Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite structure manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Processing and Properties of Vacuum Assisted Resin Transfer Molded Phenylethynyl Terminated Imide Composites

Polyimide composites are very attractive for applications that require a high strength to weight ratio and thermal stability. Recent work at NASA Langley Research Center (LaRC) has concentrated on developing new polyimide resin systems that can be processed without the use of an autoclave for advanced aerospace applications. Due to their low melt viscosities and long melt stability, certain phenylethynyl terminated imides (PETI) can be processed into composites using high temperature vacuum assisted resin transfer molding (HT-VARTM). VARTM has shown the potential to reduce the manufacturing cost of composite structures. In the current study, two PETI resins, LARC(Trademark) PETI-330 and LARC(Trademark) PETI-9, were infused into carbon fiber preforms at 260 C and cured at temperatures up to 371 C. Photomicrographs of polished cross sections were taken and void contents, determined by acid digestion, were below 4.5%. Mechanical properties including short block compression (SBC), compression after impact (CAI), and open hole compression (OHC) were determined at room temperature, 177 C, and 288 C. Both PETI-9 and PETI-330 composites demonstrated very good retention of mechanical properties at elevated temperatures. SBC and OHC properties after aging for 1000 hours at temperatures up to 288 C were also determined.

Cano, Roberto J.↗
NASA NTRS2011

Method for Selective Cleaning of Mold Release from Composite Honeycomb Surfaces

Honeycomb structures are commonly employed as load- and force-bearing structures as they are structurally strong and lightweight. Manufacturing processes for heat-molded composite honeycomb structures commence with the placement of pre-impregnated composite layups over metal mandrels. To prevent permanent bonding between the composite layup and the metal mandrels, an agent, known as a mold release agent, is used. Mold release agents allow the molded composite material to be removed from mandrels after a heat-forming process. Without a specific removal process, mold release agents may continue to adhere to the surface of the composite material, thereby affecting the bonding of other materials that may come into contact with the composite surface in later stages of processing A constituent common to commercially available household cleaning agents is employed for the removal of mold release agents common to the manufacturing of heat-formed composite materials. The reliability of the solvent has been proven by the longevity and reliability of commercial household cleaners. At the time of this reporting, no one has attempted using constituent for this purpose. The material to be cleaned is immersed in the solution, vertically removed so that the solution is allowed to drain along cell walls and into a solvent bath, and then placed on a compressed airflow table for drying.

Pugel, Diane↗
NASA NTRS2019

Automated Fiber Placement of Composite Wind Tunnel Blades: Process Planning and Manufacturing

The ability to accurately manufacture large complex shapes in a consistent and repeatable manner has led to Automated Fiber Placement (AFP) being the predominant mode of manufacturing for large composite aerospace structures today. Currently, AFP is being considered for medium- and small-scale parts. Composite wind tunnel blades have traditionally been fabricated by hand layup for pre-impregnated or dry fabrics with resin infusion. Though well proven, the traditional fabrication method is laborious and tedious, and hence expensive. The project described in this paper used the Integral Structural Assembly of Advanced Composites (ISAAC) facility at the NASA Langley Research Center to build a manufacturing demonstration unit (MDU) with a shape representative of a wind tunnel blade. This MDU is used to discuss tooling, process planning, and fabrication. Additionally, details of the generic manufacturing workflow are presented.

Harik, Ramy↗
NASA NTRS2012

Face-Sheet Quality Analysis and Thermo-Physical Property Characterization of OOA and Autoclave Panels

Increased application of polymer matrix composite (PMC) materials in large vehicle structures requires consideration of non-autoclave manufacturing technology. The NASA Composites for Exploration project, and its predecessor, Lightweight Spacecraft Structures and Materials project, were tasked with the development of materials and manufacturing processes for structures that will perform in a heavy-lift-launch vehicle environment. Both autoclave and out of autoclave processable materials were considered. Large PMC structures envisioned for such a vehicle included the payload shroud and the interstage connector. In this study, composite sandwich panels representing 1/16th segments of the barrel section of the Ares V rocket fairing were prepared as 1.8 m x 2.4 m sections of the 10 m diameter arc segment. IM7/977-3 was used as the face-sheet prepreg of the autoclave processed panels and T40-800B/5320-1 for the out of autoclave panels. The core was 49.7 kg/sq m (3.1 lb/cu ft (pcf)) aluminum honeycomb. Face-sheets were fabricated by automated tape laying 153 mm wide unidirectional tape. This work details analysis of the manufactured panels where face-sheet quality was characterized by optical microscopy, cured ply thickness measurements, acid digestion, and thermal analysis.

Miller, Sandi G.↗
NASA NTRS2012

Face-Sheet Quality Analysis and Thermo-Physical Property Characterization of OOA and Autoclave Panels

Increased application of polymer matrix composite (PMC) materials in large vehicle structures requires consideration of non-autoclave manufacturing technology. The NASA Composites for Exploration project, and its predecessor, Lightweight Spacecraft Structures and Materials project, were tasked with the development of materials and manufacturing processes for structures that will perform in a heavy-lift-launch vehicle environment. Both autoclave and out of autoclave processable materials were considered. Large PMC structures envisioned for such a vehicle included the payload shroud and the interstage connector. In this study, composite sandwich panels representing 1/16th segments of the barrel section of the Ares V rocket fairing were prepared as 1.8 m x 2.4 m sections of the 10 m diameter arc segment. IM7/977-3 was used as the face-sheet prepreg of the autoclave processed panels and T40-800B/5320-1 for the out of autoclave panels. The core was 49.7 kilograms per square meters (3.1 pounds per cubic feet (pcf)) aluminum honeycomb. Face-sheets were fabricated by automated tape laying 153 mm wide unidirectional tape. This work details analysis of the manufactured panels where face-sheet quality was characterized by optical microscopy, cured ply thickness measurements, acid digestion, and thermal analysis.

Miller, Sandi G.↗
NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include an assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite materials were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding of candidate materials to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗
NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ®†† in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi- isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non- destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Laser↗
NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ® in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi-isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non-destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Thermoplastic Composites↗
NASA NTRS1984

Study of utilization of advanced composites in fuselage structures of large transports

The effort required by the transport aircraft manufacturers to support the introduction of advanced composite materials into the fuselage structure of future commercial and military transport aircraft is investigated. Technology issues, potential benefits to military life cycle costs and commercial operating costs, and development plans are examined. The most urgent technology issues defined are impact dynamics, acoustic transmission, pressure containment and damage tolerance, post-buckling, cutouts, and joints and splices. A technology demonstration program is defined and a rough cost and schedule identified. The fabrication and test of a full-scale fuselage barrel section is presented. Commercial and military benefits are identified. Fuselage structure weight savings from use of advanced composites are 16.4 percent for the commercial and 21.8 percent for the military. For the all-composite airplanes the savings are 26 percent and 29 percent, respectively. Commercial/operating costs are reduced by 5 percent for the all-composite airplane and military life cycle costs by 10 percent.

Jackson, A. C.↗
NASA NTRS1991

Advanced composite structural concepts and material technologies for primary aircraft structures

Structural weight savings using advanced composites have been demonstrated for many years. Most military aircraft today use these materials extensively and Europe has taken the lead in their use in commercial aircraft primary structures. A major inhibiter to the use of advanced composites in the United States is cost. Material costs are high and will remain high relative to aluminum. The key therefore lies in the significant reduction in fabrication and assembly costs. The largest cost in most structures today is assembly. As part of the NASA Advanced Composite Technology Program, Lockheed Aeronautical Systems Company has a contract to explore and develop advanced structural and manufacturing concepts using advanced composites for transport aircraft. Wing and fuselage concepts and related trade studies are discussed. These concepts are intended to lower cost and weight through the use of innovative material forms, processes, structural configurations and minimization of parts. The approach to the trade studies and the downselect to the primary wing and fuselage concepts is detailed. The expectations for the development of these concepts is reviewed.

Jackson, Anthony↗
NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗
NASA NTRSDate not supplied

TPSAS-NF1676L-27788-DND

NASA Advanced Composites Project (ACP) - Reduce timeline required for development and certification of advanced composite structures by 30 percent Manufacturing Defects - Detrimentally affect quality of parts - Lead to higher cost and cause significant delay Developed guided wave-based technique for detection of manufacturing defects in carbon fiber reinforced polymer (CFRP) composites Extended guided wave - based technique for in-situcure monitoring of composites using high temperature piezoelectric transducers Incorporated embedded fiber Bragg grating (FBG) sensors for guided wave sensing during cure.

Tyler B Hudson↗
NASA NTRS1978

Toward a laminar-flow-control transport

Analyses were conducted to define a practical design for an advanced technology laminar flow control (LRC) transport for initial passenger operation in the early 1990's. Mission requirements, appropriate design criteria, and level of technology for the study aircraft were defined. The characteristics of the selected configuration were established, aircraft and LFC subsystems compatible with the mission requirements were defined, and the aircraft was evaluated in terms of fuel efficiency. A wing design integrating the LFC ducting and metering system into advanced composite wing structure was developed, manufacturing procedures for the surface panel design were established, and environmental and structural testing of surface panel components were conducted. Test results revealed a requirement for relatively minor changes in the manufacturing procedures employed, but have shown the general compatibility of both the selected design and the use of composite materials with the requirements of LFC wing surface panels.

Sturgeon, R. F.↗
NASA NTRS1985

Develop and demonstrate manufacturing processes for fabricating graphite filament reinforced polymide (Gr/PI) composite structural elements

A study was conducted to assess the merits of using graphite/polyimide, NR-150B2 resin, for structural applications on advanced space launch vehicles. The program was divided into two phases: (1) Fabrication Process Development; and (2) Demonstration Components. The first phase of the program involved the selection of a graphite fiber, quality assurance of the NR-150B2 polyimide resin, and the quality assurance of the graphite/polyimide prepreg. In the second phase of the program, a limited number of components were fabricated before the NR-150B2 resin system was removed from the market by the supplier, Du Pont. The advancement of the NR-150B2 polyimide resin binder was found to vary significantly based on previous time and temperature history during the prepregging operation. Strength retention at 316C (600F) was found to be 50% that of room temperature strength. However, the composite would retain its initial strength after 200 hours exposure at 316C (600F). Basic chemistry studies are required for determining NR-150B2 resin binder quality assurance parameters. Graphite fibers are available that can withstand high temperature cure and postcure cycles.

Chase, V. A.↗
NASA NTRS1991

Open-Section Composite Structural Elements

Report describes investigation of manufacture and mechanical properties of graphite-fiber/aluminum-matrix open-section structural elements; e.g., channels and angle bars. Conducted with view toward using such elements to build lightweight, thermally stable truss structures in outer space. Other applications transport to, and assembly at, remote or otherwise uninviting locations. Advantages include shapes permitting high packing density during shipment, convenient paths for routing tubes, hoses, and cables; accessibility of both inner and outer surfaces for repair; and ease of attachment of additional hardware. Easier and require less equipment to fabricate, and more amenable to automated fabrication and assembly at remote site. Disadvantages, not as resistant to some kinds of deformation under load.

Loftin, T. A.↗
NASA NTRSDate not supplied

Integration of Structural Analysis and Manufacturing Process Planning for Global Optimization with Automated Fiber Placement

Design of mass-efficient composite structures intended for Automated Fiber Placement (AFP) requires close interaction between structural analysis and manufacturing process planning. Tools exist for each of these disciplines, but software interplay has been insufficient for rapid and efficient design iteration. Within the NASA Advanced Composites Consortium (ACC), the Design for Manufacturing (DFM) task has made significant progress towards linking these disciplines and respective software – HyperX (design), CAPP (process planning), and VCP (tool path generation). The initial focus in previous work was on data exchange between disciplines. The ability to both export and consume composite design and manufacturing data to and from each tool. This paper focuses on the effort to automate and streamline the connection between the tools listed above, with the goal of being able to automatically generate a composite AFP design that is mass-efficient and manufacturable. The optimization method being pursued is a bi-level approach, where each tool performs optimization within its discipline. The optimization in HyperX is focused on mass and laminate strength, while CAPP is focused on maximizing manufacturability. VCP is used to generate fiber paths for each design iteration. These sub-processes are wrapped with a global level optimization, driven by HyperX, used to converge the design. This paper describes the current state of this effort, which is a completed HyperX-VCP iteration loop and initial work on the HyperX-CAPP iteration loop. Additionally, example results are shown for a wind blade structure with double curvature.

Automated Fiber Placement↗
NASA NTRS2012

Innovative Approaches to Space-Based Manufacturing and Rapid Prototyping of Composite Materials

The ability to deploy large habitable structures, construct, and service exploration vehicles in low earth orbit will be an enabling capability for continued human exploration of the solar system. It is evident that advanced manufacturing methods to fabricate replacement parts and re-utilize launch vehicle structural mass by converting it to different uses will be necessary to minimize costs and allow flexibility to remote crews engaged in space travel. Recent conceptual developments and the combination of inter-related approaches to low-cost manufacturing of composite materials and structures are described in context leading to the possibility of on-orbit and space-based manufacturing.

Hill, Charles S.↗
NASA NTRS1992

Proof test methodology for composites

The special requirements for proof test of composites are identified based on the underlying failure process of composites. Two proof test methods are developed to eliminate the inevitable weak fiber sites without also causing flaw clustering which weakens the post-proof-test composite. Significant reliability enhancement by these proof test methods has been experimentally demonstrated for composite strength and composite life in tension. This basic proof test methodology is relevant to the certification and acceptance of critical composite structures. It can also be applied to the manufacturing process development to achieve zero-reject for very large composite structures.

Wu, Edward M.↗