Apollo extension system payloads. manned flying system /mps/ kinesthetic effects
Apollo project - kinesthetic effects of astronaut movements on center of gravity of lunar flight vehicle
SPACE VEHICLE↗
SEARCH · Search NASA
Results for “center of gravity”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Design definition study of a lift/cruise fan technology V/STOL aircraft. Volume 2: Technology aircraft
Technology flight vehicles were defined for three different approaches which demonstrate the concept and characteristics of the multipurpose aircraft established for Navy missions. The propulsion system used for the various technology flight vehicles was representative of that established for the multipurpose aircraft. Existing J97-GE100 gas generators were selected based on cost, availability and exhaust characteristics. The LF459 fans were also selected and are compatible with both technology and operational vehicles. To comply with the design guideline safety criteria, it was determined that three gas generators were required to provide engine out safety in the hover flight mode. The final propulsion system established for the technology aircraft was three existing J97 gas generators powering three LF459 fans. Different aircraft candidates were evaluated for application to the three designated design approaches. Each configuration was evaluated on the basis of (1) propulsion system integration, (2) modification required, (3) pilot's visibility, (4) payload volume, and (5) adaptability to compatible location of center-of-gravity/aerodynamic center and thrust center.
Source record↗
Modification of integrated partial payload lifting assembly
The Integrated Partial Payload Lifting Assembly (IPPLA) is currently used to transport and load experimental payloads into the cargo bay of the Space Shuttle. It is unable to carry the astronaut/passenger tunnel without a structural modification. The purpose of this design is to create a removalbe modification that will allow the IPPLA to lift and carry the passenger tunnel. Modifications evaluated were full-length insert beams which would extend through the existing strongback arms. These beam proposals were eliminated because of high cost and weight. Other proposals evaluated were attachments of cantilever beams to the existing strongback areas. The cantilever proposals reduced cost and weight compared to the full-length modifications. A third method evaluated was to simply make modifications to one side of the IPPLA therefore reducing the materials of the cantilever proposals by 40 percent. The design of the modification selected was completed with two channel beams jointly welded to a centered steel plate. The extension arm modification is inserted into the existing strongback channel beams and bolted into place. Two extension arms are added to one side of the IPPLA to provide the extra length needed to accommodate the passenger tunnel. The center counterbalance will then be offset about 20 inches to center gravity and therefore maintain horizontal status. The extension arm modification was selected because of minimum cost, low weight, and minimal installation time.
Groah, Melodie↗
Inertial processing of vestibulo-ocular signals
New evidence for a central resolution of gravito-inertial signals has been recently obtained by analyzing the properties of the vestibulo-ocular reflex (VOR) in response to combined lateral translations and roll tilts of the head. It is found that the VOR generates robust compensatory horizontal eye movements independent of whether or not the interaural translatory acceleration component is canceled out by a gravitational acceleration component due to simultaneous roll-tilt. This response property of the VOR depends on functional semicircular canals, suggesting that the brain uses both otolith and semicircular canal signals to estimate head motion relative to inertial space. Vestibular information about dynamic head attitude relative to gravity is the basis for computing head (and body) angular velocity relative to inertial space. Available evidence suggests that the inertial vestibular system controls both head attitude and velocity with respect to a gravity-centered reference frame. The basic computational principles underlying the inertial processing of otolith and semicircular canal afferent signals are outlined.
NASA Discipline Neuroscience↗
NASA Lewis Research Center low-gravity fluid management technology program
A history of the Lewis Research Center in space fluid management technology program is presented. Current programs which include numerical modeling of fluid systems, heat exchanger/radiator concept studies, and the design of the Cryogenic Fluid Management Facility are discussed. Recent analytical and experimental activities performed to support the Shuttle/Centaur development activity are highlighted.
Aydelott, J. C.↗
NASA Lewis Research Center low-gravity fluid management technology program
A history of the Lewis Research Center in space fluid management technology program is presented. Current programs which include numerical modeling of fluid systems, heat exchanger/radiator concept studies, and the design of the Cryogenic Fluid Management Facility are discussed. Recent analytical and experimental activities performed to support the Shuttle/Centaur development activity are highlighted.
Aydelott, J. C.↗
Wind-Tunnel Investigation of an Advanced General Aviation Canard Configuration
Wind-tunnel tests of a model of an advanced canard configuration designed for general aviation were conducted in the Langley 30- by 60-Foot Tunnel. The objective of the tests was to determine the aerodynamic stability and control characteristics of the configuration for a large range of angles of attack and sideslip at several power conditions. Analysis of the aerodynamic data indicates significant effects of power and of center-of-gravity location. For forward center-of-gravity locations, the configuration had extremely stall-resistant stability and control characteristics. For aft center-of-gravity locations and high-power conditions, the combined effects of increased pitch control and reduced longitudinal stability overpowered the stall resistance provided by the canard, which led to a high-angle-of-attack, deep-stall trim condition. Other aspects of the aerodynamic characteristics studied include the following: flow-visualization study, effect of negative angles of attack, lateral-directional characteristics, and comparison of the stall characteristics with another canard configuration.
Chambers, J. R.↗
Flight Measurements of Flying Qualities of a P-47D-30 Airplane (AAF No. 43-3441) to Determine Longitudinal Stability and Control and Stalling Characteristics
Flight tests have been made to determine the longitudinal stability and control and stalling characteristics of the P-47.E-30 airplane. The teat results show the airplane to be unstable stick free in any power-on condition even at the most forward center-of-gravity position tested. At the rearward center-of-gravity position tested the airplane also had neutral to negative stick-fixed stability with power on. The characteristics in accelerated flight were acceptable at the forward center-of-gravity position at low and high altitudes except at high speed where the control-force variations with acceleration were high. At the rearward center-of-gravity position, elevator-force reversals were experienced in turns at low speeds, and the force per g was low at all the other speeds. Ample stall warning was afforded in all the conditions tested and the stalling characteristics were very satisfactory except in the approach and wave-off conditions.
Kraft, Christopher C., Jr.↗
Forces and Moments on Sphere-Cone Bodies in Newtonian Flow
The static longitudinal aerodynamic characteristics of a family of sphere-cone combinations (fineness ratios from 1.0 to 6.0) were computed by means of Newtonian impact theory. The effects of angle of attack, fineness ratio, and center-of-gravity location are shown. The results indicate that, with the center of gravity at or near the center of volume, the sphere-cone combinations are statically stable at trim points that provide low to moderate lift-drag ratios. In general, the lift-drag ratio increased with increasing fineness ratio. As an example, with the center of gravity at the center of volume, the lift-drag ratio at trim was increased from approximately 0.05 to 0.56 by increasing the fineness ratio from 1.2 to 6.0.
Dickey, Robert R.↗
Theory of idealized two-dimensional ballute in Newtonian hypersonic flow
A differential equation governing the geometry of a two-dimensional ballute in hypersonic flow and its constraining boundary conditions are derived under idealized assumptions. By solving these equations, the shape of the ballute is determined over a range of conditions. Lift, drag, pitching moment, and the allowed limit of center-of-gravity location for stability (meta-center) are then calculated using Newtonian hypersonic approximation. It is shown that the meta-center occurs near the forward end because of compliance of the ballute membrane to the shock layer pressures, especially at low free-stream densities. In order for the vehicle employing the ballute to be stable at all densities, the center of gravity must be within approximately the forward 20 percent of overall length of the vehicle. However, typical flight trajectories of an aeroassisted orbital transfer vehicle employing the ballute for aerobraking show that the vehicle may be able to complete its atmospheric flight without tumbling provided that the center of gravity is located within the forward 43 percent of the vehicle length because of the relatively short duration of flight through the destabilizing low-density regime.
Park, C.↗
Moon model - An offset core.
The lunar model proposed helps to account for the offset of the center of gravity from the center of the optical figure, the moments of inertia of the Moon, the 'mascons,' the localization of the maria basins on the near side of the Moon, the igneous nature of rocks, and the remanent magnetism. In the proposed model the Moon has a core whose center is offset from the center of the outside spheroid towards the earth. Such a core will be formed if the Moon were entirely molten at some time in its past, and on solidification was synchronous with the earth.
Ransford, G.↗
Simplified aeroelastic modeling of horizontal axis wind turbines
Certain aspects of the aeroelastic modeling and behavior of the horizontal axis wind turbine (HAWT) are examined. Two simple three degree of freedom models are described in this report, and tools are developed which allow other simple models to be derived. The first simple model developed is an equivalent hinge model to study the flap-lag-torsion aeroelastic stability of an isolated rotor blade. The model includes nonlinear effects, preconing, and noncoincident elastic axis, center of gravity, and aerodynamic center. A stability study is presented which examines the influence of key parameters on aeroelastic stability. Next, two general tools are developed to study the aeroelastic stability and response of a teetering rotor coupled to a flexible tower. The first of these tools is an aeroelastic model of a two-bladed rotor on a general flexible support. The second general tool is a harmonic balance solution method for the resulting second order system with periodic coefficients. The second simple model developed is a rotor-tower model which serves to demonstrate the general tools. This model includes nacelle yawing, nacelle pitching, and rotor teetering. Transient response time histories are calculated and compared to a similar model in the literature. Agreement between the two is very good, especially considering how few harmonics are used. Finally, a stability study is presented which examines the effects of support stiffness and damping, inflow angle, and preconing.
Wendell, J. H.↗
Design sensitivity analysis for an aeroelastic optimization of a helicopter blade
The sensitivity of vibratory hub loads of a four-bladed hingeless rotor with respect to blade design parameters is investigated using a finite element formulation in space and time. Design parameters include nonstructural mass distribution (spanwise and chordwise), chordwise offset of center of gravity from aerodynamic center, blade bending stiffnesses (flap, lag and torsion). Hub loads selected are 4/rev vertical hub shear and 3/rev hub moment in the rotating reference frame. The sensitivity derivatives of vertical hub loads with respect to blade design parameters are compared using two approaches, finite difference scheme and analytical approach using chain rule differentiation. The analytical derivative approach developed as an integral part of response solution (finite element in time) is a powerful method for an aeroelastic optimization of a helicopter rotor.
Lim, Joon↗
Aeroelastic optimization of an advanced geometry helicopter rotor
Sensitivity derivatives of blade loads and aeroelastic stability of a helicopter rotor in forward flight are calculated as an integral part of a basic aeroelastic analysis using a direct analytical approach. Design variables include nonstructural mass and its placement, chordwise offset of blade center of gravity and aerodynamic center from the elastic axis, blade bending stiffnesses (flap, lag, torsion), and tip geometry (sweep, anhedral, pretwist and planform taper). By means of a sensitivity study, the importance of different design variables on oscillatory hub loads and damping of blade modes is examined. Aeroelastic and sensitivity analyses of the rotor based on a finite element method in space and time are linked with automated optimization algorithms to perform optimization studies of rotor blades. Optimum design solutions, calculated for a four-bladed, soft-inplane hingeless rotor achieved a reduction of 25-60 percent of all 4/rev loads.
Ganguli, Ranjan↗
Static Controls Performance Tool for Lunar Landers
This document presents a static analysis tool used to evaluate the controllability of Lunar landers. This was created as part of the NASA Lunar Cargo Transportation and Landing by Soft Touchdown (Lunar CATALYST) program. This tool is capable of accepting typical design information such as location and direction of thrusters, maximum thruster forces, gravity vectors, and center of mass locations. The tool evaluates how far the center of gravity can move from its starting position while still maintaining control. This type of analysis is intended to support results produced by time domain simulations. The code created for this project was implemented in Python, and it was designed to be integrated into systems level optimization tools to yield first-cut results on optimal thruster placement.
Aretskin-Hariton, Eliot D.↗
Effects of Different Heave Motion Components on Pilot Pitch Control Behavior
The study described in this paper had two objectives. The first objective was to investigate if a different weighting of heave motion components decomposed at the center of gravity, allowing for a higher fidelity of individual components, would result in pilot manual pitch control behavior and performance closer to that observed with full aircraft motion. The second objective was to investigate if decomposing the heave components at the aircraft's instantaneous center of rotation rather than at the center of gravity could result in additional improvements in heave motion fidelity. Twenty-one general aviation pilots performed a pitch attitude control task in an experiment conducted on the Vertical Motion Simulator at NASA Ames under different hexapod motion conditions. The large motion capability of the Vertical Motion Simulator also allowed for a full aircraft motion condition, which served as a baseline. The controlled dynamics were of a transport category aircraft trimmed close to the stall point. When the ratio of center of gravity pitch heave to center of gravity heave increased in the hexapod motion conditions, pilot manual control behavior and performance became increasingly more similar to what is observed with full aircraft motion. Pilot visual and motion gains significantly increased, while the visual lead time constant decreased. The pilot visual and motion time delays remained approximately constant and decreased, respectively. The neuromuscular damping and frequency both decreased, with their values more similar to what is observed with real aircraft motion when there was an equal weighting of the heave of the center of gravity and heave due to rotations about the center of gravity. In terms of open- loop performance, the disturbance and target crossover frequency increased and decreased, respectively, and their corresponding phase margins remained constant and increased, respectively. The decomposition point of the heave components only had limited effects on pilot manual control behavior and performance.
manual control↗
A New Global Regression Analysis Method for the Prediction of Wind Tunnel Model Weight Corrections
A new global regression analysis method is discussed that predicts wind tunnel model weight corrections for strain-gage balance loads during a wind tunnel test. The method determines corrections by combining "wind-on" model attitude measurements with least squares estimates of the model weight and center of gravity coordinates that are obtained from "wind-off" data points. The method treats the least squares fit of the model weight separate from the fit of the center of gravity coordinates. Therefore, it performs two fits of "wind- off" data points and uses the least squares estimator of the model weight as an input for the fit of the center of gravity coordinates. Explicit equations for the least squares estimators of the weight and center of gravity coordinates are derived that simplify the implementation of the method in the data system software of a wind tunnel. In addition, recommendations for sets of "wind-off" data points are made that take typical model support system constraints into account. Explicit equations of the confidence intervals on the model weight and center of gravity coordinates and two different error analyses of the model weight prediction are also discussed in the appendices of the paper.
strain-gage balance↗
Prelaunch testing of the GEOS-3 laser reflector array
The prelaunch testing performed on the Geos-3 laser reflector array before launch was used to determine the lidar cross section of the array and the distance of the center of gravity of the satellite from the center of gravity of reflected laser pulses as a function of incidence angle. Experimental data are compared to computed results.
Minott, P. O.↗