Search NASA⌕ Search

SEARCH · Search NASA

Results for “and lower operating pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Zero Gravity Cryogenic Vent System Concepts for Upper Stages

The capability to vent in zero gravity without resettling is a technology need that involves practically all uses of sub-critical cryogenics in space. Venting without resettling would extend cryogenic orbital transfer vehicle capabilities. However, the lack of definition regarding liquid/ullage orientation coupled with the somewhat random nature of the thermal stratification and resulting pressure rise rates, lead to significant technical challenges. Typically a zero gravity vent concept, termed a thermodynamic vent system (TVS), consists of a tank mixer to destratify the propellant, combined with a Joule-Thomson (J-T) valve to extract thermal energy from the propellant. Marshall Space Flight Center's (MSFC's) Multipurpose Hydrogen Test Bed (MHTB) was used to test both spray bar and axial jet TVS concepts. The axial jet system consists of a recirculation pump heat exchanger unit. The spray bar system consists of a recirculation pump, a parallel flow concentric tube, heat exchanger, and a spray bar positioned close to the longitudinal axis of the tank. The operation of both concepts is similar. In the mixing mode, the recirculation pump withdraws liquid from the tank and sprays it into the tank liquid, ullage, and exposed tank surfaces. When energy is required. a small portion of the recirculated liquid is passed sequentially through the J-T expansion valve, the heat exchanger, and is vented overboard. The vented vapor cools the circulated bulk fluid, thereby removing thermal energy and reducing tank pressure. The pump operates alone, cycling on and off, to destratify the tank liquid and ullage until the liquid vapor pressure reaches the lower set point. At that point. the J-T valve begins to cycle on and off with the pump. Thus, for short duration missions, only the mixer may operate, thus minimizing or even eliminating, boil-off losses.

Flachbart, Robin H.↗
NASA NTRS2001

Zero Gravity Cryogenic Vent System Concepts for Upper Stages

The capability to vent in zero gravity without resettling is a technology need that involves practically all uses of sub-critical cryogenics in space, and would extend cryogenic orbital transfer vehicle capabilities. However, the lack of definition regarding liquid/ullage orientation coupled with the somewhat random nature of the thermal stratification and resulting pressure rise rates, lead to significant technical challenges. Typically a zero gravity vent concept, termed a thermodynamic vent system (TVS), consists of a tank mixer to destratify the propellant, combined with a Joule-Thomson (J-T) valve to extract thermal energy from the propellant. Marshall Space Flight Center's (MSFC's) Multipurpose Hydrogen Test Bed (MHTB) was used to test both spray-bar and axial jet TVS concepts. The axial jet system consists of a recirculation pump heat exchanger unit. The spray-bar system consists of a recirculation pump, a parallel flow concentric tube heat exchanger, and a spray-bar positioned close to the longitudinal axis of the tank. The operation of both concepts is similar. In the mixing mode, the recirculation pump withdraws liquid from the tank and sprays it into the tank liquid, ullage, and exposed tank surfaces. When energy extraction is required, a small portion of the recirculated liquid is passed sequentially through the J-T expansion valve, the heat exchanger, and is vented overboard. The vented vapor cools the circulated bulk fluid, thereby removing thermal energy and reducing tank pressure. The pump operates alone, cycling on and off, to destratify the tank liquid and ullage until the liquid vapor pressure reaches the lower set point. At that point, the J-T valve begins to cycle on and off with the pump. Thus, for short duration missions, only the mixer may operate, thus minimizing or even eliminating boil-off losses.

Flachbart, Robin H.↗
NASA NTRS1974

Radio frequency studies in the NASA Lewis Bumpy Torus

The fluctuations in potential of the plasma in the NASA Lewis Bumpy Torus are observed using capacitive probes over frequencies from 1 kHz to 25 MHz and a wide range of operating conditions. The spectra are found to differ greatly above and below a background gas pressure of .000034 torr deuterium. Above this pressure, the spectrum is dominated by the ion spoke frequency and a spectral index may be defined. Below this pressure, the spectrum below 200 kHz is lower in amplitude by a factor of ten and no spectral index can be defined. At these lower pressures, fluctuations appearing to be ion spokes are observed, but have a dependence of frequency on operating conditions which is previously unreported.

Gerdin, G. A.↗
NASA NTRS1977

Surfactant-assisted coal liquefaction

Improved process of coal liquefaction utilizing nonaqueous surfactant has increased oil yield from 50 to about 80%. Asphaltene molecule formation of colloid particles is prevented by surfactant. Separated molecules present more surface area for hydrogenation reaction. Lower requirements for temperature, pressure, and hydrogen lead to reduction in capital and operation costs.

Hsu, G. C.↗
NASA NTRS1976

Altitude performance of a low-noise-technology fan in a turbofan engine with and without a sound suppressing nacelle

Test variables were inlet Reynolds number index (0.2 to 0.5), flight Mach number (0.2 to 0.8), and flow distortion (tip radial and combined circumferential - tip radial patterns). Results are limited to fan bypass and overall engine performance. There were no discernible effects of Reynolds number on fan performance. Increasing flight Mach number shifted the fan operating line such that pressure ratio decreased and airflow increased. Inlet flow distortion lowered stall margin. For a Reynolds number index of 0.2 and flight Mach number of 0.54, the sound suppressing nacelle lowered fan efficiency three points and increased specific fuel consumption about 10 percent.

Biesiadny, T. J.↗
NASA NTRS2002

Design and Study of a LOX/GH2 Throttleable Swirl Injector for Rocket Applications

A LOX/GH2 swirl injector was designed for a 10:1 propellant throttling range. To accomplish this, a dual LOX (liquid oxygen) manifold was used feeding a single common vortex chamber of the swirl element. Hot-fire experiments were conducting for rocket chamber pressures from 80 to 800 psia at a mixture ratio of nominally 6.0 using steady flow, single-point-per-firing cases as well as dynamic throttling conditions. Low frequency (mean) and high frequency (fluctuating) pressure transducer data, flow meter measurements, and Raman spectroscopy images for mixing information were obtained. The injector design, experimental setup, low frequency pressure data, and injector performance analysis will be presented. C efficiency was very high (approximately 100%) at the middle of the throttle-able range with somewhat lower performance at the high and low ends. From the analysis of discreet steady state operating conditions, injector pressure drop was slightly higher than predicted with an inviscid analysis, but otherwise agreed well across the design throttling range. Analysis of the dynamic throttling data indicates that the injector may experience transient conditions that effect pressure drop and performance when compared to steady state results.

Greene, Christopher↗
NASA NTRS2001

Mars Flyer Rocket Propulsion Risk Assessment: ARC Testing

This report describes the investigation of a 10-N, bipropellant thruster, operating at -40 C, with monomethy1hydrazine (MMH) and 25% nitric oxide in nitrogen tetroxide (MON-25). The thruster testing was conducted as part of a risk reduction activity for the Mars Flyer, a proposed mission to fly a miniature airplane in the Martian atmosphere. Testing was conducted using an existing thruster, designed for MMH and MON-3 propellants. MON-25 oxidizer was successfully manufactured from MON-3 by the addition of nitric oxide. The thruster was operated successfully over a range of propellant temperatures (-40 to 21 C and feed pressures (6.9 to 20.7 kPa). The thruster hardware was always equal or lower than the propellant temperature. Most tests were 30- and 60-second durations, with 600- and 1200-second duration and pulse testing also conducted. When operating at -40 C, the mixture ratio of the thruster shifted from the nominal value of 1.65 to about 1.85, probably caused by an increase in MMH viscosity, with a corresponding reduction in MMH flowrate. Specific impulse at - 40 C (at nominal feed pressures) was 267 sec, while performance was 277 sec at 21 C. This difference in performance was due, in part, to the mixture ratio shift.

Source record↗
NASA NTRS1974

Radio frequency studies in the NASA Lewis Bumay Torus

The fluctuations in potential of the plasma in the NASA Lewis Bumpy Torus were observed using capacitive probes over frequencies from 1 kHz to 25 MHz and a wide range of operating conditions. The spectra were found to differ greatly above and below a background gas pressure of 3.0.000034 torr deuterium. Above this pressure the spectrum was dominated by the ion spoke frequency and a spectral index was defined. Below this pressure the spectrum below 200 kHz was lower in lower in amplitude by a factor of ten and no spectral index could be defined. At these lower pressures, fluctuations that appeared to be ion spokes were observed, but had a dependence of frequency on operating conditions which was previously unreported.

Gerdin, G. A.↗
NASA NTRS1972

New circumferential seal design concept using self-acting lift geometries

Seal operating temperatures, leakage (pressurizing gas flow), torque, and wear of a conventional circumferential shaft seal were measured and compared to those of a conventional seal modified to have self-acting lift geometries. Both seal types had a 2.625-in diameter bore and were operated at a sliding velocity of 150 ft/sec with differential pressures ranging from 0 to 100 psi. Results of this investigation show that the self-acting seal operated at lower bulk carbon temperatures with half the torque and approximately one-tenth the wear of the conventional seal. Seal leakage of the self-acting seal was of order of 0.04 scfm for pressures above 60 psi which is well within the accepted range for gas turbine engine applications.

Hady, W. F.↗
NASA NTRS1975

Bosch CO2 Reduction System Development

Refinements in the design of a Bosch CO2 reduction unit for spacecraft O2 production are described. Sealing of the vacuum insulation jacket was simplified so that high vacuum and high insulation performance are easily maintained. The device includes a relatively simple concentric shell recuperative heat exchanger which operates at approximately 95% temperature effectiveness and helps lower power consumption. The influence of reactor temperature, pressure, and recycle gas composition on power consumption was investigated. In general, precise control is not required since power consumption is not very sensitive to moderate variations of these parameters near their optimum values. There are two process rate control modes which match flow rate to process demand. Catalyst conditioning, support, and packing pattern developments assure consistent starts, reduced energy consumption, and extended cartridge life. Operation levels for four or five men were maintained with overall power input values of 50 to 60 watts per man.

Holmes, R. F.↗
NASA NTRSDate not supplied

NASA GRC Stirling Research Lab

The efficiency of conversion from thermal to electrical can be increased significantly by using the Stirling thermodynamic cycle •Alternate heating and cooling on volume of gas creates a pressure wave that drives a piston attached to an alternator •Heat can be supplied by any source –radioisotope •Cooling must also be provided for the waste heat portion of the cycle –radiant heat transfer to space •Up to 40% thermal-to-electric efficiency •Dynamic : has moving parts Cycle operation: •A displacer shuttles gas between the hot and cold ends to raise and lower the gas pressure •With displacer at the top, gas is pushed towards cold end, lowering the pressure •With displacer at the bottom, gas is pushed towards the hot-end, raising the pressure •The piston’s mechanical energy can then be utilized as desired –for electrical power it is coupled to an alternator •The motions of the piston and displacer can be controlled by mechanical linkages (kinematic) or by the working gas pressure (free piston)

Stirling Research Lab↗
NASA NTRS1995

Relative performance comparison between baseline labyrinth and dual-brush compressor discharge seals in a T-700 engine test

In separate series of YT-700 engine tests, direct comparisons were made between the forward-facing labyrinth and dual brush compressor discharge seals. Compressor speeds to 43 000 rpm, surface speeds to 160 m/s (530 ft/s), pressures to 1 MPa (145 psi), and temperatures to 680 K (765 F) characterized these tests. The wear estimate for 46 hr of engine operations was less than 0.025 mm (0.001 in.) of the Haynes 25 alloy bristles running against a chromium-carbide-coated rub runner. The pressure drops were higher for the dual-brush seal than for the forward-facing labyrinth seal and leakage was lower-with the labyrinth seal leakage being 2-1/2 times greater-implying better seal characteristics, better secondary airflow distribution, and better engine performance (3 percent at high pressure to 5 percent at lower pressure) for the brush seal. (However, as brush seals wear down (after 500 to 1000 hr of engine operation), their leakage rates will increase.) Modification of the secondary flow path requires that changes in cooling air and engine dynamics be accounted for.

Hendricks, Robert C.↗
NASA NTRS1990

Liquid-Flow Controller Responds To Pressure

Mechanism controls flow of liquid in fuel-spraying head in combustion chamber responds nonlinearly to pressure of liquid. Shell of spraybar expands or contracts laterally as its internal pressure rises or falls, forcing collar down or up on entry tube. Area of window formed by slots in collar and entry tube thus increases or decreases. Drop in pressure through variable-area orifice increases much more with flow through orifice than does corresponding drop in pressure with flow through fixed-area orifice. In practical terms, lower pump pressure needed with variable orifice for given flow of liquid. Principle of operation applicable to spraying heads for other fluids.

Cox, George B., Jr.↗
NASA NTRS2004

Air Separation Using Hollow Fiber Membranes

The NASA Glenn Research Center in partnership with the Ohio Aerospace Institute provides internship programs for high school and college students in the areas of science, engineering, professional administrative, and other technical areas. During the summer of 2004, I worked with Dr. Clarence T. Chang at NASA Glenn Research Center s combustion branch on air separation using hollow fiber membrane technology. . In light of the accident of Trans World Airline s flight 800, FAA has mandated that a suitable solution be created to prevent the ignition of fuel tanks in aircrafts. In order for any type of fuel to ignite, three important things are needed: fuel vapor, oxygen, and an energy source. Two different ways to make fuel tanks less likely to ignite are reformulating the fuel to obtain a lower vapor pressure for the fuel and or using an On Board Inert Gas Generating System (OBIGGS) to inert the Central Wing Tank. goal is to accomplish the mission, which means that the Air Separation Module (ASM) tends to be bulky and heavy. The primary goal for commercial aviation companies is to transport as much as they can with the least amount of cost and fuel per person, therefore the ASM must be compact and light as possible. The plan is to take bleed air from the aircraft s engines to pass air through a filter first to remove particulates and then pass the air through the ASM containing hollow fiber membranes. In the lab, there will be a heating element provided to simulate the temperature of the bleed air that will be entering the ASM and analysis of the separated air will be analyzed by a Gas Chromatograph/Mass Spectrometer (GC/MS). The GUMS will separate the different compounds in the exit streams of the ASM and provide information on the performance of hollow fiber membranes. Hopefully I can develop ways to improve efficiency of the ASM. different types of jet fuel were analyzed and data was well represented on SAE Paper 982485. Data consisted of the concentrations of over 300 different hydrocarbons commonly found in JP- 8, Jet A, and JP-5 fuels. I researched the major hydrocarbons that has a concentration of greater than 50 parts per million and found the vapor pressure data coefficients for a specific temperature range. The coefficients were applied to Antoine s Equation and Riedel's Equation to calculate the vapor pressures for that specific hydrocarbon in the specific temperature range. With the vapor pressure data scientists can formulate a fuel composition that has a lower vapor pressure profile, therefore making jet fuels less flammable. work, learn how to operate and examine the data from Gas Chromatograph and Mass Spectrometer, and develop new ways in applying hollow fiber membrane technology to other areas of environmental engineering. The United States military currently uses air separation technology and their primary The other side of making air travel safer is to reformulate the fuel. Analyses of three My goal this summer is to learn about hollow fiber membrane technologies and how they

Huang, Stephen E.↗
NASA NTRSDate not supplied

Isolator Shock Train Response to Dual-Mode Scramjet Throttling-Like Forcing

Typical dual-mode scramjet designs employ an isolator component situated between the inlet and combustor. The isolator fluidically buffers the inlet from the combustor via the formation of a shock train, an interconnected series of shock-boundary layer interactions. The isolator is required during ramjet-engine operation and at the lower edges of the scramjet operational envelope. In an operational engine, transient behavior imposes fluidic dynamics due to attitude adjustments, combustor throttling, aberrant resonances within the combustor, etc. To accommodate these transients, the shock train adjusts on both temporal and spatial scales. Sufficiently large downstream pressure increases in the combustor play a critical role during unstart, whereby strong compression waves propagate upstream in the isolator to ultimately force the shock train out the inlet, if it cannot stabilize to the pressure increase. This critically reduces the engine mass flow rate, potentially causing a catastrophic reduction in thrust and loss of the vehicle. A nearly instantaneous unstart can, in principle, be predicted by a ratio of the normal shock pressure jump in an inviscid isolator. However, lower-magnitude perturbations, below this bound, also induce unstarts. Understanding the transient behavior inherent in unsteady isolator operation is critical to reducing safety margin in isolator length and refining engine control algorithms to improve engine performance. The Isolator Dynamics Research Lab (IDRL) is a cold-flow, direct-connect isolator facility ideal for assessing the fundamental fluid dynamics of shock trains. The internal flow of a scramjet isolator is modeled using a 2D, symmetric Mach 2.5 nozzle followed by a 695 mm long, 25.4x50.8 mm rectangular isolator test section. A blockage cone on a high-speed ball screw actuator downstream of the isolator is pulsed to simulate the throttling behavior in an operational combustor. Wall flush high-speed static pressure transducers detect the streamwise shock train within the isolator. Time delays between the onset of the throttling and the response motion of the shock train are analyzed to assess the controlling scales and parameters. From this analysis, the response time of the isolator shock train system is found to depend primarily on the isolator back pressure time-rate-of-change but quickly saturates to a maximum propagation speed along the isolator. These results inform dual-mode scramjet engine designers of the critical parameters and limits of an unstart resistant engine.

scramjet↗
NASA NTRS1998

CFD Modelling of Bore Erosion in Two-Stage Light Gas Guns

A well-validated quasi-one-dimensional computational fluid dynamics (CFD) code for the analysis of the internal ballistics of two-stage light gas guns is modified to explicitly calculate the ablation of steel from the gun bore and the incorporation of the ablated wall material into the hydrogen working cas. The modified code is used to model 45 shots made with the NASA Ames 0.5 inch light gas gun over an extremely wide variety of gun operating conditions. Good agreement is found between the experimental and theoretical piston velocities (maximum errors of +/-2% to +/-6%) and maximum powder pressures (maximum errors of +/-10% with good igniters). Overall, the agreement between the experimental and numerically calculated gun erosion values (within a factor of 2) was judged to be reasonably good, considering the complexity of the processes modelled. Experimental muzzle velocities agree very well (maximum errors of 0.5-0.7 km/sec) with theoretical muzzle velocities calculated with loading of the hydrogen gas with the ablated barrel wall material. Comparison of results for pump tube volumes of 100%, 60% and 40% of an initial benchmark value show that, at the higher muzzle velocities, operation at 40% pump tube volume produces much lower hydrogen loading and gun erosion and substantially lower maximum pressures in the gun. Large muzzle velocity gains (2.4-5.4 km/sec) are predicted upon driving the gun harder (that is, upon using, higher powder loads and/or lower hydrogen fill pressures) when hydrogen loading is neglected; much smaller muzzle velocity gains (1.1-2.2 km/sec) are predicted when hydrogen loading is taken into account. These smaller predicted velocity gains agree well with those achieved in practice. CFD snapshots of the hydrogen mass fraction, density and pressure of the in-bore medium are presented for a very erosive shot.

Bogdanoff, D. W.↗
NASA NTRS1988

Designing A Transonic Nozzle For Efficient Cooling

Design for high-pressure transonic-flow nozzle increases effectiveness of coolant flowing in passages in wall nozzle. Revised curvatures of nozzle wall provide shortened transonic region and enable selection of approach- and discharge-wall angles for maximum cooling. Design enables wall to operate at lower temperature, reducing thermal fatigue and increasing life expectancy of wall. Also enables coolant to flow through wall channels with lower pressure drop and lower pumping pressure.

Wagner, William R.↗
NASA NTRS2012

Dual-Compartment Inflatable Suitlock

A paper discusses a dual-compartment inflatable suitlock (DCIS) for Extra - vehicular Activity (EVA) that will allow for dust control, suit maintenance, and efficient EVA egress/ingress. The expandable (inflatable technologies) aspect of the design will allow the unit to stow in a compact package for transport. The DCIS consists of three hard, in line bulkheads, separating two cylindrical membrane-walled compartments. The inner bulkhead can be fitted with a variety of hatch types, docking flanges, and mating hardware, such as the common berthing mechanism (CBM), for the purpose of mating with vehicles, habitats, and other pressurized modules. The inner bulkhead and center bulkhead function as the end walls of the inner compartment, which, during operations, would stay pressurized, either matching the pressure of the habitat or acting as a lower-pressure transitional volume. The suited crewmember can quickly don a suit, and egress the suitlock without waiting for the compartment to depressurize. The outer compartment can be pressurized infrequently, when a long dwell time is expected prior to the next EVA, or during off-nominal suit maintenance tasks, allowing shirtsleeve inspections and maintenance of the space suits. The outer bulkhead has a pressure-assisted hatch door that stays open and stowed routinely, but can be closed for suit maintenance and pressurization as needed.

Howe, Scott↗