Search NASA⌕ Search

SEARCH · Search NASA

Results for “Welding Distortion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Helium pressure increase inside GPHS clads: implications for formation of distended clads

Distension of GPHS clads has generally been attributed to gas buildup inside the clad. The bulging vent frit cover can be caused only by gas pressure, since the vent cover is isolated from the fuel by the vent frit. Gas generation is the only change expected as the oxide fuel ages. However, several data suggest that gas pressure is not the origin of the distension of the clad body. Gas pressure sufficient to distend the iridium body of the clad would be on the order of 1500 psi. This high pressure is very unlikely to be reached inside a GPHS clad, because the vent frit cover weld cannot sustain high pressures. Every distended clad that has been examined has an open vent frit, suggesting that the vent frit cover eventually opens on all distended GPHS clads. No gas pressure has been observed in any distended clad. In addition, the vent frit cover is sufficiently thin, about 2 grains thick, that diffusion of helium through the intact cover is possible and almost certainly occurs. Conversely, no clad has ever been definitively observed to distend after venting. Removal of the vent cover allows free escape of any radiolytically generated helium. However, there is little data on the behavior of vented GPHS. The vent cover is seldom removed at LANL, and vent covers are not removed on clads that will be stored. The vent covers are known to have been removed from the four clads residing in a module which was stored for 8 years. Expansion of the fuel is more likely to provide sufficient force on the iridium clad to distort the iridium metal. Radiographs indicate that the fuel inside a distended GPHS clad is also distended, filling all or most of the interior volume of the GPHS. No radiograph shows the fuel expanded and in contact with the weld shield and the distorted side of the GPHS clad without distension. However, radiography is infrequently done on stored clads unless they exhibit distension, so the dimensions of fuel in normal clads are not generally known.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Power Density Distributions in Electron Beams

Measuring and controlling the power density distribution of electron beams used for welding is critical for producing repeatable welds and for transferring welding parameters between different machines. On any given machine, the power density distribution is controlled by defocusing the beam relative to its sharpest focused condition. However, measuring the power density distribution can be difficult due to the intense nature of welding beams and is further complicated by imperfect electron optics that can distort the beam, making it difficult to quantify. The enhanced modified Faraday cup (EMFC) diagnostic method was used here for beam analysis that utilizes computed tomography to reconstruct the beam’s power density distribution. These results were compared to the International Standards Organization (ISO) method for characterizing laser beams using a second-moment D4σ calculation. For ideal Gaussian-shaped beams, both methods would give the same result. However, for imperfect beams, the calculated D4σ diameter was shown to be about 25% larger relative to the FWe2 diameter measured by the EMFC due to the heavier weighting of data in the tails of the beam by D4σ. Finally, although both methods produce repeatable welds, it is important to understand the differences in the reported beam diameters, divergence angles, and beam parameter products when transferring parameters between machines.

36 MATERIALS SCIENCE↗

Role of Computational Parameters on Predicting Self-Consistent Residual Stress and Distortion during Wire Arc Additive Manufacturing

Production of three-dimensional metallic parts through integration of an articulated robot and gas metal arc welding, also known as wire arc additive manufacturing (WAAM), can produce large-scale components with moderate geometrical complexity. This technology is particularly appealing due to its high deposition rates, scalability, and cost-effective feedstock compared to other AM processes. Despite its advantages, WAAM adoption is hindered by challenges in ensuring geometric conformity without extensive distortion, defect-free structures, and consistent mechanical properties. Finite element analysis (FEA) is often used to address the challenge of geometrical conformity. As the size of parts increases, the best practices for mesh size and temporal resolution known in the literature become computationally unviable. This research examined the effects of mesh and time-step resolutions during transient FEA of a large-scale (248 layers) metallic part. The impact of computational parameters on the thermal history, displacement, and residual stress distributions were evaluated. The results showed that predicted distortion was consistent across resolutions, while time-step length significantly affected predicted thermal history, and mesh size influenced residual stress distributions. To investigate this relationship further, directionally biased meshes were considered and analyzed. The results indicated that increasing mesh resolution perpendicular to the welding path yielded stress predictions that aligned closely with higher-resolution models while offering substantial computational savings. In conclusion, the significances of this research are related to verification and validation of WAAM models for widespread industrial adoption and pragmatic guidelines for optimizing computation parameters for balancing computational efficiency and predictive accuracy of residual stress and distortion.

Solsbee, Brandon [Univ. of Tennessee, Knoxville, T↗

Advanced Lightweight Metallic Fuselage Project Manufacturing Trade Study

Recent advances in large-scale flow forming of integrally stiffened cylinders (ISCs) have motivated evaluation of available technologies for rapid manufacturing of metallic fuselages. The current state-of-the-art in flow forming of ISCs produces 10-ft. diameter, 5-ft. long barrels with integral longitudinal blade stiffeners, and these single-piece ISCs are produced in approximately 1.5 hours. While other manufacturing processes are required to incorporate additional structural elements (ASE) such as circumferential ring frames, reinforcements around window and door cut-outs, and floors to the ISCs to complete the fuselage structure, flow forming technology may assist the aerospace industry in meeting manufacturing rate demands. In order to evaluate this technology, a fuselage manufacturing demonstration article (MDA) fabricated from two ISCs is scheduled for fabrication and delivery to NASA Langley Research Center (LaRC) by the end of 2022. In this study, eight manufacturing technologies were assessed to downselect candidate manufacturing processes for adding ASE to complete the MDA. A literature review and evaluation of contractor-produced panels covering a spectrum of welding and additive manufacturing (AM) processes were conducted at NASA LaRC. The analytical hierarchy process (AHP) was used to evaluate figures of merit (FOMs) for selecting manufacturing process(es) to integrate ASE with the ISCs to form a fuselage MDA. The AHP results revealed that scalability, structural performance, and distortion control were the most valued criteria for downselecting the manufacturing process to construct the internal stiffening structures. Based on the FOMs, this study concluded that a welding process is best suited for integrating the majority of the ASE, namely the circumferential ring frames. All of the welding processes received higher scores than AM processes due to higher maturity, higher structural performance, fewer post-processing requirements in machining and heat treating, and faster deposition rates. Among the welding processes, cold metal transfer (CMT) welding was ranked the most favorable process for assembling the MDA, with the other welding processes (laser welding (LW), friction stir welding (FSW), and refill friction stir spot welding (RFSSW)) scoring slightly lower. This was a consequence of the perceived maturity of the CMT welding process and its relatively high structural performance and low distortion resulting from the low heat input. Among the AM processes, CMT AM showed the greatest promise due to benefits derived from its scalability, lower 1st order process complexity, and low distortion. The AM processes may have potential for select applications, such as adding structural reinforcements around window and door cut-outs, but are not considered optimal for integrating the entire MDA.

Manufacturing↗

Experimental studies of a high-gradient X-band welded hard-copper split accelerating structure

We report on recent research on high-gradient radio frequency (RF) accelerating structures indicates that the use of hard copper alloys provides improvement in high gradient performance over annealed copper. Such structures are made by bonding individually manufactured parts. However, there are no well-established bonding techniques that preserve the hardness, surface finish and cleanliness required for high gradient operation. To preserve the copper hardness, RadiaBeam has developed a novel high-gradient split accelerating structure, based on electron beam welding joining technique. This technique provides efficient bonding with strong, clean welds and minimal thermal loading, while maintaining a clean inner RF environment. Our RF design and fabrication methodology limits the small heat affected zone to the outer cavity envelop, with virtually no distortions or thermal loading of critical RF surfaces. It also incorporates provisions to precisely control the gap despite conventional issues with weld joint shrinkage. To date we have manufactured and validated an RF accelerating structure joined by electron-beam welding that incorporates a novel open split design to significantly reduce the assembly complexity and cost. In this paper, we will present the electromagnetic design of this structure, discuss bonding, and present the results of high-power tests, where the accelerating gradients of 140 MV m -1 with surface peak fields of 400 MV m -1 were achieved for flat-top pulse length of 600 ns with an RF breakdown rate of 10 -4 1/(pulsecm).

43 PARTICLE ACCELERATORS↗

In-situ digital image correlation and thermal monitoring in directed energy deposition additive manufacturing

As in welding, directed energy deposition (DED) additive manufacturing (AM) generates complex residual stresses and distortions commensurate with the complexity of the scan pattern used for deposition. To date, measuring DED distortions on complex geometries has only been achieved post process, discarding the complex thermomechanical history that leads to that final material state. In this work, surround stereo digital image correlation (DIC) is used to 3D map surfaces and strain tensors in-situ in a powder-blown laser DED system. Infrared thermography is then projected onto these surfaces to record the full thermomechanical history of printed parts. DIC presents a unique challenge to DED AM, as no part exists at the beginning of deposition, which (a) prevents application of an appropriate speckle pattern and (b) denies the user a zero strain reference frame. Solutions to these problems are proposed and their limitations explored herein. In sum, this work presents a relatively low-cost solution to monitoring and optimizing the unique temporal artifacts induced by complex scan strategies that was previously unobtainable.

42 ENGINEERING↗

U-Groove Aluminum Weld Strength Improvement

Though butt-welds are among the most preferred joining methods in aerostructures, their strength dependence on inelastic mechanics is generally the least understood. This study investigated experimental strain distributions across a thick aluminum U-grooved weld and identified two weld process considerations for improving the multipass weld strength. One is the source of peaking in which the extreme thermal expansion and contraction gradient of the fusion heat input across the groove tab thickness produces severe angular distortion that induces bending under uniaxial loading. The other is the filler strain hardening decreasing with increasing filler pass sequences, producing the weakest welds on the last weld pass side. Both phenomena are governed by weld pass sequences. Many industrial welding schedules unknowingly compound these effects, which reduce the weld strength. A depeaking index model was developed to select filler pass thickness, pass numbers, and sequences to improve depeaking in the welding process. The result was to select the number and sequence of weld passes to reverse the peaking angle such as to combine the strongest weld pass side with the peaking induced bending tension component side to provide a more uniform stress and stronger weld under axial tensile loading.

Verderaime, V.↗

Operational Parameter Database for Molten Salt Thermal Energy Storage Tank Modeling

The second generation of concentrated solar power (CSP) plants is characterized by the use of a central receiver (either cavity or external), two molten nitrate salt tanks (60 wt.% NaNO 3 and 40 wt.% KNO 3 ), and a steam Rankine power-generation cycle connected through a primary heat exchanger. Molten salt thermal energy storage (TES) tanks have been widely deployed in commercial CSP plants worldwide and have been essential for increasing plant dispatchability and capacity factor, while also reducing the levelized cost of electricity (LCOE). These systems enable energy storage at the gigawatt-hour scale, typically providing 6 to 17 hours of storage duration. Despite being a commercial technology, the multiple failures observed after only a few months or years of operation in plants around the world demonstrate the technology's relative infancy and highlight the need for further research to improve its reliability. The National Laboratory of the Rockies (NLR), in collaboration with industry partners and academic and research institutions, has been leading multiple projects funded by the U.S. Department of Energy (DOE). These projects focus on addressing molten salt tank failures by improving tank design and welding fabrication practices, evaluating new alloys and weld fillers, and providing guidelines for tank commissioning and safe operation. In particular, this report presents modeling results on the effect of key tank operation parameters during 60 minutes of operation, including the mass flow rate and temperature of the salt inflow, tank salt inventory temperature, and inventory level for a representative molten salt tank design. These results form a database of tank operation behaviors that captures the effects of each specific parameter during charging, charging/discharging, and discharging processes.

14 SOLAR ENERGY↗

Mitigation of distortion of Al/steel part under simulated paint baking condition: Experiment and numerical model studies

Multi-material joining of lightweight structures is essential to reduce vehicle weight for more energy savings and less greenhouse gas emission. However, mismatch of thermal expansion coefficient for dissimilar materials during the paint baking process can induce part distortion and joint failure for adhesive bonding. Here, in the present work, a thermomechanical model based on contact mechanics and large deformation theory was developed for dissimilar high-strength Al alloy and steel components to study the distortion mechanism and influential factors of the residual gap. The established model was used to optimize joint conditions, such as pitch distance and part geometry. When a weld pitch is shorter than 100 mm, the maximum gap between Al and steel part can be greatly reduced to 0.1 mm, and the local stress and plastic strain around the joint during the oven heating and cooling cycle are also substantially reduced compared with the long pitch case (900 mm). The numerical modeling results revealed that a comparable bending stiffness ratio between the steel and Al cross sections is critical to the minimization of gap and distortion under paint baking condition. Digital image correlation technique was used to measure the overall part distortion and local strain distribution that were used to validate the model prediction. Weld bonding (adhesive bonding with friction bit joining) process was successfully employed to join Al to steel component without gap opening in adhesive after the paint baking and cooling.

36 MATERIALS SCIENCE↗

Improvement of Al/Steel Tungsten Inert Gas Welding–Brazing Joint by High-Energy Shot Peening

High-energy shot peening treatment was applied to improve the Al/steel tungsten inert gas welding–brazing lap joint. The mechanical properties and microstructure evolution of the joint were investigated. Results showed that the mechanical properties of weld were evidently reinforced due to microstructure transformation of joint surface layer. The grain structure in the joint surface layer was distorted and refined. Large compressive residual stress was introduced into the joint surface, and its hardness obviously increased due to strain hardening. When the peening pressure was 0.15 MPa, the tensile shear strength of the joint reached the maximum value (199.6 MPa), which was 16.5% higher than that of the as-welded joint.

36 MATERIALS SCIENCE↗

Metal Big Area Additive Manufacturing: Process Modeling and Validation

Metal Big Area Additive Manufacturing (mBAAM) is a new additive manufacturing (AM) technology for printing large-scale 3D objects. mBAAM is based on the gas metal arc welding process and uses a continuous feed of welding wire to manufacture an object. An electric arc forms between the wire and the substrate, which melts the wire and deposits a bead of molten metal along the predetermined path. In general, the welding process parameters and local conditions determine the shape of the deposited bead. The sequence of the bead deposition and the corresponding thermal history of the manufactured object determine the long range effects, such as thermal-induced distortions and residual stresses. Therefore, the resulting performance or final properties of the manufactured object are dependent on its geometry and the deposition path, in addition to depending on the basic welding process parameters. Physical testing is critical for gaining the necessary knowledge for quality prints, but traversing the process parameter space in order to develop an optimized build strategy for each new design is impractical by pure experimental means. Computational modeling and optimization may accelerate development of a build process strategy and saves time and resources. Because computational modeling provides these opportunities, we have developed a physics-based Finite Element Method (FEM) simulation framework and numerical models to support the mBAAM process s development and design. In this paper, we performed a sequentially coupled heat transfer and stress analysis for predicting the final deformation of a small rectangular structure printed using the mild steel welding wire. Using the new simulation technologies, material was progressively added into the FEM simulation as the arc weld traversed the build path. In the sequentially coupled heat transfer and stress analysis, the heat transfer was performed to calculate the temperature evolution, which was used in a stress analysis to evaluate the residual stresses and distortions. In this formulation, we assume that physics is directionally coupled, i.e. the effect of stress of the component on the temperatures is negligible. The experiment instrumentation (measurement types, sensor types, sensor locations, sensor placements, measurement intervals) and the measurements are presented. The temperatures and distortions from the simulations show good correlation with experimental measurements. Ongoing modeling work is also briefly discussed.

Additive Manufacturing↗

Consumable development to tailor residual stress in parts fabricated using directed energy deposition processes

Distortion and residual stresses are major challenges that limit the ability to fabricate large scale structures using Additive Manufacturing (AM). Researchers worldwide are evaluating techniques to induce compressive residual stress in the parts via intermittent rolling. While reasonable success has been documented, the idea of lowering the martensite start temperature to induce compressive stresses has not been evaluated in the context of AM, despite demonstrated success by the welding community. This study validates the hypothesis that, by a proper selection of materials and process parameters, one may effectively reduce distortion and induce a compressive residual stress in AM parts. Using neutron diffraction to measure residual stresses in parts, we demonstrate that, in addition to selection of the correct materials, the inter pass temperature plays a major role in controlling the residual stress evolution. The observations relating to the residual stresses are rationalized based on a microstructural evolution in these samples. Based on this preliminary study, a strategy to fabricate large structures with minimal distortion and residual stress is outlined.

36 MATERIALS SCIENCE↗

Influence of Tool Runout on Force Measurement During Internal Void Monitoring for Friction Stir Welding of 6061-T6 Aluminum

Abstract The goal of this research was to examine how altering the amount of friction stir tool eccentricity while controlling the amount of slant in the tool shoulder (drivers of oscillatory process forces) effects the generation of process force transients during sub-surface void interaction. The knowledge gained will help improve the accuracy of force-based void monitoring methods that have the potential to reduce the need for post-weld inspection. Process force transients during sub-surface void formation were examined for multiple tools with varying magnitudes of kinematic runout. The eccentric motion of the tool produced oscillations in the process forces at the tools rotational frequency that became distorted when features (flats) on the tool probe interacted with voided volumes, generating an amplitude in the force signals at three times the tool rotational frequency (for three-flat tools). A larger tool eccentricity generates a larger amplitude in the force signals at the tool’s rotational frequency that holds a larger potential to create a distortion during void interaction. It was determined that once void becomes large enough to produce an interaction that generates an amplitude at the third harmonic larger than 30% of the amplitude at the rotational frequency in a weld with no interaction (amplitude solely at rotational frequency), the trailing edge of the tool shoulder cannot fully consolidate the void, i.e., it will remain in the final weld. Additionally, once the void exceeds a certain size, the amplitudes of the third harmonics saturate at 70% of the amplitude at the rotational frequency during full consolidation. The interaction between the eccentric probe and sub-surface void was isolated by ensuring any geometric imperfection in the shoulder (slant) with respect to the rotational axis was removed. The results suggest that geometric imperfections (eccentricity and slant) with respect to the tool’s rotational axis must be known when developing a void monitoring method from force transients of this nature.

Engineering↗

Coherence Weighting Applied to FMC/TFM Data from Austenitic CRA Clad Lined Pipes

Lined pipe girth weld regions are challenging to inspect using ultrasonic techniques due to their anisotropic and inhomogeneous characteristics, which lead to noise and acoustic beam distortion. This paper is focused on the application of coherence weighting methods to decrease the background noise level and false indications on total focusing method (TFM) images, encompassing the triple boundary of mechanically lined pipes. Three coherence weighting approaches were used here; the coherence factor (CF), the sign CF (SCF) and the phase CF (PCF). All three were found capable to improve the TFM images, however, the CF and the SCF performed better due to their exponential sensitivity factors, unlike the PCF which has a linear sensitivity factor.

42 ENGINEERING↗

NDE of Friction Stir Welds in Aerospace Applications

Friction Stir Welding (FSW) is a solid state joining process, which utilizes a cylindrical, shouldered pin tool with a radiused tip that is rotated and plunged into the weld joint. Frictional heating beneath the shoulder, and surrounding the pin tip causes the material to plasticize, intermix and consolidate into a weldment without melting the parent material. FSW in aluminum alloys has many advantages such as low distortion and shrinkage, excellent mechanical properties, and no porosity. However, the propensity of the FSW process to create detrimental defects does exist, and is dependent on FSW parameter limits and controls. Inspection processes for FSW must also be selected and implemented concurrent with the new weld process. This paper describes the efforts by Lockheed Martin and NASA to find proper NDE techniques for detecting and characterizing the anomalies that may be caused by operating outside the envelope of optimized FSW parameters. Potential defects are identified and the results of the exploration of numerous NDE techniques including visual, liquid penetrant, multiple ultrasonic methods, eddy current and conductivity are discussed.

Kinchen, David G.↗

Defect Detection of Industrial Radiography Images of Ammonia Pipes by a Sparse Coding Model

Pipeline transportation systems for liquid anhydrous ammonia require periodic inspections for pipe defects. Defects such as crack-like flaws, including those due to stress corrosion and fatigue crack growth and fatigue of welded joints, can be tested by in situ radiography testing (RT). It is required that the detection technique should reveal the defect region without any significant distortion. Imaging noise such as that due to radiation scattering reduces contrast over the whole or part of the image, causing a reduction in image quality. Various image processing methods can be utilized to improve the outcome of RT of pipes. The sparse coding model is a powerful contrast improvement algorithm, but it tends to eliminate imaging details, passing them off as noise. We present a novel implementation of the sparse coding model based on a probabilistic interpretation to improve defect detection in ammonia pipelines radiography images. The performance of this procedure was evaluated in radiographic images of defect and corrosion regions for different pipe types. For ammonia pipes, the technique was found to offer a significant improvement in defect detection while preserving imaging details.

42 ENGINEERING↗

The Effect of Laser Scan Strategy on Distortion and Residual Stresses of Arches Made With Selective Laser Melting

The NASA Marshall Space Flight Center (MSFC) is developing Additive Manufacturing (AM) - both in-space AM for on-demand parts, tools, or structures, and on-earth AM for rapid, reduced-cost, small volume production of complex space-flight hardware. Selective Laser Melting (SLM) is an on-earth AM technology that MSFC is using to build Alloy 718 rocket engine components. An understanding of the SLM-718 material properties is required to design, build, and qualify these components for space flight. Residual stresses and are of particular interest for this AM process, since SLM is a series of approximately 100 micron-wide welds, where highly non-linear heating and cooling, severe thermal gradients and repeated thermal cycling can result in high residual stresses within the component. These stresses may cause degraded material properties, and warp or distort the geometry of the SLM component. The distortions can render the component out-of-tolerance when inspected, and even interrupt or halt the build process if the warped material prevents the SLM machine from operating properly. The component must be scrapped and re-designed, which is time consuming and costly. If residual stresses are better understood, and can be predicted, these effects can be mitigated early in the component's design. the compressive residual stresses in the z-direction were highest in the chess sample, followed by island then continuous. This may be due to the binding nature of the segments

Bagg, Stacey D.↗

Evaluating the Electrochemical Behavior of Friction Stir-Welded AA2219-O Alloy Joint in 3.5% NaCl Solution

Single-pass friction stir welding of AA2219-O aluminum alloy was carried out at high rotation speed (1180 rpm), and transverse travel rate of 33.5 mm/min was selected. The microstructural, mechanical and electrochemical characteristics of the weldment are investigated in this study. The high rotational tool speed resulted in a less uniform distribution of the intermetallic θ-phase (CuAl{sub 2}) in the thermo-mechanically affected zone (TMAZ) than in the weld nugget zone (WNZ). The higher transfer coefficient and lower charge transfer resistance (R{sub ct} + R{sub θ}) were observed in case of TMAZ as evaluated from potentiodynamic polarization and impedance spectroscopy, respectively. These results confirmed that microstructural variations could deteriorate the electrochemical performance of the weldment. TMAZ provided the least corrosion resistance than the base metal (BM) and WNZ due to the high concentration of cathodic intermetallic particles and possibly due to the large mechanical distortion of the grain structure.

36 MATERIALS SCIENCE↗