Results for “carbon fiber” — Page 5

NASA NTRS2019

The Effect of Impact Damage Next to Holes on the Bearing Strength of Carbon Fiber Laminates

This study was undertaken as a follow-on to a previous study that examined the effect of hole quality in the bearing strength of carbon fiber laminates. After the author of that previous study had established that hole quality had little effect on the ultimate bearing strength for carbon fiber laminates, the question was raised as to the effects of impact damage next to a hole on the bearing strength of that hole. While this is an unlikely scenario, it is still possible that this may occur on a launch vehicle structure and thus warranted study. After a literature review, results of a few studies on the hole-impact interaction with respect to resulting damage for carbon fiber laminates were found, but none that specifically addressed the resulting bearing strength. In reference 2, it was found that the holes and impact could interact to develop matrix splits. However, the lay-ups used in this study consisted of clumped plies [04/904]S, which are much more prone to matrix splitting than a laminate that would actually be used in practice (such as a lay-up of [0/90]4S). This study also focused on the analytical aspects of the problem rather than the experimental results. Reference 3 also used [04/904]S laminates (clumped plies) and examined the damage morphology, determining that, as the impact damage neared the hole, the damage zone became more asymmetrical. The effect this would have on bearing strength was not addressed. The experimental work presented in this study was to develop empirical data relating holeimpact damage effects on the resulting bearing strength of a commonly used (quasi-isotropic) lay-up of carbon fiber laminate. The emphasis was not on the morphology of the resulting damage, as it was in references 2 and 3, but rather on the practical aspects of how this damage affected the bearing strength and how this compared to the companion study1 on the effect of hole quality on the bearing strength of the laminate.

Nettles, A. T.↗

NASA NTRS2004

Carbon-Fiber Brush Heat Exchangers

Velvetlike and brushlike pads of carbon fibers have been proposed for use as mechanically compliant, highly thermally conductive interfaces for transferring heat. A pad of this type would be formed by attaching short carbon fibers to either or both of two objects that one desires to place in thermal contact with each other. The purpose of using a thermal-contact pad of this or any other type is to reduce the thermal resistance of an interface between a heat source and a heat sink.

Knowles, Timothy R.↗

NASA NTRS2015

Puncture-Healing Thermoplastic Resin Carbon-Fiber-Reinforced Composites

A composite comprising a combination of a self-healing polymer matrix and a carbon fiber reinforcement is described. In one embodiment, the matrix is a polybutadiene graft copolymer matrix, such as polybutadiene graft copolymer comprising poly(butadiene)-graft-poly(methyl acrylate-co-acrylonitrile). A method of fabricating the composite is also described, comprising the steps of manufacturing a pre-impregnated unidirectional carbon fiber preform by wetting a plurality of carbon fibers with a solution, the solution comprising a self-healing polymer and a solvent, and curing the preform. A method of repairing a structure made from the composite of the invention is described. A novel prepreg material used to manufacture the composite of the invention is described.

Gordon, Keith L.↗

NASA NTRS2017

Puncture-Healing Thermoplastic Resin Carbon-Fiber Reinforced Composites

A composite comprising a combination of a self-healing polymer matrix and a carbon fiber reinforcement is described. In one embodiment, the matrix is a polybutadiene graft copolymer matrix, such as polybutadiene graft copolymer comprising poly(butadiene)-graft-poly(methyl acrylate-co-acrylonitrile). A method of fabricating the composite is also described, comprising the steps of manufacturing a pre-impregnated unidirectional carbon fiber preform by wetting a plurality of carbon fibers with a solution, the solution comprising a self-healing polymer and a solvent, and curing the preform. A method of repairing a structure made from the composite of the invention is described. A novel prepreg material used to manufacture the composite of the invention is described.

Gordon, Keith L.↗

NASA NTRS1980

Carbon Fibers Conductivity Studies

In an attempt to understand the process of electrical conduction in polyacrylonitrile (PAN)-based carbon fibers, calculations were carried out on cluster models of the fiber consisting of carbon, nitrogen, and hydrogen atoms using the modified intermediate neglect of differential overlap (MINDO) molecular orbital (MO) method. The models were developed based on the assumption that PAN carbon fibers obtained with heat treatment temperatures (HTT) below 1000 C retain nitrogen in a graphite-like lattice. For clusters modeling an edge nitrogen site, analysis of the occupied MO's indicated an electron distribution similar to that of graphite. A similar analysis for the somewhat less stable interior nitrogen site revealed a partially localized II electron distribution around the nitrogen atom. The differences in bonding trends and structural stability between edge and interior nitrogen clusters led to a two-step process proposed for nitrogen evolution with increasing HTT.

Yang, C. Y.↗

NASA NTRS1979

Carbon Fiber Risk Analysis

The scope and status of the effort to assess the risks associated with the accidental release of carbon/graphite fibers from civil aircraft is presented. Vulnerability of electrical and electronic equipment to carbon fibers, dispersal of carbon fibers, effectiveness of filtering systems, impact of fiber induced failures, and risk methodology are among the topics covered.

Source record↗

NASA NTRS1983

Properties of carbon fibers with various coatings

It is shown that all high modulus carbon fibers are durable with respect to thermal oxidation in air. Among the more widely used and economical materials with low modulus, Celion displays particularly good oxidative durability at high temperatures. This contrast to other materials is due to the low content of Natrium and Kalium in Celion carbon fibers. It is also noted that improved characteristics are attained in Celion carbon fiber/polyimide systems when fibers are used with high temperature resistant polyimide coatings.

Seegel, V.↗

NASA NTRS1980

High-voltage spark carbon-fiber sticky-tape data analyzer

An efficient method for detecting carbon fibers collected on a stick tape monitor was developed. The fibers were released from a simulated crash fire situation containing carbon fiber composite material. The method utilized the ability of the fiber to initiate a spark across a set of alternately biased high voltage electrodes to electronically count the number of fiber fragments collected on the tape. It was found that the spark, which contains high energy and is of very short duration, is capable of partially damaging or consuming the fiber fragments. It also creates a mechanical disturbance which ejects the fiber from the grid. Both characteristics were helpful in establishing a single discharge pulse for each fiber segment.

Yang, L. C.↗

NASA NTRS1980

Process modifications for improved carbon fiber composites: Alleviation of the electrical hazards problem

Attempts to alleviate carbon-fiber-composite electrical hazards during airplane crash fires through fiber gasification are described. Thermogravimetric and differential scanning calorimetric experiments found several catalysts that caused fibers to combust when composites were exposed to test fires. Composites were tested in the 'Burn-Bang' apparatus and in high voltage electrical detection grid apparatus. In a standard three minute burn test modified composites released no fibers, while state-of-the-art composites released several hundred fiber fragments. Expected service life with and without catalytic modification was studied and electron microscopy and X-ray microanalysis furnished physical appearance and chemical composition data. An acrylic acid polymer fiber coating was developed that wet the carbon fiber surface uniformly with the catalyst, providing a marked contrast with the uneven coats obtained by solution-dipping.

Ramohalli, K.↗

NASA NTRS1983

Structure and growth process of vapor-grown carbon fibers

The structure, effect of heat, and growth process of vapor-grown carbon fibers are investigated. The growth process of the carbon fibers could be divided into three stages; nucleation, elongation, and thickening processes. Also, a multi-layered structure can be produced as well as graphitization.

Koyama, T.↗

NASA NTRS1988

Thermoplastic coated carbon fibers for textile preforms

A continuous process for producing prepreg from carbon fiber and thermoplastic matrix is described. After the tow has been spread using a pneumatic device, the process utilizes a fluidized bed to apply thermoplastic powder to the bundle. Finally, direct electrical heating of the coated fiber tow melts the polymer on the individual fibers, creating a uniform and extremely flexible prepreg. The efficiency of the process was evaluated during initial trials in which a thermoplastic polyimide, LaRC-TPI, was applied to T-300, 3K (3000 filament) carbon fiber tow. The physical properties of unidirectional composite specimens fabricated from this prepreg were measured, and the matrix uniformity and void content of the samples was determined. The results of these evaluations are detailed and discussed.

Allen, L. E.↗

NASA NTRS1980

As assessment of power system vulnerability to release of carbon fibers during commercial aviation accidents

The vulnerability of a power distribution system in Bedford and Lexington, Massachusetts to power outages as a result of exposure to carbon fibers released in a commercial aviation accident in 1993 was examined. Possible crash scenarios at Logan Airport based on current operational data and estimated carbon fiber usage levels were used to predict exposure levels and occurrence probabilities. The analysis predicts a mean time between carbon fiber induced power outages of 2300 years with an expected annual consequence of 0.7 persons losing power. In comparison to historical outage data for the system, this represents a 0.007% increase in outage rate and 0.07% increase in consequence.

Larocque, G. R.↗

NASA NTRS1984

Chemical Modification of the Surface of High Modulus Carbon Fibers

The deposition of selected monomers on the surface of high modulus carbon fibers was studied. The fundamental principles which provide the basis for the design of a predictable interfacial bond between carbon fibers and polymeric matrices are described.

Source record↗

NASA NTRSDate not supplied

Simulation of etch pit formation through active sites in carbon fiber micro-structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation as a result of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gasses such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRS1988

Halogenation Enhances Carbon-Fiber/Epoxy Composites

Interlaminar shear strength increased by inexpensive treatment. New surface treatment for carbon fibers enhances interlaminar shear strength, ILSS, without altering tensile strength significantly. Exposure of polyacrylonitrile-based T-300, or equivalent, fibers to bromine vapor at room temperature improves ILSS of epoxy composites made from these fibers by 30 percent. Enhanced ILSS obtained from halogenation of carbon fibers beneficial in many aerospace and terrestrial applications.

Jaworske, Donald A.↗

NASA NTRS1980

A probabilistic analysis of electrical equipment vulnerability to carbon fibers

The statistical problems of airborne carbon fibers falling onto electrical circuits were idealized and analyzed. The probability of making contact between randomly oriented finite length fibers and sets of parallel conductors with various spacings and lengths was developed theoretically. The probability of multiple fibers joining to bridge a single gap between conductors, or forming continuous networks is included. From these theoretical considerations, practical statistical analyses to assess the likelihood of causing electrical malfunctions was produced. The statistics obtained were confirmed by comparison with results of controlled experiments.

Elber, W.↗