Search NASA⌕ Search

SEARCH · Search NASA

Results for “UAv”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Drones for Decommissioning

The U.S. Nuclear Regulatory Commission has responsibility for regulating the safe decommissioning of facilities and sites to meet the License Termination Rule in 10 Code of Federal Regulations (CFR) Part 20, Standards for Protection Against Radiation, Subpart E “Radiological Criteria for License Termination.” Decommissioning is performed in accordance with 10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities, as part of license termination (§50.82) and release of the facility or site for unrestricted use (§50.83). The guidance currently demonstrates the minimum requirements and necessary conditions for conducting radiological surveys by a person carrying a radiation detector(s). The Pacific Northwest National Laboratory (PNNL) evaluated the use of an unoccupied aerial vehicle (UAV) to conduct radiological surveys that could be used in decommissioning to potentially reduce time, cost, and worker safety compared to current survey methods. The objective of this project was to evaluate the performance and limitations of a UAV to support a decommissioning radiological survey and compare it to a radiological survey conducted by a human. The primary research questions of interest evaluated were: 1. Did observed UAV paths differ from human paths and, if so, how much? 2. Did survey path deviation affect survey results and, if so, how? 3. Were radiological measurements from human and UAV surveys significantly different? To answer these research questions, an experimental field was set up at PNNL’s 3440 test track, and it included radiological sources commonly surveyed during decommissioning: cobalt-60 (Co-60), cesium-137 (Cs-137), and americium-241 (Am-241). Nine check sources (three each of Am-241, Cs-137, and Co-60) with activities ranging from 3.54 µCi to 39.34 µCi were set over a path that also included an area for measuring background radiation. An Aurelia X6 UAV coupled with a GPS and lidar unit was used to conduct the radiological surveys. UAV and human surveys were conducted using two different NaI(Tl) scintillation radiation detectors (2 in. × 2 in. Ludlum, Inc. and 2 in. × 0.04 in. Alpha Spectra, Inc.) at a travel velocity of approximately 0.2 m/s at a low (15–40 cm median altitude) or high (87–105 cm median altitude) survey altitude. Since the survey velocity and altitude parameters were atypical for normal UAV operations, testing was done prior to conducting the radiological surveys to establish airworthiness, evaluate the navigation system, and establish flight control. Human and UAV surveys were paired according to the detector type and altitude regime to compare the survey data. The results of this proof-of-concept research determined that the UAV and human surveys followed similar survey paths and detected the radiological sources with no significant statistical difference (in 33 out of 36 surveys). However, further research is needed prior to deploying UAVs for decommissioning surveys.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

Energy‐aware relay positioning in flying networks

Summary The ability to move and hover has made rotary‐wing unmanned aerial vehicles (UAVs) suitable platforms to act as flying communications relays (FCRs), aiming at providing on‐demand, temporary wireless connectivity when there is no network infrastructure available or a need to reinforce the capacity of existing networks. However, since UAVs rely on their on‐board batteries, which can be drained quickly, they typically need to land frequently for recharging or replacing them, limiting their endurance and the flying network availability. The problem is exacerbated when a single FCR UAV is used. The FCR UAV energy is used for two main tasks: Communications and propulsion. The literature has been focused on optimizing both the flying network performance and energy efficiency from the communications point of view, overlooking the energy spent for the UAV propulsion. Yet, the energy spent for communications is typically negligible when compared with the energy spent for the UAV propulsion. In this article, we propose energy‐aware relay positioning (EREP), an algorithm for positioning the FCR taking into account the energy spent for the UAV propulsion. Building upon the conclusion that hovering is not the most energy‐efficient state, EREP defines the trajectory and speed that minimize the energy spent by the FCR UAV on propulsion, without compromising in practice the quality of service offered by the flying network. The EREP algorithm is evaluated using simulations. The obtained results show gains up to 26% in the FCR UAV endurance for negligible throughput and delay degradation.

Rodrigues, Hugo↗
DOE OSTI2023

Minimizing Ground Risk in Cellular-Connected Drone Corridors With mmWave Links

Unmanned Aircraft Systems (UASs) have been receiving significant interest and support from academia, industry, and regulatory bodies over the past decade due to their various use cases. To safely integrate UAS operations into the national airspace, particularly overpopulated regions, the risk posed to ground users, buildings, and vehicles due to unmanned aerial vehicle (UAV) flight should be minimized. This risk can be represented by a numerical metric, which we refer to in this article as the “ground risk.” Many UAS applications also depend on the presence of a reliable wireless communication link between the UAV and a control station for the transmission of UAV position, surveillance video, UAV payload commands, and other mission-related data. Such wireless communication requirements also need to be considered in the design of UAS operations. In this article, we consider both these aspects and study the design of nonintersecting trajectories for UAS operations to minimize ground risk, subject to constraints on the wireless signal strength and geometry of the trajectory, specified in terms of: 1) an enclosing cylinder within which the trajectory must lie and 2) an integrated angular change along the UAV's trajectory. The performance of a computationally expensive optimal algorithm is compared with that of a computationally faster heuristic approach within the dense urban environment of Manhattan, NY, USA. Performance evaluation using ray-tracing simulations shows that the heuristic approach performs close to the optimal algorithm at a reduced computation cost. In conclusion, this research can be utilized to make UAS operations safe and reliable and accelerate their adoption.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2021

Characterizing the performance of a POPS miniaturized optical particle counter when operated on a quadcopter drone

We first validate the performance of the Portable Optical Particle Spectrometer (POPS), a small light-weight and high sensitivity optical particle counter, against a reference scanning mobility particle sizer (SMPS) for a month-long deployment in an environment dominated by biomass burning aerosols. Subsequently, we examine any biases introduced by operating the POPS on a quadcopter drone, a DJI Matrice 200 V2. We report the root mean square difference (RMSD) and mean absolute difference (MAD) in particle number concentrations (PNCs) when mounted on the UAV and operating on the ground and when hovering at 10 m. When wind speeds are low (less than 2.6 m s –1 ), we find only modest differences in the RMSDs and MADs of 5 % and 3 % when operating at 10 m altitude. When wind speeds are between 2.6 and 7.7 m s –1 the RMSDs and MADs increase to 26.2 % and 19.1 %, respectively, when operating at 10m altitude. No statistical difference in PNCs was detected when operating on the UAV in either ascent or descent. We also find size distributions of aerosols in the accumulation mode (defined by diameter, d, where 0.1 ≤ d ≤ 1 µm) are relatively consistent between measurements at the surface and measurements at 10 m altitude, while differences in the coarse mode (here defined by d > 1 µm) are universally larger. Our results suggest that the impact of the UAV rotors on the POPS PNCs are small at low wind speeds, but when operating under a higher wind speed of up to 7.6 m s –1 , larger discrepancies occur. In addition, it appears that the POPS measures sub-micron aerosol particles more accurately than super-micron aerosol particles when airborne on the UAV. These measurements lay the foundations for determining the magnitude of potential errors that might be introduced into measured aerosol particle size distributions and concentrations owing to the turbulence created by the rotors on the UAV.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Routing Problem for Unmanned Aerial Vehicle Patrolling Missions - A Progressive Hedging Algorithm

This paper presents a two-stage stochastic program to model a routing problem involving an Unmanned Aerial Vehicle (UAV) in the context of patrolling missions. In particular, given a set of targets and a set of supplemental targets corresponding to each target, the first stage decisions involve finding the sequence in which the vehicle has to visit the set of targets. Upon reaching each target, the UAV collects information and if the operator of the UAV deems that the information collected is not of sufficient fidelity, then the UAV has to visit all the supplemental targets corresponding to that target to collect additional information before proceeding to visit the next target. The problem is solved using a progressive hedging algorithm and extensive computational results corroborating the effectiveness of the proposed model and the solution methodology is presented.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Decentralized modular hybrid supervisory control for the formation of unmanned helicopters

Abstract Formation control of Unmanned Aerial Vehicles (UAVs) requires them to tightly cooperate to reach and keep the formation, while avoiding collision. This paper proposes a novel decentralized hybrid supervisory control approach for the formation control of multiple UAVs. This is achieved by developing a symbolic motion planning technique to polarly partition the motion space resulting in a finite state discrete event model for the motion dynamics of each UAV. Then, a modular discrete supervisor is designed for different components of the formation mission including reaching the formation, keeping the formation, and collision avoidance. Further, for the collision avoidance mechanism, a novel top‐down decomposition‐based approach is developed to design local supervisors decentralizedly. It is formally proved that with the proposed top‐down decomposition‐based approach, the (locally) supervised UAVs, as a whole, can cooperatively satisfy the desired (global) collision avoidance specification. The proposed decentralized supervisory control algorithm is also verified through a hardware‐in‐the‐loop simulator for the formation control of unmanned helicopters.

Karimoddini, Ali↗
DOE OSTI2021

Beam Measurements of the Tianlai Dish Radio Telescope using an Unmanned Aerial Vehicle

Precision measurement of the beam pattern of an antenna is very important for many applications. While traditionally such measurement is often made in a microwave anechoic chamber or at a test range, measurement using an unmanned aerial vehicle offers a number of advantages: the measurement can be made for the assembled antenna on site, thus reflecting the actual characteristics of the antenna of interest, and more importantly, it can be performed for larger antennas which cannot be steered or easily measured using the anechoic chamber and test range. Here we report our beam measurement experiment with UAV for a 6 meter dish used in the Tianlai array, which is a radio astronomy experiment. Due to the dish's small collecting area, calibration with an astronomical source only allows for determining the antenna beam pattern over a very limited angular range. We describe in detail the setup of the experiment, the components of the signal transmitting system, the design of the flight path and the procedure for data processing. We find the UAV measurement of the beam pattern agrees very well with the astronomical source measurement in the main lobe, but the UAV measurement can be extended to the fourth side lobe. The measured position and width of each lobe also shows good agreement with electromagnetic field simulation. This UAV-based approach of beam pattern measurement is flexible and inexpensive, and the technique may also be applied to other experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Cooperative Routing for an Air–Ground Vehicle Team—Exact Algorithm, Transformation Method, and Heuristics

This paper considers a cooperative vehicle routing problem for an intelligence, surveillance, and reconnaissance mission in the presence of communication constraints between the vehicles. The proposed framework uses a ground vehicle and an unmanned aerial vehicle (UAV) that travel cooperatively and visit a set of targets while satisfying the communication constraints. The problem is formulated as a mixed-integer linear program, and a branch-and-cut algorithm is developed to solve the problem to optimality. Furthermore, a transformation method and a heuristic are also developed for the problem. The effectiveness of all the algorithms is corroborated through extensive computational experiments on several randomly generated instances. Furthermore, this paper is motivated by an intelligence, surveillance, and reconnaissance mission involving a single unmanned aerial vehicle (UAV) and a ground vehicle, where the vehicles must coordinate their activity in the presence of communication constraints. The combination of a small UAV and a ground vehicle is an ideal platform for such missions, since small UAVs can fly at low altitudes and can avoid obstacles or threats that would be problematic for the ground vehicle alone. This paper addresses the coordinated routing problem involving these two vehicles and presents an algorithm to obtain an optimal solution for this problem, fast heuristics to obtain good feasible solutions, and also a transformation method to transform any instance of this cooperative vehicle routing problem to an instance of the one-in-a-set traveling salesman problem.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Bounds on Optimal Revisit Times in Persistent Monitoring Missions With a Distinct and Remote Service Station</strong

We report persistent monitoring missions require an up-to-date knowledge of the changing state of the underlying environment. Unmannned aerial vehicles (UAVs) can be gainfully employed to continually visit a set of targets representing tasks (and locations) in the environment and collect data therein for long time periods. The enduring nature of these missions requires the UAV to be regularly recharged at a service station. In this article, we consider the case in which the service station is not colocated with any of the targets. An efficient monitoring requires the revisit time, defined as the maximum of the time elapsed between successive revisits to targets, to be minimized. Here, we consider the problem of determining UAV routes that lead to the minimum revisit time. The problem is NP-hard, and its computational difficulty increases with the fuel capacity of the UAV. We develop an algorithm to construct near-optimal solutions to the problem quickly when the fuel capacity exceeds a threshold. We also develop lower bounds to the optimal revisit time and use these bounds to demonstrate (through numerical simulations) that the constructed solutions are, on an average, at most 0.01% away from the optimum.

42 ENGINEERING↗
DOE OSTI2020

Artificial illumination identification from an unmanned aerial vehicle

Artificial illumination identification within images is a useful tool for many applications. Performing such identification allows for an estimation of the illumination source spectrum, which in turn can be used for additional applications ranging from spectral detection and exploitation to statistics about nighttime light usage. Illumination identification has been performed in laboratory settings but not from an unmanned aerial vehicle (UAV) platform. Here, we test the feasibility of using a UAV and commercial off-the-shelf multispectral imaging sensor to perform such artificial illumination identification through linear discriminant analysis using nighttime UAV images. The results are very promising, showing source classification accuracies of 83.3%, 92.3%, 100%, and 100% for the incandescent, light-emitting diode, high pressure sodium, and metal halide illumination sources, respectively. We show that the information gained from the source identification can be further used to inform additional analysis, such as spectral identification. The high resolution of UAV imaging techniques combined with the knowledge of the illumination source can lead to better exploitation of such nighttime data for many applications.

42 ENGINEERING↗
DOE OSTI2025

Systems, devices, and methods for millimeter wave communication for unmanned aerial vehicles

Systems, devices, and methods are described for controlling, and communicating with, unmanned aerial vehicles (UAVs) over a millimeter wave (mmWave) communication network established between a base station and the UAVs. A communication system may include one or more unmanned aerial vehicles (UAVs). The communication system may further include one or more base stations including millimeter wave (mmWave) antennas configured to generate control signals to the one or more UAVs over an mmWave communication network.

Bhuyan, Arupjyoti↗
DOE OSTI2023

Grain size estimation in fluvial gravel bars using uncrewed aerial vehicles: A comparison between methods based on imagery and topography

Abstract Grain size assessments are necessary for understanding the various geomorphological, hydrological and ecological processes that occur within rivers. Recent research has shown that the application of Structure‐from‐Motion (SfM) photogrammetry to imagery from uncrewed aerial vehicles (UAVs) shows promise for rapidly characterising grain sizes along rivers in comparison to traditional field‐based methods. Here, we evaluated the applicability of different methods for estimating grain sizes in gravel bars along a study reach in the Olentangy River in Columbus, Ohio. We collected imagery of these gravel bars with a UAV and processed those images with SfM photogrammetry software to produce three‐dimensional point clouds and orthomosaics. Our evaluation compared statistical models calibrated on topographic roughness, which was computed from the point clouds, and to those based on image texture, which was computed from the orthomosaics. Our results showed that statistical models calibrated on image texture were more accurate than those based on topographic roughness. This might be because of site‐specific patterns of grain size, shape and imbrication. Such patterns would have complicated the detection of topographic signatures associated with individual grains. Our work illustrates that UAV‐SfM approaches show potential to be used as an accessible method for characterising surface grain sizes along rivers at higher spatial and temporal resolutions than those provided by traditional methods.

Wong, Tyler↗
DOE OSTI2021

A probabilistic graphical model foundation for enabling predictive digital twins at scale

A unifying mathematical formulation is needed to move from one-off digital twins built through custom implementations to robust digital twin implementations at scale. This work proposes a probabilistic graphical model as a formal mathematical representation of a digital twin and its associated physical asset. We create an abstraction of the asset–twin system as a set of coupled dynamical systems, evolving over time through their respective state spaces and interacting via observed data and control inputs. The formal definition of this coupled system as a probabilistic graphical model enables us to draw upon well-established theory and methods from Bayesian statistics, dynamical systems and control theory. The declarative and general nature of the proposed digital twin model make it rigorous yet flexible, enabling its application at scale in a diverse range of application areas. Here, we demonstrate how the model is instantiated to enable a structural digital twin of an unmanned aerial vehicle (UAV). The digital twin is calibrated using experimental data from a physical UAV asset. Its use in dynamic decision-making is then illustrated in a synthetic example where the UAV undergoes an in-flight damage event and the digital twin is dynamically updated using sensor data. The graphical model foundation ensures that the digital twin calibration and updating process is principled, unified and able to scale to an entire fleet of digital twins.

42 ENGINEERING↗
DOE OSTI2022

Deep Convolutional Neural Networks Exploit High-Spatial- and -Temporal-Resolution Aerial Imagery to Phenotype Key Traits in Miscanthus

Miscanthus is one of the most promising perennial crops for bioenergy production, with high yield potential and a low environmental footprint. The increasing interest in this crop requires accelerated selection and the development of new screening techniques. New analytical methods that are more accurate and less labor-intensive are needed to better characterize the effects of genetics and the environment on key traits under field conditions. We used persistent multispectral and photogrammetric UAV time-series imagery collected 10 times over the season, together with ground-truth data for thousands of Miscanthus genotypes, to determine the flowering time, culm length, and biomass yield traits. We compared the performance of convolutional neural network (CNN) architectures that used image data from single dates (2D-spatial) versus the integration of multiple dates by 3D-spatiotemporal architectures. The ability of UAV-based remote sensing to rapidly and non-destructively assess large-scale genetic variation in flowering time, height, and biomass production was improved through the use of 3D-spatiotemporal CNN architectures versus 2D-spatial CNN architectures. The performance gains of the best 3D-spatiotemporal analyses compared to the best 2D-spatial architectures manifested in up to 23% improvements in R2, 17% reductions in RMSE, and 20% reductions in MAE. The integration of photogrammetric and spectral features with 3D architectures was crucial to the improved assessment of all traits. In conclusion, our findings demonstrate that the integration of high-spatiotemporal-resolution UAV imagery with 3D-CNNs enables more accurate monitoring of the dynamics of key phenological and yield-related crop traits. This is especially valuable in highly productive, perennial grass crops such as Miscanthus, where in-field phenotyping is especially challenging and traditionally limits the rate of crop improvement through breeding.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Deep Learning and Photogrammetric Reconstruction for Automated Crack Detection and Dimensional Measurement in Mining Operations

Surface crack detection and dimensional measurement at active mining sites present significant safety and operational challenges. Manual inspection methods are labor-intensive, spatially incomplete, and expose personnel to hazardous environments, while existing automated approaches have been developed primarily for concrete civil infrastructure and have not been validated on the complex, variable surfaces characteristic of mining environments. This dissertation presents an automated pipeline that integrates deep learning semantic segmentation with Structure-from-Motion photogrammetry to detect surface cracks and measure their aperture, length, and vertical displacement from standard RGB imagery acquired during routine Uncrewed Aerial Vehicle (UAV) survey operations, without requiring additional sensor hardware or manual measurement. The pipeline combines a U-Net architecture with an EfficientNet-B0 encoder, pretrained on the SDNET2018 concrete crack dataset and fine-tuned on a mining-specific dataset spanning laboratory concrete specimens, coal refuse impoundment embankments, and post-blast limestone quarry benches. Photogrammetric reconstruction is performed using COLMAP Structure-from-Motion and Multi-View Stereo, with crack segmentation masks projected into the reconstructed point cloud to enable three-dimensional vertical displacement measurement through local plane fitting and bimodal surface detection. The pipeline was validated across 36 controlled laboratory specimens at three imaging distances and four vertical displacement levels, achieving aperture measurement RMSE of 0.047 cm and R² of 0.954, and vertical displacement RMSE of 0.140 cm and R² of 0.966, against independent caliper measurements. Field application at a coal refuse impoundment in southwestern Pennsylvania detected 71 crack components across the embankment crest, with a dominant longitudinal crack exhibiting aperture values reaching 28 cm and a 95th percentile vertical displacement of 35.53 cm, consistent in magnitude and spatial distribution with simultaneously acquired LiDAR-derived estimates. Application across four post-blast limestone quarry bench datasets in California successfully characterized blast-induced fracture networks at ground sampling distances ranging from 0.59 to 1.23 cm/pixel, with detected crack geometries physically consistent with observable surface conditions at each site. The results demonstrate that deep learning-based crack detection and photogrammetric measurement can be integrated into routine UAV inspection workflows at mining sites, providing repeatable, scalable, and quantitative crack characterization across surface types, crack scales, and displacement magnitudes not previously addressed in the literature. The pipeline requires no dedicated surveying equipment beyond the UAV platforms already deployed at mine sites for survey and monitoring purposes, supporting practical adoption within existing operational workflows.

Crack detection, Dimensional Measurement↗
DOE OSTI2023

Site Selection for Field Testing of a Marine Hydrokinetic Turbine Platform to Serve as a Floating Unmanned Mobile Recharging Station for Aerial Drones

Abstract Expanding applications of unmanned aerial vehicles (UAVs) in coastal areas suggests a need for stations along or close to the coast where the UAV batteries can be easily recharged. A small-scale low flow marine current turbine in support of a floating autonomous recharge station for small UAVs has been designed and assembled at Florida Atlantic University and is being prepared for field testing. Surveys of identified test sites in the Intracoastal Waterways and at open ocean locations are being conducted to determine their suitability in meeting resource, system design and permitting requirements. A sensor platform has been developed for measuring local currents at the identified sites in support of resource characterization. Two out of the eight sites surveyed in the Intracoastal Waterways are found to meet the field-testing requirements for current resource, water depth, and sea bottom conditions. Planned field testing will include parametric characterization studies of the performance of the current turbine for a range of turbine blade configurations, current speeds, turbine wheel submergence levels, and test site location (channeled flow vs open ocean flow).

McKinney, Adriana Lynell↗
DOE OSTI2021

Method and system for determining a geographical location of an unmanned aerial vehicle flown in proximity to a power grid

A method for determining geolocation of a UAV near a power grid includes detecting, via a transceiver, a carrier signal transmitted from a first grid node to identify the node's fixed geolocation. A response signal may be transmitted from a second grid node in response to the carrier signal to identify a fixed geolocation of the second grid node, or the UAV may process the carrier signal. A processor determines time-of-flight of the carrier signal, e.g., using the response signal, and derives the UAV's geolocation using the time-of-flight. Determining time-of-flight may include referencing a lookup table indexed by time-of-arrival at the transceiver of the modulated carrier and response signals. A timestamp may indicate time-of-transmission of the carrier and response signals, respectively. Deriving geolocation may include subtracting time-of-transmission of the response signal from that of the carrier signal. A system includes the processor and transceiver.

Moore, Andrew J.↗
DOE OSTI2025

Heliostat optical error inspection with polarimetric imaging drone

On a Concentrated Solar Power (CSP) field, optical errors have significant impacts on the collection efficiency of heliostats. Fast, cost-effective, labor-efficient, and non-intrusive autonomous field inspection remains a challenge. Approaches using imaging drone, i.e., Unmanned Aerial Vehicle (UAV) system integrated with high resolution visible imaging sensors, have been developed to address these challenges; however, these approaches are often limited by insufficient imaging contrast. Here, in this study, we report a polarimetry-based method with a polarization imaging system integrated on UAV to enhance imaging contrast for in-situ detection of heliostat mirrors without interrupting field operation. We developed an optical model for skylight polarization pattern to simulate the polarization images of heliostat mirrors and obtained optimized waypoints for polarimetric imaging drone flight path to capture images with enhanced contrast. The polarimetric imaging-based method improved the success rate of edge detections in scenarios which were challenging for mirror edge detection with conventional imaging sensors. We have performed field tests to achieve significantly enhanced heliostat edge detection success rate and investigate the feasibility of integrating polarimetric imaging method with existing imaging-based heliostat inspection methods, i.e., Polarimetric Imaging Heliostat Inspection Method (PIHIM). Our preliminary field test results suggest that the PIHIM hold the promise to enable sufficient imaging contrast for real-time autonomous imaging and detection of heliostat field, thus suitable for non-interruptive fast CSP field inspection during its operation.

CSP Field↗