Search NASA⌕ Search

SEARCH · Search NASA

Results for “Time Constant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Analysis of the interaction of a laser pulse with a silicon wafer - Determination of bulk lifetime and surface recombination velocity

The decay of excess minority carriers produced in a silicon wafer of thickness d by a laser pulse is analyzed. A comprehensive theory based on this analysis is presented for the determination of bulk lifetime Tau(b) and surface recombination velocity S. It is shown that, starting with an exponential spatial profile, the carrier profile assumes a spatially symmetrical form after approximately one time constant of the fundamental mode of decay. Expressions for the spatial average of the carrier density as a function of time are derived for three temporal laser pulse shapes: impulse, square, and Gaussian. Particular attention is paid to the time constants of the fundamental and higher modes of decay. The ratios of the time constants of the higher modes to the fundamental mode, as well as the time constant of the fundamental mode, are presented over wide ranges of values of S and d. For Sd less than about 40 sq cm/s, a two-wafer method is developed to determine Tau(b) and S; it is also shown that the requirement of d/Tau(b) greater than about 20S is sufficient to adequately guarantee that the asymptotic value of the instantaneous observed lifetime differs from the bulk lifetime by no more than 10 percent.

Luke, Keung L.↗

Polarization characterization of PZT disks and of embedded PZT plates by thermal wave methods

In this work, the thermal wave method was applied to characterize PZT disks and embedded PZT plates with regard to the polarization magnitude and spatial homogeneity. The samples were exposed to periodic heating by means of a laser beam and the pyroelectric response was determined. Thermal relaxation times (single time constants or distributions of time constants) describe the heat losses of the PZT samples to the environment. The resulting pyroelectric current spectrum was fitted to the superposition of thermal relaxation processes. The pyroelectric coefficient gives insight in the polarization distribution. For PZT disks, the polarization distribution in the surface region showed a characteristic decrease towards the electrodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modeling the Effect of Evaporative Flux and Colloidal Aggregation on Crud Deposition

During the last few years lot of research has been conducted to investigate and predict the Crud deposition in PWRs. One of the common findings of various experimental and computational studies is that thickness or amount of crud deposits is directly related to evaporative flux maps. Evaporation driven deposition profile on the surfaces takes different forms, i.e. from ring to disk shapes during initial stages and in the form of porous to impervious continuous layers covering the hot fuel surface at the later stages. The amount and thickness of these deposits although are directly related to evaporative flux, the relationship is much complex and can be dependent upon several other factors. A popular problem relating evaporative flux to particulate deposition has been well studied in the form of drying of sessile colloidal drops. It was proposed that, this phenomenon is due to a geometrical constraint: the free surface, constrained by a pinned contact line squeezes the fluid outwards to compensate for evaporative losses and thereby transporting particles to the contact line. Later on a quantitative relationship between evaporative flux and deposition rate was proposed and validated by the same group, which showed power-law relationship. Deposition studies conducted with controlled concentration of particles with subcooled nucleate boiling also showed a power-law relationship rather than a simpler linear relationship whereas physics of evaporation would tend to concentrate particles at linear rate. In a typical subcooled nucleate boiling system, bubble growth and departure time is of the order 1-2 ms, measured experimentally. Diffusion time constant for dilute spherical metallic colloids such as crud particulates, generally present as particulate in process piping, range from 0.0025-2.5 sec in water for a size range 0.1-1.0 μm. Colloidal behavioral characteristics during the growth of bubbles can be computed with escape time constant at collision, which is dependent on effective Hamaker constant. For minimum effective Hamaker constant of Hematite is -2.5 kT and diffusion time constant τ = 0.0025 sec, escape time constant is computed as Kramer rule, τexp[A/kT] magnitude is 0.03 sec or 30 ms. This clearly indicates that evaporation will cause particles to come together and they cannot escape at a fast enough rate which would lead them to form agglomerates. Therefore both effects of evaporative flux in conjunction with the agglomeration kinetics must be considered for modeling the crud deposition if the evaporative flux is known. In this paper, we propose a phenomenological model of colloidal transport and aggregation with evaporative flux. The dynamic of particles interactions while drying of sessile colloidal drops is developed by coupling general transport equation with Smoluchowshki Coagulation equation. Crud deposition on the nuclear fuel has been a serious problem with severe consequences in nuclear power plants. In several studies it has been consistently reported that crud deposition is directly related to evaporative flux on the nuclear fuel surfaces. However, it has not been established how to quantify the deposition rates of crud type particulates if the evaporative flux is known. This complex multiphysics problem is similar to coffee-ring effect, where the governing physics is understood more clearly. In this work, a simplified geometry is used to model the effects of evaporative flux acting at a boundary on the colloidal concentration. The effect of this condition on change in concentration is shown numerically. Further, agglomeration is suspected to play a significant role in high evaporative flux such as bubble nucleation. The coagulation kinetics is modeled using uniform particle distribution and the effective total concentration of colloids including original particles and agglomerates is studied. Once this model is validated with a simple separate effect experiments, it can be integrated to large scale PWR models of evaluating evaporative flux and chemistry models developed by Electrical Power Research Institute (EPRI). (authors)

42 ENGINEERING↗

Ultrasensitive Superconducting Transition Edge Sensors Based On Electron-Phonon Decoupling

We have successfully fabricated the superconducting transition edge sensor (TES), bolometer technology that centers on the use of electron-phonon decoupling (EPD) to thermally isolate the bolometer. Along with material characterization for large format antenna coupled bolometer arrays, we present the initial test results of bolometer based on EPD designed for THz detection. We have selected a design approach that separates the two functions of photon absorption and temperature measurement, allowing separate optimization of the performance of each element. We have integrated Molybdenum/Gold (Mo/Au) bilayer TES and ion assisted thermally evaporated (IAE) Bismuth (Bi) films as radiation absorber coupled to a low-loss microstripline from Niobium (Nb) ground plane to a twin-slot antenna structure. The thermal conductance and the time constant of these devices have been measured, and are consistent with our calculations. The device exhibits a single time constant at 0.1 K of approx.160 IlS, which is compatible with readout by a high-bandwidth single SQUID or a time domain SQUID multiplexer. The effects of thermal conductance and electrothermal feedback are major determinants of the time constant, but the electronic heat capacity also plays a major role. The NEP achieved in the device described above is 2.5x10(exp -17)W(gamma)Hz. Our plan is to demonstrate a reduction of the volume in the superconducting element to 5 microns x 5 microns in films of half the thickness at Tc = 60mK. By calculation, this new geometry corresponds to an NEP reduction of two orders of magnitude to 2.5x10(exp -19)W/(gamma)Hz, with a time constant of ~130/ls.

Jethava, Nikhil↗

On the vertical thermal structure of Io's atmosphere

A radiative-thermal conduction model for the vertical thermal structure of Io's atmosphere is developed with solar heating by SO2 absorption in UV and near-IR bands and non-local thermodynamic equilibrium (LTE) cooling by SO2 nu(sub 1), nu(sub 2), nu(sub 3), vibrational bands and rotational lines. The model predicts the existence of a mesopause in Io's atmosphere when the surface pressure exceeds approximately 10 nbar. The radiative time constant for establishing a mesosphere/mesopause on Io is only approximately 20 min, whereas the thermospheric radiative time constant is about 1 hr. These time constants are significantly shorter than the diurnal time scale and competitive with dynamic time scales. In the thermosphere when solar UV heating dominates, the asymptotic thermospheric temperature is approximately 270 K, only 140 K greater than the surface temperature because at high altiudes non-LTE cooling by SO2 rotation lines exceeds cooling in the nu(sub 2) virbrational band. Solar-heating-only modles are incapable of generating warm enough atmospheres to satisfy the observational inferences from UV and especially millimeter-wave meausrements. Joule heating driven by the penetration of Jupiter's corotational electric field into Io's conducting ionosphere is demonstrated to be the dominant heating mechanism in the subnanobar regions of Io's atmosphere with tempertures ranging from 150 to 1000 K as a function of decreasing pressure from 1 to 0.1 nbar, The asymoptotic thermospheric temperature can attain a value as high as 1800 K.

Strobel, Darrell F.↗

Human Tracking Performance in Uncoupled and Coupled Two-Axis Systems

This report presents tile results of an experimental and analytical study of human performance in uncoupled and coupled control systems. Human pilot performance in single and two-axis systems was mathematically modeled by linear second-order describing functions. Model parameters were determined using model matching techniques. Analysis of the models showed that the amplitude ratio and phase lead of the describing function increased with training indicating an increase in open loop bandwidth. The phase margin also decreased with training. Increasing the plant lag time constant resulted in an increase in the model lead time constant and a decrease in the zero frequency gain. No significant difference was found to exist in the normalized tracking error per axis between the two-axis tasks and the single-axis tasks. However tile model lead time constant was significantly greater in two-axis tracking. Manual tracking of two-axis systems with cross-coupling was studied experimentally and analytically. Approximate methods for modeling two-axis performance were developed and checked using a precise spectral analysis approach. Coupled and uncoupled, symmetrical and asymmetrical two-axis performance was compared. The results show that modeling of cross-coupled systems is feasible and that trained subjects are capable of decoupling the axes of some systems. A methodology study compared the identification performance of continuous, iterative, and extrapolation model matching techniques. An iterative technique employing sensitivity equations for the generation of influence coefficients was found to be the best technique due to its excellent identification accuracy and ease of implementation. Convergence in iterative techniques can be improved substantially by equalizing the parameter adjustment rates and limiting the maximum correction per iteration.

Todosiev, E. P.↗

Delay decomposition at a single server queue with constant service time and multiple inputs

Two network consisting of single server queues, each with a constant service time, are considered. The external inputs to each network are assumed to follow some general probability distribution. Several interesting equivalencies that exist between the two networks considered are derived. This leads to the introduction of an important concept in delay decomposition. It is shown that the waiting time experienced by a customer can be decomposed into two basic components called self-delay and interference delay.

Ziegler, C.↗

Delay decomposition at a single server queue with constant service time and multiple inputs

Two networks consisting of single server queues, each with a constant service time, are considered. The external inputs to each network are assumed to follow some general probability distribution. Several interesting equivalencies that exist between the two networks considered are derived. This leads to the introduction of an important concept in delay decomposition. It is shown that the waiting time experienced by a customer can be decomposed into two basic components called self delay and interference delay.

Ziegler, C.↗

Enhanced Frequency Support Scheme of Generic Inverter-Based Resource Models for Renewable-Dominated Power Grids

The frequency response of SG-dominated power grids is predictable ahead of an occurrence of a frequency event because the frequency response of SGs is consistent, and it can be inferred from the swing equation [1]. However, increasing the portion of IBRs in an SG-dominated power grid might make the characteristics of the conventional power grids no longer valid because this changing resource mix affects grid dynamics and controls [2]. Thus, maintaining these characteristics greatly benefits the control and operation of the power grids with high penetration of IBRs. To maintain these characteristics in IBR-dominated power grids, IBRs should have frequency response capability similar to that of an SG. The WECC modeling validation subcommittee has developed generic IBR models for large system planning [3]-[5]. These models can represent various vendors' dynamic behavior for WTG, PV, and ESS [5]. The current generic IBR models approved by WECC can provide frequency response only from droop control loops in REPC models [6], [7]. The contribution of the loops is proportional to the frequency deviation from the nominal frequency. Thus, it presents an insufficient contribution to arrest frequency variation compared to the frequency response of SGs because it allows a high ROCOF in the early stage of frequency events. This shortfall will become greater as the PL of IBRs increases in power grids. Controller enhancement for the generic IBR models is required to secure the frequency stability under high PL of IBRs as in the SG-dominated power grids. This paper proposes a control extension for the generic IBR models to enhance the frequency support capabilities and discusses the classification of frequency support for the different types of IBR considering their operating constraints. An inertial control scheme is implemented in the REPC and REEC models of the generic IBR models to achieve these objectives. The inertial control scheme includes the following stages: Control area data acquisition, inertia time constant estimation, IBR-related constraint check, IBR contribution determination, and inertial response provision. In the scheme, a REPC acquires control area data from a system operator and estimates a total inertia time constant for the control area the applicable IBR power plant belongs. Then, the estimated inertial time constant is transferred to each IBR controller—REEC—within the power plant. Each REEC checks the availability of applicable IBR for inertial response participation. If the IBR is available, the REEC amplifies the estimated inertial time constant to utilize it for inertial response provision. In this way, the proposed inertial response scheme extends the functionality of the generic IBR models to provide SG-like frequency response within their constraints. Various scenarios considering different IBR types, IBR penetration levels, and frequency control schemes were simulated and compared in an IEEE 39-bus system using PSCAD simulator to verify the effectiveness of the proposed scheme.

Kim, Jinho↗

Linking stem rehydration kinetics to hydraulic traits using a novel method and mechanistic model

Background: Despite the recognized importance of hydraulic capacitance as a mechanism used by plants to maintain hydraulic functioning during high transpiration, characterizing the dynamics of capacitance remains a challenge. Methods: For this work, we used a novel ‘two-balance method’ to investigate relationships between stem rehydration kinetics and other hydraulic traits in multiple tree species, and we developed a model to explore stem rehydration kinetics further. Key Results: We found that: (1) rehydration time constants and the amount of water uptake occurring during rehydration differed significantly across species; (2) time constants did not change with declining water potential (Ψ), while water uptake increased at lower Ψ in some species; (3) longer time constants were associated with lower wood density, higher capacitance and less negative stem pressures causing 50 % loss of hydraulic conductivity (P 50 ); (4) greater water uptake occurred in stems with lower wood density and less negative P 50 values; and (5) the model could estimate the total hydraulic resistance of the rehydration path, which cannot be measured directly. Conclusions: Overall, the two-balance method can be used to examine rehydration dynamics quickly and thoroughly in detached woody stems. This method has the potential to improve our understanding of how capacitance functions across tree species, which is an often-overlooked component of whole-plant hydraulics.

54 ENVIRONMENTAL SCIENCES↗

Prompt Neutron Time Decay in Single HEU and DU Metal Annular Storage Castings

Previous measurements of highly enriched uranium (HEU) storage castings performed by Oak Ridge National Laboratory (ORNL) at the Y-12 National Security Complex showed a prompt neutron time decay that is not exponential. These measurements showed that multiple time constants originating from multiplication, time-of-flight, scattering in the assembly and room return could be associated with this prompt neutron decay. In this work, the contribution not associated with neutron multiplication was investigated via measurements with a depleted uranium (DU) casting. The measurements at ORNL used an annular (5.0-in OD, 3.5-in ID, 6.0-in H) DU casting with a time-tagged 252Cf source, centered vertically on the axis, and four closely coupled 1 1 6-in.-long plastic scintillators with -in.- thick lead shielding adjacent to the outer surface of the casting. This setup was identical to the configuration used in the previously performed measurements with HEU castings at Y-12. The time correlation between fission events and detections in the plastic scintillators was measured, as well as the time distribution of coincidences between multiple detectors within a 512-ns time window. The measurement results were then compared to MCNP-PoliMi calculations and the previous HEU measurements. Time constants from decay fits to the HEU and DU data were compared to characterize the contributions resulting from multiplication, time-of-flight, and scattering.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Shuttle program: Ground tracking data program document shuttle OFT launch/landing

The equations for processing ground tracking data during a space shuttle ascent or entry, or any nonfree flight phase of a shuttle mission are given. The resulting computer program processes data from up to three stations simultaneously: C-band station number 1; C-band station number 2; and an S-band station. The C-band data consists of range, azimuth, and elevation angle measurements. The S-band data consists of range, two angles, and integrated Doppler data in the form of cycle counts. A nineteen element state vector is used in Kalman filter to process the measurements. The acceleration components of the shuttle are taken to be independent exponentially-correlated random variables. Nine elements of the state vector are the measurement bias errors associated with range and two angles for each tracking station. The biases are all modeled as exponentially-correlated random variables with a typical time constant of 108 seconds. All time constants are taken to be the same for all nine state variables. This simplifies the logic in propagating the state error covariance matrix ahead in time.

Lear, W. M.↗

A new technique to study transient conductivity under pulsed monochromatic light in Cr-doped GaAs using acoustoelectric voltage measurement

The transient conductivity of high-resistivity Bridgman-grown Cr-doped GaAs under pulsed monochromatic light is monitored using transverse acoustoelectric voltage (TAV) at 83 K. Keeping the photon flux constant, the height and transient time constant at the TAV are used to calculate the energy dependence of the trap density and its cross section, respectively. Two prominent trap profiles with peak trap densities of approximately 10 to the 17th/cu cm eV near the valence and the conduction bands are detected. These traps have very small capture cross sections in the range of 10 to the -23 to 10 to the -21st cm sq. A phenomenon similar to the persistent photoconductivity with transient time constants in excess of a few seconds in high-resistivity GaAs at T = 83 K is also detected using this technique. These long relaxation times are readily explained by the spatial separation of the photo-excited electron-hole pairs and the small capture cross section and large density of trap distribution near the conduction band.

Tabib-Azar, Massood↗

Solution Phase Exciton Diffusion Dynamics of a Charge-Transfer Copolymer PTB7 and a Homopolymer P3HT

Using ultrafast polarization-controlled transient absorption (TA) measurements, dynamics of the initial exciton states were investigated on the time scale of tens of femtoseconds to about 80 ps in two different types of conjugated polymers extensively used in active layers of organic photovoltaic devices. These polymers are poly(3-fluorothienothiophenebenzodithiophene) (PTB7) and poly-3-hexylthiophene (P3HT), which are charge-transfer polymers and homopolymers, respectively. In PTB7, the initial excitons with excess vibrational energy display two observable ultrafast time constants, corresponding to coherent exciton diffusion before the vibrational relaxation, and followed by incoherent exciton diffusion processes to a neighboring local state after the vibrational relaxation. In contrast, P3HT shows only one exciton diffusion or conformational motion time constant of 34 ps, even though its exciton decay kinetics are multiexponential. Based on the experimental results, an exciton dynamics mechanism is conceived taking into account the excitation energy and structural dependence in coherent and incoherent exciton diffusion processes, as well as other possible deactivation processes including the formation of the pseudo-charge-transfer and charge separate states, as well as interchain exciton hopping or coherent diffusion.

36 MATERIALS SCIENCE↗

Electronic relaxation dynamics in [Au 25 (SR) 18 ] -1 (R = CH 3 , C 2 H 5 , C 3 H 7 , MPA, PET) thiolate-protected nanoclusters

Here we investigate the excited electron dynamics in [Au 25 (SR) 18 ] -1 (R = CH3, C 2 H 5 , C 3 H 7 , MPA, PET) [MPA = mercaptopropanoic acid, PET = phenylethylthiol] nanoparticles to understand how different ligands affect the excited state dynamics in this system. The population dynamics of the core and higher excited states lying in the energy range 0.00–2.20 eV are studied using a surface hopping method with decoherence correction in a real-time DFT approach. All of the ligated clusters follow a similar trend in decay for the core states (S 1 –S 6 ). The observed time constants are on the picosecond time scale (2–19 ps), which agrees with the experimental time scale, and this study confirms that the time constants observed experimentally could originate from core-to-core transitions and not from core-to-semiring transitions. In the presence of higher excited states, R = H, CH 3 , C 2 H 5 , C 3 H 7 , and PET demonstrate similar relaxations trends whereas R = MPA shows slightly different relaxation of the core states due to a smaller gap between the LUMO+1 and LUMO+2 gap in its electronic structure. The S 1 (HOMO → LUMO) state gives the slowest decay in all ligated clusters, while S 7 has a relatively long decay. Furthermore, separate electron and hole relaxations were performed on the [Au 25 (SCH 3 ) 18 ] -1 nanocluster to understand how independent electron and hole relaxations contribute to the overall relaxation dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantitative understanding of Forbush decrease drivers based on shock-only and CME-only models using global signature of February 14, 1978 event

We have studied the Forbush decrease (FD) event that occurred on February 14, 1978 using 43 neutron monitor observatories to understand the global signature of FD. We have studied rigidity dependence of shock amplitude and total FD amplitude. We have found almost the same power law index for both shock phase amplitude and total FD amplitude. Local time variation of shock phase amplitude and maximum depression time of FD have been investigated which indicate possible effect of shock/CME orientation. We have analyzed rigidity dependence of time constants of two phase recovery. Time constants of slow component of recovery phase show rigidity dependence and imply possible effect of diffusion. Solar wind speed was observed to be well correlated with slow component of FD recovery phase. This indicates solar wind speed as possible driver of recovery phase. To investigate the contribution of interplanetary drivers, shock and CME in FD, we have used shock-only and CME-only models. We have applied these models separately to shock phase and main phase amplitudes respectively. This confirms presently accepted physical scenario that the first step of FD is due to propagating shock barrier and second step is due to flux rope of CME/magnetic cloud.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optical Spectroscopy Approach for the Predictive Assessment of Kidney Functional Recovery Following Ischemic Injury

Tissue that has undergone significant yet unknown amount of ischemic injury is frequently encountered in organ transplantation and trauma clinics. With no reliable real-time method of assessing the degree of injury incurred in tissue, surgeons generally rely on visual observation which is subjective. In this work, we investigate the use of optical spectroscopy methods as a potentially more reliable approach. Previous work by various groups was strongly suggestive that tissue autofluorescence from NADH obtained under UV excitation is sensitive to metabolic response changes. To test and expand upon this concept, we monitored autofluorescence and light scattering intensities of injured vs. uninjured rat kidneys via multimodal imaging under 355 nm, 325 nm, and 266 nm excitation as well as scattering under 500 nm illumination. 355 nm excitation was used to probe mainly NADH, a metabolite, while 266 nm excitation was used to probe mainly tryptophan to correct for non-metabolic signal artifacts. The ratio of autofluorescence intensities derived under these two excitation wavelengths was calculated and its temporal profile was fit to a relaxation model. Time constants were extracted, and longer time constants were associated with kidney dysfunction. Analysis of both the autofluorescence and light scattering images suggests that changes in microstructure tissue morphology, blood absorption spectral characteristics, and pH contribute to the behavior of the observed signal which may be used to obtain tissue functional information and offer predictive capability.

59 BASIC BIOLOGICAL SCIENCES↗

Modifiable Array Data Structures for Mesh Topology

Topological data structures are useful in many areas, including the various mesh data structures used in finite element and finite volume applications. Here, we present a mesh data structure which is both flexible enough to support general mesh adaptivity and is compactly stored in a few large arrays. This structure can efficiently store full topological information for meshes with mixed element types. It allows both constant-time adjacency queries and constant-time addition and removal of mesh entities. We compare this structure to similar structures for finite elements and graphics and present its performance for adjacency queries. We also present its use in adaptive simulation applications.

97 MATHEMATICS AND COMPUTING↗