Search NASA⌕ Search

SEARCH · Search NASA

Results for “bleed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Flowfield Measurements Inside a Boundary-Layer Bleed Slot

An experimental investigation was conducted to determine the flowfield inside a bleed slot used to control an oblique shock-wave and turbulent boundary-layer interaction. The slot was oriented normal to the primary flow direction and had a width of 1.0 cm (primary flow direction) and a length of 2.54 cm and spanned 16.5 cm. The approach boundary layer upstream of the interaction was nominally 3.0 cm thick. Two operating conditions were studied: M = 1.98 with a shock generator deflection angle of 6 deg and M = 2.46 with a shock generator deflection angle of 8 deg. Measurements include surface and flowfield static pressure, pitot pressure, and total mass flow through the slot. The results show that despite an initially two-dimensional interaction for the zero-bleed-flow case, the slot does not remove mass uniformly in the spanwise direction. Inside the slot, the flow is characterized bv two separation regions, which significantly reduce the effective flow area. The upper separation region acts as an aerodynamic throat, resulting in supersonic flow through much of the slot.

Davis, D. O.↗
NASA NTRS1997

Effect of Flow Misalignment and Multi-Hole Interaction on Boundary-Layer Bleed Hole Flow Coefficient Behavior

The effect of flow misalignment on the flow coefficient behavior of a 20 deg. boundary-layer bleed hole and the effect of the interaction between two 90 deg. bleed holes separated by two hole diameters on flow coefficient behavior has been studied experimentally. Both tests were run at freestream Mach numbers of 0.61, 1.62 and 2.49. The flow misalignment study was conducted over a range of 0 to 30 deg. The results show that neither flow misalignment nor hole interaction has much effect on the flow coefficient for the subsonic case. For the supersonic cases, flow misalignment causes significant degradation in the performance of the slant hole. For the supersonic normal hole interaction cases, depending on the hole orientation, either an increase or decrease in overall flow coefficient was observed. The largest change in flow coefficient, 6% increase at near choke conditions, occurred when the holes were oriented in line with the flow direction.

Davis, David O.↗
NASA NTRS1961

The Effect of Air Bleed on the Heat Transfer and Pressure Distribution on 30 Conical Flares at a Mach Number of 6.8

The effect of a boundary-layer bleed at the start of a 30 deg half-angle flare upon the shape of the flow boundaries, the pressure distribution on the flare, and the heat transfer to the flare was studied at a Mach number of 6.8. The forebody was an ogive cylinder. Test Reynolds numbers, based on forebody length, ranged from 1 x 10(exp 6) to 7.4 x 10(exp 6). Schlieren photographs showed the effect produced upon the flow boundaries by varying the dimensions of the bleed in both the radial and axial directions and by blunting the lip at the leading edge of the flare. The heat transfer and pressure distribution on the flare were correlated with the shape and nature of the flow boundaries.

Crawford, Davis H.↗
NASA NTRS2003

Asymmetric Base-Bleed Effect on Aerospike Plume-Induced Base-Heating Environment During Power-Pack Out

A computational heat transfer design methodology was developed to study tbe dual-engine linear aerospike plume-induced base-heating environment during one power-pack out, in ascent flight. It includes a three-dimensional, finite volume, viscous, chemically reacting, and pressure-based computational fluid dynamics formulation, a special base-bleed boundary condition, and a three-dimensional, finite volume, and spectral-line-based weighted-sum-of-gray-gases absorption computational radiation heat transfer formulation. A separate radiation model was used for diagnostic purposes. The computational methodology was systematically benchmarked. in this study, near-base radiative heat fluxes were computed, and they compared well with those measured during static linear aerospike engine tests. The base-heating environment of 18 trajectory points secected from three power-pack out scenarios was computed. The computed asymmetric base-heating physics were analyzed. The power-pack out condition has the most impact on convective base heating when it happens early in flight. The soume of its impact comes from the asymmetric and reduced base bleed.

Wang, Ten-See↗
NASA NTRS2004

Asymmetric Base-Bleed Effect on Aerospike Plume-Induced Base-Heating Environment

A computational heat transfer design methodology was developed to study the dual-engine linear aerospike plume-induced base-heating environment during one power-pack out, in ascent flight. It includes a three-dimensional, finite volume, viscous, chemically reacting, and pressure-based computational fluid dynamics formulation, a special base-bleed boundary condition, and a three-dimensional, finite volume, and spectral-line-based weighted-sum-of-gray-gases absorption computational radiation heat transfer formulation. A separate radiation model was used for diagnostic purposes. The computational methodology was systematically benchmarked. In this study, near-base radiative heat fluxes were computed, and they compared well with those measured during static linear aerospike engine tests. The base-heating environment of 18 trajectory points selected from three power-pack out scenarios was computed. The computed asymmetric base-heating physics were analyzed. The power-pack out condition has the most impact on convective base heating when it happens early in flight. The source of its impact comes from the asymmetric and reduced base bleed.

Wang, Ten-See↗