Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND TUNNEL WALL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A panel method procedure for interference assessment in slotted-wall wind tunnels

This paper describes a method for three-dimensional wind tunnel interference assessment developed specifically for slotted-wall tunnels. The method is an adaptation to the assessment problem of a previously published high-order panel method procedure for simulating the flow in slotted-wall tunnel test sections. The method uses a mixed outer boundary condition, primarily a Neumann condition, with measured pressure constraints used to control only those boundary phenomena which can not be specified accurately a priori. Assessment results are illustrated from a calibration test with variations in wall geometry, and from tests of a generic subsonic transport aircraft configuration.

Kemp, William B., Jr.↗
NASA NTRS1991

Description and evaluation of an interference assessment for a slotted-wall wind tunnel

A wind-tunnel interference assessment method applicable to test sections with discrete finite-length wall slots is described. The method is based on high order panel method technology and uses mixed boundary conditions to satisfy both the tunnel geometry and wall pressure distributions measured in the slotted-wall region. Both the test model and its sting support system are represented by distributed singularities. The method yields interference corrections to the model test data as well as surveys through the interference field at arbitrary locations. These results include the equivalent of tunnel Mach calibration, longitudinal pressure gradient, tunnel flow angularity, wall interference, and an inviscid form of sting interference. Alternative results which omit the direct contribution of the sting are also produced. The method was applied to the National Transonic Facility at NASA Langley Research Center for both tunnel calibration tests and tests of two models of subsonic transport configurations.

Kemp, William B., Jr.↗
NASA NTRS1993

Transonic wind tunnel wall interference analysis for the Space Shuttle Launch Vehicle

The AEDC perforated-wall boundary condition has been incorporated into the NASA Ames OVERFLOW code and has been used to calculate the tunnel flow field in the AEDC Aerodynamic Wind Tunnel (16T) over a three-percent model of the Space Shuttle Launch Vehicle. Tunnel flow-field calculations have been performed for two supersonic flow-field conditions, including one near sonic condition. Wall interference assessments and analyses have been performed by making detailed comparisons of the tunnel flow-field calculations with corresponding free-air flow-field calculations and with tunnel data from different scale models. A capability to assess wall interference at low supersonic conditions and to improve data correlations with CFD results by adding the tunnel wall boundary condition is demonstrated.

Martin, F. W., Jr.↗
NASA NTRS1974

The effect of wind tunnel wall interference on the performance of a fan-in-wing VTOL model

A fan-in-wing model with a 1.07-meter span was tested in seven different test sections with cross-sectional areas ranging from 2.2 sq meters to 265 sq meters. The data from the different test sections are compared both with and without correction for wall interference. The results demonstrate that extreme care must be used in interpreting uncorrected VTOL data since the wall interference may be so large as to invalidate even trends in the data. The wall interference is particularly large at the tail, a result which is in agreement with recently published comparisons of flight and large scale wind tunnel data for a propeller-driven deflected-slipstream configuration. The data verify the wall-interference theory even under conditions of extreme interference. A method yields reasonable estimates for the onset of Rae's minimum-speed limit. The rules for choosing model sizes to produce negligible wall effects are considerably in error and permit the use of excessively large models.

Heyson, H. H.↗
NASA NTRS1987

An engineering study of hybrid adaptation of wind tunnel walls for three-dimensional testing

Solid wall tunnels having only upper and lower walls flexing are described. An algorithm for selecting the wall contours for both 2 and 3 dimensional wall flexure is presented and numerical experiments are used to validate its applicability to the general test case of 3 dimensional lifting aircraft models in rectangular cross section wind tunnels. The method requires an initial approximate representation of the model flow field at a given lift with wallls absent. The numerical methods utilized are derived by use of Green's source solutions obtained using the method of images; first order linearized flow theory is employed with Prandtl-Glauert compressibility transformations. Equations are derived for the flexed shape of a simple constant thickness plate wall under the influence of a finite number of jacks in an axial row along the plate centerline. The Green's source methods are developed to provide estimations of residual flow distortion (interferences) with measured wall pressures and wall flow inclinations as inputs.

Brown, Clinton↗
NASA NTRS1989

The effect of the wind tunnel wall boundary layer on the acoustic testing of propellers

An approximation based on the representation of the boundary layer by lamina of uniform flow with suitable interlayer boundary conditions is shown to be accurate, efficient, and compatible with finite element formulations. The approximation has been implemented using existing codes to produce a model for assessing the suitability of the acoustic environment in a wind tunnel for the acoustic testing of propellers. It is found that, with suitable acoustic treatment and with measurements made near the propeller and well removed from the walls, the free field directivity and level can be reproduced with good fidelity.

Eversman, Walter↗
NASA NTRS1986

Adaptive wall wind tunnels: A selected, annotated bibliography

This bibliography, with abstracts, consists of 257 citations arranged in chronological order. Selection of the citations was made for their value to researchers working to solve problems associated with reducing wall interference by the design, development, and operation of adaptive wall test sections. Author, source, and subject indexes are included.

Tuttle, M. H.↗
NASA NTRS1985

Wall-interference assessment in three-dimensional slotted-wall wind tunnels

The development of the slotted tunnel simulator code and lessons learned from its use are summarized. The high order panel method was selected as the basic procedure for aerodynamic computations. The panel singularities are supplemented by line sources to represent discrete wall slots.

Kemp, W. B., Jr.↗
NASA NTRS1989

Residual interference assessment in adaptive wall wind tunnels

A two-variable method is presented which is suitable for on-line calculation of residual interference in airfoil testing in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-M TCT). The method applies the Cauchy's integral formula to the closed contour formed by the contoured top and bottom walls, and the upstream and downstream ends. The measured top and bottom wall pressures and position are used to calculate the correction to the test Mach number and the airfoil angle of attack. Application to specific data obtained in the 0.3-M TCT adaptive wall test section demonstrates the need to assess residual interference to ensure that the desired level of wall streamlining is achieved. A FORTRAN computer program was developed for on-line calculation of the residual corrections during airfoil tests in the 0.3-M TCT.

Murthy, A. V.↗
NASA NTRS1975

Reduction of wind tunnel wall interference by controlled wall flow

An alternate method of testing was developed in which flow through the porous walls of the tunnel was actively controlled so as to approximate free air conditions in the neighborhood of the model during the test. The amount and distribution of the controlled flow through the walls is computed using a potential flow representation of the model based on the measured lift. Theoretical analysis is presented to prove the convergence of the method to free air conditions and to substantiate the general three-dimensional theory of operation when the normal flow distribution is continuous. A two-dimensional tunnel was constructed to evaluate the concept. Results show that substantial reduction of wall interference may be achieved with relatively low values of porosity of actively controlled walls.

Bernstein, S.↗
NASA NTRS1982

Some ideas and opportunities concerning three-dimensional wind-tunnel wall corrections

Opportunities for improving the accuracy and reliability of wall corrections in conventional ventilated test sections are presented. The approach encompasses state-of-the-art technology in transonic computational methods combined with the measurement of tunnel-wall pressures. The objective is to arrive at correction procedures of known, verifiable accuracy that are practical within a production testing environment. It is concluded that: accurate and reliable correction procedures can be developed for cruise-type aerodynamic testing for any wall configuration; passive walls can be optimized for minimal interference for cruise-type aerodynamic testing (tailored slots, variable open area ratio, etc.); monitoring and assessment of noncorrectable interference (buoyancy and curvature in a transonic stream) can be an integral part of a correction procedure; and reasonably good correction procedures can probably be developd for complex flows involving extensive separation and other unpredictable phenomena.

Rubbert, P. E.↗
NASA NTRS1982

Three-dimensional flow studies on a slotted transonic wind tunnel wall

Three-dimensional flow field measurements were made near a transonic slotted wall. Field velocity vectors and static pressure distributions have been obtained. The boundary layer displacement thickness was found to vary in the transverse plane with its maximum at the slot center line but decreased with increasing suction rate through the slot. The boundary layer characteristics were sensitive to the mass transfer through the slot. The projection on the flow field velocity vectors on the transverse plane reveals a vortex-like flow formation. The center of this secondary flow was located nearly at the edge of the wall shear layer and decreased in strength with applied suction. The secondary vortex motion may be attributed to the mean flow skewing, inhomogeneous transverse plane boundary layer and the wall turbulence anisotropy.

Wu, J. M.↗
NASA NTRS1984

Wind tunnel wall interference corrections for aircraft models in the transonic regime

A procedure for the evaluation of wall interference corrections for three-dimensional models is presented. In addition to Mach number and angle-of-attack corrections, the procedure provides an estimate of the accuracy of the corrections. Lift, pitching moment, and pressure measurements near the tunnel walls are required by the correction method. The method is demonstrated by application to an isolated wing model and to a wing-body-tail configuration.

Rizk, M. H.↗
NASA NTRS1984

Wind tunnel wall interference in closed, ventilated and adaptive test sections

A wall interference correction method for closed rectangular test sections was developed which uses measured wall pressures. Measurements with circular discs for blockage and a rectangular wing as a lift generator in a square closed test section validate this method. These measurements are intended to be a basis of comparison for measurements in the same tunnel using ventilated (in these case, slotted) walls. Using the vortex lattice method and homogeneous boundary conditions, calculations were performed which show sufficiently high pressure levels at the walls for correction purposes in test sections with porous walls. In Gottingen, an adaptive test section (which is a deformable rubber tube of 800 mm diameter) was built and a computer program was developed which is able to find the necessary wall adaptation for interference-free measurements in a single step. To check the program prior to the first run, the vortex lattice method was used to calculate wall pressure distributions in the nonadapted test section as input data for the one-step method. Comparison of the pressure distribution in the adapted test section with free-flight data shows nearly perfect agreement. An extension of the computer program can be made to evaluate the remaining interference corrections.

Holst, H.↗
NASA NTRS1984

Asymptotic methods for wind tunnel wall corrections at transonic speed

The effort to develop classical methods to compute wall interference at transonic speeds is outlined. The two-dimensional theory and three-dimensional development are discussed. Also, some numerical application of the two-dimensional work are indicated. The basic advantages of the asymptotic theory are noted.

Malmuth, N. D.↗
NASA NTRS1984

NLR activities in the field of wind tunnel wall interference

Measured field data as a boundary condition for calculating the interference flow field were applied. They are divided into two categories. In the first category, the field data must consist of distributions of a single velocity component, and an accurate estimate of the hypothetical free air contribution of the model to this component is required. The differences between measured values and estimated model contributions are attributed to wall interference and they establish the boundary condition. The associated field data measurements are simple, yet the necessary model representation generally is a serious drawback. The second category requires field data which consist of velocity vector distributions at the price of multicomponent measurements, but at the profit that no information at all is required about the model. In solid wall test sections, the price is reduced to virtually zero but the profit remains.

Smith, J.↗