SEARCH · Search NASA

Results for “Twist angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Computational wing optimization and comparisons with experiment for a semi-span wing model

A computational wing optimization procedure was developed and verified by an experimental investigation of a semi-span variable camber wing model in the NASA Ames Research Center 14 foot transonic wind tunnel. The Bailey-Ballhaus transonic potential flow analysis and Woodward-Carmichael linear theory codes were linked to Vanderplaats constrained minimization routine to optimize model configurations at several subsonic and transonic design points. The 35 deg swept wing is characterized by multi-segmented leading and trailing edge flaps whose hinge lines are swept relative to the leading and trailing edges of the wing. By varying deflection angles of the flap segments, camber and twist distribution can be optimized for different design conditions. Results indicate that numerical optimization can be both an effective and efficient design tool. The optimized configurations had as good or better lift to drag ratios at the design points as the best designs previously tested during an extensive parametric study.

Waggoner, E. G.↗

NASA NTRS1984

Lewis Research Center spin rig and its use in vibration analysis of rotating systems

The Lewis Research Center spin rig was constructed to provide experimental evaluation of analysis methods developed under the NASA Engine Structural Dynamics Program. Rotors up to 51 cm (20 in.) in diameter can be spun to 16,000 rpm in vacuum by an air motor. Vibration forcing functions are provided by shakers that apply oscillatory axial forces or transverse moments to the shaft, by a natural whirling of the shaft, and by an air jet. Blade vibration is detected by strain gages and optical blade-tip motion sensors. A variety of analogy and digital processing equipment is used to display and analyze the signals. Results obtained from two rotors are discussed. A 56-blade compressor disk was used to check proper operation of the entire spin rig system. A special two-blade rotor was designed and used to hold flat and twisted plates at various setting and sweep angles. Accurate Southwell coefficients have been obtained for several modes of a flat plate oriented parallel to the plane of rotation.

Brown, G. V.↗

NASA NTRS1997

Videometric Applications in Wind Tunnels

Videometric measurements in wind tunnels can be very challenging due to the limited optical access, model dynamics, optical path variability during testing, large range of temperature and pressure, hostile environment, and the requirements for high productivity and large amounts of data on a daily basis. Other complications for wind tunnel testing include the model support mechanism and stringent surface finish requirements for the models in order to maintain aerodynamic fidelity. For these reasons nontraditional photogrammetric techniques and procedures sometimes must be employed. In this paper several such applications are discussed for wind tunnels which include test conditions with Mach number from low speed to hypersonic, pressures from less than an atmosphere to nearly seven atmospheres, and temperatures from cryogenic to above room temperature. Several of the wind tunnel facilities are continuous flow while one is a short duration blowdown facility. Videometric techniques and calibration procedures developed to measure angle of attack, the change in wing twist and bending induced by aerodynamic load, and the effects of varying model injection rates are described. Some advantages and disadvantages of these techniques are given and comparisons are made with non-optical and more traditional video photogrammetric techniques.

Burner, A. W.↗

NASA NTRS2014

Preliminary Assessment of Optimal Longitudinal-Mode Control for Drag Reduction through Distributed Aeroelastic Shaping

The emergence of advanced lightweight materials is resulting in a new generation of lighter, flexible, more-efficient airframes that are enabling concepts for active aeroelastic wing-shape control to achieve greater flight efficiency and increased safety margins. These elastically shaped aircraft concepts require non-traditional methods for large-scale multi-objective flight control that simultaneously seek to gain aerodynamic efficiency in terms of drag reduction while performing traditional command-tracking tasks as part of a complete guidance and navigation solution. This paper presents results from a preliminary study of a notional multi-objective control law for an aeroelastic flexible-wing aircraft controlled through distributed continuous leading and trailing edge control surface actuators. This preliminary study develops and analyzes a multi-objective control law derived from optimal linear quadratic methods on a longitudinal vehicle dynamics model with coupled aeroelastic dynamics. The controller tracks commanded attack-angle while minimizing drag and controlling wing twist and bend. This paper presents an overview of the elastic aircraft concept, outlines the coupled vehicle model, presents the preliminary control law formulation and implementation, presents results from simulation, provides analysis, and concludes by identifying possible future areas for research

aeroelastic↗

NASA NTRS1990

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

For advanced gas turbine engines, two combustor systems, the lean premixed/prevaporized (LPP) and the rich burn/quick quench/lean burn (RQL) offer great potential for reducing NO(x) emissions. An important consideration for either concept is the development of an advanced fuel injection system that will provide a stable, efficient, and very uniform combustion system over a wide operating range. High-shear airblast fuel injectors for gas turbine combustors have exhibited superior atomization and mixing compared with pressure-atomizing fuel injectors. This improved mixing has lowered NO(x) emissions and the pattern factor, and has enabled combustors to alternate fuels while maintaining a stable, efficient combustion system. The performance of high-shear airblast fuel injectors is highly dependent on the design of the dome swirl vanes. The type of swirl vanes most widely used in gas turbine combustors are usually flat for ease of manufacture, but vanes with curvature will, in general, give superior aerodynamic performance. The design and performance of high-turning, low-loss curved dome swirl vanes with twist along the span are investigated. The twist induces a secondary vortex flow pattern which will improve the atomization of the fuel, thereby producing a more uniform fuel-air distribution. This uniform distribution will increase combustion efficiency while lowering NO(x) emissions. A systematic swirl vane design system is presented based on one-, two-, and three-dimensional flowfield calculations, with variations in vane-turning angle, rate of turning, vane solidity, and vane twist as design parameters.

Micklow, Gerald J.↗

NASA NTRS1990

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

Micklow, Gerald J.↗

NASA NTRS1972

Effect of wing design on the longitudinal aerodynamic characteristics of a wing-body model at subsonic speeds

An investigation has been conducted to determine the effects of wing camber and twist on the longitudinal aerodynamic characteristics of a wingbody configuration. Three wings were used each having the same planform (aspect ratio of 2.5 and leading-edge sweep angle of 44 deg.) but differing in amounts of camber and twist (wing design lift coefficient). The wing design lift coefficients were 0, 0.35, and 0.70. The investigation was conducted over a Mach number range from 0.20 to 0.70 at angles of attack up to about 22 deg. The effect of wing strakes on the aerodynamic characteristics of the cambered wings was also studied. A comparison of the experimentally determined aerodynamic characteristics with theoretical estimates is also included.

Henderson, W. P.↗

NASA NTRS1983

Global characteristics of magnetic flux ropes in the Venus ionosphere

An examination is undertaken of global characteristics of Venus ionosphere magnetic flux ropes, whose maximum spatial occurrence at 165-km altitude occupies more than half of the ionospheric volume. Ropes above 200 km altitude in the low zenith angle regions appear to have quasi-horizontal orientations, while those below that altitude tend to be quasi-vertical. High zenith angle cases tend to be horizontal above 300 km, and randomly oriented below that altitude. Ropes may be more tightly 'twisted' at low than at high altitudes, especially in the low zenith angle regions. Rope field strengths are highest near the altitudes where their occurrence is greatest, and scale with the square root of the ambient thermal pressure. The global polarities of flux rope field-aligned currents seem to be random and do not support a steady, nonturbulent global formation mechanism.

Elphic, R. C.↗

NASA NTRS1979

A photometric determination of twists in three early-type galaxies

Detailed photometric data have been obtained for three early-type galaxies by using the Cerro Tololo 1.5-m telescope and an SEC television camera. The aim of this photometry is to gain further accurate information on the occurrence of twists in such galaxies; i.e., on any variations with radius of the position angle of the major axes of the isophotes. The results of the photometry are: (1) the finding of no detectable twist within the bulge of the S0 galaxy NGC 5102; (2) confirmation of a substantial twist (about 10 deg) in the inner portion of the E3 galaxy IC 1459; and (3) determination of a moderate twist (about 5 deg) within the E4 galaxy NGC 4697, possibly too small to have been previously detected. If such moderate twists should turn out to be common in elliptical galaxies, the suspicion of triaxiality for most such galaxies would be enhanced.

Williams, T. B.↗

NASA NTRS1991

Low-speed aerodynamics of the trailed-rotor high-speed rotorcraft concept in cruise configuration

An experimental investigation was performed to determine the low-speed aerodynamic performance characteristics of the trailed-rotor high-speed rotorcraft concept in its cruise configuration. A 15 percent scale semispan model was tested at speeds up to 180 knots in the NASA Ames 7-by 10-Foot Subsonic Wind Tunnel. The objective of this investigation was to determine specific aerodynamic performance characteristics to assist in evaluating the trailed rotor as a high-speed rotorcraft. The aerodynamic influence of the following model configuration changes were determined: ailerons, flaps, wing/pod angle, number of trailed blades, trailed-blade twist and azimuth, and wing/pod filet radius. The low-speed performance objectives for the concept were met and results indicated that the trailed-rotor model had no significant adverse aerodynamic characteristics. The optimum low-speed cruise configuration was determined. Results suggest the trailed-rotor concept has better low-speed cruise performance characteristics than the folding tiltrotor configuration.

Johnson, Jeffrey L.↗

NASA NTRS1951

Experimental investigation of an 0.8 hub-tip radius-ratio,nontwisted-rotor-blade turbine

An experimental investigation of a 0.8 hub-tip radius ratio, nontwisted-rotor-blade turbine designed for a stagnation-pressure ratio of 2.5 and an equivalent mean blade speed of 643 feet per second was made in a cold-air turbine with (a) nontwisted stator blades, and (b) twisted stator blades designed to maintain zero rotor-inlet incidence angles. Turbine efficiencies of the order of 0.85 at the design point were obtained with a nontwisted-rotor-blade turbine with a hub-tip radius ratio of 0.80. The turbine with the twisted stator blades gave higher efficiencies at the design point (of the order of 1.5 percentage points) than the turbine with the nontwisted stator blades.

TURBINES - AXIAL FLOW↗

NASA NTRS1987

Stresses and deformations in angle-ply composite tubes

The stress and deformations in angle-ply composite tubes subjected to axisymmetric thermal loading were investigated both experimentally and analytically. For the theoretical portion a generalized plane strain elasticity analysis was developed. The analysis included mechanical and thermal loading, and temperature-dependent material properties. The elasticity analysis was also used to study the effect of including a thin metallic coating on a graphite-epoxy tube. The stresses in the coatings were found to be quite high, exceeding the yield stress of aluminum. An important finding in the analytical studies was the fact that even tubes with a balanced-symmetric lamination sequence exhibit shear deformation, or twist. For the experimental portion an apparatus was developed to measure torsional and axial response in the temperature range of 140 to 360 K. Eighteen specimens were tested, combining three material systems, eight lamination sequences, and three off-axis ply orientation angles. For the twist response, agreement between analysis and experiment was found to be good. The axial response of the tubes tested was found to be greater than predicted by a factor of three. As a result, it is recommended that the thermally induced axial deformations be investigated, both experimentally and analytically.

Rousseau, Carl Q.↗

NASA NTRS1993

Aeroelastic airfoil smart spar

Aircraft wings and rotor-blades are subject to undesirable bending and twisting excursions that arise from unsteady aerodynamic forces during high speed flight, abrupt maneuvers, or hard landings. These bending excursions can range in amplitude from wing-tip flutter to failure. A continuous-filament construction 'smart' laminated composite box-beam spar is described which corrects itself when subject to undesirable bending excursions or flutter. The load-bearing spar is constructed so that any tendency for the wing or rotor-blade to bend from its normal position is met by opposite twisting of the spar to restore the wing to its normal position. Experimental and theoretical characterization of these spars was made to evaluate the torsion-flexure coupling associated with symmetric lay-ups. The materials used were uniweave AS-4 graphite and a matrix comprised of Shell 8132 resin and U-40 hardener. Experimental tests were conducted on five spars to determine spar twist and bend as a function of load for 0, 17, 30, 45 and 60 deg fiber angle lay-ups. Symmetric fiber lay-ups do exhibit torsion-flexure couplings. Predictions of the twist and bend versus load were made for different fiber orientations in laminated spars using a spline function structural analysis. The analytical results were compared with experimental results for validation. Excellent correlation between experimental and analytical values was found.

Greenhalgh, Skott↗

NASA NTRS1977

An experimental-theoretical correlation study of non-linear bending and torsion deformations of a cantilever beam

An experimental study of the large deformation of a cantilevered beam under a gravity tip load has been made. The beam root is rotated so that the tip load is oriented at various angles with respect to the beam principal axes. Static twist and bending deflections of the tip and bending natural frequencies have been measured as a function of tip load magnitude and orientation. The experimental data are compared with the results of a recently developed non-linear structural theory. Agreement is reasonably good when bending deflections are small compared to the beam span, but systematic differences occur for larger deflections.

Dowell, E. H.↗

NASA NTRS1988

Optimization of slender wings for center-of-pressure shift due to change in Mach number

It is observed that the center of pressure on a wing shifts as the Mach number is changed. Such shifts are in general undesirable and are sometimes compensated for by actively shifting the center of gravity of the aircraft or by using active stability controls. To avoid this complication, it is desirable to design the wings of a high speed aircraft so as to minimize the extent of the center-of-pressure shifts. This, together with a desire to minimize the center-of-pressure shifts in missile control surfaces, provides the motivation for this project. There are many design parameters which affect center-of-pressure shifts, but it is expected that the largest effects are due to the wing planform. Thus, for the sake of simplicity, this study is confined to an investigation of thin, flat, (i.e., no camber or twist), relatively slender, pointed wings flying at a small angle of attack. Once the dependence of the center of pressure on planform and Mach number is understood, we can expect to investigate the sensitivity of the center-of-pressure shifts to various other parameters.

Andersen, Carl M.↗

NASA NTRS1993

Laser velocimeter measurements of the flow field generated by a forward-swept propfan during flutter

Results are presented from an investigation to measure the flow field generated by a forward-swept propfan operating in flutter at a low forward velocity. For comparison to the flutter condition, flow field data are also presented for a slightly reduced rotational speed just below flutter. The forward-swept propfan was tested as the front rotor of a counterrotating pusher propeller. A laser Doppler velocimeter (LDV) was used to measure the velocity field in planes normal to the model centerline downstream of the rotor and in planes of constant radius within the blade passages at each operating condition. The mean time-averaged flow about the blades did not change drastically as the propfan rotational speed was increased from the stable operating point to the flutter condition. No regions of flow separation could be identified in the data plots of the mean intrablade flow field. The relative flow about the blades remained subsonic during flutter operation. The blades were found to have a higher than expected tip loading at both operating conditions. This is thought to have been caused by the outer blade sections twisting under load to higher than expected effective blade angles. This high tip loading resulted in strong vortices and a very nonuniform flow downstream of the tips of the forward-swept blades. This high tip loading may also have caused the blade flutter.

Podboy, Gary G.↗

NASA NTRS1993

Laser velocimeter measurements of the flow field generated by a forward-swept propfan during flutter

Results are presented from an investigation to measure the flow field generated by a forward-swept propfan operating in flutter at a low forward velocity. For comparison to the flutter condition, flow field data are also presented for a slightly reduced rotational speed just below flutter. The forward-swept propfan was tested as the front rotor of a counterrotating pusher propeller. A laser Doppler velocimeter (LDV) was used to measure the velocity field in planes normal to the model centerline downstream of the rotor and in planes of constant radius within the blade passages at each operating condition. A comparison of the data taken at the two different operating conditions indicated that the mean, time-averaged flow about the blades did not change drastically as the propfan rotational speed was increased from the stable operating point to the flutter condition. No regions of flow separation could be identified in the data plots of the mean intrablade flow field. The data also indicate that the relative flow about the blades remained subsonic during flutter operation. The blades were found to have a higher than expected tip loading at both operating conditions. This is thought to have been caused by the outer blade sections twisting under load to higher than expected effective blade angles. This high tip loading resulted in strong vortices and a very nonuniform flow downstream of the tips of the forward-swept blades. This high tip loading may also have caused the blade flutter.

Podboy, Gary G.↗

NASA NTRS1952

Effect of Rotor- and Stator-Blade Modifications on Surge Performance of an 11-Stage Axial-Flow Compressor. I - Original Production Compressor of XJ40-WE-6 Engine

An investigation to increase the compressor surge-limit pressure ratio of the XJ40-WE-6 turbojet engine at high equivalent speeds was conducted at the NACA Lewis altitude wind tunnel. This report evaluates the compressor modifications which were restricted to (1) twisting rotor blades (in place) to change blade section angles and (2) inserting new stator diaphragms with different blade angles. Such configuration changes could be incorporated quickly and easily in existing engines at overhaul depots. It was found that slight improvements in the compressor surge limit were possible by compressor blade adjustment. However, some of the modifications also reduced the engine air flow and hence penalized the thrust. The use of a mixer assembly at the compressor outlet improved the surge limit with no appreciable thrust penalty.

Finger, Harold B.↗