Search NASA⌕ Search

SEARCH · Search NASA

Results for “amorphous alloys”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Stress-Dependent Chemo-Mechanical Performance of Amorphous Si Anodes for Li-Ion Batteries upon Lithiation

Alloying-type anodes are significantly governed by their chemo-mechanical performance during the electrochemical cycling. The reaction-induced huge volumetric change of these anodes may cause material degradation and failure under mechanical constraints. Here, we investigate the stress-dependent lithiation behavior of amorphous Si (a-Si) anodes using molecular dynamics simulations. It is indicated that a-Si anodes can sustain higher hydrostatic stress than biaxial/uniaxial ones without the occurrence of mechanical failure. Thermodynamic and electrochemical calculations demonstrate that although the lithiation procedure also affects the thermodynamic stability of a-Si anodes, it is mainly dominated by the external mean stresses. Compressive stress is confirmed to destabilize a-Si anodes and further trigger their capacity fading. Compared with our atomistic simulations, previous continuum models underestimate the open-cell potentials of a-Si anodes, due to their ignored large volumetric deformation at higher stresses and Li concentrations. Finally, this computational study provides the intensive atomic-level understanding of the stress-dependent lithiation behavior of a-Si anodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Electrical and structural properties of binary Ga–Sb phase change memory alloys

Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.

Ume, Rubab (ORCID:0000000324766900)↗
DOE OSTI2021

Phase-field modeling of the interactions between an edge dislocation and an array of obstacles

Obstacles, such as voids and precipitates, are prevalent in crystalline materials. They strengthen crystals by serving as barriers to dislocation glide. Here in this work, we develop a phase-field dislocation dynamics (PFDD) technique for investigating the interactions between dislocations and second-phase obstacles, which can be either voids or precipitates. The PFDD technique is constructed to account for elastic heterogeneity, elastic anisotropy, dissociation of the dislocation, and dislocation transmission across bicrystalline interfaces. Within the framework, we present a model for “pseudo-voids”, which are voids shearable by dislocations, in contrast to unphysical, unshearable voids in conventional phase-field dislocation formulations. We employ the PFDD technique to investigate the in-plane interactions between an edge dislocation and an array of nano-scale obstacles with different spacings. In this application, the interactions take place in glide planes of either a face-centered cubic (FCC) Cu or a body-centered cubic (BCC) Nb matrix, while the precipitates have a Cu 1-x Nb x composition, with x varying from 0.1 to 0.9. Our atomistic simulations find that the alloy precipitates can have an FCC, an amorphous, or a BCC phase, depending on the compositional ratio between Cu and Nb, i.e., value of x. Among all types of obstacles, the critical stresses for dislocation bypass are the highest for unshearable amorphous precipitates, followed by shearable crystalline precipitates, and then the pseudo-voids.

42 ENGINEERING↗
DOE OSTI2022

Multi-principal element grain boundaries: Stabilizing nanocrystalline grains with thick amorphous complexions

Amorphous complexions have recently been demonstrated to simultaneously enhance the ductility and stability of certain nanocrystalline alloys. In this study, three quinary alloys (Cu–Zr–Hf–Mo–Nb, Cu–Zr–Hf–Nb–Ti, and Cu–Zr–Hf–Mo–W) are studied to test the hypothesis that increasing the chemical complexity of the grain boundaries will result in thicker amorphous complexions and further stabilize a nanocrystalline microstructure. Significant boundary segregation of Zr, Nb, and Ti is observed in the Cu–Zr–Hf–Nb–Ti alloy, which creates a quaternary interfacial composition that limits average grain size to 63 nm even after 1 week at ~ 97% of the melting temperature. This high level of thermal stability is attributed to the complex grain boundary chemistry and amorphous structure resulting from multi-component segregation. Furthermore, high-resolution transmission electron microscopy reveals that the increased chemical complexity of the grain boundary region in the Cu–Zr–Hf–Nb–Ti alloy results in an average amorphous complexion thickness of 2.44 nm, approximately 44% and 32% thicker than amorphous complexions previously observed in Cu–Zr and Cu–Zr–Hf alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of High Bs Fe-Ni Based Metal Amorphous Nanocomposite by Optimization of Glass Forming Ability

A growing interest in electric vehicles challenges soft magnetic materials to improve efficiency and power density. Metal amorphous nanocomposites (MANCs) have lower coercivities and eddy current losses, allowing for greater efficiency and higher switching frequency. The later allows for high motor speeds and improved power density. However, commercially available and laboratory demonstrated MANCs have shortcomings. Fe-based MANCs, such as FINEMET have excellent magnetic properties, but mechanical properties limit their application in high speed electric motors (HSMs). Fe-Co based MANCs, such as HITPERM, have high saturation inductions and good mechanical properties, but elevated magnetostrictive losses. Co-based MANCs and more recent Fe-Ni based MANCs have low losses and good mechanical properties, but lower saturation inductions (1-1.2 T), that limit power density in HSMs. Recently, much work has explored improving saturation induction in MANCs by increasing the content of magnetic elements, which comes at the cost of glass-forming ability (GFA). These efforts where generally limited to trial and error testing. Additionally, all work to date has focused on Fe-based alloys. In this work, a method of using Thermocalc simulation to locate near-eutectic compositions has been applied to Fe-Ni based alloys. Minima in liquidus temperature and solidification range were found for a ternary composition range and used to identify compositions that retain good GFA as the percentage of magnetic elements is increased. The (Fe 70 Ni 30 ) x (B-Si-Nb) 100-x alloy system for x=82% and x=85% was explored by Thermocalc simulations. This is an increase in magnetic element content compared to previously developed x=80% alloys. 3 compositions in the x=82% system, and 1 alloy in the x=85% system where identified and successfully cast as amorphous ribbon. The amorphous nature of the ribbon was confirmed by a bend test and XRD. Magnetic testing was performed by PPMS to measure saturation induction and Curie temperature of the amorphous material. The Curie temperatures increased to 407-438 °C for the x=82% alloys, and 462 °C for the x=85% alloy. Saturation induction increased to 1.28-1.36 T for the x=82% alloy and 1.48 T for the x=85% alloy, which is a significant improvement over the ~370 °C Curie temperature and 1.2 T saturation of previous Fe-Ni alloy. Crystallization behavior was studied by XRD for the x=85% alloy, showing that crystallization process follows a 2-step process of Amorphous → BCC+FCC+Amorphous → BCC+FCC+Fe 3 B+Fe 23 B 6 . Post annealing magnetic properties were studied by strip testing, and saturation induction as high as 1.48 T was seen after optimal annealing. TEM was used to study structure of as cast and annealed material. 2 alloys with x=82% compositions were identified with an optimal crystalline size of 10-20 nm, while the x=85% alloy had this structure in the as cast state. This opens the possibility of using the alloy in the as cast state, without requiring annealing. In conclusion, alloys with good GFA and improved magnetic properties were identified by Thermocalc simulation.

Krimer, Yuval↗
DOE OSTI2021

Development of high B s Fe–Ni-based metal amorphous nanocomposite by optimization of glass-forming ability

Thermocalc simulations identified compositions with good glass-forming ability (GFA) by locating minima in liquidus temperature, and solidification range in (Fe 70 Ni 30 ) x (B-Si-Nb) 100-x alloys with x = 82% and x = 85%, increased compared to previously developed x = 80% alloys. 3 compositions in the x = 82% system and 1 in the x = 85% system were successfully cast as amorphous magnetic ribbon. Magnetic properties of as-cast alloys showed improvements in Curie temperature and saturation induction, especially for the 85% alloy. Crystallization behavior in the 85% alloy was determined to occur as a 2-step process. Annealing studies showed (Fe 70 Ni 30 ) 82 Nb 2 Si 0 B 16 and (Fe 70 Ni 30 ) 82 Nb 3 Si 0 B 15 alloys to exhibit low coercivity and high B s with annealing. TEM results show significant crystallization in as-cast ribbon. The (Fe 70 Ni 30 ) 85 Nb 0.5 Si 0 B 14.5 alloy as-cast has small, uniformly distributed grains, allowing a useful nanocrystalline alloy to be produced as cast. Lastly, the parameter ΔT xg , the temperature range in which the material can be thermomechanically processed, was in the range of 12–23 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Amorphous complexion-aided sintering enables scalable processing of bulk nanocrystalline Cu-Zr with high strength and compressive plasticity

Nanocrystalline alloys can have exceptional strengths, yet due to limited microstructural stability it is difficult to fabricate bulk pieces through traditional processing routes that retain nanosized grains. In this study, centimeter-sized Cu-Zr alloy pellets were fabricated via a simple and improved powder metallurgy processing route. Different consolidation temperatures and times were employed to investigate the effect of amorphous grain boundary complexions on densification and the resulting mechanical properties. Bulk compression tests were carried out, with the samples that were hot pressed at 900 °C for 10 h exhibiting an excellent combination of average yield strength of 722 ± 45 MPa and average failure strain of 25.3 ± 2.4 %. Furthermore, we find that a powder processing route which enables amorphous complexion-assisted sintering leads to samples that (1) reach full density without requiring quenching treatments or other complex processing, (2) demonstrate appreciable plasticity, and (3) have strength that competes with commercially available high-strength Cu alloys.

Bulk nanocrystalline alloy↗
DOE OSTI2023

Universal and interpretable classification of atomistic structural transitions via unsupervised graph learning

Materials processing often occurs under extreme dynamic conditions leading to a multitude of unique structural environments. These structural environments generally occur at high temperatures and/or high pressures, often under non-equilibrium conditions, which results in drastic changes in the material's structure over time. Computational techniques, such as molecular dynamics simulations, can probe the atomic regime under these extreme conditions. However, characterizing the resulting diverse atomistic structures as a material undergoes extreme changes in its structure has proved challenging due to the inherently non-linear relationship between structures as large-scale changes occur. Here, we introduce SODAS++, a universal graph neural network framework, that can accurately and intuitively quantify the atomistic structural evolution corresponding to the transition between any two arbitrary phases. We showcase SODAS++ for both solid–solid and solid–liquid transitions for systems of increasing geometric and chemical complexity, such as colloidal systems, elemental Al, rutile and amorphous TiO 2 , and the non-stoichiometric ternary alloy Ag 26 Au 5 Cu 19 . Finally, we show that SODAS++ can accurately quantify all transitions in a physically interpretable manner, showcasing the power of unsupervised graph neural network encodings for capturing the complex and non-linear pathway, a material's structure takes as it evolves.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Determining the three-dimensional atomic structure of an amorphous solid

Amorphous solids such as glass, plastics and amorphous thin films are ubiquitous in our daily life and have broad applications ranging from telecommunications to electronics and solar cells 1-4 . However, owing to the lack of long-range order, the three-dimensional (3D) atomic structure of amorphous solids has so far eluded direct experimental determination 5-15 . Here we develop an atomic electron tomography reconstruction method to experimentally determine the 3D atomic positions of an amorphous solid. Using a multi-component glass-forming alloy as proof of principle, we quantitatively characterize the short- and medium-range order of the 3D atomic arrangement. We observe that, although the 3D atomic packing of the short-range order is geometrically disordered, some short-range-order structures connect with each other to form crystal-like superclusters and give rise to medium-range order. We identify four types of crystal-like medium-range order-face-centred cubic, hexagonal close-packed, body-centred cubic and simple cubic-coexisting in the amorphous sample, showing translational but not orientational order. These observations provide direct experimental evidence to support the general framework of the efficient cluster packing model for metallic glasses 10,12-14,16 . Finally, we expect that this work will pave the way for the determination of the 3D structure of a wide range of amorphous solids, which could transform our fundamental understanding of non-crystalline materials and related phenomena.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Structural Studies of Alloyed and Nanoparticle Transition Metal Dichalcogenides by Selenium-77 Solid-State Nuclear Magnetic Resonance Spectroscopy

Layered transition metal dichalcogenides (TMDCs) such as MoS 2 , MoSe 2 , and WSe 2 are under intense investigation because they are atomically thin semiconductors with photophysical properties that can be tuned by changing their composition or morphology. Mechanochemical processing has been proposed as a method to obtain alloyed TMDCs in the series Mo 1–x W x S y Se 2–y (x = 0–1; y = 0–2). However, elucidating the chemical transformations occurring at the atomic scale following mechanochemical processing can be challenging because the products are often amorphous or microcrystalline. To address this challenge, we probe TMDC mixing and alloying by using a combination of powder X-ray diffraction, Raman spectroscopy, diffuse reflectance spectroscopy, 77 Se solid-state nuclear magnetic resonance (SSNMR) spectroscopy, and planewave density functional theory (DFT) calculations. The nature of the milling material and reaction atmosphere are shown to be essential factors in limiting the formation of undesired oxide byproducts. We demonstrate acquisition of 77 Se SSNMR spectra using different combinations of Carr-Purcell Meiboom-Gill acquisition (CPMG) pulse sequences, magic angle spinning (MAS), and MAS dynamic nuclear polarization. Further, the combination of SSNMR with the other characterization methods clearly demonstrates that high energy impact ball milling induces molecular level alloying of Mo, W and chalcogen atoms in the family Mo 1–x W x S y Se 2–y . Gauge including projector augmented wave DFT calculations yield accurate 77 Se chemical shift (CS) tensor components. 77 Se SSNMR spectroscopy was also applied to study the structure of WSe 2 nanocrystals intercalated with ethylenediamine. The intercalated WSe 2 nanocrystals exhibit a more positive isotropic 77 Se CS as compared to bulk WSe 2 , however, the 77 Se CS anisotropy is the same, confirming the WSe 2 layers have a similar structure as in their bulk counterparts.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Regulating the Third Metal to Design and Engineer Multilayered NiFeM (M: Co, Mn, and Cu) Nanofoam Anode Catalysts for Anion-Exchange Membrane Water Electrolyzers

In this study, alkaline anion-exchange membrane water electrolyzers (AEMWEs) for green hydrogen production have received intensive attention due to their feasibility of using earth-abundant platinum group metal (PGM)-free catalysts. Herein, the third metal is incorporated into NiFe-based catalysts to regulate their electronic structures and morphologies, aiming to achieve sufficient oxygen evolution reaction (OER) activity and performance in AEMWEs. The ternary NiFeM (M: Cu, Co, or Mn) catalysts are featured with multiple layered structures and nanofoam network morphologies, consisting of highly OER-active amorphous Ni-rich oxide shells and electrically conductive metallic alloy cores. The physical and electronic perturbations to the NiFe induced by a third element lead to a fine-tuning of the redox ability of the metal sites at the reaction centers, which breaks the scaling relationship between OH* and O* intermediates at the reaction centers. Thus, the unique structural configuration and electronic regulation simultaneously benefit catalytic activity and performance improvements. These NiFeM nanofoam catalysts demonstrated promising anode performance in actual AEMWEs, comparable to the IrO 2 reference, especially at high current densities. Notably, using various electrolytes (e.g., KOH solution or pure water) for AEMWEs exhibited a different performance trend among studied NiFeM catalysts, likely due to dynamic changes of catalysts under various OER environments.

25 ENERGY STORAGE↗
DOE OSTI2025

Spectral Performance of Multilayer Amorphous Selenium and Selenium–Tellurium Photodetectors

The ability to robustly and with scalability detect single photons in the visible spectrum with wavelength resolution would transform many imaging applications. Theoretical studies propose an array of carbon nanotubes (CNTs) functionalized with semiconductor quantum dots (QDs) as a physical realization of such photon sensors. In this work, we report approaches to synthesize these CNT-QD nanostructures using DNA as a smart glue to connect CNTs to QDs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The emergence of small-scale self-affine surface roughness from deformation

Most natural and man-made surfaces appear to be rough on many length scales. There is presently no unifying theory of the origin of roughness or the self-affine nature of surface topography. One likely contributor to the formation of roughness is deformation, which underlies many processes that shape surfaces such as machining, fracture, and wear. Using molecular dynamics, we simulate the biaxial compression of single-crystal Au, the high-entropy alloy Ni 36.67 Co 30 Fe 16.67 Ti 16.67 , and amorphous Cu 50 Zr 50 and show that even surfaces of homogeneous materials develop a self-affine structure. By characterizing subsurface deformation, we connect the self-affinity of the surface to the spatial correlation of deformation events occurring within the bulk and present scaling relations for the evolution of roughness with strain. These results open routes toward interpreting and engineering roughness profiles.

42 ENGINEERING↗
DOE OSTI2021

Phase transformations, microstructural refinement and defect evolution mechanisms in Al-Si alloys under non-hydrostatic diamond anvil cell compression

Non-hydrostatic compression of materials using a diamond anvil cell (DAC) can transform equilibrium microstructure of an alloy to novel, potentially metastable states. In this study, in situ synchrotron X-ray diffraction (XRD) during compression up to 24 GPa and subsequent ex situ, high resolution analytical electron microscopy (AEM) after decompression of an Al-Si alloy provided insight into the crystallographic changes during the compression as well as microstructural refinement, and defect structures caused by such a high pressure compression-decompression process. Pressure resolved in-situ synchrotron XRD was used to detail the phase transformation pathway of the eutectic Si phase in Al-Si alloy, from Si-I → Si-XI → Si-V during compression, and a final transformation predominantly to Si-III after decompression. Using scanning and transmission electron microscopy (S/TEM), site specific analysis of the alloy immediately underneath the anvil contact surface demonstrated a highly complex microstructure. A narrow region of thick amorphous Al oxide interspersed with nanocrystalline grains was found at the top surface. Underneath this Al oxide, while the majority the eutectic Si was transformed into highly-deformed, polycrystalline (PC) Si-III, a complex intermediate layer was discovered at the interface between Al and Si, comprised of a small fraction of Al nanocrystals and a majority of nanocrystalline Si-I. This combination of pressure resolved in-situ synchrotron XRD coupled with subsequent high resolution, electron microscopy resolved the phase transformation as well as non-equilibrium microstructures in a metallic alloy induced by a non-hydrostatic high pressure compression followed by decompression.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electrodeposition of Complex High Entropy Oxides via Water Droplet Formation and Conversion to Crystalline Alloy Nanoparticles

We report that a combination of electrodeposition and thermal reduction methods have been utilized for the synthesis of ligand-free FeNiCo alloy nanoparticles through a high-entropy oxide intermediate. These phases are of great interest to the electrocatalysis community, especially when formed by a sustainable chemistry method. This is successfully achieved by first forming a complex five element amorphous FeNiCoCrMn high-entropy oxide (HEO) phase via electrodeposition from a nanodroplet emulsion solution of the metal salt reactants. The amorphous oxide phase is then thermally treated and reduced at 570–600 °C to form the crystalline FeNiCo alloy with a separate CrMnO x cophase. The FeNiCo alloy is fully characterized by scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy elemental analysis and is identified as a face-centered cubic crystal with the lattice constant a = 3.52 Å. The unoptimized, ligand-free FeNiCo NPs activity toward the oxygen evolution reaction is evaluated in alkaline solution and found to have an ~185 mV more cathodic onset potential than the Pt metal. Beyond being able to synthesize highly crystalline, ligand-free FeNiCo nanoparticles, the demonstrated and relatively simple two-step process is ideal for the synthesis of tailor-made nanoparticles where the desired composition is not easily achieved with classical solution-based chemistries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

An energetic link between order and strength in metals: A nanocrystalline strength limit in high-entropy alloys and intermetallic compounds

The metallurgy and materials communities have long understood and exploited fundamental links between chemical and structural ordering in metallic solids to tailor their mechanical properties. We extend these ideas to include prediction of the nanocrystalline strength limit in high-entropy alloys and intermetallic compounds, where a breakdown occurs in the classical Hall-Petch strengthening behavior. The highest reported strength achievable through alloying has rapidly climbed and given rise to new classifications of materials with extraordinary properties, with a notable case being nanocrystalline metals. High-entropy alloys (chemically disordered, concentrated solid solutions) and intermetallic compounds are two boundary cases of how tailored order can be used to manipulate mechanical behavior. Here, we show that the complex electronic-structure mechanisms governing the peak strength of alloys and pure metals can be reduced to a few physically meaningful parameters based on their atomic arrangements and used – with no fitting parameters – to predict the maximum strength of these materials. This includes a generalized energy-based accounting for the degree of structural and chemical ordering that allows for rapid and reasonably accurate prediction of peak strength (validated in the nanocrystalline limit) as a function of temperature. Predictions of maximum strength based on the activation energy (with all materials properties derived from DFT calculations or experiments) for a stress-driven transition to an amorphous state is shown to accurately describe the breakdown in Hall-Petch behavior at the smallest crystallite sizes for pure metals, intermetallic compounds, high-entropy alloys, and metallic glasses. Further, this activation energy is also shown to be directly proportional to interstitial electronic charge density, which is a good predictor of ductility, stiffness (moduli), and phase stability in high-entropy alloys and solid metals generally. The proposed framework suggests the possibility of coupling ordering and intrinsic strength to mechanisms like dislocation nucleation, hydrogen embrittlement, and transport properties, such as through correlations between the activation energies for amorphization with stacking-fault and grain boundary energies. It additionally opens the prospect for greatly accelerated structural materials design and development to address materials challenges limiting more sustainable and efficient use of energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Kinetics of amorphous defect phases measured through ultrafast nanocalorimetry

Recognition of the role of extended defects on local phase transitions has led to the conceptualization of the defect phase, localized thermodynamically stable interfacial states that have since been applied in a myriad of material systems to realize significant enhancements in material properties. Here, we explore the kinetics of grain boundary confined amorphous defect phases, utilizing the high temperature and scanning rates afforded by ultrafast differential scanning calorimetry to apply targeted annealing/quenching treatments at high rates capable of capturing the kinetic behavior. Four Al-based nanocrystalline alloys, including two binary systems, Al–Ni and Al–Y, and two ternary systems, Al–Mg–Y and Al–Ni–Y, are selected to probe the materials design space (enthalpy of mixing, enthalpy of segregation, chemical complexity) for amorphous defect phase formation and stability, with correlative transmission electron microscopy applied to link phase evolution and grain stability to nanocalorimetry signatures. A series of targeted isothermal annealing heat treatments is utilized to construct a Time–Temperature-Transformation curve for the Al–Ni system, from which a critical cooling rate of 2400 °C/s was determined for the grain boundary confined disordered-to-ordered transition. Finally, a thermal profile consisting of 1000 repeated annealing sequences was created to quantify the recovery of the amorphous defect phase following sequential annealing treatments, with results indicating remarkable microstructural stability after annealing at temperatures above 90% of the melting temperature. This work contributes to a deeper understanding of grain boundary localized thermodynamics and kinetics, with potential implications for the design and optimization of advanced materials with enhanced stability and performance.

Amorphous defect phases↗