Search NASA⌕ Search

SEARCH · Search NASA

Results for “barrier layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Comparison of time-resolved photoluminescence and deep-level transient spectroscopy defect evaluations in an InAs nBn detector subjected to in situ and ex situ 63 MeV proton irradiation

Deep-level transient spectroscopy and temperature-dependent time-resolved photoluminescence experiments are performed on identical InAs nBn photodetector structures as a function of in situ and ex situ 63 MeV proton irradiation to assess their generation and recombination dynamics. Pre-irradiation, the n-type InAs absorbing region, exhibits a steadily increasing minority carrier lifetime with increasing temperature, providing evidence that excited minority carriers may be recombining via shallow defect levels. From deep-level transient spectroscopy, two features are found between 10 and 275 K: a low temperature broad “shoulder,” which suggests emission from multiple shallow electron defect levels with energies <29 meV and a high temperature minimum occurring at ∼230 K with an activation energy of 539 meV, which suggests a defect in the barrier layer in the device. Two similar nBn detectors are then subjected to 63 MeV proton irradiation in step doses and measured between steps. One experiment is performed in situ with an nBn held at ∼10 K during dosing, and the other experiment is performed ex situ with a similar nBn held at room temperature for dosing. The ex situ dosing results in an evaluation of the defect introduction rate that is three to four times lower than in situ due to partial annealing of the proton-induced displacement damage at room temperature. The results of these two experiments are then compared with the dose-dependent recombination rate analysis, resulting in an estimated recombination defect cross section of 1.6 × 10 −13 cm 2 for the shallow shoulder defect.

Carrasco, Rigo A. [Air Force Research Laboratory (↗

Giant Polarization in Nanodielectrics

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of p-doping on the intensity noise of epitaxial quantum dot lasers on silicon

This work experimentally investigates the impact of p-doping on the relative intensity noise (RIN) properties and subsequently on the modulation properties of semiconductor quantum dot (QD) lasers epitaxially grown on silicon. Owing to the low threading dislocation density and the p-modulation doped GaAs barrier layer in the active region, the RIN level is found very stable with temperature with a minimum value of − <#comment/> 150 d B / H z . The dynamical features extracted from the RIN spectra show that p-doping between zero and 20 holes/dot strongly modifies the modulation properties and gain nonlinearities through increased internal losses in the active region and thereby hinders the maximum achievable bandwidth. Overall, this Letter is important for designing future high-speed and low-noise QD devices integrated in future photonic integrated circuits.

Duan, Jianan (ORCID:0000000177104287)↗

Mechanical Behavior of Hybrids with Hyper-Connected Molecular Networks

Our research is focused on fundamental studies related to the molecular design, synthesis, characterization and modeling of molecular-reinforced hybrid glass films for superior mechanical and fracture properties. Molecular-reinforced hybrid glass films exhibit unique electro-optical properties while maintaining excellent thermal stability. They have important technological application for emerging nanoscience and energy technologies including anti-reflective and ultra-barrier layers in photovoltaics, display technologies, as well as quantum technologies. However, they are often inherently brittle in nature, do not adhere well to adjacent substrates, and exhibit poor mechanical properties. Furthermore, a robust understanding of the underlying mechanisms of deformation, fracture and fatigue has been lacking particularly given their mechanically fragile nature. The related lack of structure-property relationships between molecular structure, mechanical properties and processing represents a fundamental challenge to their integration into device technologies, compromises their thermomechanical reliability and has thwarted efforts to improve mechanical and, particularly, fracture properties.

36 MATERIALS SCIENCE↗

High Performance SOFCs with a Superior Stability for Reliable and Durable Power Systems

Next generation of fuel cells, electrolyzers, and batteries requires higher power, faster kinetics, and larger energy density, which necessitate the use of compositionally complex oxides to achieve multifunctionalities and activity. These compositionally complex oxides may change their phases and structures during an electrochemical process – a so-called “electrochemically driven phase transformation”. The origin for such a phase change has remained obscure. More importantly, there is a need to develop high performance solid oxide fuel cells with an enhanced stability. In this work, the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) cathode surface is modified by infiltration of Pr 6 O 11 and the power density at 0.8V and 750 °C is improved by 21%. In addition, by replacing the traditional barrier layer Gd 0.2 Ce 0.8 O 1.9 with mixed conducting Pr 0.1 Gd 0.1 Ce 0.8 O 1.9 , the power density increases by 38%. The different mechanism of promotions was investigated by electrochemical impedance spectroscopy. The ohmic resistance is dramatically reduced by applying the PGCO interlayer, and the distribution of relaxation time was used to analyze the mechanism for which the polarization resistance was decreased attributing to the mixed conduction nature in PrO x . An increase of power density at 0.8 V of 0.358 W/cm 2 (71%) is achieved with the implementation of both surface modification and buffer layer engineering. An experimental study and a theoretical analysis were then carried out on phase evolution in praseodymium nickelates. Nickelate-based electrodes show up to 60× greater phase transformation during operation when compared to thermally annealed ones. Theoretical analysis suggests that the presence of a reduced oxygen partial pressure at the interface between the oxygen electrode and the electrolyte is the origin for the phase change in an oxygen electrode. Guided by the theory, an addition of the electronic conduction in the interface layer leads to the significant suppression of phase change, while improving cell performance and performance stability. When an oxygen electrode is under polarization, the oxygen partial pressure at the interface between the oxygen electrode and the electrolyte is lower than that of incoming oxidant. Under a high polarization, the environment at the aforementioned interface may lead to phase transformation of the oxygen electrode. The local oxygen partial pressure is determined by the transport properties at the interfaces. An addition of the electronic conduction in the interface layer, for instance using (Pr,Gd)-doped ceria to replace Gd-doped ceria, results in improved cell performance and performance stability, while the phase transformation is significantly suppressed. This work provides a fundamental understanding of the origin for phase transformation in oxygen electrodes during operation and use this knowledge to develop a high-performance electrode that exhibits improved performance stability.

30 DIRECT ENERGY CONVERSION↗

Cation Migration and LSCF/SDC Decomposition Related to Long-Term Operation Mode as Revealed by Electron Microscopy

This study utilized energy dispersive spectroscopy (EDS) in a scanning electron microscope (SEM) and a scanning transmission electron microscope (STEM) in order to track cation migration and related particle decomposition for air electrode components of solid oxide cells. The influence of a Sm-doped ceria (SDC) barrier layers was assessed for three operation modes (fuel cell, electrolysis, reversible) over long time periods (1000-1500 hours). Composition profiles across air electrode/electrolyte interfaces indicated negligible accumulation of La/Sr cations to the yttria-stabilized zirconia (YSZ) electrolyte during operation. Instead, air electrode particles composed of SDC and/or La-Sr-Co-Fe-oxides (LSCF) exhibited decomposition by Sr evaporation and Sm migration to LSCF particle edges.

Picard, Yoosuf↗

Micro-Mechanically Guided High-Throughput Alloy Design Exploration Towards Metastability-Induced H Embrittlement Resistance

We develop a high-throughput approach for studying H embrittlement (HE)-resistance in alloys, which is based on combinatorial compositional screening of metastability effects by in situ scanning electron microscopy H-analyses. The project objective included: (i) technique development of high-throughput screening (HTS) for HE-resistance, (ii) discovery of new metallic materials with superior HE-resistance, (iii) Multiscale verification of HE-resistance of the new alloys and H-barrier layers, from atomic scale to an engineering scale. The investigation focused on a model system that enables exploration of different metastable states in Fe-based complex-concentrated alloys. Composition spread islands with hundreds of varying compositions are fabricated on a single substrate using a combinatorial co-sputtering technique. To screen these alloys, we developed and employed a home-built SEM-based integrated analysis system capable of characterizing H-permeability, H-trapping, H-influence on mechanical properties, and other material properties, as well as atomistic to continuum simulations to study the underlying physics.

08 HYDROGEN↗

Curable polysiloxane compositions and slippery materials and coatings and articles made therefrom

The present teachings generally provide curable polysiloxane compositions including a base resin including a surface active polymer. Articles of manufacture including the curable polysiloxane compositions and slippery coatings and materials also are provided. The compositions may be used to provide slippery, lubricious, or repellent materials and coatings and may provide anti-fouling function. The compositions can provide anti-fouling or foul-release function on open surfaces, internal surfaces, membranes; to provide pinning free or low contact angle hysteresis surfaces; to provide homogeneous interface to suppress nucleation; to provide a barrier layer such as anti-corrosion; to provide anti-stain, anti-smudge, anti-fingerprint, anti-soil function.

Kim, Philseok↗

Solid-state batteries and the critical role of interfaces

The Grand Challenge for the next generation of energy storage technologies is no longer the identification of electroactive cathode or anode materials thanks to extensive worldwide synthesis efforts along with theory and modeling like the Materials Project.1 Instead, the critical challenges revolve around assembling materials in the right architecture to achieve maximum performance and cell life at reasonable temperatures and pressures. Nowhere is this more critical than on the next generation of energy storage technologies revolving around all solid-state batteries. These batteries are the ultimate challenge for materials science requiring new ways to assemble multiple dissimilar materials such that: (1) interfaces are optimized to facilitate ion motion across the different compounds while (2) maintaining chemical stability and (3) simultaneously preserving the crystal structures of each phase during (4) large volume changes due to shuttling of lithium, at (5) room temperature and under (6) atmospheric pressure. To address these requirements will require insights and expertise from research fields outside the traditional lithium-ion battery community such as solid oxide fuel cells, synthesis science, barrier layers, interface formers, sintering, and mechanical properties.

25 ENERGY STORAGE↗

Sr and Co Vapor-Phase Transport from LSCF Cathodes

A series of tests were performed to differentiate between surface diffusion and vapor-phase diffusion of chemical species from LSCF cathode material at typical sintering temperatures (up to 1100°C) in SOFC production. A GDC source substrate was printed with LSCF and separated by an air gap from a YSZ target substrate. Various geometries with long surface paths were employed to reduce the possibility of surface transport. Sr and Co were detected on the target substrates via energy dispersive spectroscopy (EDS) and x-ray photoelectron spectroscopy (XPS), including spatially resolved XPS. These results support a vapor-phase transport mechanism for Sr and Co. Sintering conditions and barrier layer requirements may need to be revisited to prevent the formation of undesired strontium zirconate at cathode/electrolyte interface due to vapor-phase transport.

vapor phase transport, SOFC cathode, Sr transport↗

Giant polarization in nanodielectrics

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Progress in High-Dielectric Constant Materials

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Curable polysiloxane compositions and slippery materials and coatings and articles made therefrom

The present teachings generally provide curable polysiloxane compositions including a base resin including a surface active polymer. Articles of manufacture including the curable polysiloxane compositions and slippery coatings and materials also are provided. The compositions may be used to provide slippery, lubricious, or repellent materials and coatings and may provide anti-fouling function. The compositions can provide anti-fouling or foul-release function on open surfaces, internal surfaces, membranes; to provide pinning free or low contact angle hysteresis surfaces; to provide homogeneous interface to suppress nucleation; to provide a barrier layer such as anti-corrosion; to provide anti-stain, anti-smudge, anti-fingerprint, anti-soil function.

Kim, Philseok↗

Solar cells formed via aluminum electroplating

Electroplating of aluminum may be utilized to form electrodes for solar cells. In contrast to expensive silver electrodes, aluminum allows for reduced cell cost and addresses the problem of material scarcity. In contrast to copper electrodes which typically require barrier layers, aluminum allows for simplified cell structures and fabrication steps. In the solar cells, point contacts may be utilized in the backside electrodes for increased efficiency. Solar cells formed in accordance with the present disclosure enable large-scale and cost-effective deployment of solar photovoltaic systems.

Tao, Meng↗

Heat transfer module

A heat transfer module can include an envelope sealed to define an internal volume that contains a working fluid and a wick disposed on an internal surface of the envelope. The wick and envelope each has a first portion extending through an evaporator region and a second portion extending through adiabatic and condenser regions. The first portion of the wick is a metal hydride. The first portion of the envelope includes a metal liner surrounding the first portion of the wick, a first diffusion barrier layer disposed between the first portion of the wick and the metal liner, and a ceramic matrix composite cladding surrounding the metal liner. The second portions of the wick and envelope each includes a refractory metal and/or stainless steel.

Stauff, Nicolas E.↗

Condensation-based redox flow battery rebalancing

In a redox flow battery (RFB), the base solvent of the electrolytes tends to migrate across the barrier layer from one electrode toward the other. This can result in a volume and concentration imbalance between the electrolytes that is detrimental to battery efficiency and capacity. Compatible electrolytes can be mixed to rebalance the system, but for incompatible electrolytes mixing is not a viable option. To this end, the RFB herein includes a separator that recovers base solvent from the vapor phase of one of the electrolytes and returns the recovered base solvent to the other electrolyte to thereby reverse the imbalance.

Saraidaridis, James D.↗

Barrier coatings

A secondary electron emissive layer resistant to infiltration and fouling. A barrier layer is formed by atomic layer deposition. The barrier layer may be an emissive layer and/or an interlayer. The barrier layer may form an interlayer that is a part of an electron amplifier positioned between an emissive layer and a resistive layer. The barrier layer is resistive to fluorine migration from either the emissive layer or the resistive layer.

Source record↗

Photovoltaic structures having multiple absorber layers separated by a diffusion barrier

Photovoltaic structures having multiple absorber layers separated by a diffusion barrier are provided. In one aspect, a method of forming an absorber on a substrate includes: depositing a first layer of light absorbing material on the substrate; depositing a diffusion barrier; depositing a second layer of light absorbing material on the diffusion barrier, wherein the first layer of light absorbing material has a different band gap from the second layer of light absorbing material; and annealing the absorber, wherein the diffusion barrier prevents diffusion of elements between the first layer of light absorbing material and the second layer of light absorbing material during the annealing. A solar cell and method for formation thereof are also provided.

14 SOLAR ENERGY↗