Search NASA⌕ Search

SEARCH · Search NASA

Results for “Trailing edges”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The effect of acoustic forcing on trailing edge separation and near wake development of an airfoil

An experimental study was conducted to investigate the effect of acoustic forcing on flow fields near the trailing edge of a symmetric airfoil at zero angle of attack. At low chord Reynolds numbers, the boundary layers separate from the surfaces in the rear part of the airfoil and create recirculation regions near the trailing edge. It is shown that with the introduction of acoustic forcing through a slot in the vicinity of the separation point, periodic large-scale structures are generated in the trailing edge region. Significant reduction of trailing edge separation is achieved. It is also found that the most effective forcing frequency to control trailing edge separation is the wake vortex shedding frequency. As a result of forcing, applied only on the upper surface, the upper boundary layer is accelerated and the flow over the lower surface decelerated. Consequently, an asymmetric wake is formed. The results presented indicate that the development of the near wake varies with forcing conditions.

Huang, L. S.↗
NASA NTRS1973

Externally blown flap trailing edge noise reduction by slot blowing: A preliminary study

Short takeoff and landing (STOL) aircraft using externally blown flaps (EBF) for lift augmentation develop considerable jet-flap interaction noise. A proposed method to reduce the EBF trailing edge noise is to locate a slot near the trailing edge of a flap through which low velocity secondary air is blown. Limited OASPL noise data were obtained from the interaction of the jet exhaust from a 5.08 cm diameter convergent nozzle with the trailing edge of a plate, and are presented for five slot configurations located near or at the trailing edge of the plate. Also presented are some significant jet trailing edge interaction data using a mixer nozzle with one of the slot configurations.

Mckinzie, D. J., Jr.↗
NASA NTRS1980

Numerical prediction of vortex cores of the leading and trailing edges of delta wings

The purpose of the present paper is to predict the roll-up of the vortex sheets emanating from the leading- and trailing-edges of delta wings with emphasis on the interaction of vortex cores beyond the trailing edge. The motivation behind the present work is the recent experimental data published by Hummel. The Nonlinear Discrete-Vortex method (NDV-method) is modified and extended to predict the leading- and trailing-vortex cores beyond the trailing edge. The present model alleviates the problems previously encountered in predicting satisfactory pressure distributions. This is accomplished by lumping the free-vortex lines during the iteration procedure. The leading- and trailing-edge cores and their feeding sheets are obtained as parts of the solution. The numerical results show that the NDV-method is successful in confirming the formation of a trailing-edge core with opposite circulation and opposite roll-up to those of the leading-edge core. This work is a breakthrough in the high angle of attack aerodynamics and moreover, it is the first numerical prediction done on this problem

Kandil, O. A.↗
NASA NTRS1981

Trailing edge noise prediction from measured surface pressures

Trailing edge (TE) noise is investigated for the case of a two-dimensional airfoil embedded in a uniform low Mach number flow, and the usefulness of several TE noise theories is examined by applying them to the measured data. The TE noise spectra and directivity are quantitatively determined for the case of a high Reynolds number and a fully turbulent boundary layer. Parameters include angle of attack, flow velocity and TE bluntness. Evanescent wave theories by Chase (1975) and Chandiramani (1974) are compared to the present results and show good agreement. Agreement of the near field pressure scatter phenomenon analysis with measurements implies that the basic assumptions used in the analysis are correct, i.e., the turbulent boundary layer (TBL) flow passes the trailing edge into the wake region. No hydrodynamic wake shedding activity is confirmed for the two-sided TBL flow, and a method incorporating the principles of the coherent output power method is used to determine the sound field. The near field edge scatter model is found to not only establish optimum sizing of edge treatment for noise control, but also to separate and identify the scattered field from the incident hydrodynamic field.

Brooks, T. F.↗
NASA NTRS1980

Trailing edge noise from hovering rotors

A method has been developed to predict the high frequency broadband noise due to the interaction of convecting turbulent eddies with the trailing edges of a hovering rotor. The trailing edge noise from each blade was modeled as point dipole noise with spanwise loading corrections. This point dipole approximation was checked by applying the concept to a stationary airfoil in a moving medium with excellent results. In order to estimate the strength of the point dipole, the trailing edge noise theory of Amiet was used. The method was applied specifically to blade boundary layer turbulence and compared to incident atmospheric turbulence noise. The results indicate that the relative importance of these two mechanisms is related to the magnitudes of the intensity and of the length scales of the inflow and boundary layer turbulence. The results tend to fall below some available experimental data indicating that in those experiments other broadband noise sources were stronger than boundary layer-trailing edge noise. The approach which was developed is also applicable to other blade-turbulence interaction mechanisms such as local stall and tip noise.

Kim, Y. N.↗
NASA NTRS1975

Cold air study of the effect on turbine stator blade aerodynamic performance of coolant ejection from various trailing edge slot geometries. 2: Comparison of experimental and analytical results

Experimentally determined efficiencies of turbine stator blades having trailing-edge coolant ejection are compared with efficiencies predicted from two previously published approximate analytical methods. The experimental results were obtained from two-dimensional data with the temperature of the primary and coolant flows both being nearly ambient. Data from five stator blade configurations having different slotted trailing-edge geometries were included in the comparison. The two analytical methods gave results which agreed reasonably well with experimental results. An average of the absolute values of differences between experimental and predicted efficiencies for all five blade configurations showed that one method gave average efficiency differences which were about 1.3 percent different than experimental efficiencies, while the other method gave average efficiency differences that were about 0.7 percent different than experimental. However, in some instances, maximum differences of as much as 4 percent occurred. A comparison between experimental and analytical results indicated that the ratio of trailing-edge slot width to trailing-edge thickness influences the measured efficiencies to a greater extent than is accounted for by either analytical model.

Prust, H. W., Jr.↗
NASA NTRS1977

FORTRAN program for calculating leading and trailing-edge geometry of turbomachine blades

A FORTRAN IV program which calculates leading- and trailing-edge circle radii, tangency angles on the leading- and trailing-edge circles, and stagger angles of turbomachinery blade sections using only spline points defining the blade surfaces is described. The program shifts the origin of the blade coordinates to the leading edge of the blade. Required input includes (m, theta) coordinates of a sufficient number of spline points to adequately define the two surfaces of the blade. Other required input are the radii from the axis of rotation of the leading- and trailing-edges. The output from this program is used directly as the geometrical input for a NASA developed program for calculating transonic velocities on a blade-to-blade stream surface of a turbomachine. The program is used for axial, radial, and mixed flow turbomachine blades.

Schumann, L. F.↗
NASA NTRS1984

Trailing edge flow conditions as a factor in airfoil design

Some new developments relevant to the design of single-element airfoils using potential flow methods are presented. In particular, the role played by the non-dimensional trailing edge velocity in design is considered and the relationship between the specified value and the resulting airfoil geometry is explored. In addition, the ramifications of the unbounded trailing edge pressure gradients generally present in the potential flow solution of the flow over an airfoil are examined, and the conditions necessary to obtain a class of airfoils having finite trailing edge pressure gradients developed. The incorporation of these conditions into the inverse method of Eppler is presented and the modified scheme employed to generate a number of airfoils for consideration. The detailed viscous analysis of airfoils having finite trailing edge pressure gradients demonstrates a reduction in the strong inviscid-viscid interactions generally present near the trailing edge of an airfoil.

Ormsbee, A. I.↗
NASA NTRS1988

Pressure distributions from subsonic tests of an advanced laminar-flow-control wing with leading- and trailing-edge flaps

An unswept, semispan wing model equipped with full-span leading- and trailing-edge flaps was tested in the Langley 14- by 22-Foot Subsonic Tunnel to determine the effect of high-lift components on the aerodynamics of an advanced laminar-flow-control (LFC) airfoil section. Chordwise pressure distributions near the midsemispan were measured for four configurations: cruise, trailing-edge flap only, and trailing-edge flap with a leading edge Kreuger flap of either 0.10 or 0.12 chord. Part 1 of this report presents a representative sample of the plotted pressure distribution data for each configuration tested. Part 2 (under separate cover) presents the entire set of plotted and tabulated pressure distribution data. The data are presented without analysis.

Applin, Zachary T.↗
NASA NTRS1988

Pressure distributions from subsonic tests of an advanced laminar-flow-control wing with leading- and trailing-edge flaps

An unswept, semispan wing model equipped with full-span leading- and trailing-edge flaps was tested in the Langley 14- by 22-Foot Subsonic Tunnel to determine the effect of high-lift components on the aerodynamics of an advanced laminar-flow-control (LFC) airfoil section. Chordwise pressure distributions near the midsemispan were measured for four configurations: cruise, trailing-edge flap only, and trailing-edge flap with a leading-edge Krueger flap of either 0.10 or 0.12 chord. Part 1 of this report (under separate cover) presents a representative sample of the plotted pressure distribution data for each configuration tested. Part 2 presents the entire set of plotted and tabulated pressure distribution data. The data are presented without analysis.

Applin, Zachary T.↗
NASA NTRS1927

Experiments on airfoils with trailing edge cut away

Airfoils with their trailing edge cut away are often found on aircraft, as the fins on the hulls of flying boats and the central section of the wings for affording better visibility. It was therefore of some interest to discover the effect of such cutaways on the lift and drag and on the position of the center of pressure. For this purpose, systematic experiments were performed on two different airfoils, a symmetrical airfoil and an airfoil of medium thickness, with successive shortenings of their chords.

AIRFOILS↗
NASA NTRS1991

The symmetric turbulent plane wake downstream of a sharp trailing edge

The analysis and modeling of the symmetric turbulent plane wake downstream of a sharp trailing edge is addressed. A compact description of the flow near the trailing edge is formulated using the results of a previous asymptotic analysis. The new description retains the two-layered structure identified in the previous work, and it clarifies the principal dynamics of the flow in the near-wake outer layer, away from the wake centerline. For zero-pressure-gradient flow, the near-wake outer layer is shown to be represented to leading order by the similarity solution that governs the outer region of the surface boundary layer. The leading perturbation in the outer layer due to the developing near-wake inner-layer flow is identified, and this is shown to be asymptotically smaller than undetermined higher-order terms associated with the surface boundary-layer flow. Results of the new near-wake analysis are used to formulate an algebraic eddy viscosity model for wake flow predictions at arbitrary distances from the trailing edge. The model is used in a numerical solution of the boundary layer equations, and computed velocity and Reynolds stress profiles are shown to compare well with experimental data.

Bogucz, E. A.↗
NASA NTRS1975

Flow visualization of vortices locked by spanwise blowing over wings featuring a unique leading and trailing-edge flap system

Flow visualization studies were conducted to qualitatively determine the effects of active generation and augmentation of vortex flow over wings by blowing a discrete jet in a spanwise direction in the channel formed by extension of upper surface leading- and trailing-edge flaps. Spanwise blowing from a reflection plane over a rectangular wing was found to generate and lock a dual corotating vortex system within the channel and, at sufficient blowing rates, cause the separated flow off the upper end of the leading-edge flap to reattach to the trailing-edge flap. Test parameters included wing angle of attack, jet momentum coefficient, leading- and trailing-edge flap deflection angle, and jet location above the wing surface. Effects due to removal of the leading- and trailing-edge flap were also investigated.

Erickson, G. E.↗
NASA NTRSDate not supplied

The Effect of Trailing Edge Grid Resolution in Large-Eddy Simulations

Ceramic Matrix Composite (CMC) with environmental barrier coating can tolerate significantly higher temperatures compared with the conventional metal alloy blades and thus can help achieve higher thermal efficiency in gas turbine engines. Due to the complex fabrication process of CMC blades, larger blade trailing edge thicknesses and larger leading-edge radii of curvature are expected. These features significantly alter aerodynamic performance especially near the trailing edge and thus the loss profile. In previous studies, the authors used the large eddy simulation (LES) as well as the Reynolds Averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model to simulate an aerodynamics performance of three different CMC blades and compared the predictions against the data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Although we were able to successfully predict different characteristics of aerodynamic performance among three different blades (e.g., pressure loading and integrated losses), LES consistently predicted a small recirculation bubble at the end of the suction side. This was not inconsistent with the physics of the flow, but the pressure loading, locally, near the trailing edge, and as a result, the measured wake profiles did not match the experimental data. To delve further into these issues, a new LES grid with a much finer mesh near the trailing edge was generated where the spanwise extent of the grid was increased by 50%. An LES simulation for the CMC blade with the largest trailing edge thicknesses at the high-freestream turbulence (Tu=13%) condition showed that using such a mesh is necessary for LES to accurately capture the transition phenomena on the suction side. The resulting total pressure coefficient profile and the shift of the wake profile were greatly improved.

CMC↗
NASA NTRSDate not supplied

The Effect of Trailing Edge Grid Resolution in Large-Eddy Simulations

Ceramic Matrix Composite (CMC) with environmental barrier coating can tolerate significantly higher temperatures compared with the conventional metal alloy blades and thus can help achieve higher thermal efficiency in gas turbine engines. Due to the complex fabrication process of CMC blades, larger blade trailing edge thicknesses and larger leading-edge radii of curvature are expected. These features significantly alter aerodynamic performance especially near the trailing edge and thus the loss profile. In previous studies, the authors used the large eddy simulation (LES) as well as the Reynolds Averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model to simulate an aerodynamics performance of three different CMC blades and compared the predictions against the data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Although we were able to successfully predict different characteristics of aerodynamic performance among three different blades (e.g., pressure loading and integrated losses), LES consistently predicted a small recirculation bubble at the end of the suction side. This was not inconsistent with the physics of the flow, but the pressure loading, locally, near the trailing edge, and as a result, the measured wake profiles did not match the experimental data. To delve further into these issues, a new LES grid with a much finer mesh near the trailing edge was generated where the spanwise extent of the grid was increased by 50%. An LES simulation for the CMC blade with the largest trailing edge thicknesses at the high-freestream turbulence (Tu=13%) condition showed that using such a mesh is necessary for LES to accurately capture the transition phenomena on the suction side. The resulting total pressure coefficient profile and the shift of the wake profile were greatly improved.

LES↗
NASA NTRS2002

Low-Speed Fan Noise Reduction With Trailing Edge Blowing

An experimental proof-of-concept test was conducted to demonstrate reduction of rotor-stator interaction noise through rotor-trailing edge blowing. The velocity deficit from the viscous wake of the rotor blades was reduced by injecting air into the wake from a trailing edge slot. Composite hollow rotor blades with internal flow passages were designed based on analytical codes modeling the internal flow. The hollow blade with interior guide vanes creates flow channels through which externally supplied air flows from the root of the blade to the trailing edge. The impact of the rotor wake-stator interaction on the acoustics was also predicted analytically. The Active Noise Control Fan, located at the NASA Glenn Research Center, was used as the proof- of-concept test bed. In-duct mode and farfield directivity acoustic data were acquired at blowing rates (defined as mass supplied to trailing edge blowing system divided by fan mass flow) ranging from 0.5 to 2.0 percent. The first three blade passing frequency harmonics at fan rotational speeds of 1700 to 1900 rpm were analyzed. The acoustic tone power levels (PWL) in the inlet and exhaust were reduced 11.5 and -0.1, 7.2 and 11.4, 11.8 and 19.4 PWL dB, respectively. The farfield tone power levels at the first three harmonics were reduced 5.4, 10.6, and 12.4 dB PWL. At selected conditions, two-component hotwire and stator vane unsteady surface pressures were acquired. These measurements illustrate the physics behind the noise reduction.

Sutliff, Daniel L.↗
NASA NTRS1983

Reduction of the shock wave intensity by modifying the transonic blade trailing edge

It is shown that the shock wave intensity can be decreased by using modified trailing edge configurations to reduce or even completely compensate for the effect of the finite thickness of the trailing edge. A theoretical analysis is presented together with numerical results for two supersonic streams flowing off the trailing edge at different velocities. The analysis is based on an ideal gas model.

Doerffer, P.↗
NASA NTRS2005

Broadband Noise Reduction of a Low-Speed Fan Noise Using Trailing Edge Blowing

An experimental proof-of-concept test was conducted to demonstrate reduction of rotor-stator interaction noise through the use of rotor-trailing edge blowing. The velocity deficit from the viscous wake of the rotor blades was reduced by injecting air into the wake from a continuous trailing edge slot. Hollow blades with interior guide vanes create flow channels through which externally supplied air flows from the blade root to the trailing edge. A previous paper documented the substantial tonal reductions of this Trailing Edge Rotor Blowing (TERB) fan. This report documents the broadband characteristics of TERB. The Active Noise Control Fan (ANCF), located at the NASA Glenn Research Center, was used as the proof-of-concept test bed. Two-component hotwire data behind the rotor, unsteady surface pressures on the stator vane, and farfield directivity acoustic data were acquired at blowing rates of 1.1, 1.5, and 1.8 percent of the total fan mass flow. The results indicate a substantial reduction in the rotor wake turbulent velocity and in the stator vane unsteady surface pressures. Based on the physics of the noise generation, these indirect measurements indicate the prospect of broadband noise reduction. However, since the broadband noise generated by the ANCF is rotor-dominated, any change in the rotor-stator interaction broadband noise levels is barely distinguishable in the farfield measurements.

Sutliff, Daniel L.↗