Search NASA⌕ Search

SEARCH · Search NASA

Results for “cell temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of Metal Halides Treatment on High Throughput Low Temperature CIGS Solar Cells

Copper indium gallium diselenide (CIGS) semiconductor thin films were deposited at high rate and low temperature using single-stage thermal co-evaporation process on molybdenum back contact. A post deposition treatment was done by flashing AgBr at 350 ºC to induce recrystallization. Changes in morphology were confirmed by SEM, with an observed increase in grain size, as well as by XRD measurements, with a decrease in FWHM. Device results show an improvement of the performance after the AgBr vapor treatment, as all the photovoltaic parameters enhanced. Altogether, AgBr seems to be a suitable transport agent and beneficial for device fabrication.

14 SOLAR ENERGY↗
DOE OSTI2020

Resistance drift in Ge 2 Sb 2 Te 5 phase change memory line cells at low temperatures and its response to photoexcitation

Resistance drift in amorphous Ge 2 Sb 2 Te 5 is experimentally characterized in melt-quenched line cells in the range of 300 K to 125 K and is observed to follow the previously reported power-law behavior with drift coefficients in the range of 0.07 to 0.11 in the dark, linearly decreasing with 1/kT. While these drift coefficients measured in the dark are similar to commonly observed drift coefficients (~0.1) at and above room temperature, measurements under light show a significantly lower drift coefficient (0.05 under illumination vs 0.09 in the dark at 150 K). Periodic on/off switching of light shows a sudden decrease/increase in resistance, attributed to photo-excited carriers, followed by a very slow response (~30 min at 150 K) attributed to contribution of electron traps and slow trap-to-trap charge exchanges. A device-level electronic model is used to relate these experimental findings to gradual charging of electron traps in amorphous Ge 2 Sb 2 Te 5 , which gives rise to growth of a potential barrier for holes in time and, hence, resistance drift.

42 ENGINEERING↗
DOE OSTI2021

Shockley-Queisser analysis of the temperature-efficiency correlation of solar cells in the presence of non-radiative heat transfer

An empirical negative T cell − η correlation has been widely applied, without careful justifications, to evaluate the efficiency ( η ) increase of solar cells due to their temperature ( T cell ) decrease. Here, a framework is introduced to simultaneously compute T cell and η . This model confirms the negative T cell − η correlation if the above-bandgap absorptivity ( α I ) is not suppressed in the optimization of the sub-bandgap reflectivity ( ρ II ) or the infrared emissivity, otherwise it may suggest a positive correlation. It further gives a guideline to enhance η of silicon cells under typical conditions: every 1% increase of α I is equivalent to a 57% increase of ρ II .

14 SOLAR ENERGY↗
DOE OSTI2021

Improving Performance and Durability of Low Temperature Direct Ammonia Fuel Cells: Effect of Backpressure and Oxygen Reduction Catalysts

Low temperature direct ammonia fuel cells (DAFCs) are attractive for transportation applications. The primary obstacle to their commercial use is their low performance and poor durability. In the present work, we focus on improving DAFCs performance and durability by examining the effect of operating backpressure and oxygen reduction reaction (ORR) catalysts such as Acta 4020, Pd/C and Pt/C. DAFCs with Acta 4020 cathode can reach a peak power density of 390 mW cm -2 which is among the best reported performance, but they can be operated for a period of 11 h at 300 mA cm -2 . DAFCs with Pd/C cathode offer a moderate performance with a peak power density of 304 mW cm -2 , but has a much improved durability - a continuous operation for up to 36 h with a slow decay rate of ~1 mV h -1 at 300 mA cm -2 . In addition, the degradation pathways for DAFCs with Pd/C cathode are probed by characterizing the initial and final electrodes by XPS, suggesting that cathodic Pd dissolution occurs during the durability test.

Electrochemistry↗
DOE OSTI2022

Enforcing detailed balance in the Borgnakke–Larsen redistribution method with temperature dependent relaxation models

For decades, it has been observed that the commonly used Borgnakke–Larsen method for energy redistribution in Direct Simulation Monte Carlo codes fails to satisfy the principle of detailed balance when coupled to a wide variety of temperature dependent relaxation models, while seemingly satisfying detailed balance when coupled to others. Many attempts have been made to remedy the issue, yet much ambiguity remains, and no consensus appears in the literature regarding the root cause of the intermittent compatibility of the Borgnakke–Larsen method with temperature dependent relaxation models. This paper alleviates that ambiguity by presenting a rigorous theoretical derivation of the Borgnakke–Larsen method's requirement for satisfying detailed balance. Specifically, it is shown that the Borgnakke–Larsen method maintains detailed balance if and only if the probability of internal-energy exchange during a collision depends only on collision invariants (e.g., total energy). Here, the consequences of this result are explored in the context of several published definitions of relaxation temperature, including translational, total, and cell-averaged temperatures. Of particular note, it is shown that cell-averaged temperatures, which have been widely discussed in the literature as a way to ensure equilibrium is reached, also fail in a similar, although less dramatic, fashion when the aforementioned relationship is not enforced. The developed theory can be used when implementing existing or new relaxation models and will ensure that detailed balance is satisfied.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Improving Stability of Triple-Cation Perovskite Solar Cells under High-Temperature Operation

Metal halide perovskite photovoltaic performance required for commercial technology encompasses both efficiency and stability. Advances in both these parameters have recently been reported; however, these strategies are often difficult to directly compare due to differences in perovskite composition, device architecture, fabrication methods, and accelerated stressors applied in stability tests. In particular, it is found that there is a distinct lack of elevated temperature, operational (light and bias) stability data. Furthermore, significant testing is required to understand the interactions when combinations are used (e.g., additives used with posttreatments). Herein, individual and combined additive, posttreatment, and contact layer strategies from recent literature reports under standardized operational stability tests of p-i-n CsMAFA perovskites at 70 degrees C are evaluated. Through analysis of over 1000 devices, it is concluded that the hole-transport layer (HTL) is the most significant component impacting elevated temperature operational stability. This analysis motivates future development of high-performance HTLs.

14 SOLAR ENERGY↗
DOE OSTI2021

Load following power generation and power storage using REP and PEM technology

A hydrogen generation system for generating hydrogen and electrical power includes a power supply, a reformer-electrolyzer-purifier (REP) assembly including at least one fuel cell including an anode and a cathode separated by an electrolyte matrix, at least one low temperature fuel cell, and a hydrogen storage. The at least one fuel cell is configured to receive a reverse voltage supplied by the power supply and generate hydrogen-containing gas in the anode of the at least one fuel cell. The at least one low temperature fuel cell is configured to receive the hydrogen-containing gas output from the REP assembly. The at least one low temperature fuel cell is configured to selectably operate in a power generation mode in which the hydrogen-containing gas is used to generate electrical power and a power storage mode in which the hydrogen-containing gas is pressurized and stored in the hydrogen storage.

Jahnke, Fred C.↗
DOE OSTI2021

Long-Term Degradation of Passivated Emitter and Rear Contact Silicon Solar Cell under Light and Heat

Advanced designs enable high-efficiency solar cells; however, more complex structures create new long-term stability concerns. Herein, the long-term degradation processes affecting advanced silicon solar cells using laboratory-based illumination and heating over hundreds of hours are investigated. The activation energy for the degradation of voltage is estimated and the degradation rates to normal solar cell operating temperature ranges are extrapolated. The cell degradation observed at high temperatures in the lab is kinetically similar to the process affecting field-deployed modules contributing to 0.37% year-1 of annualized degradation. Electroluminescence and photoluminescence mapping show that the degradation is dominated by minority carrier lifetime reduction. Suns-open-circuit voltage and light beam-induced current results indicate that the degradation could result from passivation degradation at the surface or defect formation in the near-subsurface region, leading to increased minority carrier recombination. This work highlights a long-term degradation process under elevated temperature and illumination that may continue to affect cells in an irreversible manner that is separate from recoverable light-induced degradation and light- and elevated temperature-induced degradation.

14 SOLAR ENERGY↗
DOE OSTI2023

Mechanically induced thermal runaway severity analysis for Li-ion batteries

Thermal runaway is one of the most important safety concerns in the deployment of Li-ion batteries. For this study, we developed a standardized single-side indentation test protocol to induce an internal short-circuit. Cell voltage, temperature, and applied compressive force are monitored as a function of time. Each cell is given an observed hazard severity (OHS in five categories) modified from the EUCAR table. Meanwhile a calculated hazard severity (CHS) is obtained solely based on temperature and voltage curves. The calculation formula considers the cell temperature, rate of temperature increase, cell capacity, state of charge (SOC), voltage drop, and voltage drop rate. Each term is assigned with an appropriate weight to scale the calculated score from 0 to100. This method was applied to >100 Li-ion batteries with various SOCs and chemistries, and their OHS and CHS were displayed against SOC. The purpose is to provide battery designers, manufacturers, and end-users a clear comparison of thermal runaway severity of different batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Evaluation of temperature changes in a cell culture plate well with absorbing walls containing a 3D model of tumour spheroid under irradiation in the optical range

The temperature conditions for photodynamic therapy of the culture of tumour cells organised in 3D spheroids are studied. The spheroids are placed in the cell culture medium in the well of a special cell culture plate with absorbing walls. A mathematical model is presented that describes the temperature distribution in a well with a cell culture plate heated by optical radiation. It is shown that the temperature in the well volume is not uniformly distributed, and the temperature on the well surface can differ significantly from the temperature in its volume. (laser medicine)

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

LaCrO 3 -Coated La 0.6 Sr 0.4 Co 0.2 Fe0.8O3–δ Core–Shell Structured Cathode with Enhanced Cr Tolerance for Intermediate-Temperature Solid Oxide Fuel Cells

La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) is a common cathode material for intermediate temperature solid oxide fuel cells due to its excellent oxygen reduction reaction catalytic activity. However, the Cr-poisoning effect is a severe issue causing its electrochemical performance degrada-tion. To develop a LSCF-based cathode with excellent Cr-tolerance, LaCrO 3 -coated LSCF core-shell structured (LCr@LSCF) cathode was prepared via solution infiltration method. After coated by LCr shell, the long-term stability and Cr-tolerance were obviously improved, at the price of sacrificing some electrochemical performance. As a result, the development of LCr@LSCF cathode with eye-catching Cr-tolerance is of great significance to the commercialization of LSCF.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Improved Low Temperature Performance of Graphite/Li Cells Using Isoxazole as a Novel Cosolvent in Electrolytes

An investigation of novel electrolyte formulations to improve low temperature performance of Li/graphite half cells has been conducted. A novel electrolyte co-solvent, isoxazole (IZ), has been investigated in electrolyte systems composed of lithium difluoro(oxalato)borate (LiDFOB) in fluoroethylene carbonate (FEC) and LiDFOB in ethylene carbonate (EC). Cells containing 1 M LiDFOB FEC: IZ electrolyte have a significant improvement in capacity retention and reversible capacity at −10 °C. Ex-situ surface analysis of the cycled electrodes suggests that reduction of LiDFOB results in an oxalate rich solid electrolyte interphase (SEI). Addition of FEC, results in improved stability of the anode SEI preventing further decomposition of isoxazole solvent and improving cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Enhancement of low-temperature solid oxide fuel cell performance and durability via surface chemistry modification

The development of active cathodes is one of the most critical challenges to lowering the operating temperature for solid oxide fuel cells (SOFCs). Here, in this work, we demonstrated that by modifying the cathode surface chemistry at a relatively low temperature, the cathode activity and durability can be simultaneously enhanced on high-performing, low-temperature cathodes such as (La 0.6 Sr 0.4 ) 0.95 Co 0.2 Fe 0.8 O 3-δ (LSCF) and Sr 0.5 Sm 0.5 CoO 3-δ (SSC). This low-temperature modification using multi-valent cations activates the highly defected surface and maintains the nanoscale electrocatalysts by bypassing the high-temperature sintering procedure for SOFC fabrication. The modified cathode at 600°C shows an order of magnitude reduction in impedance to only 0.05 Ωcm 2 with a peak power density of 1.1 W/cm 2 and increases stability over 2000 h. The combination of in situ characterization, distribution of relaxation time analysis on impedance spectroscopy, and surface chemistry analysis reveals the importance of surface chemistry control on the gas-solid reaction activity and durability and provides the design principle for numerous future solid oxide cells.

25 ENERGY STORAGE↗
DOE OSTI2020

Sodium-halogen secondary cell

An intermediate temperature sodium-halogen secondary cell that includes a negative electrode compartment housing a negative, molten sodium-based electrode and a positive electrode compartment housing a current collector disposed in a highly conductive molten positive electrolyte. A sodium halide (NaX) positive electrode is disposed in a molten positive electrolyte comprising one or more AlX3 salts, wherein X may be the same or different halogen selected from Cl, Br, and I, wherein the ratio of NaX to AlX3 is greater than or equal to one. A sodium ion conductive solid electrolyte membrane separates the molten sodium negative electrode from the molten positive electrolyte. The secondary cell operates at a temperature in the range from about 80° C. to 210° C.

Bhavaraju, Sai↗
DOE OSTI2023

Optimizing liquid free ionomer binders for high-temperature polymer electrolyte membrane fuel cells for heavy duty vehicles

This report documents tech transfer from Penn State to Ionomer Solutions LLC for high-temperature polymer electrolyte membrane fuel cells. High-temperature polymer electrolyte membrane (HT-PEM) fuel cells are enticing power plants for heavy-duty vehicle (HDV) transportation because their elevated temperature operation fosters greater heat rejection through larger temperature differentials. In 2021, over 6 million battery electric light duty vehicles (LDVs) were sold. Conversely, only 19,000 LDVs using fuel cell power trains were sold in 2021. Given the meteoric rise of battery-based powertrains for LDVs and its projected growth, stakeholders for fuel cell technology for transportation have shifted their focus towards HDVs rather than LDVs given fuel cells specific and volumetric energy density advantage over batteries when the vehicle is large, heavy, and/or needs to move large distances before refueling.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

High-performance ammonia oxidation catalysts for anion-exchange membrane direct ammonia fuel cells

Low-temperature direct ammonia fuel cells (DAFCs) use carbon-neutral ammonia as a fuel, which has attracted increasing attention recently due to ammonia's low source-to-tank energy cost, easy transport and storage, and wide availability. However, current DAFC technologies are greatly limited by the kinetically sluggish ammonia oxidation reaction (AOR) at the anode. Herein, we report an AOR catalyst, in which ternary PtIrZn nanoparticles with an average size of 2.3 ± 0.2 nm were highly dispersed on a binary composite support comprising cerium oxide (CeO 2 ) and zeolitic imidazolate framework-8 (ZIF-8)-derived carbon (PtIrZn/CeO 2 -ZIF-8) through a sonochemical-assisted synthesis method. Additionally, the PtIrZn alloy, with the aid of abundant OH ad provided by CeO 2 and uniform particle dispersibility contributed by porous ZIF-8 carbon (surface area: ~600 m 2 g -1 ), has shown highly efficient catalytic activity for the AOR in alkaline media, superior to that of commercial PtIr/C. The rotating disk electrode (RDE) results indicate a lower onset potential (0.35 vs. 0.43 V), relative to the reversible hydrogen electrode at room temperature, and a decreased activation energy (~36.7 vs. 50.8 kJ mol -1 ) relative to the PtIr/C catalyst. Notably, the PtIrZn/CeO 2 -ZIF-8 catalyst was assembled with a high-performance hydroxide anion-exchange membrane to fabricate an alkaline DAFC, reaching a peak power density of 91 mW cm -2 . Unlike in aqueous electrolytes, supports play a critical role in improving uniform ionomer distribution and mass transport in the anode. PtIrZn nanoparticles on silicon dioxide (SiO 2 ) integrated with carboxyl-functionalized carbon nanotubes (CNT–COOH) were further studied as the anode in a DAFC. A significantly enhanced peak power density of 314 mW cm -2 was achieved. Density functional theory calculations elucidated that Zn atoms in the PtIr alloy can reduce the theoretical limiting potential of *NH 2 dehydrogenation to *NH by ~0.1 V, which can be attributed to a Zn-modulated upshift of the Pt–Ir d-band that facilitates the N–H bond breakage.

25 ENERGY STORAGE↗