Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thrust Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Evaluation of drilled-ball bearings at DN values to three million. 1: Variable oil flow tests

Two 125-mm-bore solid ball bearings and two similar drilled ball bearings were operated at speeds up to 24,000 rpm (3.0 million DN) with a 13,000 newton (3000 lb) thrust load. The oil flow rate was varied from 0.045 to 0.121 kilograms per second (6 to 16 lb/min). The solid ball bearings operated satisfactorily over the entire range of conditions. The drilled ball bearing experienced cage rub with marginal lubrication at 0.045 kilograms per second (6 lb/min). The drilled ball bearing generally ran cooler than the solid ball bearings.

Holmes, P. W.↗

Evaluation of drilled-ball bearings at DN values to three million. 2: Experimental skid study and endurance tests

Both drilled-and solid-ball 120-mm-bore bearings were tested at speeds up to 24,000 rpm to determine skid characteristics. The thrust loads were varied from 5000 lb down to 370 lb. No gross skidding occurred, and the behavior of the two bearing types was generally similar; however, two drilled-ball bearing failures occurred during the skid tests. In the endurance tests, 25 cycles of start, run (for one hour), and stop were completed before a drilled-ball bearing failed. In all three cases, the ball had failed in flexure fatigue.

Holmes, P. W.↗

Optimal speed sharing characteristics of a series-hybrid bearing

A series-hybrid bearing assembly consisting of a conical hydrostatic fluid-film bearing and a ball bearing is described. Computer studies are used to predict friction torque and life characteristics of a 150-millimeter ball bearing. A conical hydrostatic fluid-film bearing is designed for minimum friction and maximum speed reduction of the ball-bearing component of the series-hydrid bearing. At a thrust load of 4000 pounds and speeds corresponding to DN (bearing bore in millimeters times shaft speed in rpm) values of 3 and 4 million, ball-bearing speed may be reduced by 30 percent. This speed reduction corresponds to ball-bearing fatigue life improvement factors of 3.4 at 3 million DN and 5.9 at 4 million DN. An oil flow rate of 18.2 pounds per minute is required to maintain a fluid-film thickness of 0.001 inch in the hydrostatic bearing.

Nypan, L. J.↗

The series hybrid bearing - A new high speed bearing concept.

The series-hybrid bearing couples a fluid-film bearing with a rolling-element bearing such that the rolling-element bearing inner race runs at a fraction of shaft speed. A series-hybrid bearing was analyzed and experiments were run at thrust loads from 100 to 300 lb and speeds from 4000 to 30,000 rpm. Agreement between theoretical and experimental speed sharing was good. The lowest speed ratio (ratio of ball bearing inner-race speed to shaft speed) obtained was 0.67. This corresponds to an approximate reduction in DN value of 1/3. For a ball bearing in a 3 million DN application, fatigue life would theoretically be improved by a factor as great as 8.

Anderson, W. J.↗

A prediction model for lift-fan simulator performance

The performance characteristics of a model VTOL lift-fan simulator installed in a two-dimensional wing are presented. The lift-fan simulator consisted of a 15-inch diameter fan driven by a turbine contained in the fan hub. The performance of the lift-fan simulator was measured in two ways: (1) the calculated momentum thrust of the fan and turbine (total thrust loading), and (2) the axial-force measured on a load cell force balance (axial-force loading). Tests were conducted over a wide range of crossflow velocities, corrected tip speeds, and wing angle of attack. A prediction modeling technique was developed to help in analyzing the performance characteristics of lift-fan simulators. A multiple linear regression analysis technique is presented which calculates prediction model equations for the dependent variables.

Yuska, J. A.↗

Performance of 40-millimeter-bore ball bearings with lead- and lead-alloy-plated retainers in liquid hydrogen at 1.2 million DN

Forty-millimeter-bore ball bearings with lead- and lead-alloy-coated retainers were operated in liquid hydrogen at 30,000 rpm under a thrust load of 1780 N (400 lb.) Four different substrate materials were used for the retainer. Longer bearing run times were achieved with a lead-tin-copper alloy coating plated onto a leaded-bronze material (22.5 hr) and an aluminum-bronze alloy (19.3 hr). One bearing with a pure lead coating achieved the desired objective of 10 hr. This bearing had an aluminum - bronze substrate retainer and ran successfully for 12.4 hr. Additions of antimony to the lead provided an alloy coating with better wear resistance than pure lead; however, this coating was abrasive to the outer-race lands.

Brewe, D. E.↗

Performance of high speed ball bearings with lead and lead alloy plated retainers in liquid hydrogen at 1.2 million DN

Ball bearings with lead- and lead-alloy-coated retainers were operated in liquid hydrogen at 30,000 rpm under a thrust load of 400 lb. Bearing lives were compared using different: (1) lead- and lead-alloy coatings, (2) coating thicknesses, (3) substrate materials, (4) retainer locating surfaces, and (5) plating techniques. Longer bearing run times were achieved using retainers with a lead-tin-copper alloy coating electroplated onto a leaded-bronze material and an aluminum-bronze alloy. Thirty percent of the bearings tested achieved the desired objective of 10 hours. All of the lead-alloy coated retainers exceeded this objective. A coating thickness of at least 0.0014 in. was used for all bearings exceeding the 10-hour goal.

Brewe, D. E.↗

Ball motion and sliding friction in an arched outer race ball bearing

The motion of the ball and sliding friction in an arched outer race ball bearing under thrust loads is determined. Fatigue life evaluations were made. The analysis is applied to a 150 millimeter bore ball bearing. The results indicated that for high speed-light load applications the arched bearing has significant improvement in fatigue life over that of a conventional bearing. An arching of 0.254 mm (0.01 in.) was found to be an optimal. For an arched bearing it was also found that a considerable amount of spinning occurs at the outer race contacts.

Hamrock, B. J.↗

Analysis of an arched outer-race ball bearing considering centrifugal forces.

Thrust-load analysis of a 150-mm angular contact ball bearing, taking into account centrifugal forces but omitting gyroscopics, elastohydrodynamics, and thermal effects. A Newton-Raphson method of iteration is used to evaluate the radial and axial projection of the distance between the ball center and the outer raceway groove curvature center. Fatigue life of the bearing is evaluated. Results for life, contact loads, and angles are given for a conventional bearing and two arched bearings.

Hamrock, B. J.↗

Optimal speed sharing characteristics of a series-hybrid bearing.

A series-hybrid bearing assembly consisting of a conical hydrostatic fluid-film bearing and a ball bearing is described. Computer studies are used to predict friction torque and life characteristics of a 150-mm ball bearing. A conical hydrostatic fluid-film bearing is designed for minimum friction and maximum speed reduction of the ball-bearing component of the series-hybrid bearing. At a thrust load of 4000 lb and speeds corresponding to DN (bearing bore in millimeters times shaft speed in rpm) values of 3 and 4 million, ball-bearing speed may be reduced to 30%. This speed reduction corresponds to ball-bearing fatigue life improvement factors of 3.4 at 3 million DN and 5.9 at 4 million DN. An oil flow rate at 18.2 lb/min is required to maintain a fluid-film thickness of 0.001 in. in the hydrostatic bearing.

Nypan, L. J.↗

High temperature lubricant screening and systems studies

Four candidate lubricants for next generation aircraft gas turbine application were tested under open atmosphere conditions in a rig simulating an advanced engine 125 mm bore mainshaft thrust bearing position. Testing was conducted at speeds to 24,000 rpm (3,000,000 bearing DN), bearing ring temperature of 500 F, and with 1200 F air and 100 psi differential pressure across the seals installed in a dual tandem arrangement. Test bearing was a 125 mm bore split inner ring, outer race riding angular contact ball bearing under a 3280 lb. thrust load. One lubricant, a type 2 ester, performed extremely well. The mainshaft seal limited the performance. Numerous design improvements for this seal were indicated.

Jones, D. A.↗

Ball motion and sliding friction in an arched outer-race ball bearing

The motion of the ball and sliding friction in an arched outer-race ball bearing under thrust load is analyzed. Fatigue life evaluations were made. The analysis is applied to a 150-millimeter-bore ball bearing. The results indicated that for high-speed light-load applications the arched bearing has significant improvement in fatigue life over that of a conventional bearing. An arching of 0.254 mm (0.01 in.) was found to be optimal. Also, for an arched bearing a considerable amount of spinning occurs at the outer-race contacts.

Hamrock, B. J.↗

Design integration and noise studies for jet STOL aircraft. Task 7C: Augmentor wing cruise blowing valveless system. Volume 2: Small-scale development testing of augmentor wing critical ducting components

Augmentor wing ducting system studies conducted on a valveless system configuration that provides cruise thrust from the augmentor nozzles have shown that most of the duct system pressure loss would occur in the strut-wing duct y-junction and the wing duct-augmentor lobe nozzles. These components were selected for development testing over a range of duct Mach numbers and pressure ratios to provide a technical basis for predicting installed wing thrust loading and for evaluating design wing loading of a particular wing aspect ratios. The flow characteristics of ducting components with relatively high pressure loss coefficients were investigated. The turbulent pressure fluctuations associated with flows at high Mach numbers were analyzed to evaluate potential duct fatigue problems.

Runnels, J. N.↗

Experimental ball bearing dynamics study

A photographic method was employed to record the kinematic performance of rolling elements in turbo machinery ball bearings. The 110 mm split inner ring test bearings had nominal contact angles of 26 deg and 34 deg. High speed films were taken at inner ring speeds of 4,000, 8,000 and 12,000 rpm and at thrust loads of 4,448 N and 22,240 N (1,000 and 5,000 lbs). The films were measured and this data reduced to obtain separator speed, ball speed and ball spin axis orientation.

Signer, H. R.↗

Design and fabrication of prototype system for early warning of impending bearing failure

A test program was conducted with the objective of developing a method and equipment for on-line monitoring of installed ball bearings to detect deterioration or impending failure of the bearings. The program was directed at the spin-axis bearings of a control moment gyro. The bearings were tested at speeds of 6000 and 8000 rpm, thrust loads from 50 to 1000 pounds, with a wide range of lubrication conditions, with and without a simulated fatigue spall implanted in the inner race ball track. It was concluded that a bearing monitor system based on detection and analysis of modulations of a fault indicating bearing resonance frequency can provide a low threshold of sensitivity.

Meacher, J.↗

Start-stop testing of two self-acting air-lubricated spiral groove thrust bearing coatings

Start-stop tests were conducted on air-lubricated spiral-groove thrust bearings. Application of a matrix-bonded molybdenum disulfide (MoS2) coating over a porous chrome oxide coating resulted in significantly lower friction, compared to bearings coated with chrome oxide only. The MoS2 coated bearing sustained 15,000 start-stop cycles at a maximum of 3600 rpm. Each cycle was 15 seconds on, 30 seconds off. The chrome oxide coated bearing failed by local welding after 2030 cycles. Both types of coatings exhibited early failures under higher thrust loads when operating films were insufficient to sustain the load without overheating.

Dunfee, J. D.↗

A study of forced flow separation in rocket nozzle

The characteristics of flow profile in a rocket nozzle during the start transient were investigated as well as possibilities of reducing the side-load thrust by sticking trip wires in the nozzle. To simplify the geometry of flow configuration around the trip wire, it was assumed that the flow is passing through square steps instead of round wires. Since a purely analytic solution is not available, a series of semiempirical solutions was proposed.

Chiou, J. N.↗

Performance of 75-millimeter-bore bearings using electron-beam-welded hollow balls with a diameter ratio of 1.26

An experimental investigation was performed to determine the rolling element fatigue life of electron beam-welded hollow balls with a diameter ratio (o.d./i.d.) of 1.26 and to determine the operating characteristics of bearings using these hollow balls. Similar bearings with solid balls were also tested and the data compared. The bearings were operated at shaft speeds up to 28,000 rpm with a thrust load of 2200 N (500 lb). Ball failures during the bearing tests were due to flexure fatigue. The solid and hollow ball bearings tested showed little difference in outer race temperatures and indicated the same bearing torque. The 17.5-mm (0.6875-in.) diameter balls were also tested in the five-ball fatigue tester and showed no significant difference in life when compared with the life of a solid ball.

Coe, H. H.↗