Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Enhancing Oxygen Reduction Activity and Cr Tolerance of Solid Oxide Fuel Cell Cathodes by a Multiphase Catalyst Coating

Intermediate temperature solid oxide fuel cells (IT-SOFCs) are cost-effective and efficient energy conversion systems. Here, the sluggish oxygen reduction reaction (ORR) and the degradation of cathodes are critical challenges to the commercialization of IT-SOFCs. Here, a highly efficient multiphase (MP) catalyst coating, consisting of Ba 1–x Co 0.7 Fe 0.2 Nb 0.1 O 3–δ (BCFN) and BaCO 3 , to enhance the ORR activity and durability of the state-of-the-art lanthanum strontium cobalt ferrite (La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3–δ , LSCF) cathode is reported. The conformal MP catalyst-coated LSCF cathode shows a polarization resistance (R p ) of 0.048 Ω cm 2 at 650 °C, about one order of magnitude smaller than that of the bare LSCF. In an accelerated Cr-poisoning test, the degradation rate of the catalyst-coated LSCF electrode is 10 –3 Ω cm 2 h –1 (0.59% h –1 ) over 200 h, only one fifth of the degradation rate of the bare LSCF electrode at 750 °C. In addition, anode-supported single cells with the MP catalyst-coated LSCF cathode show a dramatically enhanced peak power density (1.4 W cm –2 vs 0.67 W cm –2 at 750 °C) and increased durability against Cr and H 2 O. Both experimental results and density functional theory-based calculations indicate that the BCFN phase improves the ORR activity while the BaCO 3 phase enhances the stability of the LSCF cathode.

solid oxide fuel cells↗

Potassium Prussian blue-coated Li-rich cathode with enhanced lithium ion storage property

With high specific capacity, the layered Li-rich Mn-based oxide (LRMO) is a promising candidate cathode material for Li-ion batteries. However, the irreversible release of Li-ions during the first charging process, instability of LRMO/electrolyte interface and relatively low ion conductivity of LRMO result in low initial Coulombic efficiency (ICE), poor cycle stability and rate performance, which prohibit its further application. Furthermore, interface engineering via additive coating is expected to effectively address these issues. Herein, we rely on potassium Prussian blue (KPB), a Li + acceptor with good ion conductivity, as a new coating material on LRMO particles. The KPB coating not only forms a protective layer on the surface of LRMO against electrolyte corrosion, but also functions as a host for Li + transport and accommodation, leading to enhanced ion conductivity and ICE of LRMO cathode. Consequently, 2 wt% KPB coated LRMO cathode achieved an initial discharge capacity of up to 281.7 mA h g -1 with an ICE of 85.69% compared to an ICE of 79.52% for the LRMO cathode without coating. The cycling and rate performance are also greatly improved as evidenced by the well maintained capacity of up to 176.8 mA h g -1 after 100 cycles at a current density of 0.5 C, compared to the limited capacity of only 135.3 mA h g -1 for the LRMO cathode without coating. Overall, this work pioneers the use of potassium Prussian blue as additive coating material to enhance performance of LRMO cathode, and we expect it to inspire the battery community with new strategies of material engineering/design toward practical application in high-energy lithium-ion batteries.

25 ENERGY STORAGE↗

A robust and active hybrid catalyst for facile oxygen reduction in solid oxide fuel cells

The sluggish oxygen reduction reaction (ORR) greatly reduces the energy efficiency of solid oxide fuel cells (SOFCs). In this work, we present our results in dramatically enhancing the ORR kinetics and durability of the state-of-the-art La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) cathode using a hybrid catalyst coating composed of a conformal PrNi 0.5 Mn 0.5 O 3 (PNM) thin film with exsoluted PrOx nanoparticles. At 750 °C, the hybrid catalyst-coated LSCF cathode shows a polarization resistance of ~0.022 Ω cm 2 , about 1/6 of that for a bare LSCF cathode (~0.134 Ω cm 2 ). Further, anode-supported cells with the hybrid catalyst-coated LSCF cathode demonstrate remarkable peak power densities (~1.21 W cm –2 ) while maintaining excellent durability (0.7 V for ~500 h). Near Ambient X-ray Photoelectron Spectroscopy (XPS) and Near Edge X-Ray Absorption Fine Structure (NEXAFS) analyses, together with density functional theory (DFT) calculations, imply that the oxygen-vacancy-rich surfaces of the PrOx nanoparticles greatly accelerate the rate of electron transfer in the ORR whereas the thin PNM film facilitates rapid oxide-ion transport while drastically enhancing the surface stability of the LSCF electrode.

Chen, Yu↗

Impact of polymer additives on crack mitigation of rod-coated fuel cell cathode catalyst layers

Cracks in catalyst layers (CLs) are a potential source of long-term failure in a fuel cell membrane electrode assembly (MEA). While modifications to the CL ink formulation can affect the degree of cracking, these changes may lead to lower initial performance than their cracked analogues due to the established link between formulation and performance. In this work, we explored the use of polymeric additives to mitigate CL cracks. Small quantities of poly (acrylic acid), poly (ethylene oxide), poly (methyl methacrylate), or poly (vinyl alcohol) - 5 wt% relative to ionomer mass - were added to the ink prior to its final mixing. Poly (vinyl alcohol) resulted in crack-free CLs, whereas the other polymers resulted in CLs with similar crack percentages as the control CL. Through a combination of transmission electron microscopy, X-ray computed tomography, and infrared spectroscopy, we ascribed the crack-mitigating mechanism of poly (vinyl alcohol) to its ability to hydrogen-bond with Nafion, the ion conducting polymer binder in the catalyst ink. Initial performance of this non-cracked electrode exhibited nearly identical electrochemical behavior to its cracked counterpart, demonstrating that PVA additives successfully reduce cracks while maintaining cell initial performance.

30 DIRECT ENERGY CONVERSION↗

Safe and Durable High-Temperature Lithium–Sulfur Batteries via Molecular Layer Deposited Coating

Here, Lithium-sulfur (Li-S) battery is a promising high energy storage candidate in electric vehicles. However, the commonly employed ether based electrolyte does not enable to realize safe high-temperature Li-S batteries due to the low boiling and flash temperatures. Traditional carbonate based electrolyte obtains safe physical properties at high temperature but does not complete reversible electrochemical reaction for most Li-S batteries. Here we realize safe high temperature Li-S batteries on universal carbon-sulfur electrodes by molecular layer deposited (MLD) alucone coating. Sulfur cathodes with MLD coating complete the reversible electrochemical process in carbonate electrolyte and exhibit a safe and ultrastable cycle life at high temperature, which promise practicable Li-S batteries for electric vehicles and other large-scale energy storage systems.

25 ENERGY STORAGE↗

Coated particles for lithium battery cathodes

Particles of cathodic materials are coated with polymer to prevent direct contact between the particles and the surrounding electrolyte. The polymers are held in place either by a) growing the polymers from initiators covalently bound to the particle, b) attachment of the already-formed polymers by covalently linking to functional groups attached to the particle, or c) electrostatic interactions resulting from incorporation of cationic or anionic groups in the polymer chain. Carbon or ceramic coatings may first be formed on the surfaces of the particles before the particles are coated with polymer. The polymer coating is both electronically and ionically conductive.

25 ENERGY STORAGE↗

Promising performance of sulfide catholytes compared to halide alternatives in NMC811 cathodes for sheet-type sulfide solid-state batteries

Sulfide-based solid-state batteries (SSBs) show promise in achieving energy densities over 350 Wh/kg, yet challenges persist with their incorporation of high-voltage, nickel-rich layered oxide cathodes, such as LiNi₀.₈Mn₀.₁Co₀.₁O₂ (NMC811), due to the poor oxidation stability of sulfide solid-state electrolytes (SSEs) like Li₆PS₅Cl (LPSCl). Although halide SSEs such as Li₃InCl₆ (LIC) and Li₃YCl₆ (LYC) have previously shown promise in stabilizing high-voltage NMC cathodes, our research reveals that sulfide SSE catholytes, particularly when combined with surface-coated NMC cathodes, deliver superior performance. Here, this investigation assesses the cycling stability of various catholytes—LPSCl, LIC, Li₁₀GeP₂S₁₂ (LGPS), combined LIC-LPSCl, and LYC-LPSCl—in SSBs with LiNbO₃-coated NMC811 cathodes against sheet-type LPSCl separators. Findings indicate that while LGPS-based cathodes maintain higher capacity retention, they yield lower deliverable capacity, and LIC cathodes experience significant electrochemical degradation. Importantly, our results underscore that sulfide SSE catholytes, in conjunction with LiNbO₃-coated cathodes, optimize the cathode-electrolyte interphase (CEI), enhancing both kinetics and mass transport. These insights provide a strategic direction for optimizing catholyte composition in the development of sheet-type sulfide-based SSBs.

Catholyte↗

Dual Protective Mechanism of AlPO 4 Coating on High-Nickel Cathode Material for High Energy Density and Long Cycle Life Lithium-Ion Batteries

Cathode material with high nickel content is a promising candidate for the future generation of Li-ion batteries (LIBs). However, severe structural degradation during cycling limits its practical use, especially for electric vehicles. Herein, AlPO 4 nanoparticles were synthesized and then coated onto the surface of a high-nickel layer-structured cathode via a dry coating method. The AlPO 4 nanoparticles coating significantly improved the cycling stability from 69.2% to over 80% capacity retention after 140 cycles. Furthermore, the structure and chemical composition of the AlPO 4 -coated cathode was investigated by XRD, SEM, XPS, and STEM. Compared with the non-coated cathode, we revealed a dual protective mechanism for enhanced cycling stability, where Al doping and Li 3 PO 4 coating play synergistic roles in protecting cathode material through long-term cycling. This work demonstrates a facile and environmentally friendly approach toward improving the performance of high-nickel LIB cathodes, which can be easily scaled up for industrial applications.

25 ENERGY STORAGE↗

The Application of Poly(3-hexylthiophene-2,5-diyl) as a Protective Coating for High Rate Cathode Materials

Poly (3-hexylthiophene-2,5-diyl) (P3HT), a conducting polymer studied extensively for its optoelectronic devices, offers a number of advantageous properties when used as a conductive binder for lithium-ion battery cathode materials. By mixing with carbon nanotubes (CNT), P3HTCNT serves as a surface coating for the cathode material LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA). Oxidation of the P3HT enables high electronic and ionic conductivity to be achieved over the potential range where the NCA is electrochemically active. In addition to the conductivity benefits from electrochemical doping, the P3HT-CNT coating suppresses electrolyte breakdown, thus inhibiting growth of the solid electrolyte interphase (SEI) layer and preventing intergranular cracking in the NCA particles. In conclusion, The use of the P3HT-CNT binder system leads to improved cycling for NCA at high power density with capacities of 80 mAh g -1 obtained after 1000 cycles at 16C, a value that is 4 times greater than what is achieved in the control electrode.

36 MATERIALS SCIENCE↗

Modification of polymer velvet cathode via metallic Mo coating for enhancement of high-current electron emission performances

The effect of surface Mo coating on the high-current electron emission performances for polymer velvet cathode has been investigated in a diode with A-K gap of 11.5 cm by the combination of time-resolved electrical diagnostic and temporal pressure variation. Compared with uncoated polymer velvet cathode under the single-pulsed emission mode, the Mo-coated one shows lower outgassing levels (∼0.40 Pa L), slower cathode plasma expansion velocity (∼2.30 cm/μs), and higher emission stability as evidences by the change in cathode current, temporal pressure variation, and diode perveance. Moreover, after Mo coating, the emission consistency of the polymer velvet cathode between two adjacent pulses is significantly improved in double-pulsed emission mode with ∼500 ns interval between two pulses, which further confirms the effectiveness of Mo coating for enhancement of electron emission performance of polymer velvet cathodes. These results should be of interest to the high-repetitive high-power microwave systems with cold cathodes.

36 MATERIALS SCIENCE↗

Beneficial rheological properties of lithium-ion battery cathode slurries from elevated mixing and coating temperatures

It is crucial that lithium-ion battery manufacturers implement strategies to expedite production without sacrificing quality due to rising consumer demand. Cathode coating is commonly performed at the industrial scale with a slot-die coater. In slot-die coating, substrate velocity is maximized and imperfections (such as air entrainment and thickness variations) are minimized by reducing the viscosity of the material being coated. A simple, scalable technique of reducing the viscosity of the cathode slurry is to increase its temperature, though it is dire that this heat does not cause irreversible gelation or otherwise deteriorate the slurry constituents. Cathode slurries were prepared at different mixing temperatures between 25 °C and 75 °C and their flow behavior was studied at their mixing temperature. At practical shear rates, the slurry coated at 60 °C was 23% less viscous than that coated at 25 °C, meaning the critical coating speed could be increased by roughly 14% at 60 °C. Between 25 °C and 60 °C, the slurries’ yield stress and equilibrium storage modulus increased monotonically, providing the additional benefit of higher sedimentation resistance of the active materials. To examine the influence of temperature on coating morphology and electrochemical performance, slurries were prepared and coated at 25 °C and 60 °C. Micrographs revealed no superficial differences between coatings. The electrode coated at 60 °C demonstrated comparable capacity retention during long-term cycling and high-rate discharge testing when compared to the electrode coated at 25 °C. The findings of this study indicate that warmer mixing and coating operations serve to maximize cathode productivity, particularly if advancements can be made in industrial-scale electrode drying.

25 ENERGY STORAGE↗

Descriptor-Based Analysis of Atomic Layer Deposition Mechanisms on Spinel LiMn 2 O 4 Lithium-Ion Battery Cathodes

Protective coatings have been shown to effectively suppress Mn ion dissolution from the spinel LiMn 2 O 4 lithium-ion battery cathode by stabilizing the surface against undesired side reactions with the electrolyte. In spite of extensive study, however, there remains a lack of atomic-scale understanding of how such coatings are deposited, and no molecular-level descriptor to predict trends in deposition mechanisms has been identified. We have recently shown that Al 2 O 3 coatings grown by atomic layer deposition (ALD) with alternating trimethylaluminum (TMA) and water exposures exhibit submonolayer growth because of precursor decomposition on the lithium manganate spinel (LMO) surface during early ALD pulses. In the present work, we elucidate the underlying mechanisms of this Al 2 O 3 ALD process using density functional theory (DFT) calculations and X-ray photoelectron spectroscopy (XPS) experiments, and we introduce a generalized descriptor-based framework to understand the resulting trends across a spectrum of surface structures and functionalities. We demonstrate that all decomposition products, including CH 3 -aluminum adducts and dissociated CH 3 groups, are Lewis bases and are coordinated to oxygen atoms on the LMO surface, leading to charge transfer to Lewis acidic Mn 3d states. Inert-transfer XPS supports these theoretical predictions, showing an increase in near-surface Mn 3+ content following TMA exposure and shifts in C is spectra consistent with C-O bond formation. We extend the DFT studies to various low- and high-index LMO surface facets, as a proxy for tuning the Lewis acid-base interactions between surface-bound CH 3 * and near-surface Mn ions. The thermochemistry for TMA reactions on these chemically distinct LMO surfaces demonstrates that ALD is structure-sensitive and that there is higher reactivity for TMA decomposition and Al 2 O 3 nucleation near LMO steps and defects. Motivated by the Lewis basic character of the decomposition products, we introduce the oxygen vacancy formation energy as a descriptor for decomposition energetics, and we demonstrate that all energetics are correlated to this quantity through the number of electrons that are transferred along the reaction coordinate. Finally, based on these findings, we hypothesize that improved electrochemical cycling with only 1-2 ALD cycles may be due to selective passivation of defect sites on the LMO surface that are more susceptible to Mn dissolution, and we suggest that similar descriptor-based analyses could be useful for the study of other ALD coatings on oxide substrates.

25 ENERGY STORAGE↗

Functioning Mechanism of AlF 3 Coating on the Li- and Mn-Rich Cathode Materials

We report systematic studies of the microstructural changes of uncoated and AlF3-coated Li-rich Mn-rich (LMR) cathode materials (Li1.2Ni0.15Co0.10Mn0.55O2) before and after cycling using a combination of aberration-corrected scanning/transmission electron microscopy (S/TEM) and electron energy loss spectroscopy (EELS). TEM coupled with EELS provides detailed information about the crystallographic and electronic structure changes that occur after cycling, thus revealing the fundamental improvement mechanism of surface coating. The results demonstrate that the surface coating reduces oxidation of the electrolyte at high voltage, suppressing the accumulation of a thick solid electrolyte interface (SEI) layer on electrode particle surface. Surface coating significantly enhances the stability of the surface structure and protects the electrode from severe etching/corrosion by the acidic species in the electrolyte, reducing the formation of etched surfaces and corrosion pits. Moreover, surface coating alleviates the undesirable voltage fade by mitigating layered to spinel-like phase transformation in the bulk region of the material. These fundamental findings may also be widely applied to explain the functioning mechanisms of other surface coatings used in a broad range of electrode materials.

Zheng, Jianming↗

A perspective on coatings to stabilize high-voltage cathodes: LiMn1.5Ni0.5O4 with subnanometer Lipon cycled with LiPF6 electrolyte

High voltage Li-ion cathodes push the limits of stability for both cathode and electrolyte. Here subnanometer coatings of an amorphous thin film electrolyte (Lipon) improved the room temperature and 60 C cycling stability of a LiMn1.5Ni0.5O4 spinel cathode when charged to 4.9V with a standard LiPF6 carbonate electrolyte. The cathodes delivered superior C-rate performances up to a 5C discharge, when compared to the uncoated cathodes. Enhanced performance extended for at least 100 cycles. Electrochemical impedance spectroscopy indicates that Lipon slows the increase of interface resistance. Thicker 1-3nm Lipon coatings are sufficiently insulating as to block electronic transport to the cathode particles. Thick coatings also slow Mn dissolution. Results suggest that Lipon may act to scavenge impurities or block active sites that promote electrolyte decomposition. While greatly improved by the Lipon coating, this cathode is not sufficiently stable for long cycle life applications. Further work is needed to assess if and what surface coatings will ultimately stabilize the high voltage cathodes. Comments include insight from other studies of Lipon coated cathodes and directions for future research.

Li-ion battery↗

High rate electrochemical performances of nanosized ZnO and carbon co-coated LiFePO{sub 4} cathode

The high rate electrochemical performances of ZnO and carbon co-coated LiFePO{sub 4} have been studied by X-ray diffraction, high-resolution transmission electron microscope, electrochemical impedance spectroscopy, cyclic voltammetry and galvanostatic measurements. The carbon coated LiFePO{sub 4} material was prepared by a freeze-drying method, and the diffusion coefficient and exchange current of these materials were calculated from their electrochemical impedance spectroscopy. The electrode delivered a reversible capacity of about 90% of the theoretical capacity when cycled between 2.5 and 4.2 V and showed stable cycle performance at high charge/discharge rates. This study showed that the co-coating process and freeze-drying method can effectively improve the electrochemical performances of LiFePO{sub 4} materials.

36 MATERIALS SCIENCE↗

An improved oxygen reduction reaction activity and CO 2 -tolerance of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ achieved by a surface modification with barium cobaltite coatings

Solid oxide fuel cells (SOFCs) cathode often suffers from the poisoning effect of the contaminants commonly encountered in air such as CO 2 . Here we report an effective approach to enhancing the activity and CO 2 tolerance of the state-of-the-art La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) cathode enabled by a coating of BaCoO 3-δ (BCO), as verified by the electrochemical testings, Raman analyses, and density functional theory calculations. When surface modified with a thin-film BCO coating, LSCF displays a much enhanced ORR activity and an improved durability against CO 2 . For example, anode supported SOFCs with the LSCF cathode coated with BCO coatings show a remarkable peak power density (Pmax) of 0.41 Wcm -2 and a significantly reduced degradation rate in current density of ~0.08% h -1 at 0.8 V and 700 °C for a period of 300 hs when humidified H2 (with 3 vol%H2O) was used as fuel and air with 8 vol% CO 2 as oxidant. The demonstrated performance is improved when compared with those of the cells with a blank LSCF electrode (a Pmax of ~0.36 Wcm -2 and a degradation rate of ~0.15% h -1 ) under the same conditions. Furthermore, the adsorption energy calculations suggests that BCO coating makes CO 2 adsorption much weaker than LSCF (-0.54 eV versus -1.07 eV).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗