Search NASA⌕ Search

SEARCH · Search NASA

Results for “boron removal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Fabrication of a Cryogenic Terahertz Emitter for Bolometer Focal Plane Calibrations

A fabrication process is reported for prototype emitters of THz radiation, which operate cryogenically, and should provide a fast, stable blackbody source suitable for characterization of THz devices. The fabrication has been demonstrated and, at the time of this reporting, testing was underway. The emitter is similar to a monolithic silicon bolometer in design, using both a low-noise thermometer and a heater element on a thermally isolated stage. An impedance-matched, high-emissivity coat ing is also integrated to tune the blackbody properties. This emitter is designed to emit a precise amount of power as a blackbody spectrum centered on terahertz frequencies. The emission is a function of the blackbody temperature. An integrated resistive heater and thermometer system can control the temperature of the blackbody with greater precision than previous incarnations of calibration sources that relied on blackbody emission. The emitter is fabricated using a silicon- on-insulator substrate wafer. The buried oxide is chosen to be less than 1 micron thick, and the silicon device thickness is 1-2 microns. Layers of phosphorus compensated with boron are implanted into and diffused throughout the full thickness of the silicon device layer to create the thermometer and heater components. Degenerately doped wiring is implanted to connect the devices to wire-bondable contact pads at the edge of the emitter chip. Then the device is micromachined to remove the thick-handle silicon behind the thermometer and heater components, and to thermally isolate it on a silicon membrane. An impedance- matched emissive coating (ion assisted evaporated Bi) is applied to the back of the membrane to enable high-efficiency emission of the blackbody spectrum.

Chervenak, James↗
NASA NTRS1976

Longitudinal residual stresses in boron fibers

A method of measuring the longitudinal residual stress distribution in boron fibers is presented. The residual stresses in commercial CVD boron on tungsten fibers of 102, 142, and 203 microns (4, 5.6, and 8 mil) diameters were determined. Results for the three sizes show a compressive stress at the surface 800 to -1400 MN/sq m 120 to -200 ksi), changing monotonically to a region of tensile stress within the boron. At approximately 25 percent of the original radius, the stress reaches a maximum tensile 600 to 1000 MN/sq m(90 to 150 ksi) and then decreases to compressive near the tungsten boride core. The core itself is under a compressive stress of approximately -1300 MN/sq m (-190 ksi). The effects of surface removal on core residual stress and core-initiated fracture are discussed.

Behrendt, D. R.↗
DOE OSTI2025

In situ Detection of Plasma Induced Surface Interaction based on Deep Learning based Visual Diagnostics (Technical Report)

It is characteristic for many plasma devices to undergo plasma-material interaction leading to surface erosion. These processes, often not easily detectable, lead to changes in device performance and lifespan. State-of-the-art lifetime tests and wear experiments require over 1000s hours. A self-consistent model for accurately predicting the erosion's effects is not available. In situ detection of these processes is not a trivial task since the surface variations at the early stages have a micron scale. Such limitations not only restrict testing and prediction capabilities but also slow the development of new thrusters and limit mission duration. To address these challenges, an in-situ diagnostic for real-time erosion assessment has been developed, aiming to expedite lifetime testing and broaden experimental campaigns. Several works were dedicated to real-time and in situ monitoring of material erosion during plasma exposure using laser holography, microscopy, and with telemicroscopes. However, the applicability of these approaches is limited due to complexity, cost and less flexibility as they often require placing diagnostic equipment inside the vacuum chamber. In collaboration with Princeton Collaborative Research Facility (PCRF), Princeton Plasma Physics Laboratory (PPPL), a new diagnostic approach is developed, where geometry modifications to the ceramic channel walls were introduced that would result in accelerated channel erosion. We employed Long-distance microscope (LDM) imagery, combined with Deep-Learning based Shape from focus or depth from focus (DFF or SFF) approach, that provides an accessible and cost-effective solution. LDM employs focus variation techniques to continuously capture multiple images of the target object at distinct focal planes. DFF, an optical focus variation method, generates a 3D topographical surface depth map from a sequence of variably focused images. Combined with the developed diagnostic, this approach offers a controllable means to study erosion under accelerated conditions. In this work, we develop Neural Network-based DFF algorithm applicable for LDM data to quantitatively evaluate plasma induced surface modification from LDM data. Next, we develop Deep Learning-based super-resolution depth map image reconstruction technique to increase the resolution of depth maps obtained from DFF algorithm to improve the accuracy of erosion measurements. Thirdly, we develop several image processing techniques to remove noise and improve the quality of depth map image. Here we report the results of initial tests for this approach. An experimental setup designed and built in PPPL was employed that consists of a 3-cm gridded ion source that produces a neutralized argon beam with energies up to 600 eV. A hexagonal boron nitride (h-BN) ceramic target, designed based on computational predictions, was used. Tests were conducted to reconstruct the complex geometry of the target under the lighting conditions of the operated ion source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2000

Sub-Optical Lithography With Nanometer Definition Masks

Nanometer feature size lithography represents a major paradigm shift for the electronics and micro-electro-mechanical industries. In this paper, we discuss the capacity of dynamic focused reactive ion beam (FIB) etching systems to undertake direct and highly anisotropic erosion of thick evaporated gold coatings on boron-doped silicon X-ray mask membranes. FIB offers a new level of flexibility in micro fabrication, allowing for fast fabrication of X-ray masks, where pattern definition and surface alteration are combined in the same step which eliminates the whole lithographic process, in particular resist, resist development, electro-deposition and resist removal. Focused ion beam diameters as small as 7 nm can be obtained enabling fabrication well into the sub-20 nm regime. In preliminary demonstrations of this X-ray mask fabrication technique 22 nm width lines were milled directly through 0.9 microns of gold and a miniature mass spectrometer pattern was milled through over 0.5 microns of gold. Also presented are the results of the shadow printing, using the large depth of field of synchrotron high energy parallel X-ray beam, of these and other sub-optical defined patterns in photoresist conformally coated over surfaces of extreme topographical variation. Assuming that electronic circuits and/or micro devices scale proportionally, the surface area of devices processed with X-ray lithography and 20 nm critical dimension X-ray masks would be 0.5% that of contemporary devices (350 nm CD). The 20 CD mask fabrication represents an initial effort - a further factor of three reduction is anticipated which represents a further order-of-magnitude reduction in die area.

Hartley, Frank T.↗
DOE OSTI2026

Combustion synthesis of nanoscale magnesium borides with improved hydrogen uptake and release

The overarching goal of the reported project was to develop reversible metal hydrides that can be dehydrogenated and recharged at relatively low temperatures and pressures. The project complemented the research on reversible metal hydrides for hydrogen storage conducted by the Hydrogen Materials – Advanced Research Consortium (HyMARC). The students involved were trained at both the University of Texas at El Paso (UTEP) and Sandia National Laboratories (SNL). The research objectives were to fabricate nanoscale magnesium boride powders with different B/Mg atomic ratios and to investigate the effects of B/Mg ratio and particle size on the hydrogenation properties of the obtained materials. Magnesium diboride (MgB 2 ) and tetraboride (MgB 4 ) were synthesized by using combustion synthesis and by heating in a tube furnace. The latter method resulted in materials with significantly reduced impurity levels. An effective method for the removal of magnesium oxide impurities was identified. High-energy ball milling produced submicron MgB 2 and MgB 4 powders. However, hydrogenation experiments at pressures up to 700 bar have not shown any uptake of hydrogen. Thermogravimetric analysis of the decomposition of the obtained MgB 2 and MgB 4 demonstrated higher thermodynamic stability of the latter. Thus, the boron-rich nature and phase stability of magnesium borides with high B/Mg ratios make them poor candidates for direct hydrogenation. However, the synthesized MgB 4 is a promising energetic additive to solid fuels for high-speed air-breathing propulsion as it offers a lower oxidation onset temperature and greater energy density than MgB 2 .

08 HYDROGEN↗
DOE OSTI2025

Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride

The difficult ignition of boron decreases the combustion efficiency of boron-loaded, fuel-rich propellants. One approach to solving this problem involves the use of magnesium diboride (MgB2), which ignites easier than boron. Magnesium tetraboride (MgB4) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures were recently recognized as promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their thermal decomposition, oxidation, and combustion. The MgB2 and MgB4 powders were fabricated by combustion synthesis in the chemical oven mode and by heating Mg/B mixtures in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by high-energy ball milling. Thermal decomposition and oxidation of the obtained MgB₂ and MgB₄ powders were investigated by conducting non-isothermal thermogravimetric analysis (TGA) at temperatures up to 1550 °C in argon and oxygen flows. Combustion of B, MgB₂, and MgB₄ powders with oxygen at atmospheric pressure was studied in a windowed chamber using laser ignition and high-speed video recording. The TGA has shown multi-step decomposition of both magnesium borides in an argon environment. The maximum oxidation rate of MgB4 in oxygen was observed at a much lower temperature than in the case of MgB2. In the combustion experiments, both magnesium borides burned much faster than submicron boron. Ball milling of the borides further increased their burning rates. It has been concluded that nanoscale magnesium tetraboride is a promising ingredient for fuel-rich propellants owing to its high energy density, efficient oxidation, and rapid combustion.

Molina, Andre [The University of Texas at El Paso]↗
DOE OSTI2024

Elemental profiling and genomewide association studies reveal genomic variants modulating ionomic composition in Populus trichocarpa leaves

Samples were collected from a population of 1,089 black cottonwood genotypes (P. trichocarpa) assembled from native stands to encompass the central portion of the natural range of the species, stretching from 38.8° to 54.3° N Q13 latitude from California, USA, to British Columbia, Canada. Establishment of the common garden, growth conditions, and site maintenance have been described by Muchero et al (2015). In this study, leaf samples for ionomic profiling were collected from 4-year-old trees, during the growing season, in July 2012, from a field located in Clatskanie, Oregon, USA (46°6′11″N 123°12′13″W). The field site was located in a protected alluvial floodplain containing a uniform Wauna-Locoda silt loam soil area characterized by an acidic pH, in Columbia County, Oregon. A subset of 584 out of the 1,089 P. trichocarpa genotypes were represented in this sampling. These genotypes were randomly selected to represent the geographical distribution of the population. A single fully mature (LPI 7-9) leaf on the south side of the tree exposed to full sunlight conditions was removed from the tree within a 6-hour window centering on solar noon and immediately frozen under dry ice before processing. Leaf samples of 584 P. trichocarpa genotypes were finely ground to 40 mm particle size using a mortar and pestle, and ionomic composition was analyzed using ICP-MS. In total, 20 elements were profiled, including aluminum (Al27), arsenic (As75), boron (B11), cadmium (Cd111), calcium (Ca43), cobalt (Co), copper (Cu), iron (Fe57), magnesium (Mg25), manganese (Mn55), molybdenum (Mo), nickel (Ni60), phosphorus (P31), potassium (K39), rubidium (Rb85), selenium (Se82), sodium (Na23), strontium (Sr88), sulfur (S34), and zinc (Zn66), following a protocol established by Ziegler et al. (2013). For each sample, 75mg of powder was digested overnight in 2.5 mL HNO3 containing 20 parts per billion (ppb) indium as an internal standard, following the protocol described in Ziegler et al. (2013). Following a dilution, concentration of the 20 elements was measured using an Elan 6000 DRC-e mass spectrometer (Perkin-Elmer SCIEX) connected to a PFA microflow nebulizer (Elemental Scientific) and Apex HF desolvator (Elemental Scientific). One measurement per sample per genotype was done. For subsequent analyses, the quantifications were converted to total element concentration.

CBI ionomics, GWAS, plasma-mass spectrometry, neut↗
DOE OSTI2025

Fabrication and characterization of nanoscale magnesium diboride and tetraboride for propulsion and hydrogen storage applications

Abstract: Boron-loaded propellants have the potential to dramatically increase the performance of solid fuel ramjets, ducted rockets, and hybrid rocket engines. However, difficult ignition of boron decreases the combustion efficiency of these propellants. One approach to solving this problem involves the use of magnesium diboride, MgB2, which ignites easier than boron. Magnesium tetraboride, MgB4, potentially offers greater energetic performance as B has a higher energy density than Mg. However, the effect of the higher boron/metal ratio on the ignition and combustion is unclear. Nanoscale MgB2 particles and quasi 2D structures are promising propellant ingredients, but the oxidation and combustion properties of nanoscale MgB4 remain unknown. Nanoscale magnesium borides are also of interest as precursors for the synthesis of magnesium borohydride, Mg(BH4)2, a promising hydrogen storage material, but hydrogenation of MgB4 has not been studied yet. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their hydrogen uptake, thermal decomposition, oxidation, and combustion. The powders were fabricated by combustion synthesis and by heating in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by ball-mill exfoliation. The hydrogen intake of the obtained magnesium borides was examined at 700 bar and 300 ℃ and did not reveal any advantage of MgB4 over MgB2. Their thermal decomposition and oxidation were investigated with thermogravimetric analysis (TGA), while their combustion was studied using laser ignition and high-speed video recording. TGA has confirmed prior observations of multistep decomposition of magnesium borides, where each step involves formation of a boride with a higher B/Mg ratio and evaporation of formed magnesium. The oxidation rates of the borides are much higher than that of boron at temperatures over 1200 °C for MgB2 and over 900 °C for MgB4. The burning rates of non-milled MgB₂ and MgB₄ powders were much higher than for the used submicron boron. Milling the MgB₂ and MgB₄ powders further increased their burning rates. The milled MgB4 burned 7.5 times faster than submicron boron.

Combustion of metals, Solid fuels, Propellants, Hy↗
NASA NTRS2014

Chemical Sharpening, Shortening, and Unzipping of Boron Nitride Nanotubes

Boron nitride nanotubes (BNNTs), the one-dimensional member of the boron nitride nanostructure family, are generally accepted to be highly inert to oxidative treatments and can only be covalently modifi ed by highly reactive species. Conversely, it is discovered that the BNNTs can be chemically dispersed and their morphology modifi ed by a relatively mild method: simply sonicating the nanotubes in aqueous ammonia solution. The dispersed nanotubes are significantly corroded, with end-caps removed, tips sharpened, and walls thinned. The sonication treatment in aqueous ammonia solution also removes amorphous BN impurities and shortened BNNTs, resembling various oxidative treatments of carbon nanotubes. Importantly, the majority of BNNTs are at least partially longitudinally cut, or "unzipped". Entangled and freestanding BN nanoribbons (BNNRs), resulting from the unzipping, are found to be approximately 5-20 nm in width and up to a few hundred nanometers in length. This is the fi rst chemical method to obtain BNNRs from BNNT unzipping. This method is not derived from known carbon nanotube unzipping strategies, but is unique to BNNTs because the use of aqueous ammonia solutions specifi cally targets the B-N bond network. This study may pave the way for convenient processing of BNNTs, previously thought to be highly inert, toward controlling their dispersion, purity, lengths, and electronic properties.

Liao, Yunlong↗
DOE OSTI2022

MELCOR Accident Progression and Source Term Demonstration Calculations for a Heat Pipe Reactor

MELCOR is an integrated thermal hydraulics, accident progression, and source term code for reactor safety analysis that has been developed at Sandia National Laboratories for the United States Nuclear Regulatory Commission (NRC) since the early 1980s. Though MELCOR originated as a light water reactor (LWR) code, development and modernization efforts have expanded its application scope to includ e non-LWR reactor concepts. Current MELCOR development efforts include providing the NRC with the analytical capabilities to support regulatory readiness for licensing non-LWR techno logies under Strategy 2 of the NRC?s near- term Implementation Action Plans. Beginning with the Next Generation Nuclear Project (NGNP), MELCOR has undergone a range of enha ncements to provide analytical capabilities for modeling the spectrum of advanced non-LWR concepts. This report describes the generic plant model developed to demonstrate MELCOR capabilities to perform heat pipe reactor (HPR) safety evaluations. The generic plant mode l is based on a publicly-available Los Alamos National Laboratory (LANL) Megapower design as modified in the Idaho National Laboratory (INL) Design A description. For plant aspects (e.g., reactor building size and leak rate) that are not described in the LANL and INL references , the analysts made assumptions needed to construct a MELCOR full-plant model. The HP R uses high assay, low-enrichment uranium (HALEU) fuel with steel cladding that uses heat pipes to transfer heat to a secondary Brayton air cycle. The core region is surrounded by a stainless-steel shroud, alumina reflector, core barrel and boron carbide neutron shield. The reactor is secured inside a below-grade cavity, with the operating floor located above the cavity. Example calculations are performed to show the plant response and MELCOR capabilities to characterize a range of accident conditions. The accidents selected for evaluation consider a range of degraded and failed modes of operation for key safety functions providing re activity control, the primary and secondary system heat removal, and the effectiveness of th e confinement natural circulation flow into the reactor cavity (i.e., a flow blockage).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Neutral but Impactful: Gallium Cluster-Induced Nanopores from Beam-Blanked Gallium Ion Sources

Neutral atoms originating from liquid metal ion sources are an often-overlooked source of contamination and damage in focused ion beam microscopy. Beyond ions and single atoms, these sources also generate atom clusters. While most studies have investigated charged clusters, here we demonstrate that neutral clusters are also formed. These neutral clusters bypass the electrostatic beam blanking system, allowing them to impinge on samples even when the ion beam is blanked. We investigate this phenomenon using thin (≤20 nm) freestanding membranes of hexagonal boron nitride, silicon, and silicon nitride as targets. Randomly dispersed nanopores that form upon neutral cluster exposure are revealed. The average nanopore diameter is ∼2 nm with a narrow size distribution, suggesting that the atom clusters have a preferred size. Various electron microscopy techniques are used to characterize the nanopores, including high-resolution transmission electron microscopy, multislice ptychography, and electron energy-loss spectroscopy. Finally, we show how electron irradiation in the transmission electron microscope can be used to both remove any amorphous material that may clog the pores and to controllably grow the pores to specific sizes. Tunable nanopores such as these are interesting for nanofluidic applications requiring size-selective membranes.

Byrne, Dana O↗
DOE OSTI2025

High-Rate Sputter Deposition of Ultrathick Boron Carbide Coatings on Rolling Spherical Substrates

Amorphous boron carbide (B 4 C) is a promising next-generation ablator material for inertial confinement fusion. However, the deposition of ultrathick B4C coatings with submicron-scale density uniformity on spherical substrates, as required for ablator shell fabrication, remains challenging. Here, in this study, we use direct current magnetron sputtering to deposit B 4 C onto 2-mm-diameter Si spheres rolling in a dish-shaped substrate holder. High deposition rates of ∼3 μm/h are achieved. Ultrathick films have a columnar microstructure, with the column width determined by the density of nodular defects. Nodular defect nucleation is dominated by the pickup of particulates from the holder during substrate rolling. We demonstrate the fabrication of a hollow B 4 C spherical shell with a wall thickness of 80 μm. Also demonstrated is the laser machining of holes in the B 4 C coating, which is necessary for both the chemical removal of the Si template and the attachment of a fusion fuel fill tube.

Inertial confinement fusion targets↗
NASA NTRS1980

Empirical study of the interaction of silicon substrate thinness, device design, and solar cell processing

Processing experiments using wire-saw techniques to slice thin silicon wafers are described. Substrates were sliced directly to 17 mil, 8 mil, and 5 mil thicknesses. Some of the 8 mil substrates and all of the 5 mil substrates were chemically etched to 7 and 4 mils, respectively, to guarantee removal of any saw damage. The wafers wire sawed to 17 mil thicknesses were processed as reference cells. A baseline process which results in an n(+)-p cell structure, and two advanced processes which provide n(+)-p-p(+) structures were utilized. By using a p(+) enhancement layer on the solar cell back surface, the performance of the 7 mil wafers was increased to exceed that of the 17 mil solar cells with simple n(+)-p structures. Cells fabricated by an ion implantation sequence utilizing elemental boron and phosphorus implants were shown to be capable of equalling or exceeding the performance of cells fabricated by an equivalent all-diffusion process.

Pryor, R. A.↗
DOE OSTI2026

Ion-Specific Precipitation of Extractants Enables Rare-Earth Separation and Wastewater Remediation from Solvent Extraction of Critical Elements

The increasing demand for rare-earth elements (REEs) necessitates sustainable recovery strategies, particularly from secondary sources, such as electronic waste. Solvent extraction is the primary industrial method for REE separation; however, the unintentional dissolution of extractants into wastewater poses serious environmental risks, leading to organic contamination and process inefficiencies. Existing wastewater treatment methods struggle to remove these persistent pollutants, underscoring the need for innovative recovery approaches. Herein, we present a ligand-mediated precipitation strategy that simultaneously recovers REEs and removes dissolved extractants from solvent extraction wastewater. We show that residual extractants in the aqueous phase can selectively bind REEs, inducing their precipitation while leaving transition metals in solution. By integrating FTIR spectroscopy, EDS, XPS, EXAFS, and SAXS, we elucidate the mechanism of ion-specific precipitation and the local coordination environment of metal ions in the precipitate. Importantly, we demonstrate that the precipitated extractants can be efficiently recovered and reused, providing a closed-loop solution that enhances sustainability. Applying this method to leachates from samarium–cobalt (Sm–Co) and neodymium–iron–boron (NdFeB) mixed magnets, we achieve highly selective REE precipitation under mild conditions, demonstrating a scalable and cost-effective pathway for REE recovery, wastewater purification, and extractant recycling. In conclusion, by integrating element-specific ligand-mediated precipitation with extractant reuse, this work offers a transformative approach to REE separation that reduces the environmental impact while improving resource efficiency.

E-waste↗
NASA NTRS1985

Fatigue crack propagation of nickel-base superalloys at 650 deg C

The 650 C fatigue crack propagation behavior of two nickel-base superalloys, Rene 95 and Waspaloy, is studied with particular emphasis placed on understanding the roles of creep, environment, and two key grain boundary alloying additions, boron and zirconium. Comparison of air and vacuum data shows the air environment to be detrimental over a wide range of frequencies for both alloys. More in-depth analysis on Rene 95 shows at lower frequencies, such as 0.02 Hz, failure in air occurs by intergranular, environmentally-assisted creep crack growth, while at higher frequencies, up to 5.0 Hz, environmental interactions are still evident but creep effects are minimized. The effect of B and Zr in Waspaloy is found to be important where environmental and/or creep interactions are presented. In those instances, removal of B and Zr dramatically increases crack growth and it is therefore plausible that effective dilution of these elements may explain a previously observed trend in which crack growth rates increase with decreasing grain size.

Gayda, J.↗
NASA NTRS1988

Fatigue crack propagation of nickel-base superalloys at 650 deg C

The 650 C fatigue crack propagation behavior of two nickel-base superalloys, Rene 95 and Waspaloy, is studied with particular emphasis placed on understanding the roles of creep, environment, and two key grain boundary alloying additions, boron and zirconium. Comparison of air and vacuum data shows the air environment to be detrimental over a wide range of frequencies for both alloys. More in-depth analysis on Rene 95 shows at lower frequencies, such as 0.02 Hz, failure in air occurs by intergranular, environmentally-assisted creep crack growth, while at higher frequencies, up to 5.0 Hz, environmental interaction are still evident but creep effects are minimized. The effect of B and Zr in Waspaloy is found to be important where environmental and/or creep interactions are presented. In those instances, removal of B and Zr dramatically increases crack growth and it is therefore plausible that effective dilution of these elements may explain a previously observed trend in which crack growth rates increase with decreasing grain size.

Gayda, J.↗
NASA NTRS2018

Methods for Intercalating and Exfoliating Hexagonal Boron Nitride

Methods that facilitate exfoliation of hexagonal boron nitride (hBN), exfoliated hBN, and associated intermediate products are disclosed. Such a method can include the acts of mixing a sample of hBN with an activation agent (e.g., NaF, etc.) and a selected set of chemicals (e.g., a metal chloride) and intercalating the set of chemicals into the hBN to obtain intercalated hBN. Additionally, such a method can include the acts of hydrating the set of chemicals (i.e., the intercalates), and converting the set of chemicals to a set of oxide nanoparticles when exfoliating the intercalated hBN. The exfoliated hBN can be washed (e.g., with HCl, etc.) to remove remaining nanoparticles.

Hung, Ching-cheh↗