Search NASA⌕ Search

SEARCH · Search NASA

Results for “batched factorization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

High Sodium Simulant Testing To Support SB8 Sludge Preparation

Scoping studies were completed for high sodium simulant SRAT/SME cycles to determine any impact to CPC processing. Two SRAT/SME cycles were performed with simulant having sodium supernate concentration of 1.9M at 130% and 100% of the Koopman Minimum Acid requirement. Both of these failed to meet DWPF processing objectives related to nitrite destruction and hydrogen generation. Another set of SRAT/SME cycles were performed with simulant having a sodium supernate concentration of 1.6M at 130%, 125%, 110%, and 100% of the Koopman Minimum Acid requirement. Only the run at 110% met DWPF processing objectives. Neither simulant had a stoichiometric factor window of 30% between nitrite destruction and excessive hydrogen generation. Based on the 2M-110 results it was anticipated that the 2.5M stoichiometric window for processing would likely be smaller than from 110-130%, since it appeared that it would be necessary to increase the KMA factor by at least 10% above the minimum calculated requirement to achieve nitrite destruction due to the high oxalate content. The 2.5M-130 run exceeded the DWPF hydrogen limits in both the SRAT and SME cycle. Therefore, testing of this wash endpoint was halted. This wash endpoint with this minimum acid requirement and mercury-noble metal concentration profile appears to be something DWPF should not process due to an overly narrow window of stoichiometry. The 2M case was potentially processable in DWPF, but modifications would likely be needed in DWPF such as occasionally accepting SRAT batches with undestroyed nitrite for further acid addition and reprocessing, running near the bottom of the as yet ill-defined window of allowable stoichiometric factors, potentially extending the SRAT cycle to burn off unreacted formic acid before transferring to the SME cycle, and eliminating formic acid additions in the frit slurry.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Production of monodisperse cerium oxide microspheres with diameters near 100 µm by internal-gelation sol–gel methods

Cerium dioxide microspheres with uniform diameters between 65 – 211 µm were fabricated using internal gelation sol-gel methods. Although uniform microspheres are produced for nuclear fuel applications with diameters above 300 µm, sol-gel microspheres with diameters of 50 - 200 µm have historically been made by emulsion techniques and had poor size uniformity [1, 2]. An internal gelation, sol-gel apparatus was designed and constructed to accommodate the production of small, uniform microspheres whereby cerium-containing solutions were dispersed into flowing silicone oil and heated in a gelation column to initiate solidification [3, 4]. Problems with premature feed gelation and microsphere coalescence were overcome by equipment modifications unique among known internal gelation setups. Microspheres were fabricated and sized in batches as a function of dispersing needle diameter and silicone oil flow rate in the two-fluid nozzle in order to determine the range of sizes possible and corresponding degree of monodispersity. Initial experiments with poor size uniformity were linked to microsphere coalescence in the gelation column prior to solidification as well as excessive flow rates for the cerium feed solution. Average diameter standard deviations as low as 2.23% were observed after optimization of flow rates and minimization of coalescence reactions.

cerium oxide↗

Microbe-Encapsulated Silica Gel Biosorbents for Selective Extraction of Scandium from Coal Byproducts

Establishing an inexpensive and environmentally friendly scandium (Sc) supply is critical for the development of clean energy technologies. However, refining Sc from Sc-bearing sources using current technologies poses economic and environmental challenges due to its low concentration relative to base metals and chemically similar lanthanides. In this work, we developed a biosorption-based flow-through process for extraction of Sc from low-grade feedstocks. A novel biosorbent material was synthesized by encapsulating Arthrobacter nicotianae, a bacterium that selectively adsorbs Sc, within a porous silica matrix. Through the use of several complementary microscopy techniques, we demonstrated a highly porous biosorbent structure with a high cell-loading density and a homogenous cell distribution. Batch adsorption assays revealed selective Sc adsorption over lanthanides and common based metals, with the exception of Fe(III), as evidenced by separation factors greater than 50. The MESG particles were packed into fixed-bed columns to enable adsorption under flow-through conditions, which demonstrated effective Sc extraction at flow rates up to 0.08 cm/s and high stability for reuse; greater than 95% of the adsorption capacity was maintained after 10 consecutive adsorption/desorption cycles. When applied to a lignite coal leachate, whose Fe content was depleted through pH-mediated precipitation, the MESG particles yielded Sc breakthrough at 30 bed volumes, whereas all other metals broke through after only a few bed volumes. Following desorption, an eluate with a 124-fold increase in Sc purity was achieved relative to the lignite leachate with Sc constituting 96.4% of the total REEs. This study established a rapid, facile, and scalable cell immobilization approach that enables the use of microbial biomass for Sc recovery from low-grade sources.

Dong, Ziye↗

A combined experimental and modelling study of granite hydrothermal alteration

Geochemical reactions can induce significant changes of rock reservoir porosity and permeability via mineral dissolution and precipitation processes, affecting the long-term fluid behaviour within various geological systems. Here, the understanding and quantification of these reactions rely on field and experimental studies and on the predictions of reactive transport models. The present study was aimed at assessing the extent to which current geochemical models integrating available mineral dissolution/precipitation rate equations can reproduce the experimental data obtained from 4 to 17-day long hydrothermal alteration experiments of a muscovite-biotite granite and, thus, help provide an accurate description of the evolution of geothermal systems within granitic reservoirs. The experiments were conducted at a constant temperature of 180 °C and over an aqueous fluid pH range of 2 to 8.5, using both mixed-flow and static batch reactors. Modelled major element (K, Al, Si, Ca, and Mg) concentrations were generally in satisfactory agreement with the corresponding measured elemental fluxes – the differences between modelled and experimental values were generally within a factor of 5 – and the predicted identity and mass of formed secondary phases were consistent with the microscopic observations of the reacted solids. However, larger differences between measured and modelled element concentrations were observed when significant amounts of secondary phases formed, notably at pH 2 to 3, and for longer-term batch experiments. Much of this concentration difference stems from the underestimation of the amounts of Al-phases formed at acid to near-neutral pH. Although an idealized rock composition was considered, the observed mismatch between model calculations and experimental data can be attributed to inadequate mineral precipitation reaction rates and a poor description of reactive surface areas in existing geochemical modelling codes. More accurate quantification of precipitation kinetics, including nucleation and growth, and improved descriptions of the temporal change of mineral surface area would enhance the predictive capabilities of reactive transport models and benefit, particularly, the efforts aimed at increasing the sustainability of EGS reservoirs.

58 GEOSCIENCES↗

Efficient multistep arsenate removal onto magnetite modified fly ash

The modification of the fly ash (FA) by magnetite (M) was performed to obtain FAM adsorbent with improved adsorption efficiency for arsenate removal from water. The novel low cost adsorbents are characterized by liquid nitrogen porosimetry (BET), scanning electron microscopy (SEM), X-ray diffraction (XRD), Mössbauer spectroscopy (MB) and Fourier transform infrared (FTIR) spectroscopy. The optimal conditions and key factors influencing the adsorbent synthesis are assessed using the response surface method (RSM). The adsorption experiment was carried out in a batch system by varying the contact time, temperature, pH, and mass of the adsorbent. The adsorption capacity of the FAM adsorbent for As(V), calculated by Langmuir model, was 19.14 mg g−1. The thermodynamic parameters showed spontaneity of adsorption with low endothermic character. The kinetic data followed the pseudo-second-order kinetic model (PSO), and Weber-Morris model indicated intra-particle diffusion as rate limiting step. Alternative to low desorption capability of the FAM was found by five consecutive adsorption/magnetite precipitation processes which gave exhausted layered adsorbent with 65.78 mg g−1 capacity. This research also has shed light on the mechanism of As(V)-ion adsorption, presenting a promising solution for the valorization of a widely abundant industrial waste. © 2018 Elsevier Ltd.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical and Radiological Compatibility Testing of 3D Printed Materials

To dramatically increase the adaptability, performance, and safety of processes in support of the Defense Waste Processing Facility (DWPF), Savannah River National Lab (SRNL) plans to perform chemical and radiological compatibility testing on a wide variety of 3D printed materials of interest. The 3D printing process provides numerous strategic operational benefits such as rapid prototyping of complex designs and geometry specific to the needs of the nuclear waste disposition process, as well as on-demand rapid prototyping and iteration with materials that aren’t as accessible through traditional manufacturing methods. Reaction chemistry in simulated waste batches can be matched closely to its radioactive counterpart, but glass reactor vessels have limitations. Vessel geometry can play a big factor in mixing transport limitations, process chemistry, and degradation reaction kinetics. In addition, additive manufacturing allows for much more detailed vessel design than traditional alternatives. Waste processing techniques in DWPF also encounter extreme chemical environments including high pH, strong acids, abrasive slurries, and significant irradiation. To meet these challenges, a matrix of various polymer, ceramic, and metal additive manufacturing materials have been exposed to a suite of chemical environments of interest as well as radioactive dose (such as gamma radiation from 60 Co) to properly test their durability under these conditions. Mass change has been monitored over a period of up to a week in these conditions, as well as added characterization for surface modification through Scanning Electron Microscopy/Electron Dispersive X-ray analysis (SEM/EDX). Further chemical characterization has been monitored through Fourier-Transform InfraRed Spectroscopy (FTIR), with planned investigation via thermal and tensile strength degradation. While the direct product of this research is identification of material(s) that can withstand specific hazardous environments encountered by the mercury water wash tank in DWPF process simulation experiments, the reference base of materials will be used for many other nuclear processes in the pursuit of rapidly developed, cost-efficient, and highly specific devices for environmental remediation and much more.

Wilson, Nathan W. [Savannah River National Laborat↗

Switching from batch to continuous granulation: A case study of metoprolol succinate ER tablets

Continuous manufacturing (CM) has been used to produce several immediate release drug products. No extended-release (ER) product manufactured employing CM technology has been approved yet. Herein this study investigated the critical aspects of switching from the batch mode of high shear granulation to the continuous operation of twin-screw granulation for extended-release tablets. Metoprolol succinate ER tablets was used as a model ER formulation for this purpose. A central composite design (CCD) was employed to determine the effects of high shear granulator (HSG) parameters, namely impeller speed, granulation time, and binder liquid feeding rate, on the critical granulation characteristics important for product performance. These critical granulation characteristics served as a guide for switching from the batch processing to the continuous operation for achieving the same breaking strength and dissolution for this ER metoprolol tablets. The granulation time was the most critical factor affecting the bulk properties of granules which contributed to tablet dissolution. The higher density and lower compressibility of granules were attained at the longest granulation time of 5.4 min with the fastest liquid feeding rate of 75 g/min. The granules’ density was the primary factor negatively affecting the dissolution of metoprolol tablets. However, the breaking strength of tablets confounded the effect of granules density on metoprolol dissolution. Switching the processing parameters of high shear granulation to twin-screw granulation achieved similar dissolution profiles (F2 greater than 50). The screw speed was not found to affect bulk properties of granules. The root cause of granulation failures in twin-screw granulation, such as premature consolidation, excessive swelling, poor cohesion, inconsistent shearing effects, and formation of deformed agglomerates, were identified. In conclusion, the use of critical granulation characteristics through a performance-based approach of ER tablets facilitated the switching of manufacturing of an ER formulation form batch to continuous operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Universal method for the optimization of HDC coating uniformity on non-planar, non-stationary substrates for inertial confinement fusion targets

The thickness uniformity of chemical vapor deposited (CVD) diamond coatings on non-planar, non-stationary substrates depends on both the intrinsic instantaneous coating thickness distribution (ICTD) of the coating conditions used and, if applicable, on the frequency of substrate reorientation. While important for many CVD diamond applications, the relative impact of the ICTD and substrate reorientation on the coating thickness uniformity has not been studied. In this work, we systematically investigate the effect of these factors for microwave-plasma chemical vapor deposition (MPCVD) of diamond (referred to as high density carbon (HDC) in the inertial confinement fusion (ICF) community) coatings on spherical, rolling substrates. This coating technique is used to fabricate capsules for ICF experiments, which require extreme coating uniformity with <0.3 % thickness variation (so-called Mode 1 or M1) to ensure symmetric compression of imploding targets. To extract the otherwise unobservable reorientation timescale (Δt), Monte Carlo simulations were performed using experimental ICTD data as input. This combined approach confirms scaling relationships between the substrate reorientation timescale as well as coating thickness and coating uniformity, as expected from a 3D random walk. Simulations confirm that M1 is Rayleigh-distributed and scales as (Δt) 1/2 , consistent with the randomization of two angles that determine orientation of a sphere. We also demonstrate that, under the conditions studied, Δt is the dominant factor in determining thickness uniformity while the intrinsic ICTD has minimal impact. Finally, experiments show that Δt can be affected by total batch size under constant agitation conditions due to space constraints that limit the capsule reorientation kinetics. In conclusion, this study highlights the utility of a combined experiment-simulation approach as a general methodology for understanding and improving coating uniformity on non-planar, non-stationary substrates.

Capsule↗

Denitrification versus respiratory ammonification: environmental controls of two competing dissimilatory NO 3 – /NO 2 – reduction pathways in Shewanella loihica strain PV-4

Denitrification and respiratory ammonification are two competing, energy-conserving NO 3 – /NO 2 – reduction pathways that have major biogeochemical consequences for N retention, plant growth and climate. Batch and continuous culture experiments using Shewanella loihica strain PV-4, a bacterium possessing both the denitrification and respiratory ammonification pathways, revealed factors that determine NO 3 – /NO 2 – fate. Denitrification dominated at low carbon-to-nitrogen (C/N) ratios (that is, electron donor-limiting growth conditions), whereas ammonium was the predominant product at high C/N ratios (that is, electron acceptor-limiting growth conditions). pH and temperature also affected NO 3 – /NO 2 – fate, and incubation above pH 7.0 and temperatures of 30 °C favored ammonium formation. Reverse-transcriptase real-time quantitative PCR analyses correlated the phenotypic observations with nir K and nos Z transcript abundances that decreased up to 1600-fold and 27-fold, respectively, under conditions favoring respiratory ammonification. Of the two nrfA genes encoded on the strain PV-4 genome, nrfA 0844 transcription decreased only when the chemostat reactor received medium with the lowest C/N ratio of 1.5, whereas nrfA 0505 transcription occurred at low levels (≤3.4 × 10 –2 transcripts per cell) under all growth conditions. At intermediate C/N ratios, denitrification and respiratory ammonification occurred concomitantly, and both nrfA 0844 (5.5 transcripts per cell) and nir K (0.88 transcripts per cell) were transcribed. Furthermore recent findings suggest that organisms with both the denitrification and respiratory ammonification pathways are not uncommon in soil and sediment ecosystems, and strain PV-4 offers a tractable experimental system to explore regulation of dissimilatory NO 3 – /NO 2 – reduction pathways.

54 ENVIRONMENTAL SCIENCES↗

An Advanced TALSPEAK Concept for Separating Minor Actinides. Part 2. Flowsheet Test with Actinide-spiked Simulant

A solvent extraction system has been developed for separating trivalent actinides from lanthanides. This “Advanced TALSPEAK” system uses 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester to extract the lanthanides into a n-dodecane-based solvent phase, while the actinides are retained in a citrate-buffered aqueous phase by complexation to N-(2-hydroxyethyl)ethylenediamine-N,N',N'-triacetic acid. Batch distribution measurements indicate that the separation of americium from the light lanthanides decreases as the pH decreases. For example, the separation factor between La and Am increases from 2.5 at pH 2.0 to 19.3 at pH 3.0. However, previous investigations indicated that the extraction rates for the heavier lanthanides decrease with increasing pH. So, a balance between these two competing effects is required. An aqueous phase in which the pH was set at 2.6 was chosen for further process development because this offered optimal separation, with a minimum separation factor of ~8.4, based on the separation between La and Am. Centrifugal contactor single-stage efficiencies were measured to characterize the performance of the system under flow conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

spdlayers

Symmetric Positive Definite (SPD) enforcement layers for PyTorch. Regardless of the input, the output of these layers will always be a SPD tensor! The `Cholesky` layer uses a cholesky factorization to enforce SPD, and the `Eigen` layer uses an eigendecomposition to enforce SPD. Both layers take in some tensor of shape `[batch_size, input_shape]` and output a SPD tensor of shape`[batch_size, output_shape, output_shape]`. The relationship between input and output is defined by the following. ```python input_shape = sum([i for i in range(output_shape + 1)]) ``` The layers have no learnable parameters, and merely serve to transform a vector space to a SPD matrix space.

Jekel, CharlesF.↗

Characterization of Li in the Salton Sea Geothermal Field

Abstract The behavior of lithium during geothermal brine and host-rock interactions in the Salton Sea geothermal field is underconstrained. The lithium brine reservoir inventory is between 4 and 18 million metric tons of lithium carbonate equivalent, with an even larger amount present within the reservoir rock mineral phases. Here, we present bulk-rock and brine Li concentration and δ7Li, and in situ Li concentrations of minerals from the California State 2-14 scientific drill core and commercial wells in the Salton Sea geothermal field to identify the mineral hosts of Li and constrain Li behavior during brine-rock interactions. Lithium contents are highest in chlorite (270–580 ppm, ~2,358 m), which encases pyrite, indicating that Li is fixed from the brine into the host rocks during hydrothermal alteration. Lithium abundances in chlorite decrease with depth (70–100 ppm, ~2,882 m), as does whole-rock Li content, whereas whole-rock δ7Li increases (δ7Li = 2.0–4.3‰, ~2,485-m depth; δ7Li = 4.3–7.9‰ from ~2,819 to ~2,882 m). This change in behavior of Li at ~2,500 m suggests temperature dependent partitioning of Li in chlorite; Li becomes more incompatible in chlorite at depths >~2,500 m, corresponding to ~325°C in the reservoir. The brines have δ7Li = 3.7 to 4.7‰ and calculated isotopic fractionation factors between the brine and the host rock agree with a change in Li behavior at ~325°C. Simple closed-system batch modeling does not describe the geothermal system, suggesting open-system behavior of Li within the Salton Sea geothermal field.

Humphreys, J↗

Heat transfer from glass melt to cold cap: Melting rate correlation equation

Increasing the efficiency of all-electric melters is a hot topic not only in the waste glass melting industry, where the melting rate directly influences the life cycle of the cleanup process, but also in the commercial glass industry, where increasingly stringent environmental regulations and rapid development of renewable energy sources ask for transformation of traditional fossil fuel technology. Batch-to-glass conversion in an all-electric melter proceeds in the cold cap—a layer of reacting and melting material floating on molten glass. The heat transfer into the cold cap is controlled by convection and conduction in the thermal boundary layer on the melt side, and by the properties of the foam layer at the cold cap/melt boundary. An overview of factors affecting heat transfer is presented and assessed using data from laboratory and pilot-scale experiments. The heat flux can be improved by (i) decreasing glass melt viscosity, (ii) decreasing the temperature at which the foam starts to collapse at the cold cap bottom, and (iii) increasing melt convection by bubbling gas into the glass melt under the cold cap. Detailed understanding of the conversion process can guide the formulation of feeds that melt easily and quickly.

Hrma, Pavel↗

Scalable nanomanufacturing of chalcogenide inks: a case study on thermoelectric V–VI nanoplates

Solution-processed semiconducting main-group chalcogenides (MMCs) have attracted increasing research interest for next-generation device technologies owing to their unique nanostructures and superior properties. To achieve the full potential of MMCs, the development of highly universal, scalable, and sustainable synthesis and processing methods of chalcogenide particles is thus becoming progressively more important. Here we studied scalable factors for the synthesis of two-dimensional (2D) V–VI chalcogenide nanoplates (M 2 Q 3 : M = Sb, Bi; Q = Se, Te) and systematically investigated their colloidal behaviour and chemical stability. Based on a solvent engineering technique, we demonstrated scale-up syntheses of MMCs up to a 900% increase of batch size compared with conventional hydrazine-based gram-level syntheses, and such a scalable approach is highly applicable to various binary and ternary MMCs. Furthermore, we studied the stability of printable chalcogenide nanoparticle inks with several formulation factors including solvents, additives, and pH values, resulting in inks with high chemical stability (>4 months). As a proof of concept, we applied our solution-processed chalcogenide particles to multiple additive manufacturing methods, confirming the high printability and processability of MMC inks. Furthermore, the ability to combine the top-down designing freedom of additive manufacturing with bottom-up scalable synthesis of chalcogenide particles promises great opportunities for large-scale design and manufacturing of chalcogenide-based functional devices for broad application.

36 MATERIALS SCIENCE↗

DWPF DECON FRIT: SUMP AND SLURRY SOLIDS ANALYSIS

The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. In this report, the physical and chemical characterization results of the slurry solids and sump solids are reported. Crawford et al. (2010) provide the results of the supernate analysis. The results of the sump solids are reported on a mass basis given the samples were essentially dry upon receipt. The results of the slurry solids were converted to a volume basis given approximately 2.4 grams of slurry solids were obtained from the {approx}4 liters of liquid slurry sample. Although there were slight differences in the analytical results between the sump solids and slurry solids the following general summary statements can be made. Slight differences in the results are also captured for specific analysis. (1) Physical characterization - (a) SEM/EDS analysis suggested that the samples were enriched in Li and Si (B and Na not detectable using the current EDS system) which is consistent with two of the four principle oxides of Frit 418 (B{sub 2}O{sub 3}, Na{sub 2}O, Li{sub 2}O and SiO{sub 2}). (b) SEM/EDS analysis also identified impurities which were elementally consistent with stainless steel (i.e., Fe, Ni, Cr contamination). (c) XRD results indicated that the sump solids samples were amorphous which is consistent with XRD results expected for a Frit 418 based sample. (d) For the sump solids, SEM/EDS analysis indicated that the particle size of the sump solids were consistent with that of an as received Frit 418 sample from a current DWPF vendor. (e) For the slurry solids, SEM/EDS analysis indicated that the particle size range of the slurry solids was much broader than compared to the sump solids. More specifically, there were significantly more fines in the slurry solids as compared to the sump solids. (f) PSD results indicated that > 99% of both the sump and slurry solids were less than 350 microns. The PSD results also supported SEM/EDS analysis that there were significantly more fines in the slurry solids as compared to the sump solids. (2) Weight Percent Solids - Based on the measured supernate density and mass of insoluble solids (2.388 grams) filtered from the four liters of liquid slurry samples, the weight percent insoluble solids was estimated to be 0.060 wt%. This level of insoluble solids is higher than the ETP WAC limit of 100 mg/L, or 0.01 wt% which suggests a separation technology of some type would be required. (3) Chemical Analysis - (a) Elemental results from ICP-ES analysis indicated that the sump solids and slurry were very consistent with the nominal composition of Frit 418. There were other elements identified by ICP analysis which were either consistent with the presence of stainless steel (as identified by SEM/EDS analysis) or impurities that have been observed in 'as received' Frit 418 from the vendor. (b) IC anion analysis of the sump solids and slurry solids indicated all of the species were less than detection limits. (c) Radionuclide analysis of the sump solids also indicated that most of the analytes were either at or below the detection limits. (d) Organic analysis of the sump solids and slurry solids indicated all of the species were less than detection limits. It should be noted that the results of this study may not be representative of future decon frit solutions or sump/slurry solids samples. Therefore, future DWPF decisions regarding the possible disposal pathways for either the aqueous or solid portions of the Decon Frit system need to factor in the potential differences. More specifically, introduction of a different frit or changes to other DWPF flowsheet unit operations (e.g., different sludge batch or coupling with other process streams) may impact not only the results but also the conclusions regarding acceptability with respect to the ETF WAC limits or other alternative disposal options.

36 MATERIALS SCIENCE↗

DWPF DECON FRIT SUPERNATE ANALYSIS

The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. This report contains the results of the supernate analyses, while the solids (sump and slurry) results will be reported in a supplemental report. The analytical data from the decon frit supernate indicate that all of the radionuclide, organic, and inorganic concentrations met the limits in Revision 4 of the Effluent Treatment Plant (ETP) Waste Acceptance Criteria (WAC) with the exception of boron. The ETP WAC limit for boron is 15.0 mg/L while the average measured concentration (based on quadruplicate analysis) was 15.5 mg/L. The measured concentrations of Li, Na, and Si were also relatively high in the supernate analysis. These results are consistent with the relatively high measured value of B given the compositional make-up of Frit 418. Given these results, it was speculated that either (a) Frit 418 was dissolving into the supernate or aqueous fraction and/or (b) fine frit particulates were carried forward to the analytical instrument based on the sampling procedure used (i.e., the supernate samples were not filtered - only settled with the liquid fraction being transferred with a pipette). To address this issue, a filtered supernate sample (using a 0.45 um filter) was prepared and submitted for analysis. The results of the filtered sample were consistent with 'unfiltered or settled' sample - relatively high values of B, Li, Na, and Si were found. This suggests that Frit 418 is dissolving in the liquid phase which could be enhanced by the high surface area of the frit fines or particulates in suspension. Based on the results of this study, it is recommended that DWPF re-evaluate the technical basis for the B WAC limit (the only component that exceeds the ETP WAC limit from the supernate analyses) or assess if a waiver or exception can be obtained for exceeding this limit. Given the possible dissolution of B, Li, Na, and Si into the supernate (due to dissolution of frit), DWPF may need to assess if the release of these frit components into the supernate are a concern for the disposal options being considered. It should be noted that the results of this study may not be representative of future decon frit solutions or sump/slurry solids samples. Therefore, future DWPF decisions regarding the possible disposal pathways for either the aqueous or solid portions of the Decon Frit system need to factor in the potential differences. More specifically, introduction of a different frit or changes to other DWPF flowsheet unit operations (e.g., different sludge batch or coupling with other process streams) may impact not only the results but also the conclusions regarding acceptability with respect to the ETF WAC limits.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis of Bismuth Functionalized Grapheme Oxide for Radioactive Iodine Gas Removal - 16114

Released radioactive iodine from nuclear reactors and nuclear severe accidents, such as those experienced at Chernobyl and Fukushima, is one of the most hazardous materials and can affect human health. Uptake of radioactive iodine from gaseous and aqueous waste, consisting of mainly organic forms such as methyl iodide and elemental iodine after reacting with organic matter in scrubber process, is a recent concern during nuclear power plant operation. In general, Triethylenediamine (TEDA) or KI-impregnated activated carbons, silver-loaded silica aerogels, and silver-loaded zeolite are used to remove radioactive iodine compounds. However, previous research has shown TEDA and KI-impregnated activated carbons to have some limitations for use in responding to severe accidents or in pressurized-water reactors, because they are easily burned up and the iodine removal efficiency of silver-loaded sorbents is greatly decreased at high temperatures. To improve the capability of synthesized sorbent material used in iodine gas removal, highly efficient sorbents for methyl and elemental iodine removal were prepared through the functionalization of graphene oxide (GO) with bismuth. GO was synthesized from natural graphite powder (99.95%) by the modified Hummers method, and then mixed with Bi(NO{sub 3}){sub 3}.5H{sub 2}O. After developing a sorbent for the removal of iodine, the synthesized sorbent was characterized using x-ray diffraction, a scanning electron microscope/energy dispersive spectrometer, and thermogravimetric analysis/differential scanning calorimetry, and the surface area of sorbents was determined using the BET-N{sub 2} adsorption method. Methyl iodine batch experiments were conducted for 7 days and elemental iodine gas adsorption experiments were conducted at high temperature (190 deg. C) using a carrier gas (air). The final concentration of iodine in batch and off-gas scrubber solutions (0.1 M NaOH) was analyzed using inductively coupled plasma mass spectrometry. The breakthrough curve and decontamination factor values were also investigated using bismuth-functionalized GO and the results were compared with Ag-zeolite, Sn-apatite, and activated carbon. (authors)

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Nitrate Conversion of HB-Line Reillex™ HPQ Resin

Reillex™ HPQ ion exchange resin is used by HB Line to remove plutonium from aqueous streams. Reillex™ HPQ resin currently available from Vertellus Specialties LLC is a chloride ionic form, which can cause stress corrosion cracking in stainless steels. Therefore, HB Line Engineering requested that Savannah River National Laboratory (SRNL) convert resin from chloride form to nitrate form in the Engineering Development Laboratory (EDL). To perform this task, SRNL treated two batches of resin in 2012. The first batch of resin from Reilly Industries Batch 80302MA was initially treated at SRNL in 2001 to remove chloride. This batch of resin, nominally 30 liters, has been stored wet in carboys since that time until being retreated in 2012. The second batch of resin from Batch 23408 consisted of 50 kg of new resin purchased from Vertellus Specialties in 2012. Both batches were treated in a column designed to convert resin using downflow of 1.0 M sodium nitrate solution through the resin bed followed by rinsing with deionized water. Both batches were analyzed for chloride concentration, before and after treatment, using Neutron Activation Analysis (NAA). The resin specification [Werling, 2003] states the total chlorine and chloride concentration shall be less than 250 ppm. The resin condition for measuring this concentration is not specified; however, in service the resin would always be fully wet. Measurements in SRNL showed that changing from oven dry resin to fully wet resin, with liquid in the particle interstices but no supernatant, increases the total weight by a factor of at least three. Therefore, concentration of chlorine or chloride expressed as parts per million (ppm) decreases by a factor of three. Therefore, SRNL recommends measuring chlorine concentration on an oven dry basis, then dividing by three to estimate chloride concentration in the fully wet condition. Chloride concentration in the first batch (No.80302MA) was nearly the same before the current treatment (759 ppm dry) and after treatment (745 ppm dry or ~248 ppm wet). Treatment of the second batch of resin (No.23408) was very successful. Chloride concentration decreased from 120,000 ppm dry to an average of 44 ppm dry or ~15ppm wet, which easily passes the 250 ppm wet criterion. Per guidance from HB Line Engineering, SRNL blended Batch 80302 resin with Batch P9059 resin which had been treated previously by ResinTech to remove chloride. The chloride concentrations for the two drums of Batch P9059 were 248 ppm dry (~83 ppm wet) ±22.8% and 583 ppm dry (~194 ppm wet) ± 11.8%. The blended resin was packaged in five gallon buckets.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗