Search NASA⌕ Search

SEARCH · Search NASA

Results for “cascade performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A cascaded coding scheme for error control and its performance analysis

A coding scheme for error control in data communication systems is investigated. The scheme is obtained by cascading two error-correcting codes, called the inner and outer codes. Its error performance is analyzed for a binary symmetric channel with bit-error rate epsilon less than 1/2. It is shown that, if the inner and outer codes are chosen properly, high reliability can be attained even for a high-channel bit-error rate. Specific examples with inner codes ranging from high rates and Reed-Solomon codes as outer codes are considered, and their error probabilities evaluated. They all provide high reliability even for high bit-error rates, say 0.1-0.01. Several example schemes are being considered for satellite and spacecraft downlink error control.

Kasami, Tadao↗
NASA NTRS2015

Application of Pinniped Vibrissae to Aeropropulsion

Vibrissae of Phoca Vitulina (Harbor Seal) and Mirounga Angustirostris (Elephant Seal) possess undulations along their length. Harbor Seal Vibrissae were shown to reduce vortex induced vibrations and reduce drag compared to appropriately scaled cylinders and ellipses. Samples of Harbor Seal vibrissae, Elephant Seal vibrissae and California Sea Lion vibrissae were collected from the Marine Mammal Center in California. CT scanning, microscopy and 3D scanning techniques were utilized to characterize the whiskers. Computational fluid dynamics simulations of the whiskers were carried out to compare them to an ellipse and a cylinder. Leading edge parameters from the whiskers were used to create a 3D profile based on a modern power turbine blade. The NASA SW-2 facility was used to perform wind tunnel cascade testing on the 'Seal Blades'. Computational Fluid Dynamics simulations were used to study incidence angles from -37 to +10 degrees on the aerodynamic performance of the Seal Blade. The tests and simulations were conducted at a Reynolds number of 100,000. The Seal Blades showed consistent performance improvements over the baseline configuration. It was determined that a fuel burn reduction of approximately 5 could be achieved for a fixed wing aircraft. Noise reduction potential is also explored.

wakes↗
DOE OSTI2020

A signal compensation based cascaded PI control for an industrial heat exchange system

Since the characteristics of the industrial heat exchange system (HES) are drastically affected by variations of the steam pressure, ambient temperature and water quality, it is difficult for the classical cascade PI control system to meet the desirable control objectives. Therefore, in this paper, a deterministic linear model with unmodeled dynamics is used to describe the dynamic characteristics of the HES. It should be noted that the unmodeled dynamics at the previously sampled instant can be calculated using actual measurements and that the tracking error, which includes effects of the rate of changes of unmodeled dynamics on the controlled model, can be accurately determined. An additional compensating signal is obtained with the feedforward control together with a one-step optimal control law. Consequently, the cascade PI control strategy with the signal compensation is established. Furthermore, the simulation and industrial application show that the proposed method can effectively improve the performance of the cascade PI control system, especially when the unmodeled dynamics is subjected to unknown variations.

42 ENGINEERING↗
DOE OSTI2024

Heating performance of a vapor compression heat pump cascaded with a thermoelectric heat pump

Air source heat pumps (ASHPs) are widely utilized for heating and cooling in residential buildings; however, their effectiveness in heating mode is compromised during extreme weather conditions. Extensive research endeavors have been undertaken to develop, test, and assess a cost-effective vapor compression ASHP suitable for cold climate regions. Further, this study takes an innovative approach by developing component and system prototypes for a cold climate heat pump. This design combines a thermoelectric heat pump (TEHP) with a traditional residential split ASHP to augment heating capacity in low ambient temperature conditions. The component and system prototypes underwent experimental testing in the psychrometric chambers. The experimental findings revealed a 13.6% to 13.7% increase in total heat pump heating capacity, accompanied by a 3.1% to 5.0% decrease in the coefficient of performance (COP) at ambient temperatures of -15°C and -19°C, when compared to the original ASHP. The COP of the TEHP is relatively constant, ranging from 1.63 to 1.76. This prototype offers a solution to address the challenges associated with reduced heat pump capacity at low ambient temperatures. The experimental results indicated that the lower the ambient temperature, thermoelectric heat pump auxiliary heating can increase the heating efficiency 60% in comparison to electric resistance.

42 ENGINEERING↗
NASA NTRS1987

Scale model test results of a thrust reverser concept for advanced multi-functional exhaust systems

An evaluation is made of scale model test results for a 'block-and-turn' thrust reverser design consisting of an internal flow blocker, internal doors, two ports located on the top and bottom of the exhaust duct, cascade-turning vanes located at the port exit to turn the flow, and external doors which guide the exhaust flow. Numerous geometric variations were incorporated in order to obtain parametric aerodynamic design criteria. The baseline reverser configuration exceeded predicted levels of performance. Skewed vane cascade concepts can be as effective in turning the flow as the baseline vane concept.

Kuchar, A. P.↗
NASA NTRS1984

Design and performance of a fixed, nonaccelerating, guide vane cascade that operates over an inlet flow angle range of 60 deg

A unique set of wind tunnel guide vanes are designed with an inverse design code and analyzed with a panel method and an integral boundary layer code developed at the NASA Lewis Research Center. The fixed guide vanes, 80 feet long with 6-foot chord length, were designed for the NASA Ames 40 x 80/80 x 120 ft Wind Tunnel. Low subsonic flow is accepted over a 60 deg range of inlet angle from either the 40 x 80 leg or the 80 x 120 leg of the wind tunnel, and directed axially into the main leg of the tunnel where drive fans are located. Experimental tests of 1/10-scale models were conducted to verify design calculations.

Sanz, J. M.↗
NASA NTRS1981

Energy efficient engine high-pressure turbine supersonic cascade technology report

The performance of two vane endwall geometries and three blade sections for the high-pressure turbine was evaluated in terms of the efficiency requirements of the Energy Efficient Engine high-pressure turbine component. The van endwall designs featured a straight wall and S-wall configuration. The blade designs included a base blade, straightback blade, and overcambered blade. Test results indicated that the S-wall vane configuration and the base blade configuration offered the most promising performance characteristics for the Energy Efficient Engine high-pressure turbine component.

Kopper, F. C.↗
NASA NTRS1985

Design and performance of a fixed, nonaccelerating guide vane cascade that operates over an inlet flow angle range of 60 deg

A unique set of wind tunnel guide vanes are designed with an inverse design code and analyzed with a panel method and an integral boundary layer code developed at the NASA Lewis Research Center. The fixed guide vanes, 80 feet long with 6-foot chord length, were designed for the NASA Ames 40 x 80/80 x 120 ft Wind Tunnel. Low subsonic flow is accepted over a 60 deg range of inlet angle from either the 40 x 80 leg or the 80 x 120 leg of the wind tunnel, and directed axially into the main leg of the tunnel where drive fans are located. Experimental tests of 1/10-scale models were conducted to verify design calculations.

Sanz, J. M.↗
NASA NTRSDate not supplied

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗
NASA NTRSDate not supplied

Modified Cascading Generalized Inverse Control Allocation

The current aviation revolution towards electric propulsion aircraft (e.g., electric vertical takeoff-and-landing) brings unique control challenges. These vehicles are typically over-actuated (more effectors than desired control outcomes), may require control strategies for the three phases of flight (hover, transition and cruise), and currently have limited electric power availability. These vehicle challenges bring the need for optimal control allocation to the forefront of research. A leading control allocation algorithm, used in current flight vehicles, is the Cascading Generalized Inverse (CGI). Unfortunately, the Cascading Generalized Inverse algorithm is unable to achieve some desired outcomes, it intermittently provides non-optimal allocations, and it may fail to preserve moment direction near maximal achievable outcomes. In this research, the shortcomings of the Cascading Generalized Inverse algorithm are addressed by augmenting the algorithm with Scalar Difference Quadratic unsaturation identification and location at each iteration. Rigorous theory is shown that the Modified Cascading Generalized Inverse performs better at obtaining optimal allocations for all attainable outcomes. Numerical case studies for over-actuated vehicles demonstrate resolution to the aforementioned deficiencies.

Control Allocation↗
NASA NTRS1990

Experimental investigation of oscillating cascade aerodynamics

A series of experiments are performed in the NASA Lewis Transonic Oscillating Cascade Facility to provide fundamental data quantifying the high subsonic and transonic steady and oscillating aerodynamics of a biconvex airfoil cascade at realistic reduced frequency values for all interblade phase angles. This is accomplished by developing and utilizing an unsteady aerodynamic influence-coefficient technique in which only one cascaded airfoil is oscillated at a time. The vector summation of the resulting airfoil-surface unsteady pressures (measured on a dynamically instrumented airfoil) makes it possible to determine the unsteady aerodynamics of an equivalent cascade with all airfoils oscillating at any specified interblade phase angle.

Buffum, Daniel H.↗
NASA NTRS2010

Multiple Differential-Amplifier MMICs Embedded in Waveguides

Compact amplifier assemblies of a type now being developed for operation at frequencies of hundreds of gigahertz comprise multiple amplifier units in parallel arrangements to increase power and/or cascade arrangements to increase gains. Each amplifier unit is a monolithic microwave integrated circuit (MMIC) implementation of a pair of amplifiers in differential (in contradistinction to single-ended) configuration. Heretofore, in cascading amplifiers to increase gain, it has been common practice to interconnect the amplifiers by use of wires and/or thin films on substrates. This practice has not yielded satisfactory results at frequencies greater than 200 Hz, in each case, for either or both of two reasons: Wire bonds introduce large discontinuities. Because the interconnections are typically tens of wavelengths long, any impedance mismatches give rise to ripples in the gain-vs.-frequency response, which degrade the performance of the cascade.

Kangaslahti, Pekka↗
NASA NTRS1975

Calculation of the radio emission from EAS

Time-varying features of an electron-photon cascade are considered, particularly those associated with radio emission. The cosmic ray shower is represented as a superposition of collinear 10 GeV electron-photon cascades launched at different heights in the atmosphere. Actual simulations are performed for only 10 cascades at each of 40 heights and the results are scaled to represent the total number of cascades required. The apparent angular motions of the cascade particles as detected by antennas located at various positions up to 300 m from the shower axis are simulated. The radio pulse waveform and the corresponding frequency spectrum are obtained from these motions.

Allan, H. R.↗