Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, TAPERED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Basic Pressure Measurements at Transonic Speeds on a Thin 45 deg Sweptback Highly Tapered Wing with Systematic Spanwise Twist Variations

Pressure distributions obtained in the Langley 8-foot transonic pressure tunnel on a thin, highly tapered, twisted, 450 sweptback wing in combination with a body are presented. The wing has a cubic spanwise twist variation from 0 deg. at 10 percent of the semispan to 60 at the tip. The tip is at a lower angle of attack than the root. Tests were made at stagnation pressures of 1.0 and 0.5 atmosphere, at Mach numbers from 0 0.800 to 1.200, and at angles of attack from -4 deg. to 20 deg.

Mugler, John P., Jr.↗
NASA NTRS1959

Effect of Tail Dihedral on Lateral Control Effectiveness at High Subsonic Speeds of Differentially Deflected Horizontal-Tail Surfaces on a Configuration having a Thin Highly Tapered Wing

Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel to determine the effect of tail dihedral on lateral control effectiveness of a complete-model configuration having differentially deflected horizontal-tail surfaces. Limited tests were made to determine the lateral characteristics as well as the longitudinal characteristics in sideslip. The wing had an aspect ratio of 3, a taper ratio of 0.14, 28.80 deg sweep of the quarter-chord line with zero sweep at the 80-percent-chord line, and NACA 65A004 airfoil sections. The test Mach number range extended from 0.60 to 0.92. There are only small variations in the roll effectiveness parameter C(sub iota delta) with negative tail dihedral angle. The tail size used on the test model, however, is perhaps inadequate for providing the roll rates specified by current military requirements at subsonic speeds. The lateral aerodynamic characteristics were essentially constant throughout the range of sideslip angle from 12 deg to -12 deg. A general increase in yawing moment was noted with increased negative dihedral throughout the Mach number range.

Fournier, Paul G.↗
NASA NTRS2019

Evaluation of Wing Load Calibration and Sensing Methods Using Conventional Strain Gages and a Fiber Optic Sensing System Installed on a Straight Tapered Wing

This presentation presents the results from a wing load test in the FLL (Flight Loads Lab). Load calibration techniques for strain gages and fiber optics were compared and contrasted. This presentation has the potential to lead to more research testing at NASA Armstrong in the areas of load calibration technology.

load calibrations↗
NASA NTRS1959

Basic Pressure Measurements at Transonic Speeds on a Thin 45 deg Sweptback Highly Tapered Wing With Systematic Spanwise Twist Variations

Pressure distributions obtained in the Langley 8-foot transonic pressure tunnel on a thin, highly tapered, twisted, 45 deg sweptback wing in combination with a body are presented. The wing has a linear span-wise twist variation from 0 deg at 10 percent of the semispan to 6 deg at the tip. The tip is at a lower angle of attack than the root. Tests were made at stagnation pressures of 1.0 and 0.5 atmosphere, at Mach numbers from 0.800 to 1.200, and at angles of attack from -4 to 12 deg.

Mugler, John P., Jr.↗
NASA NTRS1933

Aerodynamic tests of a low aspect ratio tapered wing with various flaps, for use on tailless airplanes

Wind tunnel tests were made of a model wing having an aspect ratio of 3 and a tapered plan form with a straight trailing edge. The model had the Clark Y airfoil section throughout it's entire span and had no washout, depending on a trailing-edge flap for longitudinal balance and control. The flap had a constant chord and was divided into four equal portions along the span. The tests were made with the entire flap deflected to obtain longitudinal control and balance, and also with the inner portions deflected alone, and with the outer portions deflected alone. It was found that the simple wing with no washout or change of basic section along the span has aerodynamic characteristics well suited for use on tailless airplanes. A higher lift coefficient was obtained with the full-span flap deflected as a unit to give longitudinal balance than was obtained with either the inner or the outer portions of the flap deflected.

Weick, Fred E↗
NASA NTRS1959

Basic Pressure Measurements at Transonic Speeds on a Thin 45 deg Sweptback highly Tapered Wing With Systematic Spanwise Twist Variations

Pressure distributions obtained in the Langley 8-foot transonic pressure tunnel on a thin highly tapered twisted 45 deg sweptback wing-body combination are presented. The wing has a quadratic spanwise twist variation from 0 deg at 10 percent of the semispan to 6 deg at the tip. The tip is at a lower angle of attack than the root. Tests were made at stagnation pressures of both 0.5 and 1.0 atmosphere at Mach numbers from 0.800 to 1.200 through an angle-of-attack range from -4 deg to 20 deg.

Mugler, John P., Jr.↗
NASA NTRS1937

Full Scale Span Load Distribution on a Tapered Wing with Split Flaps of Various Spans

Pressure-distribution tests were conducted in the full-scale wind tunnel on a 2:1 tapered U.S.A. 45 airfoil equipped with 20 percent chord split trailing-edge flaps of various spans. A special installation was employed in the tests utilizing a half-span airfoil mounted vertically above a reflection plane. The airfoil has a constant chord center section and rounded tips and is tapered in thickness from 18 percent c at the root to 9 percent c at the tip. The aerodynamic characteristics, given by the usual dimension less coefficients, are presented graphically as functions of flap span and angle of attack as well as by semispan load diagrams. The results indicate, in general, that only a relatively small increase in the normal-force coefficient is to be expected by extending the flap span of an airfoil-flap combination, similar to the one tested, beyond 70 percent of the wing span.

Parsons, John F↗
NASA NTRS1947

Test Report on Three-and Six-Component Measurements on a Series of Tapered Wings of Small Aspect Ratio (Partial Report: Elliptic Wing)

The report UM No. 1023/1 which presented the results of measurements for a series of trapezoidal wings was the beginning of a series on wings with aspect ratio 1 to 3 and various contours. In report No. 1023/1 the aspect ratio (Lambda = 4/3) remained the same; the tapering was modified. The present report gives the results of the series of elliptic wings. Here the aspect ratio varies from 1 to 2 with the sweepback. The contour is formed by elliptic arcs. The influence of sweepback and contour upon the neutral point is shown.

Lange↗
NASA NTRS1990

Navier-Stokes computations on swept-tapered wings, including flexibility

A procedure to couple the Navier-Stokes solutions with modal structural equations of motion is presented for computing aeroelastic responses of flexible fighter wings. The Navier-Stokes flow equations are solved by a finite-difference scheme with dynamic grids. The coupled aeroelastic equations of motion are solved using the linear-acceleration method. The configuration-adaptive dynamic grids are time-accurately generated using the aeroelastically deformed shape of the wing. The coupled calculations are compared with experiments when available. Effects of flexibility and pitch rate are demonstrated for flows with vortices. Turbulent flow computations are also compared with laminar flow computations.

Guruswamy, Guru P.↗