Search NASA⌕ Search

SEARCH · Search NASA

Results for “WAVEGUIDE RADIATOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

79 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Design of a finline antenna for current drive in TST-2

A novel “finline” antenna was designed to excite lower-hybrid waves (LHWs) for plasma current drive at 2.45 GHz in the TST-2 spherical tokamak. A periodic fin array acts as a transmission line for electromagnetic surface waves. Cold tests confirmed propagation of the electromagnetic surface wave on the fin array which was dominantly Transverse Magnetic (TM). Unlike the conventional waveguide array “grill” antenna, the finline antenna requires only two ports to feed all the elements, and calculations show that there is little reflection regardless of the plasma conditions in front of the antenna. Characteristics of the microwave transmission on the fin array were investigated using a three-dimensional full-wave simulation and the fin geometry was tuned to achieve the desired refractive index. Coupling to LHWs under typical TST-2 scrape-off layer conditions was confirmed by the simulation. Finally, to demonstrate LHW excitation, the finline antenna was energized in the presence of a plasma generated by another 200 MHz LH antenna. The x-ray radiation showed strong enhancement during the finline antenna pulse which indicated successful generation of fast electrons by LHWs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Numerical simulation of dispersion and nonlinear characteristics of microstructured silica fibres with a thin suspended core in a wide range of their parameters

Dispersion and nonlinear characteristics of microstructured silica fibres with a thin suspended core surrounded by three, four or six air holes have been studied theoretically in the wavelength range 1 – 2 μm. It has been shown that, owing to strong fundamental mode confinement near the core, the Kerr nonlinearity coefficient can exceed the nonlinearity coefficient of standard telecom fibre SMF28e by two orders of magnitude. The large waveguide contribution allows for effective group velocity dispersion management. Estimates are presented that demonstrate the feasibility of using suspended core fibre exhibiting Kerr nonlinearity for generating non-classical light: a state with squeezed quantum fluctuations in one of the quadrature components of a cw laser signal at a wavelength near 1.55 μm. (paper)

36 MATERIALS SCIENCE↗
DOE OSTI2023

Polariton Condensation in Gap-Confined States of Photonic Crystal Waveguides

Here, the development of patterned multiquantum well heterostructures in GaAs/AlGaAs waveguides has recently made it possible to achieve exciton-polariton condensation in a topologically protected bound state in the continuum (BIC). Polariton condensation was shown to occur above a saddle point of the two-dimensional polariton dispersion in a one-dimensional photonic crystal waveguide. A rigorous analysis of the condensation phenomenon in these systems, as well as the role of the BIC, is still missing. In the present Letter, we theoretically and experimentally fill this gap by showing that polariton confinement resulting from the negative effective mass and the photonic energy gap in the dispersion play a key role in enhancing the relaxation toward the condensed state. In fact, our results show that low-threshold polariton condensation is achieved within the effective trap created by the exciting laser spot, regardless of whether the resulting confined mode is long-lived (polariton BIC) or short-lived (lossy mode). In both cases, the spatial quantization of the polariton condensate and the threshold differences associated to the corresponding state lifetime are measured and characterized. For a given negative mass, a slightly lower condensation threshold from the polariton BIC mode is found and associated to its reduced radiative losses, as compared to the lossy one.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Demonstration of Microwave Resonant Cavity Transducer Performance in Fluid Flow Sensing: Development of Sensor Performance Model of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave cavity-based transducer for in-core high-temperature fluid flow sensing in molten salt cooled reactors (MSCR) and sodium fast reactors (SFR). This sensor is a hollow metallic cylindrical cavity. The principle of sensing consists of making one wall of the cylindrical cavity flexible enough so that dynamic pressure, which is proportional to fluid velocity, will cause membrane deflection. Membrane deflection causes cavity volume change, which leads to a shift in the resonant frequency. To validate sensor physics, we have performed proof-of-principle test of flow sensing in water. For this test, we have developed a cylindrical resonator for K-band, which was machined from brass. The cavity was excited through WR-42 waveguide through a subwavelength hole on the side of the wall of the cylinder. To increase the spectral signal visibility, we developed a signal processing method for baseline subtraction. A flow loop for proof-of-principle test of transducer performance in water was assembled. A commercial flow meter was installed in the loop for reference measurements. Cylindrical cavity was excited in the TEM 011 mode with resonant frequency f ≈ 17.8GHz. Frequency shift of cavity spectral response was obtained by gradually increasing water flow rate from 0 to 60gpm. Corresponding monotonic increase of resonant frequency shift by several MHz was observed.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

First Annual Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing: Development of Sensor Performance Model of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave cavity-based transducer for in-core high-temperature fluid flow sensing in molten salt cooled reactors (MSCR) and sodium fast reactors (SFR). This sensor is a hollow metallic cylindrical cavity, which can be fabricated from stainless steel, and as such is expected to be resilient to radiation, high temperature and corrosive environment of MSCR and SFR. The principle of sensing consists of making one wall of the cylindrical cavity flexible enough so that dynamic pressure, which is proportional to fluid velocity, will cause membrane deflection. Membrane deflection causes cavity volume change, which leads to a shift in the resonant frequency. Feasibility of the sensor was initially investigated with analytical derivations and with COMSOL RF Module computer simulations of resonant frequency spectral shift due to uniform load. We also investigated the mechanical integrity of the flowmeter’s membrane through analytical modelling and COMSOL Structural Mechanics Module computer simulations. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the material’s yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure. Using results from models, we have developed an initial design for a microwave K-band sensor. A cylindrical resonator prototype was fabricated from brass for the initial tests. The external dimensions of the cavity are matched to the flange of a standard WR-42 waveguide. Microwave field is coupled into the resonant cavity through a subwavelength-size aperture. A test article was developed consisting of a piping Tee with a bulkhead WR-42 microwave waveguide installed in a leak-proof assembly. A microwave waveguide circulator was installed in the setup to suppress the effect of reflections at the cavity entrance by increasing the isolation between the input and the output port. Preliminary spectral characterization of cavity spectral response was performed with a portable PXIe chassis microwave VNA with a custom GUI. Preliminary dry tests of the transducer response were conducted with a set of calibrated weights. Transducer frequency shift was shown to be monotonically increasing with increasing pressure. The next steps will involve investigation of the transducer performance for water flow sensing.

42 ENGINEERING↗
DOE OSTI2025

Chemical Imaging of Atmospheric Biomass Burning Particles from North American Wildfires

The effects of biomass burning aerosols (BBA) on radiative forcing and cloud formation depend on chemical composition and the internal structures of individual particles within smoke plumes. To improve our understanding of the chemical and physical properties of BBA emitted at different times of the day and their evolution during atmospheric aging, we conducted a study as a part of the Fire Influence on Regional to Global Environments and Air Quality field campaign. Particle samples were collected onboard a research aircraft from smoke plumes from a wildfire in eastern Oregon during late afternoon and nighttime flights on August 28, 2019. A time-resolved aerosol collector was used to collect samples on substrates for offline spectromicroscopic imaging to investigate the single-particle characteristics of BBA particles. Approximately 20,400 individual particles from 10 selected samples were analyzed using computer-controlled scanning electron microscopy coupled with energy-dispersive X-ray microanalysis, revealing their elemental composition, morphology, and viscosity. Elemental microanalysis indicated that aged potassium is likely found in the form of K 2 SO 4 , KNO 3 , and possible K-organic salts. Further chemical speciation and carbon bonding mapping within individual particles were conducted using synchrotron-based scanning transmission X-ray microscopy (STXM) coupled with near edge X-ray absorption fine structure (NEXAFS) spectroscopy. Real-time, water-soluble light absorption measurements were acquired using a particle-into-liquid sampler instrument coupled to a liquid waveguide capillary cell and total organic analyzer. In the late afternoon samples, 65% of the total particle number population consisted entirely of organic components, compared to 46% in the nighttime particles. These differences were attributed to discrepancies in composition at the time of emission and to the daytime condensation and accumulation of photochemically formed secondary organic material on existing BBA particles, a process that halts at night. Microscopy images indicated that particle viscosity was lower in the nighttime particles (<10 1 Pa·s), likely due to increased relative humidity and a higher contribution from hygroscopic inorganic components. The chemical heterogeneity of individual particles was quantified using STXM-derived mixing state parameters. The nature of carbon bonding within individual particles was inferred from the extent of carbon sp 2 hybridization derived from NEXAFS spectra. Average percentages of sp 2 hybridization range between 40% and 60%, with no noticeable differences between late afternoon and nighttime flights. These findings were compared with the online optical properties of both late afternoon and nighttime smoke plumes, providing valuable insights into the complex relationship between chemical composition and optical properties of BBA particles at different times of the day.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Control of wakefield in sub-THz dielectric-lined waveguides using multiple-bunch excitation

Beam-driven wakefield accelerators offer the potential to achieve accelerating fields approaching the sub-GV/m range, paving the way for compact and cost-effective next-generation high-energy colliders. This method typically employs a two-bunch system: a drive bunch that excites an electromagnetic wakefield in a solid-state or plasma medium, and a witness bunch that extracts energy from the wake for acceleration. Our research focuses on two key challenges in wakefield acceleration using structures. First, we investigate strategies to suppress transverse instabilities by employing non-cylindrical geometries that damp dipole modes. Second, we explore methods to precisely terminate the wakefield after the interaction region, thereby improving the efficiency of energy transfer. This paper presents detailed simulation results and the corresponding experimental design developed to validate these concepts. Furthermore, the proposed experiment will be carried out at the Argonne Wakefield Accelerator (AWA) facility, focusing on controlling wakefield duration through tailored drive and witness bunch configurations and evaluating dielectric-lined structures with non-cylindrical cross sections.

43 PARTICLE ACCELERATORS↗