Search NASA⌕ Search

SEARCH · Search NASA

Results for “TRANSMISSION LOSS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Additive Manufacturing of Frequency-Agile W-Band Packaging

Abstract —In this paper we demonstrate a fully additively manufactured packaged W-band amplifier with integrated bypass capacitors. This package was fabricated using a chip-first approach and aerosol jet printing. Package substrates (dielectrics), conductors and interconnects are printed around a bare die attached to a carrier. This package uses shaped ramp interconnects, allowing for frequency agnostic package performance of the interconnect with no impedance discontinuity, within the physical limits of the printer. High dielectric constant thin films of a polymer-matrix nanocomposite for bypass capacitors were printed using multi-material aerosol jet printing. The maximum measured packaged gain is 14.9 dB in the W-band, compared to the maximum bare die gain of 15.5 dB in the same frequency range. From 75 - 92 GHz, the average package loss is 1.1 dB including 3 mm transmission line, interconnects, and a GSG launch structure correlating to an average loss of 0.37 dB/mm.

Additive manufacturing, aerosol jet printing, hete↗
DOE OSTI2022

Revealing local order via high energy EELS

Short range order (SRO) is critical in determining the performance of many important engineering materials. However, accurate characterization of SRO with high spatial resolution – which is needed for the study of individual nanoparticles and at material defects and interfaces – is often experimentally inaccessible. Here, we locally quantify SRO via scanning transmission electron microscopy with extended energy loss fine structure analysis. Specifically, we use novel instrumentation to perform electron energy loss spectroscopy out to 12 keV, accessing energies which are conventionally only possible using a synchrotron. Our data is of sufficient energy resolution and signal-to-noise ratio to perform quantitative extended fine structure analysis, which allows determination of local coordination environments. To showcase this technique, we investigate a multicomponent metallic glass nanolaminate and locally quantify the SRO with <10 nm spatial resolution; this measurement would have been impossible with conventional synchrotron or electron microscopy methods. Finally, we discuss the nature of SRO within the metallic glass phase, as well as the wider applicability of our approach for determining processing–SRO–property relationships in complex materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Learning-Based Load Control to Support Resilient Networked Microgrid Operations

Microgrids have proven to be an effective option for increasing the resiliency of critical end-use loads during extreme events. Building on past operational experiences, some microgrid operators are examining the potential to network microgrids to further improve resiliency. However, the frequency deviations experienced on isolated microgrids during transient events, such as switching operations, step increases in load, and loss of generation, are significantly larger than those typically seen on bulk transmission systems. The larger frequency deviations can cause a loss of inverter-connected assets, resulting in a loss of power to critical end-use loads. This paper presents a method of mitigating the impact of transient events by engaging end-use loads using Grid-Friendly Appliance TM (GFA) controllers. An online, i.e., real-time, device-level algorithm is presented, which adjusts individual GFA controller frequency set-points based on the operational characteristics of each end-use load, and on the changing grid dynamic characteristics. The presented method improves the dynamic stability of the networked microgrid operations while minimizing the interruptions to end-use loads. The presented work is validated with dynamic simulations using a modified version of the IEEE 123-node test system with three microgrids, using the GridLAB-D TM simulation environment.

Radhakrishnan, Nikitha↗
DOE OSTI2025

Multi-Gigawatt Electric Highway

Ultra-Compact Electrical Transmission Lines are a new transmission line technology that uses large, hollow, aluminum beams to carry current instead of thin wires. Capacity is 4.5 times higher, power losses are 3 times lower, and cost per mile is a little lower than conventional lines. Resilience and reliability are higher. The beams are enclosed within concrete walls and out of the weather, protected from high winds, ice storms, fires, and lightning. The 230 kV version is 9 feet high x 11 feet wide and can use existing rights of way next to existing transmission lines or highways. With a little landscaping, these transmission lines are not an eyesore and will be much easier to permit on existing rights of way.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Neutral but Impactful: Gallium Cluster-Induced Nanopores from Beam-Blanked Gallium Ion Sources

Neutral atoms originating from liquid metal ion sources are an often-overlooked source of contamination and damage in focused ion beam microscopy. Beyond ions and single atoms, these sources also generate atom clusters. While most studies have investigated charged clusters, here we demonstrate that neutral clusters are also formed. These neutral clusters bypass the electrostatic beam blanking system, allowing them to impinge on samples even when the ion beam is blanked. We investigate this phenomenon using thin (≤20 nm) freestanding membranes of hexagonal boron nitride, silicon, and silicon nitride as targets. Randomly dispersed nanopores that form upon neutral cluster exposure are revealed. The average nanopore diameter is ∼2 nm with a narrow size distribution, suggesting that the atom clusters have a preferred size. Various electron microscopy techniques are used to characterize the nanopores, including high-resolution transmission electron microscopy, multislice ptychography, and electron energy-loss spectroscopy. Finally, we show how electron irradiation in the transmission electron microscope can be used to both remove any amorphous material that may clog the pores and to controllably grow the pores to specific sizes. Tunable nanopores such as these are interesting for nanofluidic applications requiring size-selective membranes.

Byrne, Dana O↗
DOE OSTI2023

Combining variational autoencoders and physical bias for improved microscopy data analysis *

Electron and scanning probe microscopy produce vast amounts of data in the form of images or hyperspectral data, such as electron energy loss spectroscopy or 4D scanning transmission electron microscope, that contain information on a wide range of structural, physical, and chemical properties of materials. To extract valuable insights from these data, it is crucial to identify physically separate regions in the data, such as phases, ferroic variants, and boundaries between them. In order to derive an easily interpretable feature analysis, combining with well-defined boundaries in a principled and unsupervised manner, here we present a physics augmented machine learning method which combines the capability of variational autoencoders to disentangle factors of variability within the data and the physics driven loss function that seeks to minimize the total length of the discontinuities in images corresponding to latent representations. Our method is applied to various materials, including NiO-LSMO, BiFeO 3 , and graphene. The results demonstrate the effectiveness of our approach in extracting meaningful information from large volumes of imaging data. The customized codes of the required functions and classes to develop phyVAE is available at https://github.com/arpanbiswas52/phy-VAE.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

The influence of electrochemical cycling protocols on capacity loss in nickel-rich lithium-ion batteries

The transition towards electric vehicles and more sustainable transportation is dependent on lithium-ion battery (LIB) performance. Ni-rich layered transition metal oxides, such as NMC811 (LiNi 0.8 Mn 0.1 Co 0.1 O 2 ), are promising cathode candidates for LIBs due to their higher specific capacity and lower cost compared with lower Ni content materials. However, complex degradation mechanisms inhibit their use. In this work, tailored aging protocols are employed to decouple the effect of electrochemical stimuli on the degradation mechanisms in graphite/NMC811 full cells. Using these protocols, impedance measurements, and differential voltage analysis, the primary drivers for capacity fade and impedance rise are shown to be large state of charge changes combined with high upper cut-off voltage. Focused ion beam-scanning electron microscopy highlights that extensive microscale NMC particle cracking, caused by electrode manufacturing and calendering, is present prior to aging and not immediately detrimental to the gravimetric capacity and impedance. Scanning transmission electron microscopy electron energy loss spectroscopy reveals a correlation between impedance rise and the level of transition metal reduction at the surfaces of aged NMC811. The present study provides insight into the leading causes for LIB performance fading, and highlights the defining role played by the evolving properties of the cathode particle surface layer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

In Situ Study of Resistive Switching in a Nitride‐Based Memristive Device

Abstract Resistive switching (RS) devices with ultra‐low‐voltage threshold and reliable switching repeatability exhibits great potential applications in energy‐efficient data storage and neuromorphic computing. Understanding switching mechanisms at nanoscale is critical to design RS devices with improved performance. In this work, a lamella memristive device using focused ion beam (FIB) method based on the metal/TiO x /TiN/Si structure device is fabricated. In situ transmission electron microscopy (TEM) and current–voltage ( I–V ) characteristic demonstrate that the lamella device shows a volatile RS behavior with a threshold switching at ≈ ± 0.4 V. In situ scanning transmission electron microscopy (STEM) experiments with electron energy loss spectroscopy (EELS) reveal that the charge carriers such as oxygen vacancies migrate under positive/negative DC bias and modulate Schottky barriers at the top and bottom metal/semiconductor interfaces. The RS mechanism of the lamella device is based on the Schottky barriers modulation and Joule heating assisted electric field triggered thermal runaway (FTTR) occurred at the metal/semiconductor interfaces. The fundamental insights gained from this study presents a perspective on interface‐type RS devices processing and opens up new technological opportunities of fabricating ultra‐low‐energy memristive devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Probing molecular vibrations by monochromated electron microscopy

Chemical bonds fundamentally determine molecular properties and are prevalently characterized by various spectroscopic means such as infrared and Raman spectroscopies. However, the spatial resolution of these conventional approaches is insufficient to reveal nanoscale features. Recently, monochromated electron energy-loss spectroscopy (EELS) in the transmission electron microscope achieved a groundbreaking energy resolution of a few millielectronvolts and enabled direct observation of molecular vibrational spectrum with unmatched spatial resolution. Vibrational EELS is widely applicable to both organic and inorganic matter in the solid state or liquid phase. In this study, we introduce recent advancements and key concepts of this method, compare with other spectroscopic techniques, and discuss future developments for potential applications in research fields centered on catalysts, polymers, and live cells.

Vibrational Spectroscopy↗
DOE OSTI2024

Mechanical and electrical changes in electrochemically active polyimide binders for Li-ion batteries

Polyimide binders are often used in electrodes made with silicon for lithium-ion batteries for their mechanical strength and adhesion, which help mitigate mechanical issues associated with large volumetric expansion. These binders can be electrochemically active, but it is difficult to characterize what physical and chemical changes occur due to a composite electrode with multiple components and processes at play. Here, in this work, we study electrodes consisting only of polyimide binder and conductive carbon, using scanning probe-based techniques—contact resonance, force volume, and scanning spreading resistance microscopy—along with cryo-scanning transmission electron microscopy, electron energy loss spectroscopy, and energy dispersive X-ray spectroscopy. We show that lithium becomes trapped in the binder during cycling and results in large initial capacity losses, the formation of dendrite-like features, column-like domains of significantly increased mechanical modulus, and a slight increase in electronic resistivity.

25 ENERGY STORAGE↗
DOE OSTI2026

Electron energy loss spectroscopy study of ceria sinters and nanoparticles irradiated with swift heavy ions

The electronic energy loss spectra of ceria (CeO 2 ) irradiated with swift heavy ions (27 MeV Xe and 946 MeV Au) in the electronic slowing down regime were measured for bulk sintered samples and nanoparticles by using a double Cs-corrected transmission electron microscope. The low-loss region as well as the core-loss region, including the oxygen K-edge and cerium M 4, 5 white lines, were recorded. No strong lattice disorder was found in the low-loss peaks for both types of samples showing the same bulk oxygen plasmon loss peak at about 15 eV. However, there is a clear evidence of cerium reduction to the trivalent oxidation state after irradiation for the sintered samples as shown by the K-edge shape of oxygen and decrease of the Ce M 4 /M 5 intensity ratio. A similar change of the M 4 /M 5 intensity ratio was observed for the irradiated nanoparticles with respect to the virgin sample owing to the high energy input inside the nanograin. The effect of radiation damage on electron energy loss spectroscopy data is analyzed for both types of samples and irradiation conditions.

Crystallographic defects↗
DOE OSTI2026

Mitigating Data Center Impact on Grid Stability: A Coordinated Control Strategy Using Verrus StabiliGrid Architecture

Large data centers, which now represent a significant and growing share of the total U.S. grid load, can inadvertently destabilize the electrical grid when they disconnect simultaneously during brief voltage disturbances. The July 10, 2024, Eastern Interconnection incident, in which a sub-100-millisecond transmission fault triggered the cascading loss of approximately 1,500 MW of data center load, illustrates this vulnerability. While commercial battery energy storage systems (BESS) deployed in data centers provide device-level fault ride-through per IEEE 1547, they lack coordination with facility protection logic and uninterruptible power supplies (UPS), limiting their effectiveness as grid-stabilizing assets. This report presents the Verrus StabiliGrid architecture, a coordinated control framework that integrates BESS, UPS, and point-of-interconnection (POI) protection settings to enable data centers to ride through both undervoltage and overvoltage grid contingencies without disconnecting. The four-step strategy encompasses: (1) high-resolution power quality monitoring to detect the grid state during events such as undervoltage, overvoltage, underfrequency, and overfrequency; (2) POI protection settings that allow for extended ride-through and grid-connected operation during grid contingencies; (3) grid state-driven autonomous dispatch of assets to improve grid resilience by reducing power draw during undervoltage or absorbing more power during overvoltage events; and (4) coordinated post-recovery dispatch of data center assets to restore firm load to pre-contingency levels. Validated through controller-hardware-in-the-loop (C-HIL) simulations at the National Laboratory of the Rockies, results show grid import restoration to pre-fault levels within 100 milliseconds of voltage recovery. This work advances the ability of data centers to transition from passive, disturbance-sensitive loads to active participants in grid stability, a capability increasingly required by emerging NERC and ERCOT regulatory frameworks.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Transmission risk of Oropouche fever across the Americas

Abstract Background Vector-borne diseases (VBDs) are important contributors to the global burden of infectious diseases due to their epidemic potential, which can result in significant population and economic impacts. Oropouche fever, caused by Oropouche virus (OROV), is an understudied zoonotic VBD febrile illness reported in Central and South America. The epidemic potential and areas of likely OROV spread remain unexplored, limiting capacities to improve epidemiological surveillance. Methods To better understand the capacity for spread of OROV, we developed spatial epidemiology models using human outbreaks as OROV transmission-locality data, coupled with high-resolution satellite-derived vegetation phenology. Data were integrated using hypervolume modeling to infer likely areas of OROV transmission and emergence across the Americas. Results Models based on one-support vector machine hypervolumes consistently predicted risk areas for OROV transmission across the tropics of Latin America despite the inclusion of different parameters such as different study areas and environmental predictors. Models estimate that up to 5 million people are at risk of exposure to OROV. Nevertheless, the limited epidemiological data available generates uncertainty in projections. For example, some outbreaks have occurred under climatic conditions outside those where most transmission events occur. The distribution models also revealed that landscape variation, expressed as vegetation loss, is linked to OROV outbreaks. Conclusions Hotspots of OROV transmission risk were detected along the tropics of South America. Vegetation loss might be a driver of Oropouche fever emergence. Modeling based on hypervolumes in spatial epidemiology might be considered an exploratory tool for analyzing data-limited emerging infectious diseases for which little understanding exists on their sylvatic cycles. OROV transmission risk maps can be used to improve surveillance, investigate OROV ecology and epidemiology, and inform early detection.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Formation of uranium nitride nanoparticles via mechanical alloying of uranium-molybdenum alloy fuels in gaseous nitrogen

Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and fuel loading capability. However, U-Mo systems are susceptible to irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interactions. To address these shortcomings, this research investigated the formation of uranium mononitride (UN) nanoparticles within a 90 wt% U/10 wt% Mo (U-10Mo) matrix to act as a prospective defect sink for fission products at nanometric hetero-interfaces. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen atmosphere. Variations of the milling process investigated included media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. Characterization of the fuel microstructure was completed using light element analysis, X-ray diffraction, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. UN nanoparticles measuring 1–5 nm in radius were observed in the U-Mo matrix as early as 1 h into the mechanical alloying process. Milling time in excess of 10 h was found to lead to deleterious effects induced by the stainless-steel milling media.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Impact of acetic acid exposure on metal contact degradation of different crystalline silicon solar cell technologies

Degradation due to acetic acid in photovoltaic (PV) modules has been a commonly observed phenomenon for both damp-heat exposure and outdoor operations. Acetic acid is a degradation byproduct of ethylene-vinyl acetate (EVA), a common module encapsulant. To address this issue, robust metallization pastes and cell technologies are being developed. However, it is important to assess how these technologies perform in an acetic acid environment and withstand degradation before they are implemented in the solar market. In this work, we investigate the impact of acetic acid exposure on four different cell groups: monofacial passivated emitter and rear contact (PERC) cells with advanced telluride-based front contact pastes, bifacial PERC cells with novel aluminum rear contact pastes, bifacial tunnel oxide passivated contacts (TOPCon) cells, and silicon heterojunction (SHJ) cells. These cells were exposed to acetic acid for different time increments. The recombination losses were characterized by Suns-VOC, and multi-variate regression analysis of intensity-dependent photoluminescence (PL) images with Griddler AI. Resistive losses were tracked with the transmission line method (TLM). Samples showing severe performance degradation were selected for further materials characterization to understand the root cause. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) were performed to investigate the change in materials properties. Our study shows that the front contacts of the bifacial TOPCon cells and monofacial PERC cells were significantly affected by acetic acid exposure. Here, the SHJ cells were found to be the most stable.

14 SOLAR ENERGY↗
DOE OSTI2021

Toward Decoding the Relationship between Domain Structure and Functionality in Ferroelectrics via Hidden Latent Variables

Polarization switching mechanisms in ferroelectric materials are fundamentally linked to local domain structure and the presence of the structural defects, which both can act as nucleation and pinning centers and create local electrostatic and mechanical depolarization fields affecting wall dynamics. However, the general correlative mechanisms between domain structure and polarization dynamics are only weakly explored, precluding insight into the associated physical mechanisms. In this work, the correlation between local domain structures and switching behavior in ferroelectric materials is explored using convolutional encoder–decoder networks, enabling image to spectral (im2spec) and spectral to image (spec2im) translations via encoding of latent variables. The latter reflect the assumption that the relationship between domain structure and polarization switching is parsimonious, i.e., is based upon a small number of local mechanisms. The analysis of latent variables distributions and their real-space representations provides insight into the predictability of the local switching behavior and hence associated physical mechanisms. We further pose that the regions where these correlative relationships are violated, i.e., predictability of the polarization dynamics from domain structure is reduced, represent the obvious target for detailed studies, e.g., in the context of automated experiments. This approach provides a workflow to establish the presence of correlation between local spectral responses and local structure and can be universally applied to spectral imaging techniques such as piezoresponse force microscopy (PFM), scanning tunneling microscopy (STM) and spectroscopy, and electron energy loss spectroscopy (EELS) in scanning transmission electron microscopy (STEM).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Magnetic and Optical Properties of Au–Co Solid Solution and Phase-Separated Thin Films and Nanoparticles

The chemical composition and morphology of Au x Co 1–x thin films and nanoparticles are controlled via a combination of cosputtering, pulsed laser-induced dewetting (PLiD), and annealing, leading to tunable magnetic and optical properties. Regardless of chemical composition, the as-deposited thin films and as-PLiD nanoparticles are found to possess a face-centered cubic (FCC) Au x Co 1–x solid-solution crystal structure. Annealing results in large phase-separated grains of Au and Co in both the thin films and nanostructures for all chemical compositions. The magnetic and optical properties are characterized via vibrating sample magnetometry (VSM), ellipsometry, optical transmission spectroscopy, and electron energy loss spectroscopy (EELS). Despite the exceptionally high magnetic anisotropy inherent to Co, the presence of sufficient Au (72 atom %) in the Au x Co 1–x solid solution results in superparamagnetic thin films. Among the as-PLiD nanoparticle samples, an increased Co composition leads to a departure from traditional ferromagnetism in favor of wasp-waisted hysteresis caused by magnetic vortices. Phase separation resulting from annealing leads to ferromagnetism for all compositions in both the thin films and nanoparticles. The optical properties of Au x Co 1–x nanostructures are also largely influenced by the chemical morphology, where the Au x Co 1–x intermixed solid solution has significantly damped plasmonic performance relative to pure Au and comparable to pure Co. Phase separation greatly enhances the quality factor, optical absorption, and electron energy loss spectroscopy (EELS) signatures. The enhancement of the localized surface plasmon resonances (LSPRs) scales with the reduction in Co composition, despite EELS evidence that excitation of the Co portions of a nanoparticle can provide a similar, and in some instances enhanced, LSPR resonance compared to Au. This behavior, however, is seemingly limited to the LSPR dipole mode, while higher-order modes are greatly damped by a Co aloof position. As a result, this observed magneto-plasmonic functionality and tunability could be applicable in biomedicine, namely, cancer therapeutics.

annealing (metallurgy)↗
DOE OSTI2023

Electrolyte Reactivity on the MgV 2 O 4 Cathode Surface

Predictive understanding of the solvation-dependent reactivity and molecular interaction of electrolyte ions and solvent molecules on reactive electrodes has been a major challenge but is essential for addressing instabilities and surface passivation that occur at electrode-electrolyte interface (EEI) of multivalent Mg batteries. In this work, the isolated intrinsic reactivities of prominent chemical species present in magnesium bis(trifluoromethanesulfonimide) (Mg(TFSI) 2 ) in diglyme (G2) electrolytes, including ionic (TFSI - , [Mg(TFSI)] + , [Mg(TFSI):G2] + , [Mg(TFSI):2G2] + ) as well as neutral molecules (G2) on magnesium vanadate cathode (MgV 2 O 4 ) surface has been studied using a combination of first-principles calculations and multimodal analysis of well-defined cathode electrolyte interphase (CEI) layers. Here, our calculations show that non-solvated [Mg(TFSI)] + is the strongest adsorbing species on the MgV 2 O 4 surface compared to all other ions while fully solvated [Mg(TFSI):2G2] + are least favorable to decomposition. The cleavage of C-S bonds in TFSI - to form CF 3 - is predicted to be most desired pathway for all ionic species, which is followed by the cleavage of C-O bonds of G2 to yield CH 3 + or OCH 3 - species. The strong stabilization and electron transfer between ionic electrolyte species and MgV 2 O 4 is found to significantly favor these decomposition reactions on the surface compared to intrinsic gas phase dissociation. Experimentally, we used state-of-the-art ion soft landing to selectively deposit mass-selected TFSI - , [Mg(TFSI):G2] + and [Mg(TFSI):2G2] + on MgV 2 O 4 thin film to form well-defined electrolyte-MgV 2 O 4 interface. Analysis of soft-landed interphase using X-ray photoelectron, X-ray absorption near edge structure, electron energy-loss spectroscopies as well as transmission electron microscopy confirmed the presence of decomposition species (e.g., MgFx, carbonates) formed in the interfacial region and the higher amount of MgFx with [Mg(TFSI):G2] + , which corroborates the theoretical observation. Overall, we established the mechanistic pathway for the electrolyte-induced formation of passivating fluorides on MgV 2 O 4 cathode facilitated by the surface adsorption and charge transfer, which provided essential knowledge for rational design of stable electrolytes for multivalent cathodes.

Cathode-electrolyte interphase formation↗