Search NASA⌕ Search

SEARCH · Search NASA

Results for “alumina”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Compression Testing of Alumina Fiber Insulation

A series of tests were conducted to measure the response of alumina fiber insulation to compression loading. The alumina fiber insulation is a candidate gasket material for the Space Shuttle Government Furnished Equipment (GFE) Tile Overlay Repair. Tests were conducted at room temperature and 2300 F. The alumina fiber insulation is a fibrous insulation blanket which was supplied to Langley in two forms, a nominal 3 lb/ft3 version and a nominal 9 lb/ft3 version. The 3 lb/ft3 material was tested as sheets 0.15 and 0.25 inches thick and the 9 lb/ft3 material in sheets 1 inch thick. The material showed very non-linear compression behavior with the compressive resistance of the material increasing as the material was compressed. The 3 lb/ft3 0.15-inch thick material required 4.1 psi to reach the nominal installation thickness of 0.045 inches and retain a load of 2.1 lbs during unloading. Testing at 2300 F resulted in a stiffer more board-like material. The 3 lb/ft3 0.15-inch thick material retained 1 psi of compressive resistance after a 10 minute hold at 2300 F and 0.045 inches thickness.

Vaughn, Wallace L.↗
NASA NTRS2009

Moisture-Induced Alumina Scale Spallation: The Hydrogen Factor

For some time our community has been concerned with interfacial spallation of protective alumina scales, not just upon immediate cooldown, but as a time-delayed phenomenon. Moisture-induced delayed spallation (MIDS) and desktop spallation (DTS) of TBC's refer to this process. It is most apparent for relatively adherent alumina scales that have survived cool down in a dry environment, built up considerable thickness and strain energy, and have been somewhat damaged, such as by cyclic oxidation cracking. Indeed, a "sweet zone" can be defined that maximizes the observed effect as a function of all the relevant factors. Moisture has been postulated to serve as a source of interfacial hydrogen embrittlement derived from reaction with aluminum in the alloy at an exposed interface. The purpose of this monograph is to trace the close analogy of this phenomenon to other hydrogen effects, such as embrittlement of aluminides and blistering of alloys and anodic alumina films. A formalized, top-down, logic tree structure is presented as a guide to this discussion. A theoretical basis for interfacial weakening by hydrogen is first cited, as are demonstrations of hydrogen as a reaction product or detected interfacial species. Further support is provided by critical experiments that produce the same moisture effect, but by isolating hydrogen from other potential causative factors. These experiments include tests in H2-containing atmospheres or cathodic hydrogen charging.

Smialek, James L.↗
NASA NTRS2012

Alumina Based 500 C Electronic Packaging Systems and Future Development

NASA space and aeronautical missions for probing the inner solar planets as well as for in situ monitoring and control of next-generation aeronautical engines require high-temperature environment operable sensors and electronics. A 96% aluminum oxide and Au thick-film metallization based packaging system including chip-level packages, printed circuit board, and edge-connector is in development for high temperature SiC electronics. An electronic packaging system based on this material system was successfully tested and demonstrated with SiC electronics at 500 C for over 10,000 hours in laboratory conditions previously. In addition to the tests in laboratory environments, this packaging system has more recently been tested with a SiC junction field effect transistor (JFET) on low earth orbit through the NASA Materials on the International Space Station Experiment 7 (MISSE7). A SiC JFET with a packaging system composed of a 96% alumina chip-level package and an alumina printed circuit board mounted on a data acquisition circuit board was launched as a part of the MISSE7 suite to International Space Station via a Shuttle mission and tested on the orbit for eighteen months. A summary of results of tests in both laboratory and space environments will be presented. The future development of alumina based high temperature packaging using co-fired material systems for improved performance at high temperature and more feasible mass production will also be discussed.

Chen, Liang-Yu↗
NASA NTRS2014

Alumina Paste Sublimation Suppression Barrier for Thermoelectric Device

Alumina as a sublimation suppression barrier for a Zintl thermoelectric material in a thermoelectric power generation device operating at high temperature, e.g. at or above 1000K, is disclosed. The Zintl thermoelectric material may comprise Yb.sub.14MnSb.sub.11. The alumina may be applied as an adhesive paste dried and cured on a substantially oxide free surface of the Zintl thermoelectric material and polished to a final thickness. The sublimation suppression barrier may be finalized by baking out the alumina layer on the Zintl thermoelectric material until it becomes substantially clogged with ytterbia.

Paik, Jong-Ah↗
NASA NTRS2016

Electrical Performance of a High Temperature 32-I/O HTCC Alumina Package

A high temperature co-fired ceramic (HTCC) alumina material was previously electrically tested at temperatures up to 550 C, and demonstrated improved dielectric performance at high temperatures compared with the 96% alumina substrate that we used before, suggesting its potential use for high temperature packaging applications. This paper introduces a prototype 32-I/O (input/output) HTCC alumina package with platinum conductor for 500 C low-power silicon carbide (SiC) integrated circuits. The design and electrical performance of this package including parasitic capacitance and parallel conductance of neighboring I/Os from 100 Hz to 1 MHz in a temperature range from room temperature to 550 C are discussed in detail. The parasitic capacitance and parallel conductance of this package in the entire frequency and temperature ranges measured does not exceed 1.5 pF and 0.05 microsiemens, respectively. SiC integrated circuits using this package and compatible printed circuit board have been successfully tested at 500 C for over 3736 hours continuously, and at 700 C for over 140 hours. Some test examples of SiC integrated circuits with this packaging system are presented. This package is the key to prolonged T greater than or equal to 500 C operational testing of the new generation of SiC high temperature integrated circuits and other devices currently under development at NASA Glenn Research Center.

dielectric performance↗
DOE OSTI2023

Solution combustion synthesis of iron-based alumina catalysts for dehydrogenation of fossil fuels

Microwave-assisted thermocatalytic dehydrogenation of fossil fuels has been proposed as a method for hydrogen production with no CO2 emissions. The byproduct is carbon, which has a commercial value. Iron-based alumina nanocomposites are promising catalysts for this process as they both absorb microwave radiation and catalyze the dehydrogenation. In addition, they may have magnetic properties, which could be used for their separation from the carbon byproduct. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of iron-based alumina nanocomposites because it can produce high specific surface area oxides in a facile manner. However, the effects of the heating mode, the fuel, and the iron/aluminum ratio on the combustion synthesis behavior and the product properties have not been studied yet. In the present work, the iron-based alumina nanocomposites were obtained by SCS using a hotplate, a muffle furnace, and a microwave oven. The initial mixtures were aqueous solutions of iron nitrate, aluminum nitrate, and an organic fuel. The concentrations of the two nitrates were varied in proportion to Fe:Al molar ratios of 1:2, 1:1, and 2:1. Two fuels were tested: citric acid and glycine. The combustion was less vigorous when citric acid was used as the fuel, which is explained by the lower exothermicity of the reaction. X-ray diffraction analysis of the products confirmed the formation of complex oxides of Fe and Al, specifically it detected hercynite and magnetite phases. Brunauer-Emmett-Teller surface area analysis has shown that the powders obtained using citric acid have specific surface areas as high as 276 m2/g, significantly higher than those obtained using glycine. Muffle furnace and hotplate heating led to comparable specific surface areas, while microwave heating resulted in significantly lower specific surface areas. The magnetic properties of the products increase with increasing the Fe/Al molar ratio from 1:2 (no response to a magnetic field) to 1:1 (weak response) and 2:1 (strong response).

solution combustion synthesis, nanoscale oxides, f↗
DOE OSTI2022

Solution combustion synthesis of iron-based alumina nanocomposites for clean production of hydrogen from fossil fuels

Iron-based alumina nanocomposites are promising materials for microwave-assisted thermocatalytic dehydrogenation of fossil fuels, which has been proposed for the production of hydrogen with no CO2 emissions. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of these materials because it has been used for synthesis of many nanoscale oxides. However, SCS can be carried out using different organic fuels and different heating equipment, and it is important to determine which fuel and heating mode generate materials with the best properties for dehydrogenation, such as maximized specific surface area. In the present work, the iron-based alumina nanocomposites were obtained by SCS using two different fuels (citric acid and glycine) and two different heating modes (a hotplate and a muffle furnace). The precursors/oxidizers were iron nitrate and aluminum nitrate. They were mixed with the fuel according to stoichiometry and dissolved in water. Heating the solution resulted in combustion synthesis. The products were characterized by X-ray diffraction analysis, Brunauer-Emmett-Teller surface area analysis, laser diffraction particle size analysis, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The experiments have shown that the specific surface area of the iron-based alumina nanocomposites obtained by SCS can be dramatically increased by using citric acid instead of glycine, and additionally by using a muffle furnace instead of a hotplate.

Solution combustion synthesis, Nanoscale metal oxi↗
DOE OSTI2025

All-alumina quarter-wave plate coatings fabricated by glancing angle deposition using serial bideposition

Anisotropic phase retarders, used in high power laser facilities to perform polarization smoothing, can be obtained by the glancing angle deposition (GLAD) coating process. Due to its high laser resistance, the coatings are mainly made of silica. Therefore, limited attention has been given to other dielectric materials. Here we present a study on alumina GLAD anisotropic coatings; a material with high laser resistance, higher birefringence and lower environmental sensitivity than silica. Since the anisotropy is related to the coatings microstructure through the deposition angle, samples were coated at angles varying from ± 68° to ± 82° using the serial bideposition technique. They were characterized by ellipsometry, polarimetry, spectrophotometry and electron microscopy. We showed that the highest birefringence is obtained at a deposition angle of ± 76° with an in-plane value of 0.053. Based on these results, a quarter-wave plate at 351 nm was designed as a multilayer with seven pairs of anisotropic layers deposited at ± 76° and isotropic layers deposited at 0°. The fabricated coating exhibited a uniform retardance of 88.51 ± 0.45 nm. The alumina GLAD wave plates presented here, open the door to new possibilities in the laser field and especially in the field of fusion energy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Superhydrophilicity of $α$-alumina surfaces results from tight binding of interfacial waters to specific aluminols

Understanding the microscopic driving force of water wetting is challenging and important for design of materials. The relations between structure, dynamics and hydrogen bonds of interfacial water can be investigated using molecular dynamics simulations. Here, contact angles at the alumina (0001) and ($11\bar{2}0$) surfaces are studied using both classical molecular dynamics simulations and experiments. To test the superhydrophilicity, the free energy cost of removing waters near the interfaces are calculated using the density fluctuations method. The strength of hydrogen bonds is determined by their lifetime and geometry. Both surfaces are superhydrophilic and the (0001) surface is more hydrophilic. Interactions between surfaces and interfacial waters promote a templating effect whereby the latter are aligned in a pattern that follows the underlying lattice of the surfaces. Translational and rotational dynamics of interfacial water molecules are slower than in bulk water. Hydrogen bonds between water and both surfaces are asymmetric, water-to-aluminol ones are stronger than aluminol-to-water ones. Molecular dynamics simulations eliminate the impacts of surface contamination when measuring contact angles and the results reveal the microscopic origin of the macroscopic superhydrophilicity of alumina surfaces: strong water-to-aluminol hydrogen bonds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Computational study of the adsorption of bimetallic clusters on alumina substrate

We performed computational investigation of the adsorption of bimetallic Pd 3 M 2 (where M changes from Ag, Au, Co, Cu, Mn, Ni, Pt, and Ru) cluster on the hydroxylated alumina surface. Previously, it was shown that small silver cluster can control the rate of discharge at the cathode of lithium-oxygen battery. The gap near the fermi energy was shown to control the oxygen reduction, an important reaction for LiO 2 formation. Controlling the gap would ultimately control the rate of LiO 2 formation. One can vary the size of the cluster to vary the gap, however, this "knob" provides limited variance in the gap. Alloying, in combination with size variation offer a much wider control of the gap, hence the LiO 2 formation. Using Density Functional Theory (DFT), we determined the most stable geometry of the bimetallic clusters Pd 3 M 2 and calculated the binding energies of these clusters on the alumina substrate which ranges from 0.2 eV to 0.25 eV depending upon the composition of the alloy-cluster, its orientation and the adsorption site. We also find that Pd atoms bind strongly with the substrate oxygen atoms with an average short bond-length of about 2.2 angstrom. We explored how the gap at the Fermi level of the system varies as a function of elemental composition and the calculated gap ranges from 0 meV to 90 meV. Charges distribution using Bader analysis was also performed to probe how charges are transferred between the cluster and the substrate. These preliminary results will open the door for more systematic studies of alloy clusters of different size and stoichiometry for Li-O 2 battery cathode design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Sequential Infiltration Synthesis of Bilayer Porous Alumina Nanostructures for Broad-Angle, Broadband Antireflective Coatings

Antireflective coatings (ARCs) are thin films engineered to reduce light reflections. Delivering broadband, wide-angle performance is essential for photovoltaics, imaging, and sensing, yet truly omnidirectional antireflection remains difficult due to angle-dependent optical paths and a narrow palette of suitable refractive indices. Here, in this study, we systematically investigate an emerging class of multilayer inorganic ARCs based on conformally coated nanoporous alumina templated by intrinsically microporous polymers (PIMs) and block copolymers (BCPs). We establish a design framework that maps thickness reflectance relationships to identify thickness pairs minimizing reflection across wavelength and incidence angle. We show that deliberately separating the local reflectance minima of the top and bottom layers in bilayer nanostructures broadens the antireflective bandwidth and angular range. We show that 235-nm single-side bilayer porous alumina nanostructures achieves under 2 % reflectance from 380–750 nm for incidence angles up to 45° with less than 0.6% reflectance for incidence angles under 20°. The approach is readily extensible to additional layers or materials with refractive indices tuned via templated nanoporosity and composition, enabling practical, etch-free ARC fabrication without HF or fluorinated precursors and advancing straightforward design of broadband, wide-angle (quasi-omnidirectional) ARCs for next-generation optical systems.

antireflective coatings↗
DOE OSTI2023

Activity of Silica-Alumina for the Conversion of Polyethylene into Tunable Aromatics Below Pyrolytic Temperatures

Plastic waste is a mounting problem that lacks global strategy, largely due to inadequate recycling capabilities. One alternative gaining traction in the heterogeneous catalysis community is the upcycling of polyolefins into value-added products, such as hydrogen-free conversion to alkylaromatic compounds over Pt/Al 2 O 3 . Here, we examined the activity of nominally metal-free, mesoporous silica-alumina mixed oxide materials (SiO 2 –Al 2 O 3 ) for the conversion of polyethylene into aromatic compounds at temperatures of and below 280 °C. Yields with the silica-alumina catalysts are comparable to those obtained over Pt(1 wt %)/Al 2 O 3 under identical conditions, and product selectivity can be tuned by altering reaction conditions or the acid site density of the SiO 2 –Al 2 O 3 . Notably, the fraction of polyaromatic products increases with the Brønsted acid site density of the catalyst, as does the degree of polymer deconstruction. These catalysts can be reused without regeneration, and their activity improves with each recycling event, producing soluble product yields up to 83%. Preliminary work on the mechanism of the reaction suggests that acid sites are responsible for initiating depolymerization and aromatization reactions, in analogy to previous work in the literature. Finally, this work showcases the activity of SiO 2 –Al 2 O 3 for polyolefin deconstruction/aromatization at subpyrolytic temperatures and lays the foundation for future studies involving solid acid and bifunctional catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Flexural strength of a conventionally processed and additively manufactured debased 94% alumina

Mechanical strength of a 94 wt% debased alumina was measured using ASTM-C1161 specimens fabricated via conventional and lithography-based ceramic manufacturing (LCM) methods. The effects of build orientation and a 1500°C wet hydrogen fire added to the LCM firing sequence on strength were evaluated. Additionally, a Weibull fit to the conventional flexural specimen data yielded 20 and 356 MPa for the modulus and characteristic strength, respectively. Weibull fits of the data from the LCM specimens yielded moduli between 7.5 and 11.3 and characteristics strengths between 333 and 339 MPa. A Weibull fit to data from LCM specimens subjected to the wet hydrogen fire yielded 14.2 and 376 MPa for the modulus and characteristic strength, respectively. The 95% confidence intervals for all Weibull parameters are reported. Average Archimedes bulk densities of LCM and conventional specimens were 3.732 and 3.730 g/cm 3 , respectively. Process dependent differences in surface morphology were observed in scanning electron microscope (SEM) images of specimen surfaces. SEM images of LCM specimen cross-sections showed alumina grain texture dependent on build direction, but no evidence of porosity concentrated in planes between printed layers. Fracture surfaces of LCM and conventionally processed specimens revealed hackle lines and mirror regions indicative of fracture initiation at the sample surface rather than the interior.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Micropatterning of alumina tubular membranes via laser carving for enhanced direct air capture

An approach for preparing and applying micropatterned alumina tubular membranes was developed for improved gas-liquid contact at low air pressure drop in direct air capture application. The paper demonstrated that the laser carving of micropatterns on the outer surface of the alumina tubular membranes could greatly increase their outer surface area and enhance gas-liquid turbulence for a reduced diffusion mass transfer resistance. Six kinds of micropattern configurations were fabricated and studied, including random and regular micropatterns. By introducing a 500-μm solid grid micropattern, the outer surface area doubles and enhances carbon dioxide capture efficiency from 61% to 97% after the membrane was hydrophobically modified with fluoroalkylsilane. Here, the air pressure drop through the tube lumen remained low even when the packing density increased from 382 to 906 m 2 /m 3 . The liquid entry pressure of this micropatterned membrane was the same after testing for 220 h running with the help of periodic drying.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Cast Alumina-Forming Austenitic Stainless Steels for High Temperature Heat Treatment Furnace Rolls

Alloy developers worldwide have struggled to create creep-resistant alumina-forming, iron-based austenitic stainless steels for use as high-temperature structural alloys, but with limited success in balancing alloy cost, oxidation, and creep resistance. Here, this article describes the research and development of a novel cast alumina-forming austenitic stainless steel. This work won the prestigious Engineering Materials Achievement Award presented at IMAT 2023 in Detroit.

36 MATERIALS SCIENCE↗
NASA NTRS1996

High Temperature Stability of Potassium Beta Alumina

None. From Objectives section: Evaluate the stability of potassium beta alumina under potassium AMTEC operating conditions. Evaluate the stability regime in which potassium beta alumina can be fabricated.

potassium beta aluminum AMTEC potassium AMTEC oper↗
DOE OSTI2024

Alumina – Stabilized SEI and CEI in Potassium Metal Batteries

Aluminum oxide (Al 2 O 3 ) nanopowder is spin-coated onto both sides of commercial polypropene separator to create artificial solid-electrolyte interphase (SEI) and artificial cathode electrolyte interface (CEI) in potassium metal batteries (KMBs). Here, this significantly enhances the stability, including of KMBs with Prussian Blue (PB) cathodes. For example, symmetric cells are stable after 1,000 cycles at 0.5 mA/cm 2 –0.5 mAh/cm 2 and 3.0 mA/cm 2 –0.5 mAh/cm 2 . Alumina modified separators promote electrolyte wetting and increase ionic conductivity (0.59 vs. 0.2 mS/cm) and transference number (0.81 vs. 0.23). Cryo-stage focused ion beam (cryo-FIB) analysis of cycled modified anode demonstrates dense and planar electrodeposits, versus unmodified baseline consisting of metal filaments (dendrites) interspersed with pores and SEI. Alumina-modified CEI also suppresses elemental Fe crossover and reduces cathode cracking. Mesoscale modeling of metal – SEI interactions captures crucial role of intrinsic heterogeneities, illustrating how artificial SEI affects reaction current distribution, conductivity and morphological stability.

25 ENERGY STORAGE↗
DOE OSTI2024

Ability of x‐ray computed tomography to resolve critical flaw size in laser‐based, paste stereolithography ceramic printing of alumina

Abstract Complex alumina parts were printed using vat photopolymerization (VPP), which is a stereolithography‐based additive manufacturing (AM) technique used to shape ceramic preforms, or green parts. The critical flaw size was determined using classical fracture mechanics techniques. The strength and fracture toughness were measured and compared to flaws detected in x‐ray computed tomography (XCT or CT) distributions as well as the fracture surfaces. The strength was lower compared traditionally made alumina, and that is due to layering effects, slurry defects, and printing defects. The critical flaw size from fracture mechanics was 206 µm. XCT has high enough resolution to detect the critical flaw size and much smaller features, where the average flaw size observed in CT scans was around 80–100 µm. The fracture surfaces indicate that flaws causing failure are larger than that of the critical flaw size (∼300 µm), but fracture surfaces do not show definitive features compared to traditionally made ceramics. Since XCT can observe flaws smaller than the critical flaw size, this method can be used as a screening technique.

36 MATERIALS SCIENCE↗