCO 2 ) environment limits the use of lower cost steels in the lower temperature (450–650°C) portions of the sCO 2 Brayton cycle because of concerns about internal carburization and embrittlement. Results on a ferritic–martensitic steel and conventional and advanced austenitic steels at 450–650°C in 30 MPa sCO 2 with and without 1% O 2 and 0.1% H 2 O additions have indicated that sCO 2 environments will have lower maximum operating temperatures compared to steam plants. Pack Al and Cr coatings were evaluated at 650°C on T91 and 316H substrates and showed some benefit for up to 2000 h at 650°C, especially without impurities. However, characterization indicated Al 2 O 3 was not formed and Cr-rich carbides formed in the Cr coatings. With the addition of impurities in the sCO 2 , the coatings were less protective at 650°C. Subsequent exposures at 600°C in sCO 2 showed similar behavior. Postexposure evaluations included measuring the bulk C content and room temperature tensile properties. Finally, improvements were indicated but the tensile results were complicated by the high temperature pack coating process affecting the substrate properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rapid data acquisition and machine learning-assisted composition design of functionally graded alloys via wire arc additive manufacturing

Abstract The lack of high-quality datasets in materials science hinders artificial intelligence (AI)-driven alloy design. To address this challenge, wire arc additive manufacturing (WAAM) was employed to fabricate graded alloys, generating extensive data for machine learning (ML)-assisted property prediction. ML models were developed using high-throughput experiments, computational models, and genetic algorithm to optimize feature selection, successfully predicting hardness and porosity. The ML model demonstrated its efficacy by designing a gradient alloy with enhanced properties. However, scaling up revealed uncertainties in tensile property and porosity due to differences in size and thermal conditions between the designed alloy build and the gradient print used to construct the ML model. This underscores the need for uncertainty quantification and process optimization in WAAM-driven alloy design. Our work advances AI-integrated additive manufacturing, offering a rapid approach to exploring process–structure–property relationships and accelerating materials development.

Wang, Xin↗
DOE OSTI2023

DeePMD-kit v2: A software package for deep potential models

DeePMD-kit is a powerful open-source software package that facilitates molecular dynamics simulations using machine learning potentials known as Deep Potential (DP) models. This package, which was released in 2017, has been widely used in the fields of physics, chemistry, biology, and material science for studying atomistic systems. The current version of DeePMD-kit offers numerous advanced features, such as DeepPot-SE, attention-based and hybrid descriptors, the ability to fit tensile properties, type embedding, model deviation, DP-range correction, DP long range, graphics processing unit support for customized operators, model compression, non-von Neumann molecular dynamics, and improved usability, including documentation, compiled binary packages, graphical user interfaces, and application programming interfaces. This article presents an overview of the current major version of the DeePMD-kit package, highlighting its features and technical details. Additionally, this article presents a comprehensive procedure for conducting molecular dynamics as a representative application, benchmarks the accuracy and efficiency of different models, and discusses ongoing developments.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

The microstructure effects on irradiation response of ferritic – martensitic steels

Microstructural optimization to achieve greater mechanical strength has been one of the focuses in ferritic–martensitic steels development. However, these optimized microstructures’ effects on the radiation response are not well known. In this work, two ferritic–martensitic steels (9Cr-NbMo and 9Cr-Ta) underwent neutron irradiation in the High Flux Isotope Reactor, and their room-temperature post-irradiation tensile properties and microstructure evolutions were investigated and compared. These two steels exhibit similar pre-irradiation tensile behavior, and their yield strengths are higher than that of other ferritic–martensitic steels by about 200–250 MPa. Microstructural characterization on pre-irradiated materials reveals a smaller grain size in 9Cr-Ta (2.8 ± 0.3 μm in 9Cr-Ta versus 4.3 ± 0.5 μm in 9Cr-NbMo) but higher dislocation density and precipitate density in 9Cr-NbMo. As is common for ferritic–martensitic steels at low irradiation temperatures (less than about 0.45T m ), irradiation-induced hardening at 400 °C was observed for both alloys. Irradiation at 490 °C causes the two alloys to exhibit different tensile behavior: 9Cr-Ta softens by 208 MPa in yield stress, whereas 9Cr-NbMo maintains strength. Additionally, microstructural characterizations were performed, including precipitate growth, dislocation, and defect formation. Using the barrier hardening model for microstructure–property correlation, the softening in irradiated 9Cr-Ta is primarily attributed to the significant dislocation recovery, while the strength lost from the slight dislocation recovery in 9Cr-NbMo was compensated by the additional strength from the irradiation-induced cavities. The microstructure effect (primarily precipitate, dislocation and boundary) on the radiation response is discussed herein.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Deformation Strengthening of Uranium and Dilute Uranium Alloys

The strength and ductility of uranium and dilute uranium alloys can be substantially improved by deformation strengthening. The yield strength of unalloyed uranium can be nearly doubled by rolling in the vicinity of 250°C. The embrittling effect of hydrogen is also overcome, eliminating the need for vacuum outgassing to obtain good ductility. Significant differences in longitudinal versus transverse tensile properties result, in part, from texture introduced by unidirectional rolling. Warm rolling of U-2.3%Nb results in both traditional strain hardening and a significant Bauschinger effect, resulting in differences between tensile and compressive yield strength. A similar combination of strain hardening and Bauschinger effect also occurs in deformation strengthened U-0.75%Ti. Warm rolling of U-0.75%Ti results in significantly better combinations of tensile yield strength and ductility than can be obtained by conventional age hardening. Warm rolling prior to aging also reduces the loss of ductility which typically accompanies conventional age hardening. Here, an approach is developed in which the effects of prior deformation on tensile and compressive yield strengths are analyzed in terms of texture, long-range dislocation, and Bauschinger effects. The Bauschinger effect is shown to vary in sign with the type of deformation, thus providing opportunities to tailor tensile and compressive properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Dissimilar Material Joining via Interlocking Metasurfaces

Background The integration of dissimilar materials poses a significant challenge in engineering, necessitating innovative solutions for robust and reliable joining. Interlocking metasurfaces (ILMs) are a new joining technology comprising arrays of autogenous features patterned across two surfaces that interlock to form robust structural joints. Objective Here, this study elucidates the factors influencing the tensile performance of ILM joints formed between dissimilar materials. Methods We employed parametric optimization to identify optimal unit cell geometries for maximal yield strength based on the hypothesis that the elastic tensile properties of the materials are the primary determinants of tensile performance. Experimental validation was performed by mechanically testing the theorized optimal ILM geometry and a range of ILM geometries to capture the overall behavior trends of joints between two additively manufactured polymers, VeroPureWhite (VW) and RGDA8430-DM (8430). Results Experimental validation of optimized designs revealed that additional factors, e.g. flexural strength and localized plasticity, also strongly influenced the tensile performance of T-slot ILMs joining dissimilar materials. The proposed optimal design remained the best performer. Conclusions This study demonstrates the viability of ILMs as a joining method for dissimilar materials. ILMs can join dissimilar materials with no loss in joint yield strength compared to joints composed solely of the weaker of the two constitutive materials. ILMs demonstrated their potential as a versatile and effective joining technology in diverse engineering applications.

Elbrecht, Benjamin James [Sandia National Laborato↗
DOE OSTI2025

High-Entropy Alloys for Accelerator Beam Window Applications

Development of novel high-entropy alloys (HEAs) is currently underway for potential use as beam windows in future multi-megawatt target systems at Fermilab. HEAs encompass a new class of materials with a vast design space allowing for material properties to be tailored for particular applications and to potentially offer improved resistance to beam-induced radiation damage and thermal shock effects. The alloy systems being studied consist of several compositions of AlCoCrMnTiV with 4 6 component elements. These alloys are all predicted by CALPHAD simulation to have a single-phase BCC crystal structure and low density, with some compositions displaying ordered, nanoscale precipitates. This presentation will briefly discuss alloy design and synthesis before giving a detailed description of the characterization studies of these HEAs in both the pristine state and post-irradiation by low-energy heavy ions to high damage levels. Electron microscopy techniques to quantify elemental homogeneity and composition, determine grain size, shape, and orientation, and quantify lattice parameters, defect structures and precipitate phases are all being used to study alloy microstructures. Mechanical properties of the alloys at the microscale will be reported. The evolution of these properties as a function of radiation damage will also be described. Bulk thermal characteristics of these HEAs have been tested to measure specific heat capacity and coefficient of thermal expansion as a function of temperature. To determine bulk tensile properties a miniature tensile testing apparatus is under development; it s commissioning will be covered briefly. The talk will conclude with our plans for alloy down-selection.

Burleigh, A. [Fermilab]↗
DOE OSTI2023

Biodegradable High-Molecular-Weight Poly(pentylene adipate- co -terephthalate): Synthesis, Thermo-Mechanical Properties, Microstructures, and Biodegradation

Poly(pentylene adipate-co-terephthalate) (PPAT) is a promising biobased and biodegradable polymer that can replace polyethylene in flexible packaging films where biodegradability is desired. High-molecular-weight (100K–145 KDa) aliphatic–aromatic polyester PPAT was successfully synthesized, and the effects of reaction conditions on molecular weight were reported. PPAT polyesters were characterized for polymer compositions, number-average unit length, thermal transitions, and rheological properties. PPAT compression-molded films were characterized for crystallinity and tensile properties to correlate micro- and macroproperties. PPAT compression-molded films exhibited up to a 76% higher tensile modulus than compression-molded films from poly(butylene adipate-co-terephthalate) (PBAT), making PPAT films potentially comparable with compression-molded films from linear low-density polyethylene (LLDPE). Finally, PPAT is biodegradable in soil and freshwater environments with estimated 90% biodegradation times of 504–580 and 604–845 days, respectively, while PBAT takes 971 days in soil and 395 days in freshwater.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effects of processing temperature, pressure, and fiber volume fraction on mechanical and morphological behaviors of fully-recyclable uni-directional thermoplastic polymer-fiber-reinforced polymers

This work explores a type of composite called thermoplastic polymer-fiber-reinforced polymers (PFRPs), often referred to as self-reinforced composites (SRCs). A representative PFRP was exemplified using unidirectional (UD) ultra-high-molecular-weight polyethylene (UHMWPE) fibers embedded in a high-density polyethylene (HDPE) matrix. The effects of compression molding temperature and pressure on the mechanical and morphological behaviors of the filament-wound PFRPs with various fiber volume fractions (V f ) were experimentally investigated. The results elucidate the evolution of morphologies and tensile properties of the PFRPs due to thermal melting, fiber misalignment from pressure, and (V f )-induced structural variance, which has not been comprehensively reported yet. The highest specific tensile strength and modulus of the PFRP laminae reach 600 MPa/(g/cm 3 ) and 31 GPa/(g/cm 3 ), respectively. These properties are comparable to glass-/aramid-fiber-reinforced polymers (GFRPs, GFRTPs, AFRPs, and AFRTPs), with PFRPs exhibiting better ductility (specific strain at peak load ≈ 4%/(g/cm 3 )) than other common polymer composites. The motivation for this work was the high recyclability of PFRPs, which can be recycled by melting both the fibers and the matrix, and then reshaped them for re-manufacturing composites to maximize the efficiency in material reuse. This process simplifies the implementation of closed-loop recycling, re-manufacturing, and reuse to support sustainability in composites. This work aims to contribute to advancing thermoplastic PFRPs for their potential applications in various industries.

36 MATERIALS SCIENCE↗