Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wood”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Wood‐density has no effect on stomatal control of leaf‐level water use efficiency in an Amazonian forest

Forest disturbances increase the proportion of fast-growing tree species compared to slow-growing ones. To understand their relative capacity for carbon uptake and their vulnerability to climate change, and to represent those differences in Earth system models, it is necessary to characterise the physiological differences in their leaf-level control of water use efficiency and carbon assimilation. We used wood density as a proxy for the fast-slow growth spectrum and tested the assumption that trees with a low wood density (LWD) have a lower water-use efficiency than trees with a high wood density (HWD). We selected 5 LWD tree species and 5 HWD tree species growing in the same location in an Amazonian tropical forest and measured in situ steady-state gas exchange on top-of-canopy leaves with parallel sampling and measurement of leaf mass area and leaf nitrogen content. We found that LWD species invested more nitrogen in photosynthetic capacity than HWD species, had higher photosynthetic rates and higher stomatal conductance. Furthermore, contrary to expectations, we showed that the stomatal control of the balance between transpiration and carbon assimilation was similar in LWD and HWD species and that they had the same dark respiration rates.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

AmeriFlux FLUXNET-1F US-EA6 Camp Wood Shield Ranch Oak Savannah

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site US-EA6 Camp Wood Shield Ranch Oak Savannah. This is the FLUXNET version of the carbon flux data for the site US-EA6 Camp Wood Shield Ranch Oak Savannah produced by applying the standard ONEFlux (1F) software. Site Description - This tower is located on the Shield Ranch, approximately 5 km southeast of Camp Wood, TX. The tower consists of a permanent structure located on a flat creek terrace between stands of oak trees.

Fleck, Preston [The University of Texas at Austin,↗
DOE OSTI2022

Wood combustion nanoparticles emitted by conventional and advanced technology cordwood boilers, and their interactions in vitro with human lung epithelial monolayers

Biomass-burning boilers and stoves are widely used in many parts of the world, producing combustion emissions linked with health risks. Here, combustion emission nanoparticles (NPs) were collected from four representative wood burning boilers using oak cordwood at specific times in the burn cycle. The morphology and composition of the NPs was characterized using transmission electron microscopy and energy dispersive X-ray analysis. To determine the degree of NP cytotoxicity with human lung tissue, the combustion NPs were introduced to incubated lung bronchial epithelial monolayers (NCI-H292) in vitro at doses of 0.1×10 -6 and 3.0×10 -6 kg/L for 2 and 4 h. Histochemical analysis showed that cell death increased by a factor of 3.5 for both doses after 4 h when compared to the control. Ultrapure NPs prepared by wet chemical methods were also introduced to the epithelial lung cells for similar doses and exposure times and the cultures exhibited significantly reduced mortality. Electron microscopy was used to study the mechanism of cell mortality for the synthesized and combustion-based NPs by examining how the NP byproducts interacted with individual cell organelles. It was found that cell survival was strongly correlated with the absence of contaminants (salts, heavy metals, poly aromatic hydrocarbons) associated with the NPs entering the cells. Synthesized NPs consisting of pure carbon were relatively well tolerated and could be excreted without damaging the cell ultrastructure. Thus, careful removal of extraneous contaminants by controlling the burn cycle with a catalyst is essential to minimize the health and environmental effects of wood biofuel combustion. In better words, optimized advanced technology wood-burning boilers and stoves can provide a CO 2 -neutral energy source and significantly contribute to a future where fossil fuels have a reduced role.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Evaluation of a Smoke Opacity Sensor for Improving Residential Wood Heater Combustion

Residential wood heating lacks real-time particulate matter (PM) monitoring technologies capable of measuring emissions directly from flue gases. This study evaluates the performance of the Octoring, an opacity-based smoke sensor developed to monitor wood heater emissions and provide feedback for improved combustion. The device was tested on catalytic and non-catalytic cordwood heaters and a pellet heater during startup, high-burn, and low-burn phases. Performance was assessed against reference particle instruments and gravimetric measurements using concordance, correlation, and agreement analyses. Results show that temperature-dependent drift is the primary limitation affecting sensor accuracy, with systematic drift observed across ambient and combustion conditions. Agreement with reference instruments ranged from poor to good depending on operating conditions, with the strongest performance observed during pellet heater high-burn operation. These findings establish a performance baseline for opacity-based sensing technologies and identify key areas for further development before practical deployment in residential wood combustion monitoring systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Results of the 2018 Wood Stove Design Challenge

The 2018 Wood Stove Design Challenge was an international design competition which sought to identify top performing residential wood stoves based on automation. To prepare for the event, the Northeast States for Coordinated Air Use Management (NESCAUM) developed a testing protocol that challenged the stoves by testing them in more field-like conditions—capturing emissions from start-up, reloading a stove, and the use of larger piece sizes. Flue gas emissions were measured using a combination of in-stack and novel dilution sampling methods, as the event occurred on the National Mall in Washington D.C. in a non-laboratory setting. Particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO2), and methane (CH4) were measured from three stoves in real-time. A combustion efficiency was also calculated for each stove in real-time. Measured PM emission rates ranged between 1.8 and 8.0 g/hr for all stoves and operating conditions, with the highest emissions being measured during cold start in all cases. The test average PM emission rates were 2.4, 4.0, and 2.4 g/hr for stoves A, B, and C, respectively. Results showed emissions measured during transient operations, which are often excluded in current certification methods, can be significantly higher than steady-state periods—echoing other studies and highlighting the importance of testing in various operational modes for more realistic emission estimates. Additionally, the stoves had overall CO emission rates of 48.8, 284.8, and 100.8 g/hr, for stoves A, B and C, respectively. Calculated PM and CO emission factors overall were low considering the testing protocol sought to follow more challenging yet realistic practices in terms of fuel loading and operating procedures. The overall estimated combustion efficiency for stoves A, B, and C was 85%, 78%, 76%, respectively and in all cases was lowest during the cold start period.This report details the successfully proposed and assembled instrumentation that was relatively portable for field-site testing and the results of the emissions measurements for the 2018 Wood Stove Design Challenge competition. Overall, the repeatability of each stove was favorable with coefficients of variation (COV) ranging from 7 to 15% for measured PM concentrations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Roles for epigenetics in wood formation and stress response intrees–from basic biology to forest management

Annual model and crop species have been the subject of most epigenetic studies for plants. In contrast to annuals, forest trees persist on natural landscapes and experience environmental variation within and across seasons, years, and decades or even centuries. Most forest trees species are undomesticated and typically grown on variable landscapes with no irrigation or application of agricultural chemicals. Forest trees must thus rely on their inherent ability to alter growth and physiology to mitigate the effects of changing abiotic and biotic stressors. Like other plants, trees have mechanisms encoded in their genomic DNA sequence that can respond directly to stress events such as drought or heat. Hypothetically, it would be highly advantageous to join these mechanisms with a dynamic “memory” of past exposure to stress. It is now well established that annual model and crop plants can establish epigenetic-based memory of stress events that support more rapid and robust response to stress in the future. Here, evidence is discussed for epigenetic regulation and “memory” in two fundamental biological processes in trees, wood formation and abiotic stress response. Wood formation is an ideal trait for epigenetic research in trees, as wood formation is highly responsive to environmental conditions and includes multiple rapid developmental changes as cells adopt distinct fates within complex tissues. This is followed by a discussion of research needs that would provide the foundation for new epigenetic applications for forestry.

Groover, Andrew↗
DOE OSTI2020

Aboveground Wood Production Is Sustained in the First Growing Season after Phloem-Disrupting Disturbance

Carbon (C) cycling processes are particularly dynamic following disturbance, with initial responses often indicative of longer-term change. In northern Michigan, USA, we initiated the Forest Resilience Threshold Experiment (FoRTE) to identify the processes that sustain or lead to the decline of C cycling rates across multiple levels (0, 45, 65 and 85% targeted gross leaf area index loss) of disturbance severity and, in response, to separate disturbance types preferentially targeting large or small diameter trees. Simulating the effects of boring insects, we stem girdled > 3600 trees below diameter at breast height (DBH), immediately and permanently disrupting the phloem. Weekly DBH measurements of girdled and otherwise healthy trees (n > 700) revealed small but significant increases in daily aboveground wood net primary production (ANPP w ) in the 65 and 85% disturbance severity treatments that emerged six weeks after girdling. However, we observed minimal change in end-of-season leaf area index and no significant differences in annual ANPP w among disturbance severities or between disturbance types, suggesting continued C fixation by girdled trees sustained stand-scale wood production in the first growing season after disturbance. We hypothesized higher disturbance severities would favor the growth of early successional species but observed no significant difference between early and middle to late successional species’ contributions to ANPP w across the disturbance severity gradient. We conclude that ANPP w stability immediately following phloem disruption is dependent on the continued, but inevitably temporary, growth of phloem-disrupted trees. Our findings provide insight into the tree-to-ecosystem mechanisms supporting stand-scale wood production stability in the first growing season following a phloem-disrupting disturbance.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

IM3 Phase 2 Official Simulations: GCAM-Demeter-SELECT Annualized Land Use and Land Cover, Wood Harvest and Fertilization Data with Dynamic Urbanization Harmonized to CLM Land Definitions at 0.125 Degrees

Annualized land use land cover data, including wood harvest and fertilizer use data from the Global Change Analysis Model (GCAM) downscaled to 0.125 degrees for couping with the Community Land Model (CLM). GCAM here refers to GCAM-USA v5.3.im3 which has an enhanced electricity sector and an updated data system needed to represent regional to local scale dynamics. Data is also harmonized with future urbanization projections from the Spatially-Explicit, Long-term, Empirical City developmenT (SELECT) model. Projections/Data are generated using the demeter land use and land cover downscaling model. Original projections were generated at 0.05 degrees before being aggregared to 0.125 degrees. Projections are available for 8 alternative scenarios. Two versions of final data are included- one with managed forests or harvested forest area per pixel broken out and one with the same aggregated into total forests. Following folders are included: demeter_78_PFT_output:This is the final output of dynamic land use land cover change for 78 PFTs as required by CLM raw_outputs_incl_managed_forest: This is the final output but with managed forests broken out as a different PFT. Essentially a 79th PFT is added. wood_harvest_outputs: Wood harvest output per pixel in gC/m2 fertilization_outputs: Fertilizer use per pixel in gN/m2 Each NetCDF file in each folder represents a projection for a separate year, scenario. Land use outputs are organized as PFT level data saved as subdata. Link to GCAM version used- https://data.msdlive.org/records/yb23g-44274 Link to SELECT documentation -https://www.sciencedirect.com/science/article/pii/S1364815219301707 Link to CLM documentation- - https://www.cesm.ucar.edu/models/clm In case of questions contact- kanishka.narayan@pnnl.gov

GCAM-USA↗
DOE OSTI2025

Optimization of Delignified Wood Rods for Interfacial Solar Evaporation

Interfacial solar evaporation using three-dimensional evaporator materials has shown promise to achieve high evaporation rates exceeding the photothermal limit for water treatment and resource recovery processes. However, challenges remain in optimizing the material geometry to balance the vertical capillary uptake of water and the rate of evaporation to achieve both stable and high evaporation rates. Delignified wood can serve as a highly porous and hydrophilic substrate material to achieve high evaporation rates. In this work, we designed a suspended biochar-coated delignified wood rod evaporator and investigated the influence of its geometric parameters on its evaporation performance. The height of the evaporator exposed to air for evaporation was observed to be an important parameter in governing the evaporation rate, as shorter evaporators limited the available surface area for evaporation, but taller evaporators could not achieve sufficient rates of capillary uptake to maintain stable evaporation rates over 24 h under 1-sun illumination (1 kW m –2 ). In conclusion, the exposed height of the evaporator was optimized to achieve an average hourly evaporation rate of 3.05 ± 0.23 kg m –2 h –1 , which could be maintained in saline solutions containing up to 5 wt % NaCl.

Coating materials↗
DOE OSTI2021

Wood Carbon Based Single-Atom Catalyst for Rechargeable Zn–Air Batteries

Low-cost and efficient oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) bifunctional electrocatalysts are vital for the applications of rechargeable Zn-air batteries (ZABs). Given the high catalytic activity of single-atom catalysts (SACs), preparing SACs on a large scale for ZABs is desirable but remains challenging. Herein, in situ formation of single-atom Fe-N-C catalysts on plate wood-based porous carbon is achieved via a facile Lewis acid pretreatment and carbonization process. Lewis acid FeCl3 pretreatment on the cell wall of wood not only produces abundant microchannels but also successfully introduces atomically dispersed Fe-N active species into the hierarchical structure. Such uniformly dispersive SACs on the hierarchical structure enhance the ORR/OER performance and durability. A ZAB using the catalyst in the cathode shows a high power density (70.2 mW cm -2 , at quasi solid state) and long-term stability. This work provides a new path for the large-scale preparation of high-performance SACs.

25 ENERGY STORAGE↗
DOE OSTI2025

Vanderwaltozyma urihicola sp. nov., a yeast species isolated from rotting wood and beetles in a Brazilian Amazonian rainforest biome

Five yeast isolates belonging to a candidate for novel species were obtained from rotting wood and the gut of a passalid beetle larva in a site of Amazonian rainforest biome in Brazil. Sequence analysis of the Internal Transcribed Spacer (ITS)-5.8S region and the D1/D2 domains of the large subunit rRNA gene showed that the isolates represent a novel species of the genus Vanderwaltozyma. The closest relative of the novel species is Vanderwaltozyma huisunica. These species differs due to 44 nt substitutions and 21 indels in the sequences of the ITS region, as well as by 15 substitutions and four indels in the sequences of the D1/D2 domains. A phylogenomic analysis of the Vanderwaltozyma species with genomes sequenced showed that this novel species is an outgroup to the other species of this genus. We propose the name Vanderwaltozyma urihicola sp. nov. (CBS 18107T, MycoBank MB 856975) to accommodate these isolates. Furthermore, the species is homothallic, producing one to two ascospores per ascus. The habitat of V. urihicola is rotting wood in the Brazilian Amazonian rainforest biome.

Amazonian Forest↗
DOE OSTI2025

Nanoporous Wood Chips Based Sizable, Robust, and Low-Cost Honeycomb Vacuum Insulation Panels (DOE BENEFIT Final Research Performance Progress Report (RPPR))

Conventional vacuum insulation panels (VIPs) suffer from severe limitations including high cost, vulnerability to perforation, and significant performance degradation over time due to vacuum loss. InventWood Inc. (IW) and partnering teams completely re-engineered the VIP structure by constructing arrays of isolated vacuum-cells to enable limited cutting at designated areas (in between vacuum cells) and reduced consequential vacuum loss due to puncture. The teams also replaced the expensive vacuum insulation core materials with a low-cost commercial wood pulp and recycled long fiber. The wood pulp derived VIP can deliver an overall panel insulation of R15 (<0.01W/m·K) with over 90% thermal resistance retention after cutting (R13.5 overall, R5 along the cut edges). In addition, the vacuum-cell-array design minimizes edge losses, resulting in more durable performance, longer service life (>50 years), and higher R-value per dollar towards a cost target of <$1/ft 2 ·in. It is anticipated that the Nanochip-VIP will attract strong market interest and become an affordable insulation solution for energy efficient buildings and retrofits, leading to significant reductions in energy usage.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Eucalyptus Wood Smoke Extract Elicits a Dose-Dependent Effect in Brain Endothelial Cells

The frequency, duration, and size of wildfires have been increasing, and the inhalation of wildfire smoke particles poses a significant risk to human health. Epidemiological studies have shown that wildfire smoke exposure is positively associated with cognitive and neurological dysfunctions. However, there is a significant gap in knowledge on how wildfire smoke exposure can affect the blood–brain barrier and cause molecular and cellular changes in the brain. Our study aims to determine the acute effect of smoldering eucalyptus wood smoke extract (WSE) on brain endothelial cells for potential neurotoxicity in vitro. Primary human brain microvascular endothelial cells (HBMEC) and immortalized human brain endothelial cell line (hCMEC/D3) were treated with different doses of WSE for 24 h. WSE treatment resulted in a dose-dependent increase in IL-8 in both HBMEC and hCMEC/D3. RNA-seq analyses showed a dose-dependent upregulation of genes involved in aryl hydrocarbon receptor (AhR) and nuclear factor erythroid 2-related factor 2 (NRF2) pathways and a decrease in tight junction markers in both HBMEC and hCMEC/D3. When comparing untreated controls, RNA-seq analyses showed that HBMEC have a higher expression of tight junction markers compared to hCMEC/D3. In summary, our study found that 24 h WSE treatment increases IL-8 production dose-dependently and decreases tight junction markers in both HBMEC and hCMEC/D3 that may be mediated through the AhR and NRF2 pathways, and HBMEC could be a better in vitro model for studying the effect of wood smoke extract or particles on brain endothelial cells.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Exploiting the Properties of Non-Wood Feedstocks to Produce Tailorable Lignin-Containing Cellulose Nanofibers

Lignin-containing cellulose nanofibrils (LCNFs) are mainly produced commercially from treated wood pulp, which can decrease some of the carbon-negative benefits of utilizing biomass feedstock. In this work, LCNFs are prepared from non-wood feedstocks, including agricultural residues such as hemp, wheat straw, and flax. These feedstocks allowed for the preparation of LCNFs with a variety of properties, including tailored hydrophobicity. The feedstocks and their subsequent LCNFs are extensively characterized to determine the roles that feedstocks play on the morphology and properties of their resultant LCNFs. The LCNFs were then incorporated into paper handsheets to study their usefulness in papermaking applications, which indicated good potential for the use of wheat straw LCNFs as a surface additive to improve the oil resistance coating.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Utilization of Synthetic Near-Infrared Spectra via Generative Adversarial Network to Improve Wood Stiffness Prediction

Near-infrared (NIR) spectroscopy is widely used as a nondestructive evaluation (NDE) tool for predicting wood properties. When deploying NIR models, one faces challenges in ensuring representative training data, which large datasets can mitigate but often at a significant cost. Machine learning and deep learning NIR models are at an even greater disadvantage because they typically require higher sample sizes for training. In this study, NIR spectra were collected to predict the modulus of elasticity (MOE) of southern pine lumber (training set = 573 samples, testing set = 145 samples). To account for the limited size of the training data, this study employed a generative adversarial network (GAN) to generate synthetic NIR spectra. The training dataset was fed into a GAN to generate 313, 573, and 1000 synthetic spectra. The original and enhanced datasets were used to train artificial neural networks (ANNs), convolutional neural networks (CNNs), and light gradient boosting machines (LGBMs) for MOE prediction. Overall, results showed that data augmentation using GAN improved the coefficient of determination (R 2 ) by up to 7.02% and reduced the error of predictions by up to 4.29%. ANNs and CNNs benefited more from synthetic spectra than LGBMs, which only yielded slight improvement. All models showed optimal performance when 313 synthetic spectra were added to the original training data; further additions did not improve model performance because the quality of the datapoints generated by GAN beyond a certain threshold is poor, and one of the main reasons for this can be the size of the initial training data fed into the GAN. LGBMs showed superior performances than ANNs and CNNs on both the original and enhanced training datasets, which highlights the significance of selecting an appropriate machine learning or deep learning model for NIR spectral-data analysis. The results highlighted the positive impact of GAN on the predictive performance of models utilizing NIR spectroscopy as an NDE technique and monitoring tool for wood mechanical-property evaluation. Further studies should investigate the impact of the initial size of training data, the optimal number of generated synthetic spectra, and machine learning or deep learning models that could benefit more from data augmentation using GANs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Powering the Woods Hole X-Spar Buoy with Ocean Wave Energy—A Control Co-Design Feasibility Study

Despite its success in measuring air–sea exchange, the Woods Hole Oceanographic Institution’s (WHOI) X-Spar Buoy faces operational limitations due to energy constraints, motivating the integration of an energy harvesting apparatus to improve its deployment duration and capabilities. This work explores the feasibility of an augmented, self-powered system in two parts. Part 1 presents the collaborative design between X-Spar developers and wave energy researchers translating user needs into specific functional requirements. Based on requirements like desired power levels, deployability, survivability, and minimal interference with environmental data collection, unsuitable concepts are pre-eliminated from further feasibility study consideration. In part 2, we focus on one of the promising concepts: an internal rigid body wave energy converter. We apply control co-design methods to consider commercial of the shelf hardware components in the dynamic models and investigate the concept’s power conversion capabilities using linear 2-port wave-to-wire models with concurrently optimized control algorithms that are distinct for every considered hardware configuration. During this feasibility study we utilize two different control algorithms, the numerically optimal (but acausal) benchmark and the optimized damping feedback. We assess the sensitivity of average power to variations in drive-train friction, a parameter with high uncertainty, and analyze stroke limitations to ensure operational constraints are met. Our results indicate that a well-designed power take-off (PTO) system could significantly extend the WEC-Spar’s mission by providing additional electrical power without compromising data quality.

autonomous systems↗
DOE OSTI2024

Material property characterization of 3D printed polypropylene wood plastic composites

Abstract Wood flour (WF) at 10 wt.% and 20 wt.% loadings was used as a reinforcing filler to enhance the applicability of polypropylene (PP) for 3D printing. After performing printability tests of PP wood plastic composites (WPCs), the mechanical properties of both injection‐molded and 3D‐printed PP WPC specimens were explored. Test specimens were prepared from 3D printed hexagons for analyzing the mechanical properties. Adding WF to neat PP increased the storage modulus and the glass transition temperature while decreasing the degree of crystallinity and the coefficient of thermal expansion, while enhancing the printability of neat PP. The tensile strength, tensile modulus of elasticity, flexural strength, and flexural modulus of elasticity of injection‐molded neat PP improved by up to 21%, 59%, 30%, and 56%, respectively, with 20 wt.% WF. However, the impact strength of injection‐molded neat PP decreased by 85%, with 20 wt.% WF. After 3D printing, the tensile strength and tensile modulus of elasticity of printed neat PP increased by up to 84% and 60%, respectively, with 20 wt.% WF. The flexural strength and flexural modulus of elasticity of neat printed PP remained unchanged compared to those of PP filled with 20 wt.% WF, while the impact strength decreased by 87%. Highlights WF was used as a reinforcement in polypropylene designed for 3D printing A pilot‐scale, pellet‐fed 3D printer was used to print hollow hexagons, and then test specimens were fabricated from these hexagons for mechanical properties The tensile and flexural properties of 3D printed neat polypropylene improved, while the impact strength decreased after adding 20 wt.% WF to the neat PP.

Hwang, Sungjun↗
DOE OSTI2022

Pectin-associated mannans and xylans play distinct roles in cell-cell adhesion in pine and poplar wood

Wood particles of pine required longer treatments of acidic chlorite and dilute alkali to achieve similar proportions of cell separation as of poplar. Chemical extraction and enzymatic digestion studies indicated that rhamnogalacturonan-I (RG-I), mannan and xylan contribute to cell-cell adhesion in pine wood. Mannan associated with lignin in an acidic chlorite fraction and with xylan in a dilute alkali fraction. RG-I and xylan were extracted in both chlorite and dilute alkali in poplar. Scanning electron microscopy and a probe diffusion study using Fluorescence Recovery After Photobleaching showed that lignin, RG-I and mannan initiated cell separation at cell corners and dilute alkali extraction of xylan was required for complete cell separation in pine. Cell-cell separation increased enzymatic saccharification within 24 h by 2-fold in poplar and 3.4-fold in pine. Finally, our results inform a strategy to reduce particle size in woody biomass and provide insights into different molecular bases of cell-cell adhesion.

59 BASIC BIOLOGICAL SCIENCES↗