SEARCH · Search NASA
Results for “TURBINES - BLADES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Progress in Design of Novel Hybrid CMC Turbine Vanes for Advanced Turbines
Brief Recap of Hybrid ceramic/CMC materials at RTRC (UTRC) Development of concept for turbine airfoils Exploration of materials systems for armor Phase I DoE Project Goals Progress within the Phase I program
Erosion, Corrosion and Foreign Object Damage Effects in Gas Turbines [Les consequences de l'endommagement des turbines I gaz par erosion, corrosion et objets étrangers]
The Conference Proceedings contains 31 papers presented at the Propulsion and Energetics Panel Symposium on Erosion, Corrosion and Foreign Object Damage Effects in Gas Turbines which was held from 25-28th April 1994, in Rotterdam, The Netherlands. The Technical Evaluation Report and the Keynote Address are included at the beginning and discussions follow most papers. The Symposium was arranged in the following Sessions: Operational Experience and Requirements (7); Deposition and Erosion (7); Foreign Object Damage (5); Coatings, Repairs and Materials Aspects - 1 (4); Coatings, Repairs and Materials Aspects - 2 (7); and Testing and Certification Procedures (1).
Front-End Engineering Design (FEED) Study for a Carbon Capture Plant Retrofit to a Natural Gas-Fired Gas Turbine Combined Cycle Power Plant (2x2x1 Duct-Fired 758-MWe Facility with F Class Turbines)
A comprehensive front-end engineering design (FEED) study has been undertaken by Bechtel National Inc. (Bechtel) for locating a post-combustion capture and compression (PCC) unit at Panda’s Sherman natural gas–combined cycle (NGCC) power plant in Sherman, Texas. This is described in the unredacted FEED Study report (Attachment 1) with all supporting documents, numbering over 150. The Study Report is publicly available. Sizing of the PCC plant is based on treating an amount of flue gas equivalent to that produced when generating 420 MW, which is approximately 68% of the total flue gas emitted by the NGCC power plant operating at guarantee condition with duct burners off. A reduced power plant capacity factor was used for sizing the PCC plant because the gas turbines at the site often operate at reduced load due to the high penetration of renewable power in the ERCOT region. The cost of carbon capture is primarily driven by capital cost (and therefore is highly sensitive to capacity factor). Sizing the capture unit so that when used it is nearly always operating at full capacity is critical to the economic viability of the proposed investment.
An Intermediate-Scale Version of the Volturnus + Floating Offshore Wind Turbine Platform Concept in a Real Ocean Environment with an Operating Turbine off the Coast of Maine (Final Scientific/Technical Report)
This project was undertaken to advance the technical readiness and commercial viability of a next-generation, industrialized concrete floating foundation for offshore wind turbines called VolturnUS +. The design objective is to deliver a platform that is lower cost, faster to manufacture, simpler to deploy, and optimized for domestic supply chains and local workforce participation. To enable project financing and commercial adoption, an at-sea demonstration under representative operating conditions was required and therefore this project aimed to deploy a ¼-scale VolturnUS+ prototype offshore the Coast of Maine.
Effect of variable stator area on performance of a single-stage turbine suitable for air cooling. 3 - Turbine performance with 130-percent design stator area
Turbine performance with 130 percent design stator area
Effect of variable stator area on performance of a single-stage turbine suitable for air cooling. 6 - Turbine performance with 70-percent design stator area
Variable stator area effect on performance of single stage turbine suitable for air cooling
Turbine aerodynamic considerations for advanced turbines
Aerodynamic characteristics of advanced turbine engines
Erosion in radial inflow turbines. Volume 3: Trajectories of erosive particles in radial inflow turbines
The theoretical trajectories that erosive particles follow in the gas flow fields of a typical radial inflow turbine were investigated. A discussion of the theoretical trajectories that the particles follow in the scroll, in the nozzles, in the vortex between the nozzles and the rotor, and in the rotor passages is included. The results are presented in terms of the characteristic length, a similarity parameter which relates the particles that follow the same trajectory in equivalent flow fields. For Vol, 1, see N74-19395.
Cold-air performance of a tip turbine designed to drive a lift fan. 3: Effect of simulated fan leakage on turbine performance
Performance data were obtained experimentally for a 0.4 linear scale version of the LF460 lift fan turbine for a range of scroll inlet total to diffuser exit static pressure ratios at design equivalent speed with simulated fan leakage air. Tests were conducted for full and partial admission operation with three separate combinations of rotor inlet and rotor exit leakage air. Data were compared to the results obtained from previous investigations in which no leakage air was present. Results are presented in terms of mass flow, torque, and efficiency.
Effect of water injection and off scheduling of variable inlet guide vanes, gas generator speed and power turbine nozzle angle on the performance of an automotive gas turbine engine
The Chrysler/ERDA baseline automotive gas turbine engine was used to experimentally determine the power augmentation and emissions reductions achieved by the effect of variable compressor and power engine geometry, water injection downstream of the compressor, and increases in gas generator speed. Results were dependent on the mode of variable geometry utilization. Over 20 percent increase in power was accompanied by over 5 percent reduction in SFC. A fuel economy improvement of at least 6 percent was estimated for a vehicle with a 75 kW (100 hp) engine which could be augmented to 89 kW (120 hp) relative to an 89 Kw (120 hp) unaugmented engine.
Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 1: Volute-manifold and stator performance
The aerodynamic performance of the inlet manifold and stator assembly of the compressor drive turbine was experimentally determined with cold air as the working fluid. The investigation included measurements of mass flow and stator-exit fluid torque as well as radial surveys of total pressure and flow angle at the stator inlet and annulus surveys of total pressure and flow angle at the stator exit. The stator-exit aftermixed flow conditions and overall stator efficiency were obtained and compared with their design values and the experimental results from three other stators. In addition, an analysis was made to determine the constituent aerodynamic losses that made up the stator kinetic energy loss.
Investigation of Turbines Suitable for Use in a Turbojet Engine Wtih High Compressor Pressure Ratio and Low Compressor-tip Speed V : Experimental Performance of Two-stage Turbine with Downstream Stator
An experimental investigation of a highly loaded two-stage turbine with a downstream stator revealed that (1) at equivalent design work and speed the brake internal efficiency was 0.81 and the maximum efficiency obtained was 0.85, and (2) the downstream stator left very little energy in the form of tangential velocity in the gas and, in general, performed well with 0.78 recovery being obtained at equivalent design work and speed.
Fundamentals of the Control of Gas-Turbine Power Plants for Aircraft: Principles of Control Common to Jet, Turbine-Propeller Jet, and Ducted-Fan Jet Power Plants - Part 2
After defining the aims and requirements to be set for a control system of gas-turbine power plants for aircraft, the report will deal with devices that prevent the quantity of fuel supplied per unit of time from exceeding the value permissible at a given moment. The general principles of the actuation of the adjustable parts of the power plant are also discussed.
Grainex Mar-M 247 Turbine Disk Life Study for NASA's High Temperature High Speed Turbine Seal Test Facility
An experimental and analytical fatigue life study was performed on the Grainex Mar-M 247 disk used in NASA s Turbine Seal Test Facility. To preclude fatigue cracks from growing to critical size in the NASA disk bolt holes due to cyclic loading at severe test conditions, a retirement-for-cause methodology was adopted to detect and monitor cracks within the bolt holes using eddy-current inspection. For the NASA disk material that was tested, the fatigue strain-life to crack initiation at a total strain of 0.5 percent, a minimum to maximum strain ratio of 0, and a bolt hole temperature of 649 C was calculated to be 665 cycles using -99.95 percent prediction intervals. The fatigue crack propagation life was calculated to be 367 cycles after implementing a safety factor of 2 on life. Thus, the NASA disk bolt hole total life or retirement life was determined to be 1032 cycles at a crack depth of 0.501 mm. An initial NASA disk bolt hole inspection at 665 cycles is suggested with 50 cycle inspection intervals thereafter to monitor fatigue crack growth.
Component Performance Investigation of J71 Type II Turbines V - Internal Flow Conditions of J71 Type IIA Turbine
An experimental investigation of the J71 Type IIA turbine was conducted at the equivalent design speed and work output. The design stagework distribution was closely approached, although the design vector diagram was not attained. Efficiencies of 0.904, 0.851, and 0.806 were obtained for the first, second, and third stages, respectively. Losses occurred near the hub and tip for all three rotors. The third-stage losses, however, were significantly greater than those of either the first or second stage.
The performance of a composite engine consisting of a reciprocating spark-ignition engine, a blow-down turbine, and a steady-flow turbine
Explore the source record for details and available documents.
Aero-structural rapid screening of new design concepts for offshore wind turbines
Not provided.