Search NASA⌕ Search

SEARCH · Search NASA

Results for “Unity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Reference Natural Gas Flames at Nominally Autoignitive Engine-Relevant Conditions

Laminar natural gas flames are investigated at engine-relevant thermochemical conditions where the ignition delay time r is short due to very high ambient temperatures and pressures. At these conditions, it is not possible to measure or calculate well-defined values for the laminar flame speed S-l, laminar flame thickness delta(l), and laminar flame time scale tau(l) = delta(l)/S-l due to the explosive thermochemical state. Here, the corresponding reference values, S-R, delta(R), and tau(R) = S-R/S-R, that account for the effects of autoignition, are numerically estimated to investigate the enhancement of flame propagation, and the competition with autoignition that arises under nominally autoignitive conditions (characterised here by the number tau/tau(R)). Large values of tau/tau(R) indicate that autoignition is unimportant, values near or below unity indicate that flame propagation is not possible, and intermediate values indicate that a combination of both flame propagation and autoignition may be important, depending upon factors such as device geometry, turbulence, stratification, et cetera. The reference quantities are presented for a wide range of temperatures, equivalence ratios, pressures, and hydrogen concentrations, which includes conditions relevant to stationary gas turbine reheat burners and boosted spark ignition engines. It is demonstrated that the transition from flame propagation to autoignition is only dependent on residence time, when the results are non-dimensionalised by the reference values. The temporal evolution of the reference values are also reported for a modelled boosted SI engine. It is shown that the nominally autoignitive conditions enhance flame propagation, which may be an ameliorating factor for the onset of engine knock. The calculations are performed using a recently-developed, detailed 177 species mechanism for C0-C3 chemistry that is derived from theoretical chemistry and is suitable for a wide range of thermochemical conditions as it is not tuned or optimised for a particular operating condition. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

autoignition↗
DOE OSTI2023

Correlating viscosity and die swell in 3D printing of polyphenylsulfone: A thermo-mechanical optimization modus operandi

Additive manufacturing (AM) of polyphenylsulfone (PPSU), an amorphous high-performance polymer (HPP), has shown promise in exhibiting structural integrity for many applications. With thermoplastic material extrusion 3D printing, parts consisting of layered melts exhibited voids, where the adhesion quality and void size depend on the processing parameters implemented during printing. However, the structure-process-property (SPP) relationships between the thermal properties and rheological and mechanical behavior of AM PPSU are poorly understood. Here, in this study, a comprehensive analysis of the thermal, thermo-mechanical, and layer-by-layer build-up of PPSU is investigated and correlated with viscosity and extrudate die swell behavior with void fraction volume as confirmed by high-resolution x-ray computed tomography (XCT). Gas chromatography–mass spectrometry (GC–MS) pyrolysis confirmed PPSU composition and degradation at 480 °C, consistent with thermo-gravimetric analysis TGA. A 141% difference in viscosity was observed when processing temperatures increased from 350 °C to 400 °C. Likewise, extrudate die swell decreased with increasing temperatures, resulting in a 17% difference. Tensile and compressive properties confirmed that higher extruding temperatures resulted in lower porosity and higher mechanical strength. In general, higher extruding temperatures lower the viscosity to allow for stronger cohesion between layers; however, increasing the temperature too high results in a below unity extrudate die swell, reducing mechanical properties. Therefore, to optimize the mechanical integrity of 3D printed amorphous PPSU parts, an increase in the viscosity, near unity of the extrudate die swell, and tempered extrusion temperature are needed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Towards the distributed burning regime in turbulent premixed flames

Three-dimensional numerical simulations of canonical statistically steady, statistically planar turbulent flames have been used in an attempt to produce distributed burning in lean methane and hydrogen flames. Dilatation across the flame means that extremely large Karlovitz numbers are required; even at the extreme levels of turbulence studied (up to a Karlovitz number of 8767) distributed burning was only achieved in the hydrogen case. In this case, turbulence was found to broaden the reaction zone visually by around an order of magnitude, and thermodiffusive effects (typically present for lean hydrogen flames) were not observed. In the preheat zone, the species compositions differ considerably from those of one-dimensional flames based a number of different transport models (mixture averaged, unity Lewis number and a turbulent eddy viscosity model). The behaviour is a characteristic of turbulence dominating non-unity Lewis number species transport, and the distinct limit is again attributed to dilatation and its effect on the turbulence. Peak local reaction rates are found to be lower in the distributed case than in the lower Karlovitz cases but higher than in the laminar flame, which is attributed to effects that arise from the modified fuel-temperature distribution that results from turbulent mixing dominating low Lewis number thermodiffusive effects. Finally, approaches to achieve distributed burning at realisable conditions are discussed; factors that increase the likelihood of realising distributed burning are higher pressure, lower equivalence ratio, higher Lewis number and lower reactant temperature.

42 ENGINEERING↗
DOE OSTI2022

Low-Reynolds-number oscillating boundary layers on adiabatic slopes

We investigate the instabilities and transition mechanisms of Boussinesq stratified boundary layers on sloping boundaries when subjected to oscillatory body forcing parallel to the slope. We examine idealized forms of boundary layers on hydraulically smooth abyssal slopes in tranquil mid- to low-latitude regions, where low-wavenumber internal tides gently heave isopycnals up and down adiabatic slopes in the absence of mean flows, high-wavenumber internal tides, shelf breaks, resonant tide–bathymetry interactions (critical slopes) and other phenomena associated with turbulence ‘hot spots’. In non-rotating low-Reynolds-number flow, increased stratification on the downslope phase has a relaminarizing effect, while on the upslope phase we find transition-to-turbulence pathways arise from shear production triggered by gravitational instabilities. When rotation is significant (low slope Burger numbers) we find that boundary layer turbulence is sustained throughout the oscillation period, resembling stratified Stokes–Ekman layer turbulence. Simulation results suggest that oscillating boundary layers on smooth slopes at low Reynolds number ($Re\leqslant 840$), unity Prandtl number and slope Burger numbers greater than unity do not cause significant irreversible turbulent buoyancy flux (mixing), and that flat-bottom dissipation rate models derived from the tide amplitude are accurate within an order of magnitude.

42 ENGINEERING↗
DOE OSTI2019

GeI 2 Additive for High Optoelectronic Quality CsPbI 3 Quantum Dots and Their Application in Photovoltaic Devices

Trioctylphosphine (TOP)-based syntheses of CsPbI 3 perovskite quantum dots (QDs) yield unprecedented high photoluminescence quantum yield (PL QY), lower Stokes shifts, and longer carrier lifetimes due to their enhanced crystallinity. This synthetic route relies on a heavily Pb-rich condition or a large Pb:Cs molar ratio in precursor solution to produce QDs with appropriate stoichiometry as well as to guarantee a good colloidal stability. The high Pb condition is achieved by a high concentration of PbI 2 prepared in TOP. Here we find such Pb-rich strategies can be avoided by providing additional iodine ions using other metal halide salts. In particular GeI 2 , which contrary to PbI 2 , readily dissolves in TOP. CsPbI 3 QDs prepared using PbI 2 /GeI 2 combination show near-unity PL QY and improved chemical stability compared to the previous synthetic route. Furthermore, we find no sign of Ge incorporation in the QDs (compositionally or energetically). The ensuing QD solar cells deliver power conversion efficiency of 12.15% and retain 85% of its peak performance after storage over 90 days. The PbI 2 /GeI 2 dual-source iodine synthetic approach presented here represents a more rational and robust route to high-quality CsPbI 3 QDs. to guarantee a good colloidal stability. The high Pb condition is achieved by a high concentration of PbI2 prepared in TOP. Here we find such Pb-rich strategies can be avoided by providing additional iodine ions using other metal halide salts. In particular GeI 2 , which contrary to PbI 2 , readily dissolves in TOP. CsPbI 3 QDs prepared using PbI 2 /GeI 2 combination show near-unity PL QY and improved chemical stability compared to the previous synthetic route. Furthermore, we find no sign of Ge incorporation in the QDs (compositionally or energetically). The ensuing QD solar cells deliver power conversion efficiency of 12.15% and retain 85% of its peak performance after storage over 90 days. The PbI 2 /GeI 2 dual-source iodine synthetic approach presented here represents a more rational and robust route to high-quality CsPbI 3 QDs.

14 SOLAR ENERGY↗
DOE OSTI2019

Mechanistic Exploration of Dodecanethiol-Treated Colloidal CsPbBr 3 Nanocrystals with Photoluminescence Quantum Yields Reaching Near 100%

Metal halide perovskite nanocrystals (NCs) are attractive materials for optoelectronics. However, further improvements in stability, reproducibility, and photoluminescence quantum yield (Φ PL ) are essential for enabling future applications. Inadequate surface passivation is a major cause of instability, irreproducibility, and less than unity Φ PL . Herein, we probe the influence of multiple ligand binding groups on the colloidal stability and Φ PL of CsPbBr 3 nanocrystals (NCs). Here, we find that post-synthetic treatment with dodecanethiol reproducibly yields highly stable NCs with near-unity Φ PL for a range of synthetic conditions and initial Φ PL of the as-synthesized NCs. A mechanistic investigation shows that thiol addition leads to thioether formation via the thiol–ene reaction with octadecene, oleic acid, and oleylamine. Both thiolates and thioethers are suspected to bind to undercoordinated Pb atoms on the NC surfaces, and this surface binding can be rapidly accelerated through exposure to blue or UV light. Furthermore, we show that metallic Pb nanoparticles appear in many batches of synthesized CsPbBr 3 NCs and that dodecanethiol addition eliminates these metallic Pb particles.

14 SOLAR ENERGY↗
DOE OSTI2024

Resonant Multiple-Phonon Absorption Causes Efficient Anti-Stokes Photoluminescence in CsPbBr 3 Nanocrystals

Lead halide perovskite nanocrystals, such as CsPbBr 3 , exhibit efficient photoluminescence (PL) up-conversion, also referred to as anti-Stokes photoluminescence (ASPL). This is a phenomenon where irradiating nanocrystals up to 100 meV below gap results in higher energy band edge emission. Most surprising is that ASPL efficiencies approach unity and involve single-photon interactions with multiple phonons. This is unexpected given the statistically disfavored nature of multiple-phonon absorption. Here, in this study, we report and rationalize near-unity anti-Stokes photoluminescence efficiencies in CsPbBr 3 nanocrystals and attribute them to resonant multiple-phonon absorption by polarons. The theory explains paradoxically large efficiencies for intrinsically disfavored, multiple-phonon-assisted ASPL in nanocrystals. Moreover, the developed microscopic mechanism has immediate and important implications for applications of ASPL toward condensed phase optical refrigeration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Particle-in-cell modeling of plasma jet merging in the large-Hall-parameter regime

The merging process of magnetized plasma jets with parameters relevant to the plasma-jet-driven magneto-inertial fusion (PJMIF) design and the plasma liner experiment (PLX) is modeled by fully kinetic particle-in-cell (PIC) simulations in one and two spatial dimensions. Here, the modified two-stream instability is identified to be the main mechanism responsible for stopping the plasma jets and preventing species interpenetration. The electron and ion Hall parameters of the merged plasma are greater than unity, and the plasma β is close to unity, which is the desired characteristic of planned experiments at PLX. Our 2D PIC simulations validate the results of the radiation magneto-hydrodynamics code FLASH, which will be the primary tool for modeling various stages of future PJMIF experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Impact of divertor material on neutral recycling and discharge fueling in DIII-D

We report that experiments with the lower divertor of DIII-D during the Metal Rings Campaign (MRC) show that the fraction F of atomic D in the total recycling flux is material-dependent and varies through the ELM cycle, which may affect divertor fueling. Between ELMs, F C ~ 10% and FW ~ 40%, consistent with expectations if all atomic recycling is due to reflections. During ELMs, F C increases to 50% and F W to 60%. In contrast, the total D recycling coefficient including atoms and molecules R stays close to unity near the strike point where the surface is saturated with D. During ELMs, R can deviate from unity, increasing during high energy ELM-ion deposition (net D release) and decreasing at the end of the ELM which leads to ability of the target to trap the ELM-deposited D. The increase of R > 1 in response to an increase in ion impact energy Ei has been studied with small divertor target samples using Divertor Materials Evaluation System (DiMES). An electrostatic bias was applied to DiMES to change E i by 90 eV. On all studied materials including C, Mo, uncoated and W-coated TZM (>99% Mo, Ti, and Zr alloy), W, and W fuzz, an increase of E i transiently increased the D yield (and R) by ~10%. On C there was also an increase in the molecular D 2 yield, probably due to ion-induced D 2 desorption. Despite the measured increase in F on W compared to C, attached H-mode shots with OSP on W during MRC did not demonstrate a higher pedestal density. About 8% increase in the edge density could be seen only in attached L-mode scenarios. The difference can be explained by higher D trapping in the divertor and lower divertor fueling efficiency in H- versus L-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

HSC-XXL: Baryon budget of the 136 XXL groups and clusters

Abstract We present our determination of the baryon budget for an X-ray-selected XXL sample of 136 galaxy groups and clusters spanning nearly two orders of magnitude in mass (M500 ∼ 1013–1015 M⊙) and the redshift range 0 ≲ z ≲ 1. Our joint analysis is based on the combination of Hyper Suprime-Cam Subaru Strategic Program (HSC-SSP) weak-lensing mass measurements, XXL X-ray gas mass measurements, and HSC and Sloan Digital Sky Survey multiband photometry. We carry out a Bayesian analysis of multivariate mass-scaling relations of gas mass, galaxy stellar mass, stellar mass of brightest cluster galaxies (BCGs), and soft-band X-ray luminosity, by taking into account the intrinsic covariance between cluster properties, selection effect, weak-lensing mass calibration, and observational error covariance matrix. The mass-dependent slope of the gas mass–total mass (M500) relation is found to be $1.29_{-0.10}^{+0.16}$, which is steeper than the self-similar prediction of unity, whereas the slope of the stellar mass–total mass relation is shallower than unity; $0.85_{-0.09}^{+0.12}$. The BCG stellar mass weakly depends on cluster mass with a slope of $0.49_{-0.10}^{+0.11}$. The baryon, gas mass, and stellar mass fractions as a function of M500 agree with the results from numerical simulations and previous observations. We successfully constrain the full intrinsic covariance of the baryonic contents. The BCG stellar mass shows the larger intrinsic scatter at a given halo total mass, followed in order by stellar mass and gas mass. We find a significant positive intrinsic correlation coefficient between total (and satellite) stellar mass and BCG stellar mass and no evidence for intrinsic correlation between gas mass and stellar mass. All the baryonic components show no redshift evolution.

Akino, Daichi↗
DOE OSTI2026

Observation of Suppressed Charged-Particle Production in Ultrarelativistic Oxygen-Oxygen Collisions

A hot and dense state of nuclear matter, known as the quark-gluon plasma, is created in collisions of ultrarelativistic heavy nuclei. Highly energetic quarks and gluons, collectively referred to as partons, lose energy as they travel through this matter, leading to suppressed production of particles with large transverse momenta (𝑝 T ). Conversely, high-𝑝 T particle suppression has not been seen in proton-lead collisions, raising questions regarding the minimum system size required to observe parton energy loss. Oxygen-oxygen (OO) collisions examine a region of effective system size that lies between these two extreme cases. The CMS detector at the CERN LHC has been used to quantify charged-particle production in inclusive OO collisions for the first time via measurements of the nuclear modification factor (𝑅 AA ). The 𝑅 AA is derived by comparing particle production to expectations based on proton-proton (𝑝⁢𝑝) data and has a value of unity in the absence of nuclear effects. The data for OO and 𝑝⁢𝑝 collisions at a nucleon-nucleon center-of-mass energy $\sqrt{s_{NN}}$ = 5.36 TeV correspond to integrated luminosities of 6.1 nb −1 and 1.02 pb −1 , respectively. The 𝑅 AA is below unity with a minimum of 0.69 ± 0.04 around 𝑝 T = 6 GeV. The data exhibit better agreement with theoretical models incorporating parton energy loss as compared to baseline models without energy loss.

FOS: Physical sciences↗
DOE OSTI2026

High-efficiency, high-fidelity charge initialization of shallow nitrogen-vacancy centers in diamond

Nitrogen-vacancy (N-𝑉) centers in diamond exhibit long spin-coherence times, optical initialization, and optical-spin readout under ambient conditions, making them excellent quantum sensors. However, the conventional scheme for charge-state initialization based on off-resonant green excitation results in significant state-preparation errors, typically around 30%. One method for improving charge-state initialization fidelity is to use multicolor excitation, which has been demonstrated to achieve a near-unity preparation fidelity for bulk N-𝑉 centers by using a few milliseconds of near-infrared (NIR) (5-mW) and green (10-μ⁢W) excitation. The translation of such schemes to N-𝑉 centers near the diamond surface with higher-efficiency optical pumping would enable new applications in nanoscale sensing. Here, we demonstrate a protocol for efficient charge initialization of shallow N-𝑉 centers between 5 nm and 15 nm from the diamond surface. By carefully studying the charge dynamics of shallow N-𝑉 centers, we identify a region of parameter space that allows for near-unity (95%) charge initialization within 300 μ⁢s of NIR (905-nm, 1-mW) and green (520-nm, 10-μ⁢W) excitation. The time to 90% charge initialization can be as fast as 10 μ⁢s for 4 mW of NIR and 39 μ⁢W of green illumination. This fast, efficient charge initialization protocol will especially benefit nanoscale sensing applications in which state-preparation errors currently prohibit scaling, such as measuring higher-order multipoint correlators.

infrared techniques↗
DOE OSTI2024

Three-dimensional modeling of a plasma in a strong azimuthal magnetic field

Three-dimensional magnetohydrodynamic (MHD) simulations are able to model the generation of disc-shaped plasma, driven by laser ablation from a current carrying rod in a pulsed-power machine producing azimuthal magnetic fields of 2–3 MG. The plasma at such extreme conditions is unique in that the parameter space for the plasma β and Hall parameter χ transition from below unity to greater than unity at different stages of the plasma generation. In simulations, the formation of the plasma disc in the azimuthal direction, is driven by heat flux from the laser spot and depends on the set of transport coefficients used in simulations. The most recent set of transport coefficients leads to the formation of plasma ejecta at the back end of the rod, that qualitatively matches experiments. Specifically, the cross-gradient Nernst effect, which twists magnetic field, is shown to have a large effect on the shape of the back end ejecta. In the direction along the axis of the rod there is propagation of perturbations from the disc as observed in experiments. In simulations the period of temperature perturbations is in good agreement with experimental results. Furthermore, an instability due to coupling of heat flux and the magnetic field advection provides a possible explanation for perturbation growth along the axis of the rod, and the instability growth rate is consistent with experimental results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Energy Principles of Scientific Breakeven in an Inertial Fusion Experiment

Fusion “scientific breakeven” (i.e., unity target gain G target , total fusion energy out > laser energy input) has been achieved for the first time (here, G target ∼ 1.5 ). This Letter reports on the physics principles of the design changes that led to the first controlled fusion experiment, using laser indirect drive, on the National Ignition Facility to produce target gain greater than unity and exceeded the previously obtained conditions needed for ignition by the Lawson criterion. Key elements of the success came from reducing “coast time” (the time duration between the end of the laser pulse and implosion peak compression) and maximizing the internal energy delivered to the “hot spot” (the yield producing part of the fusion fuel). The link between coast time and maximally efficient conversion of kinetic energy into internal energy is explained. The energetics consequences of asymmetry and hydrodynamic-induced mixing were part of high-yield big radius implosion design experimental and design strategy. Herein, it is shown how asymmetry and mixing consolidate into one key relationship. It is shown that mixing distills into a kinetic energy cost similar to the impact of implosion asymmetry, shifting the threshold for ignition to higher implosion kinetic energy—a factor not normally included in most statements of the generalized Lawson criterion, but the key needed modifications clearly emerge. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Control of ternary alloy composition during remote epitaxy on graphene

Understanding the sticking coefficient σ, i.e., the probability of an adatom sticking to a surface, is essential for controlling the stoichiometry during epitaxial film growth. However, σ on monolayer graphene-covered surfaces and its impact on remote epitaxy are not understood. Here, using molecular-beam epitaxial growth of the magnetic shape memory alloy Ni 2 MnGa, we show that the sticking coefficients for metals on graphene-covered MgO (001) are less than one and are temperature and element dependent, as revealed by ion backscattering spectrometry and energy-dispersive x-ray spectroscopy. This lies in stark contrast with most transition metals sticking on semiconductor and oxide substrates, for which σ is near unity at typical growth temperatures (T < 800°C). By initiating growth below 400°C, where the sticking coefficients are closer to unity and wetting on the graphene surface is improved, we demonstrate the epitaxy of Ni 2 MnGa films with controlled stoichiometry that can be exfoliated to produce freestanding membranes. Straining these membranes tunes the magnetic coercive field. Finally, our results provide a route to synthesize membranes with complex stoichiometries whose properties can be manipulated via strain.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ high-temperature X-ray diffraction study of Sc-doped titanium oxide nanocrystallites

Titanium dioxide is an inexpensive wide-gap highly ionic semiconductor with striking photocatalytic capabilities in several heterogeneous photoredox reactions. A small crystal size is desirable to maximize the surface area, since photocatalytic reactions occur at the surface of a photocatalyst. Presented in this work are the synthesis and microstructural characterization of 4 at.% Sc-doped TiO 2 (4SDT) prepared by water-based co-precipitation. The crystal structure of 4SDT was examined via in situ high-temperature powder X-ray diffraction experiments from 25 to 1200°C. Rietveld analysis revealed single-phase anatase up to 875°C, while at 900°C the anatase-to-rutile phase transformation occurred and at higher temperatures additional reflections of Sc-rich phases (Sc 2 TiO 5 from 975°C and Ti 3 Sc 4 O 12 or Sc 2 O 3 at 1200°C) were observed. Debye function analysis (DFA) was applied to model the total scattering pattern directly in reciprocal space, allowing the reconstruction of Ti vacancies. Both Rietveld and DFA methods were applied to estimate the nanocrystallite size and shape with consistent growth in crystallite size with temperature: an ellipsoid shape with equatorial ~4.7 nm / axial (001) ~6.9 nm at 25°C to equatorial ~27.9 nm / axial (001) ~39.6 nm at 900°C refined by Rietveld analysis, versus a cylinder shape with D a , b = 4.3 nm and size dispersion σ ab = 1.5 nm, L c = 4.9 nm and σ c = 2.3 nm at 25°C to D a , b = 21.4 nm, σ ab = 8.3 nm, L c = 23.9 and σ c = 10.9 nm at 900°C estimated by DFA. The microstructural changes obtained by Rietveld and DFA methods were supported by high-resolution transmission electron microscopy image analysis, as well as by the less direct nitrogen sorption techniques that provide information on the size of non-agglomerated and dense particles. The Ti site-occupancy factor showed a linear increase from 0.6–0.8 at 25°C to unity at 900°C for anatase, and from ~0.7 at 900°C to unity at 1200°C for rutile, via Rietveld analysis and DFA.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling and Control of Cascaded Bridgeless Multilevel Rectifier Under Unbalanced Load Conditions

The goal of this project is to model and control a novel unidirectional cascaded multilevel bridgeless rectifier as an active front end in medium and high voltage applications. This topology has many advantages over a conventional cascaded H-bridge rectifier, such as lower implementation cost, higher reliability, and greater flexibility with similar power quality.The steady-state mathematical model is used to develop a method for the voltage balancing of dc cells. Power factor analysis is discussed to achieve unity power factor using fully controlled hbridge cells. Power loss, efficiency, and cost comparison studies between the traditional cascaded H-Bridge converter and the proposed bridgeless converter demonstrate the advantages. A novel control strategy is proposed to achieve dc voltage balancing, fast and robust grid synchronization and power factor correction under unbalanced load conditions. Simulation and experimental results validate the models and control method.

Cascaded Bridgeless Rectifier, Power factor analys↗